- 27 Jun, 2018 3 commits
-
-
Petr Machata authored
- Change the indentation of the function body from 7 spaces to one tab. - Move initialization of weights_ratio up so that it can be referenced from the error message about packet difference being zero. - Move |'s consistently to continuation line, which reindent. Signed-off-by:
Petr Machata <petrm@mellanox.com> Reviewed-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Petr Machata authored
This function will be useful for the GRE multipath test that is coming later. Signed-off-by:
-
Kees Cook authored
It looks like the prior VLA removal, commit b16520f7 ("net/tls: Remove VLA usage"), and a new VLA addition, commit c46234eb ("tls: RX path for ktls"), passed in the night. This removes the newly added VLA, which happens to have its bounds based on the same max value. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
-
- 26 Jun, 2018 37 commits
-
-
Petr Machata authored
The IP addresses of tunnel endpoint at H3 are set at the VLAN device $h3.555. Therefore when test_gretap_untagged_egress() sets vlan 555 to egress untagged at $swp3, $h3's rp_filter rejects these packets. The test then spuriously fails. Therefore turn off net.ipv4.conf.{all, $h3}.rp_filter. Fixes: 9c7c8a82 ("selftests: forwarding: mirror_gre_vlan_bridge_1q: Add more tests") Signed-off-by: -
Kees Cook authored
In the quest to remove all stack VLA usage from the kernel[1], this allocates the values buffer during the callback instead of putting it on the stack. [1] https://lkml.kernel.org/r/CA+55aFzCG-zNmZwX4A2FQpadafLfEzK6CC=qPXydAacU1RqZWA@mail.gmail.comSigned-off-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
-
David S. Miller authored
Jakub Kicinski says: ==================== net: sched: support replay of filter offload when binding to block This series from John adds the ability to replay filter offload requests when new offload callback is being registered on a TC block. This is most likely to take place for shared blocks today, when a block which already has rules is bound to another interface. Prior to this patch set if any of the rules were offloaded the block bind would fail. A new tcf_proto_op is added to generate a filter-specific offload request. The new 'offload' op is supporting extack from day 0, hence we need to propagate extack to .ndo_setup_tc TC_BLOCK_BIND/TC_BLOCK_UNBIND and through tcf_block_cb_register() to tcf_block_playback_offloads(). The immediate use of this patch set is to simplify life of drivers which require duplicating rules when sharing blocks. Switch drivers (mlxsw) can bind ports to rule lists dynamically, NIC drivers generally don't have that ability and need the rules to be duplicated for each ingress they match on. In code terms this means that switch drivers don't register multiple callbacks for each port. NIC drivers do, and get a separate request and hance rule per-port, as if the block was not shared. The registration fails today, however, if some rules were already present. As John notes in description of patch 7, drivers which register multiple callbacks to shared blocks will likely need to flush the rules on block unbind. This set makes the core not only replay the the offload add requests but also offload remove requests when callback is unregistered. v2: - name parameters in patch 2; - use unsigned int instead of u32 for in_hw_coun; - improve extack message in patch 7. ==================== Signed-off-by: -
John Hurley authored
Call the reoffload tcf_proto_op on all tcf_proto nodes in all chains of a block when a callback tries to register to a block that already has offloaded rules. If all existing rules cannot be offloaded then the registration is rejected. This replaces the previous policy of rejecting such callback registration outright. On unregistration of a callback, the rules are flushed for that given cb. The implementation of block sharing in the NFP driver, for example, duplicates shared rules to all devs bound to a block. This meant that rules could still exist in hw even after a device is unbound from a block (assuming the block still remains active). Signed-off-by:
John Hurley <john.hurley@netronome.com> Signed-off-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
John Hurley authored
Add the offload tcf_proto_op in cls_bpf to generate an offload message for each bpf prog in the given tcf_proto. Call the specified callback with this new offload message. The function only returns an error if the callback rejects adding a 'hardware only' prog. A prog contains a flag to indicate if it is in hardware or not. To ensure the offload function properly maintains this flag, keep a reference counter for the number of instances of the prog that are in hardware. Only update the flag when this counter changes from or to 0. Signed-off-by:
-
John Hurley authored
Add the offload tcf_proto_op in cls_u32 to generate an offload message for each filter and the hashtable in the given tcf_proto. Call the specified callback with this new offload message. The function only returns an error if the callback rejects adding a 'hardware only' rule. A filter contains a flag to indicate if it is in hardware or not. To ensure the offload function properly maintains this flag, keep a reference counter for the number of instances of the filter that are in hardware. Only update the flag when this counter changes from or to 0. Signed-off-by:
-
John Hurley authored
Add the reoffload tcf_proto_op in matchall to generate an offload message for each filter in the given tcf_proto. Call the specified callback with this new offload message. The function only returns an error if the callback rejects adding a 'hardware only' rule. Ensure matchall flags correctly report if the rule is in hw by keeping a reference counter for the number of instances of the rule offloaded. Only update the flag when this counter changes from or to 0. Signed-off-by:
-
John Hurley authored
Add the reoffload tcf_proto_op in flower to generate an offload message for each filter in the given tcf_proto. Call the specified callback with this new offload message. The function only returns an error if the callback rejects adding a 'hardware only' rule. A filter contains a flag to indicate if it is in hardware or not. To ensure the reoffload function properly maintains this flag, keep a reference counter for the number of instances of the filter that are in hardware. Only update the flag when this counter changes from or to 0. Add a generic helper function to implement this behaviour. Signed-off-by:
-
John Hurley authored
Create a new tcf_proto_op called 'reoffload' that generates a new offload message for each node in a tcf_proto. Pointers to the tcf_proto and whether the offload request is to add or delete the node are included. Also included is a callback function to send the offload message to and the option of priv data to go with the cb. Signed-off-by:
-
John Hurley authored
Pass the extact struct from a tc qdisc add to the block bind function and, in turn, to the setup_tc ndo of binding device via the tc_block_offload struct. Pass this back to any block callback registrations to allow netlink logging of fails in the bind process. Signed-off-by:
-
David S. Miller authored
Sergei Shtylyov says: ==================== sh_eth: RPADIR related clean-ups Here's a set of 2 patches against DaveM's 'net-next.git' repo. They are clean-ups related to RPADIR (DMA padding to NET_IP_ALIGN)... ==================== Signed-off-by: -
Sergei Shtylyov authored
If RPADIR exists, the value written to it is always the same for all SoCs (and derived from NET_IP_ALIGN), so there has not been any need to store it in the *struct* sh_eth_cpu_data... Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
-
Sergei Shtylyov authored
The *enum* RPADIR_BIT was declared in the commit 86a74ff2 ("net: sh_eth: add support for Renesas SuperH Ethernet") adding SH771x support, however the SH771x manual doesn't have the RPADIR register described and, moreover, tells why the padding insertion must not be used. The newer SoC manuals do have RPADIR documented, though with somewhat different layout -- update the *enum* according to these manuals... Signed-off-by:
-
Heiner Kallweit authored
So far unsupported WoL options are silently ignored. Change this and reject attempts to set unsupported options. This prevents situations where a user tries to set an unsupported WoL option and is under the impression it was successful because ethtool doesn't complain. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Petr Machata authored
Commit 5691484d ("net: ip6_gre: Fix headroom request in ip6erspan_tunnel_xmit()") and commit 01b8d064 ("net: ip6_gre: Request headroom in __gre6_xmit()") fix problems in reserving headroom in the packets tunneled through ip6gre/tap and ip6erspan netdevices. These two patches included snippets that reproduced the issues. This patch elevates the snippets to a full-fledged test case. Suggested-by:
-
David S. Miller authored
Guillaume Nault says: ==================== l2tp: trivial cleanups Just a set of unrelated trivial cleanups (remove unused code, make local functions static, etc.). ==================== Signed-off-by: -
Guillaume Nault authored
It always returns 0, and nobody reads the return value anyway. Signed-off-by:
Guillaume Nault <g.nault@alphalink.fr> Signed-off-by:
-
Guillaume Nault authored
Replace 'l2tp_pernet(tunnel->l2tp_net)' with 'pn', which has been set on the preceding line. Signed-off-by:
-
Guillaume Nault authored
This function is only used in l2tp_core.c. Signed-off-by:
-
Guillaume Nault authored
This function is only used in l2tp_core.c. Signed-off-by:
-
Guillaume Nault authored
This function, and the associated .priv field, are unused. Signed-off-by:
-
Guillaume Nault authored
This callback has never been implemented. Signed-off-by:
-
Guillaume Nault authored
l2tp_core.c verifies that ->session_close() is defined before calling it. There's no need for a stub. Signed-off-by:
-
David S. Miller authored
Yangbo Lu says: ==================== Support DPAA PTP clock and timestamping This patchset is to support DPAA FMAN PTP clock and HW timestamping. It had been verified on both ARM platform and PPC platform. - The patch #1 to patch #5 are to support DPAA FMAN 1588 timer in ptp_qoriq driver. - The patch #6 to patch #10 are to add HW timestamping support in DPAA ethernet driver. ==================== Signed-off-by: -
Yangbo Lu authored
Added the get_ts_info interface for ethtool to check the timestamping capability. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Acked-by:
Richard Cochran <richardcochran@gmail.com> Acked-by:
Madalin Bucur <madalin.bucur@nxp.com> Signed-off-by:
-
Yangbo Lu authored
This patch is to add hardware timestamping support for dpaa_eth. On Rx, timestamping is enabled for all frames. On Tx, we only instruct the hardware to timestamp the frames marked accordingly by the stack. Signed-off-by:
-
Yangbo Lu authored
Defined frame description command FM_FD_CMD_UPD for prepended data updating. Signed-off-by:
-
Yangbo Lu authored
This patch is to add fman_port_get_tstamp() interface to get timestamp. Signed-off-by:
-
Yangbo Lu authored
This patch is to add set_tstamp interface for memac, dtsec, and 10GEC controllers to configure HW timestamping. Signed-off-by:
-
Yangbo Lu authored
This patch is to move ptp timer node out of fman. Because ptp timer will be probed by ptp_qoriq driver, it should be an independent device in case of conflict memory mapping. Signed-off-by:
-
Yangbo Lu authored
This patch is to move ptp timer node out of fman. Because ptp timer will be probed by ptp_qoriq driver, it should be an independent device in case of conflict memory mapping. Signed-off-by:
-
Yangbo Lu authored
This patch is to add bindings description for DPAA FMan 1588 timer, and also remove its description in fsl-fman dt-bindings document. Signed-off-by:
Rob Herring <robh@kernel.org> Acked-by:
-
Yangbo Lu authored
This patch is to support DPAA (Data Path Acceleration Architecture) 1588 timer by adding "fsl,fman-ptp-timer" compatible, sharing interrupt with FMan, adding FSL_DPAA_ETH dependency, and fixing up register offset. Signed-off-by:
-
Yangbo Lu authored
This patch is to share fman event interrupt because the 1588 timer driver will also use this interrupt. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Support bridge router interfaces with non-default VLAN Petr says: When traffic is inserted on a router interface associated with an 802.1q bridge, the VLAN that the traffic appears on is determined by PVID of the bridge device itself. However currently mlxsw always configures such traffic to be forwarded to VLAN 1, regardless of the bridge PVID. Fix the problem by modifying the FID-handling code to assign such traffic not to FID that corresponds to VLAN 1, but to a FID that corresponds to the configured PVID. Bail out if there is no PVID. This is implemented in patches #1 and #2. From that point on, also forbid any changes to bridge device PVID, because such changes would not be reflected. This is implemented in patches #3, #4 and #5. Finally in patch #6, introduce tests that use bridge as a routed interface, and test mlxsw in both the currently-supported scenario of using PVID 1, and the newly-supported one of using a custom PVID. ==================== Signed-off-by: -
Petr Machata authored
Add test for cases where bridge itself acts as a router interface, with front panel port attached to the bridge in question. In the first test (router_bridge.sh), VLAN memberships are not configured in any way, and everything uses default PVID of 1. Thus traffic in $h1 and $h2 is untagged. This test ensures that the previous patches didn't break a currently working scenario. In the second test (router_bridge_vlan.sh), a VLAN 555 pvid untagged is added to the bridge CPU port, with that VLAN leaving the bridge tagged through its sole member port. The traffic is therefore expected to come out tagged at $h1. This tests the fix introduced in the previous patches. Signed-off-by:
-
Petr Machata authored
When traffic passes through a router port, it needs to be assigned a FID for ASIC to forward correctly. For bridges, this FID used to be the one corresponding to VLAN 1. In a previous patch, this was changed to instead use the PVID at the time that the RIF is created. This patch guards PVID changes after the RIF was introduced. Signed-off-by:
-
