- 08 Apr, 2013 33 commits
-
-
Jon Hunter authored
Add the device-tree node for GPMC on OMAP2, OMAP4 and OMAP5 devices. Signed-off-by:
Jon Hunter <jon-hunter@ti.com> Signed-off-by:
Benoit Cousson <benoit.cousson@linaro.org>
-
Jon Hunter authored
Add SDMA controller binding for OMAP2+ devices and populate DMA client information for SPI and MMC peripheral on OMAP3+ devices. Please note that OMAP24xx devices do not have SPI and MMC bindings available yet and so DMA client information is not populated. Signed-off-by:
Felipe Balbi <balbi@ti.com> Acked-by:
Santosh Shilimkar <santosh.shilimkar@ti.com> Tested-by:
-
Jon Hunter authored
Add PMU nodes for OMAP2, OMAP3 and OMAP4460 devices. Please note that the node for OMAP4460 has been placed in a separate header file for OMAP4460, because the node is not compatible with OMAP4430. The node for OMAP4430 is not included because PMU is not currently supported on OMAP4430 due to the absence of a cross-trigger interface driver. Signed-off-by:
-
Jon Hunter authored
If device-tree is present, then do not create the PMU device from within the OMAP specific PMU code. This is required to allow device-tree to create the PMU device from the PMU device-tree node. PMU is not currently supported for OMAP4430 (due to a dependency on having a cross-trigger interface driver) and so ensure that this indicated on boot with or without device-tree. Signed-off-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
-
Kishon Vijay Abraham I authored
Add dwc3 omap glue data to the omap5 dt data file. The information about the dt node added here is available @ Documentation/devicetree/bindings/usb/omap-usb.txt. Also added dwc3 core dt data as a subnode to dwc3 omap glue data in omap5 dt data file. The information for the entered data node is available @ Documentation/devicetree/bindings/usb/dwc3.txt Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Kishon Vijay Abraham I authored
Add omap-usb3 and omap-usb2 data node in OMAP5 device tree file. The information for the node added here is available @ Documentation/devicetree/bindings/usb/usb-phy.txt Signed-off-by:
-
Kishon Vijay Abraham I authored
Add ocp2scp data node in omap5 device tree file. The information for the node added here can be found @ Documentation/devicetree/bindings/bus/omap-ocp2scp.txt Signed-off-by:
-
Kishon Vijay Abraham I authored
Add omap control usb data in OMAP5 device tree file. This will have the register address of registers to power on the USB2 PHY and USB3 PHY. The information for the node added here is available in Documentation/devicetree/bindings/usb/omap-usb.txt Signed-off-by:
-
Kishon Vijay Abraham I authored
Add usb otg data node in omap4/omap3 device tree file. Also update the node with board specific setting in omapx-<board>.dts file. The dt data specifies among others the interface type (ULPI or UTMI), mode which is mostly OTG, power that specifies the amount of power this can supply when in host mode. The information about usb otg node is available @ Documentation/devicetree/bindings/usb/omap-usb.txt Signed-off-by:
-
Kishon Vijay Abraham I authored
Add omap-usb2 data node in omap4 device tree file. Since omap-usb2 is connected to ocp2scp, omap-usb2 dt data is added as a child node of ocp2scp. The information about this data node is availabe @ Documentation/devicetree/bindings/usb/usb-phy.txt Signed-off-by:
-
Kishon Vijay Abraham I authored
Add omap control usb data in omap4 device tree file. This will have the register address of registers to power on the PHY and to write to mailbox. The information about this data node is available @ Documentation/devicetree/bindings/usb/omap-usb.txt Signed-off-by:
-
Javier Martinez Canillas authored
Currently the OMAP General-Purpose Memory Controller (GPMC) device node maps 16 MB of address space for its hardware registers. This is because the OMAP Technical Reference Manual says that the GPMC module register address space size is 16 MB. But in practice the maximum address offset used by a GPMC register is 0x02d0. So, there is no need to map such a big address space for GPMC regs. This change was suggested by Jon Hunter [1]. [1]: https://patchwork.kernel.org/patch/2057111/Signed-off-by:
Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by:
-
Florian Vaussard authored
Add device-tree support for the GPMC controller on the OMAP3. Signed-off-by:
Florian Vaussard <florian.vaussard@epfl.ch> Signed-off-by:
-
Sourav Poddar authored
Add mcspi node and pinmux data for omap5 mcspi controller. Tested on omap5430 evm with 3.8-rc6 custom kernel. Signed-off-by:
Sourav Poddar <sourav.poddar@ti.com> Signed-off-by:
-
Felipe Balbi authored
Add all 4 mcspi instances to omap5.dtsi file. Signed-off-by:
-
Sourav Poddar authored
Booting 3.8-rc6 on omap4 panda results in the following error [ 0.444427] omap_i2c 48070000.i2c: did not get pins for i2c error: -19 [ 0.445770] omap_i2c 48070000.i2c: bus 0 rev0.11 at 400 kHz [ 0.473937] omap_i2c 48072000.i2c: did not get pins for i2c error: -19 [ 0.474670] omap_i2c 48072000.i2c: bus 1 rev0.11 at 400 kHz [ 0.474822] omap_i2c 48060000.i2c: did not get pins for i2c error: -19 [ 0.476379] omap_i2c 48060000.i2c: bus 2 rev0.11 at 100 kHz [ 0.477294] omap_i2c 48350000.i2c: did not get pins for i2c error: -19 [ 0.477996] omap_i2c 48350000.i2c: bus 3 rev0.11 at 400 kHz [ 0.483398] Switching to clocksource 32k_counter This happens because omap4 panda dts file is not adapted to use i2c through pinctrl framework. Populating i2c pinctrl data to get rid of the error. Tested on omap4460 panda with 3.8-rc6 kernel. Signed-off-by:
Luciano Coelho <coelho@ti.com> Signed-off-by:
-
Sourav Poddar authored
Booting 3.8-rc6 on omap 5430evm results in the following error omap_i2c 48070000.i2c: did not get pins for i2c error: -19 [ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz [ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19 [ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz [ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19 [ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19 [ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz This happens because omap5 dts file is not adapted to use i2c through pinctrl framework. Populating i2c pinctrl data to get rid of the error. Tested on omap5430 evm with 3.8-rc6 kernel. Signed-off-by:
-
Florian Vaussard authored
Add the needed sections to enable audio support on Overo. Signed-off-by:
-
Sourav Poddar authored
Booting 3.8-rc6 on omap 4430sdp results in the following error omap_i2c 48070000.i2c: did not get pins for i2c error: -19 [ 1.024261] omap_i2c 48070000.i2c: bus 0 rev0.12 at 100 kHz [ 1.030181] omap_i2c 48072000.i2c: did not get pins for i2c error: -19 [ 1.037384] omap_i2c 48072000.i2c: bus 1 rev0.12 at 400 kHz [ 1.043762] omap_i2c 48060000.i2c: did not get pins for i2c error: -19 [ 1.050964] omap_i2c 48060000.i2c: bus 2 rev0.12 at 100 kHz [ 1.056823] omap_i2c 4807a000.i2c: did not get pins for i2c error: -19 [ 1.064025] omap_i2c 4807a000.i2c: bus 3 rev0.12 at 400 kHz This happens because omap4 dts file is not adapted to use i2c through pinctrl framework. Populating i2c pinctrl data to get rid of the error. Tested on omap4430 sdp with 3.8-rc6 kernel. Signed-off-by:
-
Florian Vaussard authored
Convert the on-board LED connected to the TWL4030 (LEDB) to use pwm-leds. Signed-off-by:
-
Peter Ujfalusi authored
Section to describe the backlight for the LCD panels. Signed-off-by:
Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by:
-
Peter Ujfalusi authored
Sections to describe the pwm-leds in the system. Signed-off-by:
-
Peter Ujfalusi authored
We have proper driver stack to handle the pmu_stat LED which is connected PWMB of twl4030. Signed-off-by:
-
Peter Ujfalusi authored
Enable support for the PWMs and LED as PWM drivers. Signed-off-by:
-
Peter Ujfalusi authored
Enable support for the PWMs and LEDs as PWM drivers. Signed-off-by:
-
AnilKumar Ch authored
Add a new address space/memory resource to d_can device tree node. D_CAN RAM initialization is achieved through RAMINIT register which is part of AM33XX control module address space. D_CAN RAM init or de-init should be done by writing instance corresponding value to control module register. Till we have a separate control module driver to write to control module, d_can driver will handle the register writes to control module by itself. So a new address space to represent this control module register is added to d_can driver. Signed-off-by:
AnilKumar Ch <anilkumar@ti.com> Acked-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
AnilKumar Ch authored
Add d_can instances to aliases node to get the D_CAN instance number from the driver. To initialize D_CAN message RAM, corresponding instance number is required. To initialize instance 0 message RAM then 0x1 should be written and for instance 1 message RAM, 0x2 should be written to control module register. With device-tree framework ip instance number is "-1" by default for all instances. To get device id/instance number then modules should be added to DT "aliases" node. of_alias_get_id() gives the device id number based on number of alias nodes present in "aliases node". Signed-off-by:
-
Matthias Brugger authored
This is a follow-up to Javier Martinez effort adding initial device tree support to IGEP technology devices [1]. It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards. [1] http://www.spinics.net/lists/linux-omap/msg83409.htmlSigned-off-by:
Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by:
-
Javier Martinez Canillas authored
ISEE IGEP COM Module is an TI OMAP3 SoC computer on module. This patch adds an initial device tree support to boot an IGEP COM Module from the MMC/SD. Signed-off-by:
Enric Balletbo i Serra <eballetbo@gmail.com> [b-cousson@ti.com: Update the Makefile for 3.8-rc2] Signed-off-by:
-
Javier Martinez Canillas authored
ISEE IGEPv2 is an TI OMAP3 SoC based embedded board. This patch adds an initial device tree support to boot an IGEPv2 from the MMC/SD. Currently is working everything that is supported by DT on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio). Signed-off-by:
-
Javier Martinez Canillas authored
Add a generic .dtsi device tree source file for the common characteristics across IGEP Technology devices. Signed-off-by:
-
AnilKumar Ch authored
Rename I2C and GPIO nodes according to AM33XX TRM. According to AM33XX TRM device instances are starting from "0" like i2c0, i2c1 and i2c3. Signed-off-by:
Pantelis Antoniou <panto@antoniou-consulting.com> [panto@antoniou-consulting.com: initial patch by pantelis's] Signed-off-by:
-
Benoit Cousson authored
Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged
-
- 02 Apr, 2013 7 commits
-
-
Roger Quadros authored
Provide RESET and Power regulators for the USB PHY, the USB Host port mode and the PHY device. Also provide pin multiplexer information for USB host pins. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by:
Roger Quadros <rogerq@ti.com> Signed-off-by:
-
Roger Quadros authored
Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by:
-
Roger Quadros authored
Adds device nodes for HS USB Host module, TLL module, OHCI and EHCI controllers. CC: Benoît Cousson <b-cousson@ti.com> Signed-off-by:
-
Roger Quadros authored
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by:
-
Roger Quadros authored
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by:
-
Roger Quadros authored
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by:
-
Roger Quadros authored
Use usbhs_init_phys() to register the PHY's RESET regulator and the NOP PHY device. Signed-off-by:
-
