Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This hasn't been necessary for a long time now..
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Fixes a case where we don't get separate supervisor interrupt sequences for
disconnect and modeset events.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Should fix issues with kexec, and as a nice side bonus, the code to avoid
having PDISP disappear will also fix hibernate on those effected systems.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This has the effect of ensuring the encoders which were active before we
loaded get disconnected properly before we start reprogramming them.

Also removing a bit of cargo-cult from the initial evo pushbuf.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

PDISP doesn't like it when disabled CRTCs are poked.

Fixes external output not coming to life when it has cursor on.
https://bugs.freedesktop.org/show_bug.cgi?id=41608Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Otherwice code that responsible for idling the card can't work.
BIOS init tables are supposed to init the clocks to correct values,
so that shouldn't cause any problems (we don't reclock by default anyway)
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Because doing polling while hardware is disabled is a bad idea...
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Exposes the same connector properties as the Radeon implementation, however
their behaviour isn't exactly the same.  The primary difference being that
unless both hborder/vborder have been defined by the user, the driver will
keep the aspect ratio of the overscanned area the same as the mode the
display is programmed for.

Enabled for digital outputs on GeForce 8 and up, excluding GF119.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Prevents EVO getting all angry at us.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

A NV49 appeared a while back that was using the "nv41 style" pwm registers,
rather than the "nv40 style" ones my board is using.  This disproves the
previous theory that the pwm controller choice is chipset-specific.

So, after looking at a bunch of vbios images it appears that the next viable
theory is that we should select the pwm controller to use based on the gpio
line the fan is tied to, just like we do on nv50.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

The handling of the internal pwm fan controller is similar enough between
current chipsets that it makes sense to share the logic, and bugfixes :)

No hw backends converted yet, will automatically fall-through to the
"old" per-chipset fanspeed hooks for now.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Exposes the following sysfs entries:
- fan0_input: read the rotational speed of the fan (poll a bit during 250ms)
- pwm0: set the pwm duty cycle
- pwm0_min/max: set the minimum/maximum pwm value

v2 (Ben Skeggs):
- nv50 pwm controller code removed in favour of other more complete code
- FAN_RPM -> FAN_SENSE
- merged FAN_SENSE readout into common code, not at all nv50-specific
- protected fanspeed changes with perflvl_wr
- formatting tidying
- added some comments where things are shaky

v3 (Martin Peres)
- ensure duty min/max from thermal table are sane
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Martin Peres <martin.peres@ensi-bourges.fr>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

This function returns the number of planes used by a specific pixel
format.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Rob Clark <rob.clark@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Call connector->funcs->dpms(DPMS_ON) rather than just setting
connector->dpms = DPMS_ON.  This ensures that if the connector
has something to do to enable the output (rather than just using
drm_helper_connector_dpms helper directly), that this happens
at bootup.  This solves an issue with connectors not getting
enabled from fbcon_init() when the driver is loaded.
Signed-off-by: Rob Clark <rob@ti.com>
Reviewed-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

If the bpc is set from the connector is 0, we then use it later to adjust
in a special case the HDMI pixel clock, however if the bpc is 0, we end up
passing a 0 pixel clock into the code.

I'm not sure if this is the correct answer or if we should avoid the HDMI
clock adjustment for 0 values.

This fixes a divide by 0 on my Llano system with a HDMI monitor and hdmi
audio enabled.
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>