A kernel BUG when bluetooth rfcomm connection drop while the associated
serial port is open is sometime triggered.

It seems that the line discipline can disappear between the
tty_ldisc_put and tty_ldisc_get. This patch fall back to the N_TTY line
discipline if the previous discipline is not available anymore.
Signed-off-by: Philippe Retornaz <philippe.retornaz@epfl.ch>
Acked-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

It was removed in 65b77046 (tty-ldisc: turn ldisc user count into
a proper refcount), but we need to wait for last user to quit the
ldisc before we close it in tty_set_ldisc.

Otherwise weird things start to happen. There might be processes
waiting in tty_read->n_tty_read on tty->read_wait for input to appear
and at that moment, a change of ldisc is fatal. n_tty_close is called,
it frees read_buf and the waiting process is still in the middle of
reading and goes nuts after it is woken.

Previously we prevented close to happen when others are in ldisc ops
by tty_ldisc_wait_idle in tty_set_ldisc. But the commit above removed
that. So revoke the change and test whether there is 1 user (=we), and
allow the close then.

We can do that without ldisc/tty locks, because nobody else can open
the device due to TTY_LDISC_CHANGING bit set, so we in fact wait for
everybody to leave.

I don't understand why tty_ldisc_lock would be needed either when the
counter is an atomic variable, so this is a lockless
tty_ldisc_wait_idle.

On the other hand, if we fail to wait (timeout or signal), we have to
reenable the halted ldiscs, so we take ldisc lock and reuse the setup
path at the end of tty_set_ldisc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Sebastian Andrzej Siewior <bigeasy@breakpoint.cc>
LKML-Reference: <20101031104136.GA511@Chamillionaire.breakpoint.cc>
LKML-Reference: <1287669539-22644-1-git-send-email-jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org [32, 33, 36]
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[SERIAL]blacklist si3052 chip

Si3052-based softmodems aren't serial ports so don't bind serial driver to them.
Allows proper driver to bind to them.
Signed-off-by: Maciej Szmigiero <mhej@o2.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

There's a small window inside the flush_to_ldisc function,
where the tty is unlocked and calling ldisc's receive_buf
function. If in this window new buffer is added to the tty,
the processing might never leave the flush_to_ldisc function.

This scenario will hog the cpu, causing other tty processing
starving, and making it impossible to interface the computer
via tty.

I was able to exploit this via pty interface by sending only
control characters to the master input, causing the flush_to_ldisc
to be scheduled, but never actually generate any output.

To reproduce, please run multiple instances of following code.

- SNIP
#define _XOPEN_SOURCE
#include <stdlib.h>
#include <stdio.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>

int main(int argc, char **argv)
{
        int i, slave, master = getpt();
        char buf[8192];

        sprintf(buf, "%s", ptsname(master));
        grantpt(master);
        unlockpt(master);

        slave = open(buf, O_RDWR);
        if (slave < 0) {
                perror("open slave failed");
                return 1;
        }

        for(i = 0; i < sizeof(buf); i++)
                buf[i] = rand() % 32;

        while(1) {
                write(master, buf, sizeof(buf));
        }

        return 0;
}
- SNIP

The attached patch (based on -next tree) fixes this by checking on the
tty buffer tail. Once it's reached, the current work is rescheduled
and another could run.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Cc: stable <stable@kernel.org>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Add support for Kouwell KW-L221N-2 card.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Just remove a now unused variable
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

During builds I see the following warning -

  CC [M]  drivers/char/pcmcia/synclink_cs.o
drivers/char/pcmcia/synclink_cs.c:2194: warning: ‘mgslpc_get_icount’ defined but not used

The function is a callback meant to be assigned to get_icount (added during 0587102c).
Fix accordingly.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Someone added a new ldisc number and messed up the tabbing. Fix it before
anyone else copies it.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

So properly mark it as such in the MAINTAINERS file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: Add new ext4 inode tracepoints
  ext4: Don't call sb_issue_discard() in ext4_free_blocks()
  ext4: do not try to grab the s_umount semaphore in ext4_quota_off
  ext4: fix potential race when freeing ext4_io_page structures
  ext4: handle writeback of inodes which are being freed
  ext4: initialize the percpu counters before replaying the journal
  ext4: "ret" may be used uninitialized in ext4_lazyinit_thread()
  ext4: fix lazyinit hang after removing request

* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
  TTY: move .gitignore from drivers/char/ to drivers/tty/vt/
  TTY: create drivers/tty/vt and move the vt code there
  TTY: create drivers/tty and move the tty core files there

Merge branch 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6

* 'staging-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-next-2.6:
  Staging: ath6kl: remove empty files that mess with 'distclean'
  staging: ath6kl: Fixing the driver to use modified mmc_host structure
  Staging: solo6x10: fix build problem

Merge branch 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6

* 'rmobile-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  mmc: sh_mmcif: Convert extern inline to static inline.
  ARM: mach-shmobile: Allow GPIO chips to register IRQ mappings.
  ARM: mach-shmobile: fix sh7372 after a recent clock framework rework
  ARM: mach-shmobile: include drivers/sh/Kconfig
  ARM: mach-shmobile: ap4evb: Add HDMI sound support
  ARM: mach-shmobile: clock-sh7372: Add FSIDIV clock support
  ARM: shmobile: remove sh_timer_config clk member

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: clkfwk: Fix up checkpatch warnings.
  sh: make some needlessly global sh7724 clocks static
  sh: add clk_round_parent() to optimize parent clock rate
  sh: Simplify phys_addr_mask()/PTE_PHYS_MASK for 29/32-bit.
  sh: nommu: Support building without an uncached mapping.
  sh: nommu: use 32-bit phys mode.
  sh: mach-se: Fix up SE7206 no ioport build.
  sh: intc: Update for single IRQ reservation helper.
  sh: clkfwk: Fix up rate rounding error handling.
  sh: mach-se: Rip out superfluous 7751 PIO routines.
  sh: mach-se: Rip out superfluous 770x PIO routines.
  sh: mach-edosk7705: Kill off machtype, consolidate board def.
  sh: mach-edosk7705: update for this century, kill off PIO trapping.
  sh: mach-se: Rip out superfluous 7206 PIO routines.
  sh: mach-systemh: Kill off dead board.
  sh: mach-snapgear: Kill off machtype, consolidate board def.
  sh: mach-snapgear: Rip out superfluous PIO routines.
  sh: mach-microdev: SuperIO-relative ioport mapping.

Add ext4_evict_inode, ext4_drop_inode, ext4_mark_inode_dirty, and
ext4_begin_ordered_truncate()
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

Commit 5c521830 (ext4: Support discard requests when running in
no-journal mode) attempts to add sb_issue_discard() for data blocks
(in data=writeback mode) and in no-journal mode.  Unfortunately, this
no longer works, because in commit dd3932ed (block: remove
BLKDEV_IFL_WAIT), sb_issue_discard() only presents a synchronous
interface, and there are times when we call ext4_free_blocks() when we
are are holding a spinlock, or are otherwise in an atomic context.

For now, I've removed the call to sb_issue_discard() to prevent a
deadlock or (if spinlock debugging is enabled) failures like this:

BUG: scheduling while atomic: rc.sysinit/1376/0x00000002
Pid: 1376, comm: rc.sysinit Not tainted 2.6.36-ARCH #1
Call Trace:
[<ffffffff810397ce>] __schedule_bug+0x5e/0x70
[<ffffffff81403110>] schedule+0x950/0xa70
[<ffffffff81060bad>] ? insert_work+0x7d/0x90
[<ffffffff81060fbd>] ? queue_work_on+0x1d/0x30
[<ffffffff81061127>] ? queue_work+0x37/0x60
[<ffffffff8140377d>] schedule_timeout+0x21d/0x360
[<ffffffff812031c3>] ? generic_make_request+0x2c3/0x540
[<ffffffff81402680>] wait_for_common+0xc0/0x150
[<ffffffff81041490>] ? default_wake_function+0x0/0x10
[<ffffffff812034bc>] ? submit_bio+0x7c/0x100
[<ffffffff810680a0>] ? wake_bit_function+0x0/0x40
[<ffffffff814027b8>] wait_for_completion+0x18/0x20
[<ffffffff8120a969>] blkdev_issue_discard+0x1b9/0x210
[<ffffffff811ba03e>] ext4_free_blocks+0x68e/0xb60
[<ffffffff811b1650>] ? __ext4_handle_dirty_metadata+0x110/0x120
[<ffffffff811b098c>] ext4_ext_truncate+0x8cc/0xa70
[<ffffffff810d713e>] ? pagevec_lookup+0x1e/0x30
[<ffffffff81191618>] ext4_truncate+0x178/0x5d0
[<ffffffff810eacbb>] ? unmap_mapping_range+0xab/0x280
[<ffffffff810d8976>] vmtruncate+0x56/0x70
[<ffffffff811925cb>] ext4_setattr+0x14b/0x460
[<ffffffff811319e4>] notify_change+0x194/0x380
[<ffffffff81117f80>] do_truncate+0x60/0x90
[<ffffffff811e08fa>] ? security_inode_permission+0x1a/0x20
[<ffffffff811eaec1>] ? tomoyo_path_truncate+0x11/0x20
[<ffffffff81127539>] do_last+0x5d9/0x770
[<ffffffff811278bd>] do_filp_open+0x1ed/0x680
[<ffffffff8140644f>] ? page_fault+0x1f/0x30
[<ffffffff81132bfc>] ? alloc_fd+0xec/0x140
[<ffffffff81118db1>] do_sys_open+0x61/0x120
[<ffffffff81118e8b>] sys_open+0x1b/0x20
[<ffffffff81002e6b>] system_call_fastpath+0x16/0x1b

https://bugzilla.kernel.org/show_bug.cgi?id=22302Reported-by: Mathias Burén <mathias.buren@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: jiayingz@google.com

It's not needed to sync the filesystem, and it fixes a lock_dep complaint.
Signed-off-by: Dmitry Monakhov <dmonakhov@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Jan Kara <jack@suse.cz>

Use an atomic_t and make sure we don't free the structure while we
might still be submitting I/O for that page.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>

The following BUG can occur when an inode which is getting freed when
it still has dirty pages outstanding, and it gets deleted (in this
because it was the target of a rename).  In ordered mode, we need to
make sure the data pages are written just in case we crash before the
rename (or unlink) is committed.  If the inode is being freed then
when we try to igrab the inode, we end up tripping the BUG_ON at
fs/ext4/page-io.c:146.

To solve this problem, we need to keep track of the number of io
callbacks which are pending, and avoid destroying the inode until they
have all been completed.  That way we don't have to bump the inode
count to keep the inode from being destroyed; an approach which
doesn't work because the count could have already been dropped down to
zero before the inode writeback has started (at which point we're not
allowed to bump the count back up to 1, since it's already started
getting freed).

Thanks to Dave Chinner for suggesting this approach, which is also
used by XFS.

  kernel BUG at /scratch_space/linux-2.6/fs/ext4/page-io.c:146!
  Call Trace:
   [<ffffffff811075b1>] ext4_bio_write_page+0x172/0x307
   [<ffffffff811033a7>] mpage_da_submit_io+0x2f9/0x37b
   [<ffffffff811068d7>] mpage_da_map_and_submit+0x2cc/0x2e2
   [<ffffffff811069b3>] mpage_add_bh_to_extent+0xc6/0xd5
   [<ffffffff81106c66>] write_cache_pages_da+0x2a4/0x3ac
   [<ffffffff81107044>] ext4_da_writepages+0x2d6/0x44d
   [<ffffffff81087910>] do_writepages+0x1c/0x25
   [<ffffffff810810a4>] __filemap_fdatawrite_range+0x4b/0x4d
   [<ffffffff810815f5>] filemap_fdatawrite_range+0xe/0x10
   [<ffffffff81122a2e>] jbd2_journal_begin_ordered_truncate+0x7b/0xa2
   [<ffffffff8110615d>] ext4_evict_inode+0x57/0x24c
   [<ffffffff810c14a3>] evict+0x22/0x92
   [<ffffffff810c1a3d>] iput+0x212/0x249
   [<ffffffff810bdf16>] dentry_iput+0xa1/0xb9
   [<ffffffff810bdf6b>] d_kill+0x3d/0x5d
   [<ffffffff810be613>] dput+0x13a/0x147
   [<ffffffff810b990d>] sys_renameat+0x1b5/0x258
   [<ffffffff81145f71>] ? _atomic_dec_and_lock+0x2d/0x4c
   [<ffffffff810b2950>] ? cp_new_stat+0xde/0xea
   [<ffffffff810b29c1>] ? sys_newlstat+0x2d/0x38
   [<ffffffff810b99c6>] sys_rename+0x16/0x18
   [<ffffffff81002a2b>] system_call_fastpath+0x16/0x1b
Reported-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Nick Bowler <nbowler@elliptictech.com>

Merge branches 'sh/pio-death', 'sh/nommu', 'sh/clkfwk', 'sh/core' and 'sh/intc-extension' into sh-fixes-for-linus

The clk_round_parent() change introduced various checkpatch warnings,
tidy them up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

These clocks are currently only used inside one .c file and are not
declared in any headers, therefore having them global is useless.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

Sometimes it is possible and reasonable to adjust the parent clock rate to
improve precision of the child clock, e.g., if the child clock has no siblings.
clk_round_parent() is a new addition to the SH clock-framework API, that
implements such an optimization for child clocks with divisors, taking all
integer values in a range.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>

These two .h files would get removed from the tree when doing
	make distclean

It turns out they are not needed at all, so just delete them which fixes
people's git trees when doing development.
Reported-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

While scanning the floopy code due to c093ee4f ("floppy: fix
use-after-free in module load failure path"), I found one more instance
of trying to access disk->queue pointer after doing put_disk() on
gendisk.  For some reason , floppy moule still loads/unloads fine.  The
object is probably still around with right pointer values.

 o There seems to be one more instance of trying to cleanup the request
   queue after we have called put_disk() on associated gendisk.

 o This fix is more out of code inspection.  Even without this fix for
   some reason I am able to load/unload floppy module without any
   issues.

 o Floppy module loads/unloads fine after the fix.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The autogenerated files (consolemap_deftbl.c and defkeymap.c) need to
be ignored by git, so move the .gitignore file that was doing it to the
properly location now that the files have moved as well.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

Commit 27ae60f8 ("ipw2x00: replace "ieee80211" with "libipw" where
appropriate") changed DRV_NAME to be "libipw", but didn't properly fix
up the places where it was used to specify the name for the /proc/net/
directory.

For backwards compatibility reasons, that directory name remained
"ieee80211", but due to the DRV_NAME change, the error case printouts
and the cleanup functions now used "libipw" instead.  Which made it all
fail badly.

For example, on module unload as reported by Randy:

  WARNING: at fs/proc/generic.c:816 remove_proc_entry+0x156/0x35e()
  name 'libipw'

because it's trying to unregister a /proc directory that obviously
doesn't even exist.

Clean it all up to use DRV_PROCNAME for the actual /proc directory name.
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Pavel Roskin <proski@gnu.org>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: PPC: BookE: Load the lower half of MSR
  KVM: PPC: BookE: fix sleep with interrupts disabled
  KVM: PPC: e500: Call kvm_vcpu_uninit() before kvmppc_e500_tlb_uninit().
  PPC: KVM: Book E doesn't have __end_interrupts.
  KVM: x86: Issue smp_call_function_many with preemption disabled
  KVM: x86: fix information leak to userland
  KVM: PPC: fix information leak to userland
  KVM: MMU: fix rmap_remove on non present sptes
  KVM: Write protect memory after slot swap

Commit 48821184 ("floppy: switch to one queue per drive instead of
sharing a queue") introduced a use-after-free.  We do "put_disk()" on
the disk device _before_ we then clean up the queue associated with that
disk.

Move the put_disk() down to avoid dereferencing a free'd data structure.

Cc: Jens Axboe <jaxboe@fusionio.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Reported-and-tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit d9ca07a0 ("watchdog: Avoid kernel crash when disabling
watchdog") introduces a section mismatch.

Now that we reference no_watchdog from non-__init code it can no longer
be __initdata.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
  inet_diag: Make sure we actually run the same bytecode we audited.
  netlink: Make nlmsg_find_attr take a const nlmsghdr*.
  fib: fib_result_assign() should not change fib refcounts
  netfilter: ip6_tables: fix information leak to userspace
  cls_cgroup: Fix crash on module unload
  memory corruption in X.25 facilities parsing
  net dst: fix percpu_counter list corruption and poison overwritten
  rds: Remove kfreed tcp conn from list
  rds: Lost locking in loop connection freeing
  de2104x: fix panic on load
  atl1 : fix panic on load
  netxen: remove unused firmware exports
  caif: Remove noisy printout when disconnecting caif socket
  caif: SPI-driver bugfix - incorrect padding.
  caif: Bugfix for socket priority, bindtodev and dbg channel.
  smsc911x: Set Ethernet EEPROM size to supported device's size
  ipv4: netfilter: ip_tables: fix information leak to userland
  ipv4: netfilter: arp_tables: fix information leak to userland
  cxgb4vf: remove call to stop TX queues at load time.
  cxgb4: remove call to stop TX queues at load time.
  ...

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: fix race when reading count in AR descriptor
  firewire: ohci: avoid reallocation of AR buffers
  firewire: ohci: fix race in AR split packet handling
  firewire: ohci: fix buffer overflow in AR split packet handling

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: make cifs_set_oplock_level() take a cifsInodeInfo pointer
  cifs: dereferencing first then checking
  cifs: trivial comment fix: tlink_tree is now a rbtree
  [CIFS] Cleanup unused variable build warning
  cifs: convert tlink_tree to a rbtree
  cifs: store pointer to master tlink in superblock (try #2)
  cifs: trivial doc fix: note setlease implemented
  CIFS: Add cifs_set_oplock_level
  FS: cifs, remove unneeded NULL tests

posix-cpu-timers.c correctly assumes that the dying process does
posix_cpu_timers_exit_group() and removes all !CPUCLOCK_PERTHREAD
timers from signal->cpu_timers list.

But, it also assumes that timer->it.cpu.task is always the group
leader, and thus the dead ->task means the dead thread group.

This is obviously not true after de_thread() changes the leader.
After that almost every posix_cpu_timer_ method has problems.

It is not simple to fix this bug correctly. First of all, I think
that timer->it.cpu should use struct pid instead of task_struct.
Also, the locking should be reworked completely. In particular,
tasklist_lock should not be used at all. This all needs a lot of
nontrivial and hard-to-test changes.

Change __exit_signal() to do posix_cpu_timers_exit_group() when
the old leader dies during exec. This is not the fix, just the
temporary hack to hide the problem for 2.6.37 and stable. IOW,
this is obviously wrong but this is what we currently have anyway:
cpu timers do not work after mt exec.

In theory this change adds another race. The exiting leader can
detach the timers which were attached to the new leader. However,
the window between de_thread() and release_task() is small, we
can pretend that sys_timer_create() was called before de_thread().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (ltc4261) Fix error message format
  hwmon: (ltc4261) Add missing newline in debug message

All the callers already have a pointer to struct cifsInodeInfo. Use it.
Signed-off-by: Suresh Jayaraman <sjayaraman@suse.de>
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>

adapter->id is deprecated and not set by any adapter driver, so this
was certainly not what the author wanted to use. adapter->nr maybe,
but as dev_err() already includes this value, as well as the client's
address, there's no point repeating them. Better print a simple error
message in plain English words.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>

Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>