GitLab

The firmware inverts the order of the SSIDs sent out in probe requests
(for some reason).  For regular scans, we've been passing the SSIDs in
the opposite order so they go out in the order we want.  With
scheduled scans, we were not doing that, so they were sent out in
reverse order of priority.  Fix that by using the reverse order when
populating the SSIDs array for scheduled scans as well.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The only difference in the ssid_bitmap between LMAC and UMAC scans is
that in LMAC bits 1 to 20 are used, while in UMAC bits 0 to 19 are
used (*sigh*).  So we can combine the bitmap creation into a single
function and simply shift left if LMAC is used.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Many parameters are common for all scans.  Instead of parsing the
cfg80211 scan and sched scan requests differently in each flow, move
the parsing outside of the API/scan-type specific functions.  In this
way, we only need to differentiate between scan types once.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Similarly to the regular scan patch, a lot of the UMAC and LMAC sched
scan code is also almost identical.  Grab the low hanging fruits by
combining the obvious parts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

A lot of the UMAC and LMAC scan code is almost identical.  Grab the
low hanging fruits by combining the obvious parts.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The lists of the devices supported by either MVM or DVM
firmwares was incomplete. Point to
https://wireless.wiki.kernel.org/en/users/drivers/iwlwifi#firmware


instead of maintaining the lists.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Usually during HW recovery the state of all active interfaces is cleaned
up during drv_start(). There's a special case where a HW restart is
requested when an interface is going down. In this case the iface-iterator
won't see this interface and we won't clean it. This has bad consequences
once the interface is legitimately brought up again.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of repeating the same code in 4 different places, combine the
comparisons into a new function.  Additionally, this change fixes UMAC
scans where the RRM IEs were not taken into consideration when
calculating the IE length.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We have a function (iwl_mvm_scan_size()) that can calculate the scan
size for both UMAC and LMAC scans.  Use that function instead of
calculating manually for LMAC scan and sched scan.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

We don't support -9.ucode so, all the released firmwares
support scheduled scan properly.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Remove unused struct iwl_scan_offload_req and enum
iwl_scan_offload_flags which are not used anymore.  Rename
iwl_scan_offload_schedule to iwl_scan_schedule_lmac to make it clear
that this is for LMAC only.  And fix a small typo.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Previously there was a check that compared window->average_tpt
to some value, and if it was different - it set it to that
value. However, this value was already calculated and set in
_rs_collect_tx_data(), so the entire check is unneeded.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

This adds support for configuring and retrieving the FW
monitor in MARBH mode.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Net-detect scans were using the same type as sched scan, which was
causing the driver to return -EBUSY and prevent the system from
suspending if there was an ongoing scheduled scan.  To avoid this, add
a new type for net-detect and don't stop anything when it is
requested, so that the existing scheduled scan will be resumed when
the system wakes up.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Move all the scan code that was in mac80211.c to scan.c where it
belongs, leaving only the parts that are specific to mac80211 ops.

Change some function definitions slightly to improve consistency.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

All scans are using the unified APIs now, so using "unified" in the
symbols is useless and just make them much longer and the main
difference between scans now is LMAC vs. UMAC.  Remove "unified" from
all relevant symbols.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Instead of hardcoding the differences between UMAC scans and LMAC
scans (which in this case is the number of simultaneous scans that can
run), introduce a max_scans variable and stop scans of the other type
(i.e. stop sched scan if regular scan is being attempted and
vice-versa) if the number of running scans reached the maximum.

Add a function that checks if the maximum number of scans was reached
and stops the appropriate scan to make room for the new scan.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If a new scan cannot be run for some reason, we shouldn't cancel other
ongoing scans.  Move the checks to before the code that cancels other
scans.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Now that we have separate flags for stopping scans, we don't need to
wait for the scan stopped work to complete before starting the new
scan.  Previously we needed it because we had no way of distinguishing
the scan that was being stopped from the scan that was currently
running.  With the new flags there won't be any confusions and we are
able to handle the stop for the correct type of scan.

Thus we can remove the iwl_mvm_cancel_scan_wait_notif() function.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

LMAC scans cannot handle more than one scan at a time, but UMAC scans
can.  To avoid confusion we should combine the states of these two
types of scans.  To do so, we need to support mutliple scans at the
same time for UMAC.

This commit changes the scan_status element from a single value to a
bitmask of running scan types for LMAC.  Later, we will modify UMAC
scans to use the same state bitmask.

Additionally, add stopping scan flags for scheduled and regular scans.
This makes it easier to differentiate and handle stop requests
triggered by the driver and spontaneous stops generated by the
firmware.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In some cases, max_out_time value is smaller than 200 and having the
NL80211_SCAN_FLAG_LOW_PRIORITY flag was actually causing the
max_out_time to be increased.  To avoid that, set max_out_time to 200
only if it's greater than 200.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Add scan parameters information to make it easier to debug scan dwell
times and fragmentation.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

last_txrate_idx isn't used anymore and can be dropped as this info
exists already somewhere else.
Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Same code appear a few lines later while the position has
no effect on the actual flow.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When user space requests mac80211 to transmit a frame off
channel, mac80211 notifies the driver, and the driver requests
a time event from the ucode, and then transmits the frame.
When the driver requests a time event, it can specify what is the allowed
max delay for starting the time event.

When the max delay is too big, this can cause a timeout in the user space,
that is waiting for the frame to be transmitted.

Currently the max delay is extremely long.

Reduce the max delay for the AUX ROC time event that is sent to the ucode.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

During firmware restart, the quota command isn't calculated multiple
times, but after the firmware restart it has to be sent, so force it.
Otherwise the firmware crashes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

I forgot to rename the CPTCFG_ prefix...

Fixes: 484b3d13

 ("iwlwifi: mvm: add debugfs entry with the number of net-detect scans")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Our device needs two different firmwares: the INIT firmware
and the operational (OPER) firmware. The first one is run
when the driver loads and it returns calibrations results
as well as the NVM. The second one implements the WiFi
protocol.

If the wlan interface is not brought up, the device is put
to low power state: no firmware will be running. When the
interface is brought up, we would run the OPER firmware
only and reuse the results of the run of the INIT firmware
when the driver was loaded. This is changing with this
patch.
We now run the INIT firmware every time mac80211 calls
start(). The penalty for that is minimal since the INIT
firwmare run fast. I now also avoid to power down the device
between the INIT and OPER firmware on certains buses.

The motivation for this change is that there are components
on the device (MFUART) that are triggered by the INIT
firmware and need the device to be powered up in order to
keep running. Powering the device down between the INIT and
OPER firmware would stop these components and prevent them
from running again since they are triggered by the INIT
firmware only.
The new flow allows this and also allows to trigger these
components again when the interface is brought up after
it has been brought down.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

In the case of a DMA mapping error on the last iteration of
the loop of the allocation of memory of the FW monitor we
indeed free the pages, but don't NULL out the page variable
thus allowing for the possibility of setting the FW monitor
variables with invalid data to use.

Fixes: c2d20201

 ("iwlwifi: pcie: add firmware monitor capabilities")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

If for some reason statistics notification received from the firmware
reports 0 in average beacon RSSI value, then skip it and avoid signal
based decisions.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Scan iteration complete notification handling uses the wrong FW API
version (version 2 instead of version 3).
Fix that by removing version 2 API which is no longer used, and using
only the updated version.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Reviewed-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

When the delay paramatere is provided, we need to stop
the collection only after the delay has elapsed.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware doesn't relate the scan to a vif. The scan is
run by a separate entity called auxiliary MAC (aka AUX MAC).
This AUX MAC needs to get Tx power limitations that are
not applied on a specific vif, but on the device as a whole.

This can be implemented by using the minimum of all the
values set by the user for all the MACs. But then we need
to ignore the limitations that come from the AP or
regulatory for a specific vif: a specific vif might have
regulatory limitations because of the channel is works on.
This limit is irrelevant for the AUX MAC.
Use the new API from mac80211: the user_power_level in
bss_conf to achieve this.

Firmware -13.ucode has already moved to this API.

Change-Id: Ifba83660f378e91b93bd46d29fe8ba35a7c168a4
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

Pull networking updates from David Miller:

 1) Add BQL support to via-rhine, from Tino Reichardt.

 2) Integrate SWITCHDEV layer support into the DSA layer, so DSA drivers
    can support hw switch offloading.  From Floria Fainelli.

 3) Allow 'ip address' commands to initiate multicast group join/leave,
    from Madhu Challa.

 4) Many ipv4 FIB lookup optimizations from Alexander Duyck.

 5) Support EBPF in cls_bpf classifier and act_bpf action, from Daniel
    Borkmann.

 6) Remove the ugly compat support in ARP for ugly layers like ax25,
    rose, etc.  And use this to clean up the neigh layer, then use it to
    implement MPLS support.  All from Eric Biederman.

 7) Support L3 forwarding offloading in switches, from Scott Feldman.

 8) Collapse the LOCAL and MAIN ipv4 FIB tables when possible, to speed
    up route lookups even further.  From Alexander Duyck.

 9) Many improvements and bug fixes to the rhashtable implementation,
    f...

Pull ARM updates from Russell King:
 "Included in this update are both some long term fixes and some new
  features.

  Fixes:

   - An integer overflow in the calculation of ELF_ET_DYN_BASE.

   - Avoiding OOMs for high-order IOMMU allocations

   - SMP requires the data cache to be enabled for synchronisation
     primitives to work, so prevent the CPU_DCACHE_DISABLE option being
     visible on SMP builds.

   - A bug going back 10+ years in the noMMU ARM94* CPU support code,
     where it corrupts registers.  Found by folk getting Linux running
     on their cameras.

   - Versatile Express needs an errata workaround enabled for CPU
     hot-unplug to work.

  Features:

   - Clean up module linker by handling out of range relocations
     separately from relocation cases we don't handle.

   - Fix a long term bug in the pci_mmap_page_range() code, which we
     hope won't impact userspace (we hope there's no users of the
     exist...

Pull s390 updates from Martin Schwidefsky:
 "The major change in this merge is the removal of the support for
  31-bit kernels.  Naturally 31-bit user space will continue to work via
  the compat layer.

  And then some cleanup, some improvements and bug fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (23 commits)
  s390/smp: wait until secondaries are active & online
  s390/hibernate: fix save and restore of kernel text section
  s390/cacheinfo: add missing facility check
  s390/syscalls: simplify syscall_get_arch()
  s390/irq: enforce correct irqclass_sub_desc array size
  s390: remove "64" suffix from mem64.S and swsusp_asm64.S
  s390/ipl: cleanup macro usage
  s390/ipl: cleanup shutdown_action attributes
  s390/ipl: cleanup bin attr usage
  s390/uprobes: fix address space annotation
  s390: add missing arch_release_task_struct() declaration
  s390: make couple of functions and variables static
  s390/maccess: improve s390_kernel_write()
  s390/maccess: remove potentially broken probe_kernel_write()
  s390/watchdog: support for KVM hypervisors and delete pr_info messages
  s390/watchdog: enable KEEPALIVE for /dev/watchdog
  s390/dasd: remove setting of scheduler from driver
  s390/traps: panic() instead of die() on translation exception
  s390: remove test_facility(2) (== z/Architecture mode active) checks
  s390/cmpxchg: simplify cmpxchg_double
  ...

Pull power management and ACPI updates from Rafael Wysocki:
 "These are mostly fixes and cleanups all over, although there are a few
  items that sort of fall into the new feature category.

  First off, we have new callbacks for PM domains that should help us to
  handle some issues related to device initialization in a better way.

  There also is some consolidation in the unified device properties API
  area allowing us to use that inferface for accessing data coming from
  platform initialization code in addition to firmware-provided data.

  We have some new device/CPU IDs in a few drivers, support for new
  chips and a new cpufreq driver too.

  Specifics:

   - Generic PM domains support update including new PM domain callbacks
     to handle device initialization better (Russell King, Rafael J
     Wysocki, Kevin Hilman)

   - Unified device properties API update including a new mechanism for
     accessin...

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2015-04-14

This series contains updates to fm10k only.

Fixed transmit statistics which was actually using values from the
receive ring, instead of the transmit ring.  Fixed up spelling mistakes
in code comments and resolved unused argument warnings.  Added support
for netconsole.  Fixed up statistic reporting so that we are only
reporting from actual queues as well as display PF only stats for
just the PF and not the VF.  Also fixed an issue that when returning
virtualization queues from the VF back to the PF, we were retaining
the VF rate limiter.

Fixed up the driver to use a separate workqueue, which helps reduce
and stabilize latency between scheduling the work in our interrupt and
actually performing the work.

Fixed a bug where the VF tried to set a multicast address before
requesting the required xcast mode.

Fix VF multicast update since VFs were being improperly added to the
switch's mutlicast group.  The error stems from the fact that incorrect
arguments were passed to the update_mc_addr().

Thanks to Alex Duyck for the extensive review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull input subsystem updates from Dmitry Torokhov:
 "You will get the following new drivers:

   - Qualcomm PM8941 power key drver
   - ChipOne icn8318 touchscreen controller driver
   - Broadcom iProc touchscreen and keypad drivers
   - Semtech SX8654 I2C touchscreen controller driver

  ALPS driver now supports newer SS4 devices; Elantech got a fix that
  should make it work on some ASUS laptops; and a slew of other
  enhancements and random fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
  Input: alps - non interleaved V2 dualpoint has separate stick button bits
  Input: alps - fix touchpad buttons getting stuck when used with trackpoint
  Input: atkbd - document "no new force-release quirks" policy
  Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
  Input: ALPS - V7 devices can report 5-finger taps
  Input: ALPS - add support for SS4 touchpad devices
  Inpu...