In the rare event when GFX IP suspend coincides with a s0ix entry, don't
schedule a delayed work, instead signal PMFW immediately to allow GFXOFF
entry. GFXOFF is a prerequisite for s0ix entry. PMFW needs to be
signaled about GFXOFF status before amd-pmc module passes OS HINT
to PMFW telling that everything is ready for a safe s0ix entry.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1712Signed-off-by: Lijo Lazar <lijo.lazar@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Mario Limonciello <mario.limonciell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Not sure why that was there.  Remove it.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

Memory is allocated for ttm->sg by kmalloc in kfd_mem_dmamap_userptr,
but isn't freed by kfree in kfd_mem_dmaunmap_userptr. Free it!

Fixes: 264fb4d3 ("drm/amdgpu: Add multi-GPU DMA mapping helpers")
Signed-off-by: Lang Yu <lang.yu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>

[Why]
YELLOW_CARP_B0 address was not correct

[How]
Set YELLOW_CARP_B0 to 0x1A.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Signed-off-by: Jude Shih <shenshih@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
DCN3 B0 has a mux, which redirects PHYC and PHYD to PHYF and PHYG.

[How]
Fix DIG mapping.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
(cherry picked from commit 4b7786d8)

[Why]
Starting from B0, along with RDPCSTX, RDPCSPIPE registers are also used.

[How]
Make sure RDPCSPIPE registers are programmed correctly.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
(cherry picked from commit bdd1a21b)

In commit b212921b ("elf: don't use MAP_FIXED_NOREPLACE for elf
executable mappings") we still leave MAP_FIXED_NOREPLACE in place for
load_elf_interp.

Unfortunately, this will cause kernel to fail to start with:

    1 (init): Uhuuh, elf segment at 00003ffff7ffd000 requested but the memory is mapped already
    Failed to execute /init (error -17)

The reason is that the elf interpreter (ld.so) has overlapping segments.

  readelf -l ld-2.31.so
  Program Headers:
    Type           Offset             VirtAddr           PhysAddr
                   FileSiz            MemSiz              Flags  Align
    LOAD           0x0000000000000000 0x0000000000000000 0x0000000000000000
                   0x000000000002c94c 0x000000000002c94c  R E    0x10000
    LOAD           0x000000000002dae0 0x000000000003dae0 0x000000000003dae0
                   0x00000000000021e8 0x0000000000002320  RW     0x10000
    LOAD           0x000000000002fe00 0x000000000003fe00 0x000000000003fe00
                   0x00000000000011ac 0x0000000000001328  RW     0x10000

The reason for this problem is the same as described in commit
ad55eac7 ("elf: enforce MAP_FIXED on overlaying elf segments").

Not only executable binaries, elf interpreters (e.g. ld.so) can have
overlapping elf segments, so we better drop MAP_FIXED_NOREPLACE and go
back to MAP_FIXED in load_elf_interp.

Fixes: 4ed28639 ("fs, elf: drop MAP_FIXED usage from elf_map")
Cc: <stable@vger.kernel.org> # v4.19
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: Chen Jingwen <chenjingwen6@huawei.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull ext4 fixes from Ted Ts'o:
 "Fix a number of ext4 bugs in fast_commit, inline data, and delayed
  allocation.

  Also fix error handling code paths in ext4_dx_readdir() and
  ext4_fill_super().

  Finally, avoid a grabbing a journal head in the delayed allocation
  write in the common cases where we are overwriting a pre-existing
  block or appending to an inode"

* tag 'ext4_for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: recheck buffer uptodate bit under buffer lock
  ext4: fix potential infinite loop in ext4_dx_readdir()
  ext4: flush s_error_work before journal destroy in ext4_fill_super
  ext4: fix loff_t overflow in ext4_max_bitmap_size()
  ext4: fix reserved space counter leakage
  ext4: limit the number of blocks in one ADD_RANGE TLV
  ext4: enforce buffer head state assertion in ext4_da_map_blocks
  ext4: remove extent cache entries when truncating inline data
  ext4: drop unnecessary journal handle in delalloc write
  ext4: factor out write end code of inline file
  ext4: correct the error path of ext4_write_inline_data_end()
  ext4: check and update i_disksize properly
  ext4: add error checking to ext4_ext_replay_set_iblocks()

The objtool warning that the kvm instruction emulation code triggered
wasn't very useful:

    arch/x86/kvm/emulate.o: warning: objtool: __ex_table+0x4: don't know how to handle reloc symbol type: kvm_fastop_exception

in that it helpfully tells you which symbol name it had trouble figuring
out the relocation for, but it doesn't actually say what the unknown
symbol type was that triggered it all.

In this case it was because of missing type information (type 0, aka
STT_NOTYPE), but on the whole it really should just have printed that
out as part of the message.

Because if this warning triggers, that's very much the first thing you
want to know - why did reloc2sec_off() return failure for that symbol?

So rather than just saying you can't handle some type of symbol without
saying what the type _was_, just print out the type number too.

Fixes: 24ff6525 ("objtool: Teach get_alt_entry() about more relocation types")
Link: https://lore.kernel.org/lkml/CAHk-=wiZwq-0LknKhXN4M+T8jbxn_2i9mcKpO+OaBSSq_Eh7tg@mail.gmail.com/Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recent change to make objtool aware of more symbol relocation types
(commit 24ff6525: "objtool: Teach get_alt_entry() about more
relocation types") also added another check, and resulted in this
objtool warning when building kvm on x86:

    arch/x86/kvm/emulate.o: warning: objtool: __ex_table+0x4: don't know how to handle reloc symbol type: kvm_fastop_exception

The reason seems to be that kvm_fastop_exception() is marked as a global
symbol, which causes the relocation to ke kept around for objtool.  And
at the same time, the kvm_fastop_exception definition (which is done as
an inline asm statement) doesn't actually set the type of the global,
which then makes objtool unhappy.

The minimal fix is to just not mark kvm_fastop_exception as being a
global symbol.  It's only used in that one compilation unit anyway, so
it was always pointless.  That's how all the other local exception table
labels are done.

I'm not entirely happy about the kinds of games that the kvm code plays
with doing its own exception handling, and the fact that it confused
objtool is most definitely a symptom of the code being a bit too subtle
and ad-hoc.  But at least this trivial one-liner makes objtool no longer
upset about what is going on.

Fixes: 24ff6525 ("objtool: Teach get_alt_entry() about more relocation types")
Link: https://lore.kernel.org/lkml/CAHk-=wiZwq-0LknKhXN4M+T8jbxn_2i9mcKpO+OaBSSq_Eh7tg@mail.gmail.com/
Cc: Borislav Petkov <bp@suse.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Wanpeng Li <wanpengli@tencent.com>
Cc: Jim Mattson <jmattson@google.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull char/misc driver fixes from Greg KH:
 "Here are some small misc driver fixes for 5.15-rc4. They are in two
  "groups":

   - ipack driver fixes for issues found by Johan Hovold

   - interconnect driver fixes for reported problems

  All of these have been in linux-next for a while with no reported
  issues"

* tag 'char-misc-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  ipack: ipoctal: fix module reference leak
  ipack: ipoctal: fix missing allocation-failure check
  ipack: ipoctal: fix tty-registration error handling
  ipack: ipoctal: fix tty registration race
  ipack: ipoctal: fix stack information leak
  interconnect: qcom: sdm660: Add missing a2noc qos clocks
  dt-bindings: interconnect: sdm660: Add missing a2noc qos clocks
  interconnect: qcom: sdm660: Correct NOC_QOS_PRIORITY shift and mask
  interconnect: qcom: sdm660: Fix id of slv_cnoc_mnoc_cfg

Merge tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core fixes from Greg KH:
 "Here are some driver core and kernfs fixes for reported issues for
  5.15-rc4. These fixes include:

   - kernfs positive dentry bugfix

   - debugfs_create_file_size error path fix

   - cpumask sysfs file bugfix to preserve the user/kernel abi (has been
     reported multiple times.)

   - devlink fixes for mdiobus devices as reported by the subsystem
     maintainers.

  Also included in here are some devlink debugging changes to make it
  easier for people to report problems when asked. They have already
  helped with the mdiobus and other subsystems reporting issues.

  All of these have been linux-next for a while with no reported issues"

* tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  kernfs: also call kernfs_set_rev() for positive dentry
  driver core: Add debug logs when fwnode links are added/deleted
  driver core: Create __fwnode_link_del() helper function
  driver core: Set deferred probe reason when deferred by driver core
  net: mdiobus: Set FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for mdiobus parents
  driver core: fw_devlink: Add support for FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD
  driver core: fw_devlink: Improve handling of cyclic dependencies
  cpumask: Omit terminating null byte in cpumap_print_{list,bitmask}_to_buf
  debugfs: debugfs_create_file_size(): use IS_ERR to check for error

Pull scheduler fixes from Borislav Petkov:

 - Tell the compiler to always inline is_percpu_thread()

 - Make sure tunable_scaling buffer is null-terminated after an update
   in sysfs

 - Fix LTP named regression due to cgroup list ordering

* tag 'sched_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched: Always inline is_percpu_thread()
  sched/fair: Null terminate buffer when updating tunable_scaling
  sched/fair: Add ancestors of unthrottled undecayed cfs_rq

Pull perf fixes from Borislav Petkov:

 - Make sure the destroy callback is reset when a event initialization
   fails

 - Update the event constraints for Icelake

 - Make sure the active time of an event is updated even for inactive
   events

* tag 'perf_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: fix userpage->time_enabled of inactive events
  perf/x86/intel: Update event constraints for ICX
  perf/x86: Reset destroy callback on event init failure

Pull objtool fix from Borislav Petkov:

 - Handle symbol relocations properly due to changes in the toolchains
   which remove section symbols now

* tag 'objtool_urgent_for_v5.15_rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  objtool: Teach get_alt_entry() about more relocation types

Merge tag 'hwmon-for-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:

 - Fixed various potential NULL pointer accesses in w8379* drivers

 - Improved error handling, fault reporting, and fixed rounding in
   thmp421 driver

 - Fixed error handling in ltc2947 driver

 - Added missing attribute to pmbus/mp2975 driver

 - Fixed attribute values in pbus/ibm-cffps, occ, and mlxreg-fan
   drivers

 - Removed unused residual code from k10temp driver

* tag 'hwmon-for-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (w83793) Fix NULL pointer dereference by removing unnecessary structure field
  hwmon: (w83792d) Fix NULL pointer dereference by removing unnecessary structure field
  hwmon: (w83791d) Fix NULL pointer dereference by removing unnecessary structure field
  hwmon: (pmbus/mp2975) Add missed POUT attribute for page 1 mp2975 controller
  hwmon: (pmbus/ibm-cffps) max_power_out swap changes
  hwmon: (occ) Fix P10 VRM temp sensors
  hwmon: (ltc2947) Properly handle errors when looking for the external clock
  hwmon: (tmp421) fix rounding for negative values
  hwmon: (tmp421) report /PVLD condition as fault
  hwmon: (tmp421) handle I2C errors
  hwmon: (mlxreg-fan) Return non-zero value when fan current state is enforced from sysfs
  hwmon: (k10temp) Remove residues of current and voltage

Pull ksmbd server fixes from Steve French:
 "Eleven fixes for the ksmbd kernel server, mostly security related:

   - an important fix for disabling weak NTLMv1 authentication

   - seven security (improved buffer overflow checks) fixes

   - fix for wrong infolevel struct used in some getattr/setattr paths

   - two small documentation fixes"

* tag '5.15-rc3-ksmbd-fixes' of git://git.samba.org/ksmbd:
  ksmbd: missing check for NULL in convert_to_nt_pathname()
  ksmbd: fix transform header validation
  ksmbd: add buffer validation for SMB2_CREATE_CONTEXT
  ksmbd: add validation in smb2 negotiate
  ksmbd: add request buffer validation in smb2_set_info
  ksmbd: use correct basic info level in set_file_basic_info()
  ksmbd: remove NTLMv1 authentication
  ksmbd: fix documentation for 2 functions
  MAINTAINERS: rename cifs_common to smbfs_common in cifs and ksmbd entry
  ksmbd: fix invalid request buffer access in compound
  ksmbd: remove RFC1002 check in smb2 request

Pull SCSI fixes from James Bottomley:
 "Five fairly minor fixes and spelling updates, all in drivers. Even
  though the ufs fix is in tracing, it's a potentially exploitable use
  beyond end of array bug"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: csiostor: Add module softdep on cxgb4
  scsi: qla2xxx: Fix excessive messages during device logout
  scsi: virtio_scsi: Fix spelling mistake "Unsupport" -> "Unsupported"
  scsi: ses: Fix unsigned comparison with less than zero
  scsi: ufs: Fix illegal offset in UPIU event trace

Pull block fixes from Jens Axboe:
 "A few block fixes for this release:

   - Revert a BFQ commit that causes breakage for people. Unfortunately
     it was auto-selected for stable as well, so now 5.14.7 suffers from
     it too. Hopefully stable will pick up this revert quickly too, so
     we can remove the issue on that end as well.

   - Add a quirk for Apple NVMe controllers, which due to their
     non-compliance broke due to the introduction of command sequences
     (Keith)

   - Use shifts in nbd, fixing a __divdi3 issue (Nick)"

* tag 'block-5.15-2021-10-01' of git://git.kernel.dk/linux-block:
  nbd: use shifts rather than multiplies
  Revert "block, bfq: honor already-setup queue merges"
  nvme: add command id quirk for apple controllers

Pull io_uring fixes from Jens Axboe:
 "Two fixes in here:

   - The signal issue that was discussed start of this week (me).

   - Kill dead fasync support in io_uring. Looks like it was broken
     since io_uring was initially merged, and given that nobody has ever
     complained about it, let's just kill it (Pavel)"

* tag 'io_uring-5.15-2021-10-01' of git://git.kernel.dk/linux-block:
  io_uring: kill fasync
  io-wq: exclusively gate signal based exit on get_signal() return

Pull libnvdimm fixes from Dan Williams:
 "A fix for a regression added this cycle in the pmem driver, and for a
  long standing bug for failed NUMA node lookups on ARM64.

  This has appeared in -next for several days with no reported issues.

  Summary:

   - Fix a regression that caused the sysfs ABI for pmem block devices
     to not be registered. This fails the nvdimm unit tests and dax
     xfstests.

   - Fix numa node lookups for dax-kmem memory (device-dax memory
     assigned to the page allocator) on ARM64"

* tag 'libnvdimm-fixes-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
  nvdimm/pmem: fix creating the dax group
  ACPI: NFIT: Use fallback node id when numa info in NFIT table is incorrect

In cachefiles_mark_object_buried, the dentry in question may not have an
owner, and thus our cachefiles_object pointer may be NULL when calling
the tracepoint, in which case we will also not have a valid debug_id to
print in the tracepoint.

Check for NULL object in the tracepoint and if so, just set debug_id to
MAX_UINT as was done in 2908f5e1 ("fscache: Add a cookie debug ID
and use that in traces").

This fixes the following oops:

    FS-Cache: Cache "mycache" added (type cachefiles)
    CacheFiles: File cache on vdc registered
    ...
    Workqueue: fscache_object fscache_object_work_func [fscache]
    RIP: 0010:trace_event_raw_event_cachefiles_mark_buried+0x4e/0xa0 [cachefiles]
    ....
    Call Trace:
     cachefiles_mark_object_buried+0xa5/0xb0 [cachefiles]
     cachefiles_bury_object+0x270/0x430 [cachefiles]
     cachefiles_walk_to_object+0x195/0x9c0 [cachefiles]
     cachefiles_lookup_object+0x5a/0xc0 [cachefiles]
     fscache_look_up_object+0xd7/0x160 [fscache]
     fscache_object_work_func+0xb2/0x340 [fscache]
     process_one_work+0x1f1/0x390
     worker_thread+0x53/0x3e0
     kthread+0x127/0x150

Fixes: 2908f5e1 ("fscache: Add a cookie debug ID and use that in traces")
Signed-off-by: Dave Wysochanski <dwysocha@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-cachefs@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

5.15-rc1 crashes with blank screen when booting up on two ThinkPads
using i915.  Bisections converge convincingly, but arrive at different
and suprising "culprits", none of them the actual culprit.

netconsole (with init_netconsole() hacked to call i915_init() when
logging has started, instead of by module_init()) tells the story:

kernel BUG at drivers/gpu/drm/i915/i915_sw_fence.c:245!
with RSI: ffffffff814d408b pointing to sw_fence_dummy_notify().
I've been building with CONFIG_CC_OPTIMIZE_FOR_SIZE=y, and that
function needs to be 4-byte aligned.

Fixes: 62eaf0ae ("drm/i915/guc: Support request cancellation")
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If driver read tmp value sufficient for
(tmp & 0x08) && (!(tmp & 0x80)) && ((tmp & 0x7) == ((tmp >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().

The patch fixes possible NULL pointer dereference by removing lm75[].

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-3-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignments]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().

The patch fixes possible NULL pointer dereference by removing lm75[].

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-2-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multipline alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

If driver read val value sufficient for
(val & 0x08) && (!(val & 0x80)) && ((val & 0x7) == ((val >> 4) & 0x7))
from device then Null pointer dereference occurs.
(It is possible if tmp = 0b0xyz1xyz, where same literals mean same numbers)
Also lm75[] does not serve a purpose anymore after switching to
devm_i2c_new_dummy_device() in w83791d_detect_subclients().

The patch fixes possible NULL pointer dereference by removing lm75[].

Found by Linux Driver Verification project (linuxtesting.org).

Cc: stable@vger.kernel.org
Signed-off-by: Nadezda Lutovinova <lutovinova@ispras.ru>
Link: https://lore.kernel.org/r/20210921155153.28098-1-lutovinova@ispras.ru
[groeck: Dropped unnecessary continuation lines, fixed multi-line alignment]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Add missed attribute for reading POUT from page 1.
It is supported by device, but has been missed in initial commit.

Fixes: 2c6fcbb2 ("hwmon: (pmbus) Add support for MPS Multi-phase mp2975 controller")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Link: https://lore.kernel.org/r/20210927070740.2149290-1-vadimp@nvidia.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

The bytes for max_power_out from the ibm-cffps devices differ in byte
order for some power supplies.

The Witherspoon power supply returns the bytes in MSB/LSB order.

The Rainier power supply returns the bytes in LSB/MSB order.

The Witherspoon power supply uses version cffps1. The Rainier power
supply should use version cffps2. If version is cffps1, swap the bytes
before output to max_power_out.

Tested:
    Witherspoon before: 3148. Witherspoon after: 3148.
    Rainier before: 53255. Rainier after: 2000.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210928205051.1222815-1-bjwyman@gmail.com
[groeck: Replaced yoda programming]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>

The P10 (temp sensor version 0x10) doesn't do the same VRM status
reporting that was used on P9. It just reports the temperature, so
drop the check for VRM fru type in the sysfs show function, and don't
set the name to "alarm".

Fixes: db4919ec ("hwmon: (occ) Add new temperature sensor type")
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210929153604.14968-1-eajames@linux.ibm.comSigned-off-by: Guenter Roeck <linux@roeck-us.net>

Pull s390 fix from Vasily Gorbik:
 "One fix for 5.15-rc4: Avoid CIO excessive path-verification requests,
  which might cause unwanted delays"

* tag 's390-5.15-4' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  s390/cio: avoid excessive path-verification requests

Because Rui is now going to focus on work that is not related to the
maintenance of the thermal subsystem in the kernel, Rafael will start
to help Daniel with handling the development process as a new member
of the thermal maintainers team.  Rui will continue to review patches
in that area.

The thermal development process flow will change so that the material
from the thermal git tree will be merged into the thermal branch of
the linux-pm.git tree before going into the mainline.

Update the information in MAINTAINERS accordingly.
Signed-off-by: Rafael J. Wysocki <rafael@kernel.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull more kvm fixes from Paolo Bonzini:
 "Small x86 fixes"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: selftests: Ensure all migrations are performed when test is affined
  KVM: x86: Swap order of CPUID entry "index" vs. "significant flag" checks
  ptp: Fix ptp_kvm_getcrosststamp issue for x86 ptp_kvm
  x86/kvmclock: Move this_cpu_pvti into kvmclock.h
  selftests: KVM: Don't clobber XMM register when read
  KVM: VMX: Fix a TSX_CTRL_CPUID_CLEAR field mask issue

Pull drm fixes from Daniel Vetter:
 "Dave is out on a long w/e, should be back next week.

  Nothing nefarious, just a bunch of driver fixes: amdgpu, i915, tegra,
  and one exynos driver fix"

* tag 'drm-fixes-2021-10-01' of git://anongit.freedesktop.org/drm/drm:
  drm/amdgpu: force exit gfxoff on sdma resume for rmb s0ix
  drm/amdgpu: check tiling flags when creating FB on GFX8-
  drm/amd/display: Pass PCI deviceid into DC
  drm/amd/display: initialize backlight_ramping_override to false
  drm/amdgpu: correct initial cp_hqd_quantum for gfx9
  drm/amd/display: Fix Display Flicker on embedded panels
  drm/amdgpu: fix gart.bo pin_count leak
  drm/i915: Remove warning from the rps worker
  drm/i915/request: fix early tracepoints
  drm/i915/guc, docs: Fix pdfdocs build error by removing nested grid
  gpu: host1x: Plug potential memory leak
  gpu/host1x: fence: Make spinlock static
  drm/tegra: uapi: Fix wrong mapping end address in case of disabled IOMMU
  drm/tegra: dc: Remove unused variables
  drm/exynos: Make use of the helper function devm_platform_ioremap_resource()
  drm/i915/gvt: fix the usage of ww lock in gvt scheduler.

We have never supported fasync properly, it would only fire when there
is something polling io_uring making it useless. The original support came
in through the initial io_uring merge for 5.1. Since it's broken and
nobody has reported it, get rid of the fasync bits.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Link: https://lore.kernel.org/r/2f7ca3d344d406d34fa6713824198915c41cea86.1633080236.git.asml.silence@gmail.comSigned-off-by: Jens Axboe <axboe@kernel.dk>

Pull iommu fixes from Joerg Roedel:

 - Two fixes for the new Apple DART driver to fix a kernel panic and a
   stale data usage issue

 - Intel VT-d fix for how PCI device ids are printed

* tag 'iommu-fixes-v5.15-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
  iommu/dart: Clear sid2group entry when a group is freed
  iommu/vt-d: Drop "0x" prefix from PCI bus & device addresses
  iommu/dart: Remove iommu_flush_ops

Merge tag 'exynos-drm-fixes-for-v5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-fixes

One cleanup
- Use devm_platform_ioremap_resource() helper function instead of old
one.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210928074158.2942-1-inki.dae@samsung.com

Merge tag 'amd-drm-fixes-5.15-2021-09-29' of https://gitlab.freedesktop.org/agd5f/linux into drm-fixes

amd-drm-fixes-5.15-2021-09-29:

amdgpu:
- gart pin count fix
- eDP flicker fix
- GFX9 MQD fix
- Display fixes
- Tiling flags fix for pre-GFX9
- SDMA resume fix for S0ix
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210930023013.5207-1-alexander.deucher@amd.com

Merge tag 'drm-intel-fixes-2021-09-30' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes

drm/i915 fixes for v5.15-rc4:
- Fix GVT scheduler ww lock usage
- Fix pdfdocs documentation build
- Fix request early tracepoints
- Fix an invalid warning from rps worker
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87lf3ev44z.fsf@intel.com

  vmlinux.o: warning: objtool: check_preemption_disabled()+0x81: call to is_percpu_thread() leaves .noinstr.text section
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20210928084218.063371959@infradead.org