- 27 Jun, 2022 3 commits
-
-
Jeff LaBundy authored
Select variants of silicon silently mirror part of the event mask register to the system setup register (0xD0), and vice versa. For the following sequence: 1. Read registers 0xD0 onward and store their contents. 2. Modify the contents, including event mask fields. 3. Write registers 0xD0 onward with the modified contents. 4. Write register 0xD0 on its own again later, using the contents from step 1 to populate any reserved fields. ...the event mask register (e.g. address 0xDA) has been corrupted by writing register 0xD0 with contents that were made stale after step 3. To solve this problem, read register 0xD0 once more between steps 3 and 4. When register 0xD0 is written during step 4, the portion which is mirrored to the event mask register already matches what was written in step 3. Fixes: e505edae ("Input: add support for Azoteq IQS7222A/B/C") Signed-off-by:
Jeff LaBundy <jeff@labundy.com> Link: https://lore.kernel.org/r/20220626072412.475211-4-jeff@labundy.comSigned-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com>
-
Jeff LaBundy authored
The release cycle of any key mapped to a slider gesture relies upon trailing interrupts generated by other unmasked sources, the timing and presence of which are inconsistent. To solve this problem, explicitly report a release cycle to emulate a full keystroke. Also, unmask touch interrupts if the slider press event is defined; this ensures the device reports a final interrupt with coordinate = 0xFFFF once the finger is lifted. As a result of how the logic has been refactored, the press/release event can now be mapped to a GPIO. This is more convenient than the previous solution, which required each channel within the slider to specify the same GPIO. As part of this change, use the device's resolution rather than its number of interrupt status registers to more safely determine if it is capable of reporting gestures. Last but not least, make the code a bit simpler by eliminating some unnecessarily complex conditional statements and a macro that could be derived using information that is already available. Fixes: e505edae ("Input: add support for Azoteq IQS7222A/B/C") Signed-off-by:
-
Jeff LaBundy authored
If a positive swipe/flick gesture is defined but the corresponding negative gesture is not, the former is inadvertently disabled. Fix this by gently refactoring the logic responsible for disabling all gestures by default. As part of this change, make the code a bit simpler by eliminating a superfluous conditional check. If a slider event does not define an enable control, the second term of the bitwise AND operation is simply 0xFFFF. Fixes: e505edae ("Input: add support for Azoteq IQS7222A/B/C") Signed-off-by:
-
- 22 Jun, 2022 2 commits
-
-
Jiang Jian authored
Consider * alignment in comments Signed-off-by:
Jiang Jian <jiangjian@cdjrlc.com> Link: https://lore.kernel.org/r/20220621070032.30072-1-jiangjian@cdjrlc.comSigned-off-by:
-
Jiang Jian authored
Drop a redundant word 'the' in the comments of function gpio_mouse_scan. Signed-off-by:
-
- 01 Jun, 2022 4 commits
-
-
AngeloGioacchino Del Regno authored
As the second and last step of preparation to add support for more PMICs in this driver, move the long press debounce mask to struct mtk_pmic_regs and use that in mtk_pmic_keys_lp_reset_setup() instead of directly using the definition. While at it, remove the definition for MTK_PMIC_RST_DU_SHIFT as we are able to calculate it dynamically and spares us some unnecessary new definitions around for future per-PMIC variations of RST_DU_MASK. Lastly, it was necessary to change the function signature of mtk_pmic_keys_lp_reset_setup() to now pass a pointer to the main mtk_pmic_regs structure, since that's where the reset debounce mask now resides. This commit brings no functional changes. Signed-off-by:
AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by:
Mattijs Korpershoek <mkorpershoek@baylibre.com> Link: https://lore.kernel.org/r/20220524093505.85438-3-angelogioacchino.delregno@collabora.comSigned-off-by:
-
AngeloGioacchino Del Regno authored
Place the key bit in struct mtk_pmic_keys_regs to enhance this driver's flexibility, in preparation for adding support for more PMICs. While at it, remove the definition of MTK_PMIC_RST_KEY_MASK as we are now dynamically setting the keymask relatively to the keys that are defined in the newly added rst_en_mask variable, on a per-key basis. This commit brings no functional changes. Signed-off-by:
-
Dmitry Torokhov authored
Instead of doing 3 read-modify-write operations when configuring behavior of long-press, consolidate everything into one. Reviewed-by:
-
Dmitry Torokhov authored
There are no hard architecture dependencies in the driver, so to improve compile test coverage let's enable the driver when COMPILE_TEST is selected. Reviewed-by:
-
- 31 May, 2022 4 commits
-
-
Dmitry Torokhov authored
I2C core will set up device as a wakeup source and will configure interrupt as a wakeup interrupt if client is created with I2C_CLIENT_WAKE flag. Let's rely on this facility and to not unconditionally set up the device as wakeup device in the driver. Acked-by:
Michael Hennerich <michael.hennerich@analog.com> Link: https://lore.kernel.org/r/20220528045631.289821-4-dmitry.torokhov@gmail.comSigned-off-by:
-
Dmitry Torokhov authored
This simplifies error handling in probe() and reduces amount of explicit code in remove(). Acked-by:
-
Dmitry Torokhov authored
Instead of using hard interrupt handler and manually scheduling work item to handle I2C communications, let's switch to threaded interrupt handling. While at that enforce the readout delay required on pre- revision 4 silicon. Acked-by:
-
Dmitry Torokhov authored
To improve compile-time coverage let's drop #ifdef CONFIG_PM guards and use SIMPLE_DEV_PM_OPS and __maybe_unused attributes and rely on the linker to drop unused code. Acked-by:
-
- 28 May, 2022 5 commits
-
-
Furquan Shaikh authored
Some detachable/convertible x86 Chromebooks use EC buttons/switches interface to signal volume up/down and other buttons. This configuration is signalled via presence of GOOG0007 ACPI device. The main keyboard on such Chromebooks is still using the standard 8042/atkbd combo. Signed-off-by:
Furquan Shaikh <furquan@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20220526231230.2805147-2-dmitry.torokhov@gmail.comSigned-off-by:
-
Dmitry Torokhov authored
In preparation to enabling this driver on x86 devices let's switch from OF-specific property API to the generic one. Reviewed-by:
-
Linus Walleij authored
The defines are sometimes named BT541_* and sometimes ZINITIX_*, name them all ZINITIX_* because they certainly apply to a lot more touchscreens than the BT541. Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Link: https://lore.kernel.org/r/20220410120059.2583849-3-linus.walleij@linaro.orgSigned-off-by:
-
Krzysztof Kozlowski authored
Devicetree specification expects nodes to have generic names, if possible, so replace custom ones with something generic. For gpio-keys, the more popular format is "key-xxx" instead of "xxx-key", so choose the first one. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Acked-by:
Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20220524093136.7980-1-krzysztof.kozlowski@linaro.orgSigned-off-by:
-
Minghao Chi authored
Use pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Link: https://lore.kernel.org/r/20220414085710.2541867-1-chi.minghao@zte.com.cnSigned-off-by:
-
- 27 May, 2022 1 commit
-
-
Dmitry Torokhov authored
Sync up with mainline to get updates to OMAP4 keypad driver and other upstream goodies.
-
- 26 May, 2022 2 commits
-
-
Dmitry Torokhov authored
The commit 26623eea attempted to deal with potential leak of runtime PM counter when opening the touchscreen device, however it ended up erroneously dropping the counter in the case of successfully enabling the device. Let's address this by using pm_runtime_resume_and_get() and then executing pm_runtime_put_sync() only when we fail to send "sense on" command to the device. Fixes: 26623eea ("Input: stmfts - fix reference leak in stmfts_input_open") Reported-by:
Pavel Machek <pavel@denx.de> Signed-off-by:
-
Lad Prabhakar authored
gpio_keys module can either accept gpios or interrupts. The module initializes delayed work in case of gpios only and is only used if debounce timer is not used, so make sure cancel_delayed_work_sync() is called only when its gpio-backed and debounce_use_hrtimer is false. This fixes the issue seen below when the gpio_keys module is unloaded and an interrupt pin is used instead of GPIO: [ 360.297569] ------------[ cut here ]------------ [ 360.302303] WARNING: CPU: 0 PID: 237 at kernel/workqueue.c:3066 __flush_work+0x414/0x470 [ 360.310531] Modules linked in: gpio_keys(-) [ 360.314797] CPU: 0 PID: 237 Comm: rmmod Not tainted 5.18.0-rc5-arm64-renesas-00116-g73636105874d-dirty #166 [ 360.324662] Hardware name: Renesas SMARC EVK based on r9a07g054l2 (DT) [ 360.331270] pstate: 60400005 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 360.338318] pc : __flush_work+0x414/0x470 [ 360.342385] lr : __cancel_work_timer+0x140/0x1b0 [ 360.347065] sp : ffff80000a7fba00 [ 360.350423] x29: ffff80000a7fba00 x28: ffff000012b9c5c0 x27: 0000000000000000 [ 360.357664] x26: ffff80000a7fbb80 x25: ffff80000954d0a8 x24: 0000000000000001 [ 360.364904] x23: ffff800009757000 x22: 0000000000000000 x21: ffff80000919b000 [ 360.372143] x20: ffff00000f5974e0 x19: ffff00000f5974e0 x18: ffff8000097fcf48 [ 360.379382] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000053f40 [ 360.386622] x14: ffff800009850e88 x13: 0000000000000002 x12: 000000000000a60c [ 360.393861] x11: 000000000000a610 x10: 0000000000000000 x9 : 0000000000000008 [ 360.401100] x8 : 0101010101010101 x7 : 00000000a473c394 x6 : 0080808080808080 [ 360.408339] x5 : 0000000000000001 x4 : 0000000000000000 x3 : ffff80000919b458 [ 360.415578] x2 : ffff8000097577f0 x1 : 0000000000000001 x0 : 0000000000000000 [ 360.422818] Call trace: [ 360.425299] __flush_work+0x414/0x470 [ 360.429012] __cancel_work_timer+0x140/0x1b0 [ 360.433340] cancel_delayed_work_sync+0x10/0x18 [ 360.437931] gpio_keys_quiesce_key+0x28/0x58 [gpio_keys] [ 360.443327] devm_action_release+0x10/0x18 [ 360.447481] release_nodes+0x8c/0x1a0 [ 360.451194] devres_release_all+0x90/0x100 [ 360.455346] device_unbind_cleanup+0x14/0x60 [ 360.459677] device_release_driver_internal+0xe8/0x168 [ 360.464883] driver_detach+0x4c/0x90 [ 360.468509] bus_remove_driver+0x54/0xb0 [ 360.472485] driver_unregister+0x2c/0x58 [ 360.476462] platform_driver_unregister+0x10/0x18 [ 360.481230] gpio_keys_exit+0x14/0x828 [gpio_keys] [ 360.486088] __arm64_sys_delete_module+0x1e0/0x270 [ 360.490945] invoke_syscall+0x40/0xf8 [ 360.494661] el0_svc_common.constprop.3+0xf0/0x110 [ 360.499515] do_el0_svc+0x20/0x78 [ 360.502877] el0_svc+0x48/0xf8 [ 360.505977] el0t_64_sync_handler+0x88/0xb0 [ 360.510216] el0t_64_sync+0x148/0x14c [ 360.513930] irq event stamp: 4306 [ 360.517288] hardirqs last enabled at (4305): [<ffff8000080b0300>] __cancel_work_timer+0x130/0x1b0 [ 360.526359] hardirqs last disabled at (4306): [<ffff800008d194fc>] el1_dbg+0x24/0x88 [ 360.534204] softirqs last enabled at (4278): [<ffff8000080104a0>] _stext+0x4a0/0x5e0 [ 360.542133] softirqs last disabled at (4267): [<ffff8000080932ac>] irq_exit_rcu+0x18c/0x1b0 [ 360.550591] ---[ end trace 0000000000000000 ]--- Signed-off-by:
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> Link: https://lore.kernel.org/r/20220524135822.14764-1-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by:
-
- 22 May, 2022 4 commits
-
-
Linus Torvalds authored
-
David Howells authored
If a callback break occurs (change notification), afs_getattr() needs to issue an FS.FetchStatus RPC operation to update the status of the file being examined by the stat-family of system calls. Fix afs_getattr() to do this if AFS_VNODE_CB_PROMISED has been cleared on a vnode by a callback break. Skip this if AT_STATX_DONT_SYNC is set. This can be tested by appending to a file on one AFS client and then using "stat -L" to examine its length on a machine running kafs. This can also be watched through tracing on the kafs machine. The callback break is seen: kworker/1:1-46 [001] ..... 978.910812: afs_cb_call: c=0000005f YFSCB.CallBack kworker/1:1-46 [001] ...1. 978.910829: afs_cb_break: 100058:23b4c:242d2c2 b=2 s=1 break-cb kworker/1:1-46 [001] ..... 978.911062: afs_call_done: c=0000005f ret=0 ab=0 [0000000082994ead] And then the stat command generated no traffic if unpatched, but with this change a call to fetch the status can be observed: stat-4471 [000] ..... 986.744122: afs_make_fs_call: c=000000ab 100058:023b4c:242d2c2 YFS.FetchStatus stat-4471 [000] ..... 986.745578: afs_call_done: c=000000ab ret=0 ab=0 [0000000087fc8c84] Fixes: 08e0e7c8 ("[AF_RXRPC]: Make the in-kernel AFS filesystem use AF_RXRPC.") Reported-by:Markus Suvanto <markus.suvanto@gmail.com> Signed-off-by:
David Howells <dhowells@redhat.com> cc: Marc Dionne <marc.dionne@auristor.com> cc: linux-afs@lists.infradead.org Tested-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds authored
Pull i2c fixes from Wolfram Sang: "Some I2C driver bugfixes for 5.18. Nothing spectacular but worth fixing" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: drivers: i2c: thunderx: Allow driver to work with ACPI defined TWSI controllers i2c: ismt: Provide a DMA buffer for Interrupt Cause Logging i2c: mt7621: fix missing clk_disable_unprepare() on error in mtk_i2c_probe()
-
Linus Torvalds authored
Merge tag 'perf-tools-fixes-for-v5.18-2022-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux Pull perf tools fixes from Arnaldo Carvalho de Melo: - Fix and validate CPU map inputs in synthetic PERF_RECORD_STAT events in 'perf stat'. - Fix x86's arch__intr_reg_mask() for the hybrid platform. - Address 'perf bench numa' compiler error on s390. - Fix check for btf__load_from_kernel_by_id() in libbpf. - Fix "all PMU test" 'perf test' to skip hv_24x7/hv_gpci tests on powerpc. - Fix session topology test to skip the test in guest environment. - Skip BPF 'perf test' if clang is not present. - Avoid shell test description infinite loop in 'perf test'. - Fix Intel LBR callstack entries and nr print message. * tag 'perf-tools-fixes-for-v5.18-2022-05-21' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux: perf session: Fix Intel LBR callstack entries and nr print message perf test bpf: Skip test if clang is not present perf test session topology: Fix test to skip the test in guest environment perf bench numa: Address compiler error on s390 perf test: Avoid shell test description infinite loop perf regs x86: Fix arch__intr_reg_mask() for the hybrid platform perf test: Fix "all PMU test" to skip hv_24x7/hv_gpci tests on powerpc perf stat: Fix and validate CPU map inputs in synthetic PERF_RECORD_STAT events perf build: Fix check for btf__load_from_kernel_by_id() in libbpf
-
- 21 May, 2022 15 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/inputLinus Torvalds authored
Pull input fixes from Dmitry Torokhov: "A small fixup to ili210x touchscreen driver, and updated maintainer entry for the device tree binding of Mediatek 6779 keypad: - fix reset timing of Ilitek touchscreens - update maintainer entry of DT binding of Mediatek 6779 keypad" * tag 'input-for-v5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: ili210x - use one common reset implementation Input: ili210x - fix reset timing dt-bindings: input: mediatek,mt6779-keypad: update maintainer
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsiLinus Torvalds authored
Pull SCSI fixes from James Bottomley: "Two patches, both in drivers. The iscsi one is fixing the cpumask issue you commented on and the ufs one is a late arriving fix for conditions that can occur in Host Performance Booster reads" * tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: scsi: ufs: core: Fix referencing invalid rsp field scsi: target: Fix incorrect use of cpumask_t
-
Julia Lawall authored
Spelling mistake (triple letters) in comment. Detected with the help of Coccinelle. Signed-off-by:
Julia Lawall <Julia.Lawall@inria.fr> Link: https://lore.kernel.org/r/20220521111145.81697-27-Julia.Lawall@inria.frSigned-off-by:
-
Chengdong Li authored
When generating callstack information from branch_stack(Intel LBR), the actual number of callstack entry should be bigger than the number of branch_stack, for example: branch_stack records: B() -> C() A() -> B() converted callstack records should be: C() B() A() though, the number of callstack equals to the number of branch stack plus 1. This patch fixes above issue in branch_stack__printf(). For example, # echo 'scale=2000; 4*a(1)' > cmd # perf record --call-graph lbr bc -l < cmd Before applying this patch, `perf script -D` output: 1220022677386876 0x2a40 [0xd8]: PERF_RECORD_SAMPLE(IP, 0x4002): 17990/17990: 0x40a6d6 period: 894172 addr: 0 ... LBR call chain: nr:8 ..... 0: fffffffffffffe00 ..... 1: 000000000040a410 ..... 2: 000000000040573c ..... 3: 0000000000408650 ..... 4: 00000000004022f2 ..... 5: 00000000004015f5 ..... 6: 00007f5ed6dcb553 ..... 7: 0000000000401698 ... FP chain: nr:2 ..... 0: fffffffffffffe00 ..... 1: 000000000040a6d8 ... branch callstack: nr:6 # which is not consistent with LBR records. ..... 0: 000000000040a410 ..... 1: 0000000000408650 # ditto ..... 2: 00000000004022f2 ..... 3: 00000000004015f5 ..... 4: 00007f5ed6dcb553 ..... 5: 0000000000401698 ... thread: bc:17990 ...... dso: /usr/bin/bc bc 17990 1220022.677386: 894172 cycles: 40a410 [unknown] (/usr/bin/bc) 40573c [unknown] (/usr/bin/bc) 408650 [unknown] (/usr/bin/bc) 4022f2 [unknown] (/usr/bin/bc) 4015f5 [unknown] (/usr/bin/bc) 7f5ed6dcb553 __libc_start_main+0xf3 (/usr/lib64/libc-2.17.so) 401698 [unknown] (/usr/bin/bc) After applied: 1220022677386876 0x2a40 [0xd8]: PERF_RECORD_SAMPLE(IP, 0x4002): 17990/17990: 0x40a6d6 period: 894172 addr: 0 ... LBR call chain: nr:8 ..... 0: fffffffffffffe00 ..... 1: 000000000040a410 ..... 2: 000000000040573c ..... 3: 0000000000408650 ..... 4: 00000000004022f2 ..... 5: 00000000004015f5 ..... 6: 00007f5ed6dcb553 ..... 7: 0000000000401698 ... FP chain: nr:2 ..... 0: fffffffffffffe00 ..... 1: 000000000040a6d8 ... branch callstack: nr:7 ..... 0: 000000000040a410 ..... 1: 000000000040573c ..... 2: 0000000000408650 ..... 3: 00000000004022f2 ..... 4: 00000000004015f5 ..... 5: 00007f5ed6dcb553 ..... 6: 0000000000401698 ... thread: bc:17990 ...... dso: /usr/bin/bc bc 17990 1220022.677386: 894172 cycles: 40a410 [unknown] (/usr/bin/bc) 40573c [unknown] (/usr/bin/bc) 408650 [unknown] (/usr/bin/bc) 4022f2 [unknown] (/usr/bin/bc) 4015f5 [unknown] (/usr/bin/bc) 7f5ed6dcb553 __libc_start_main+0xf3 (/usr/lib64/libc-2.17.so) 401698 [unknown] (/usr/bin/bc) Change from v1: - refined code style according to Jiri's review comments. Signed-off-by:
Chengdong Li <chengdongli@tencent.com> Acked-by:
Namhyung Kim <namhyung@kernel.org> Cc: Adrian Hunter <adrian.hunter@intel.com> Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com> Cc: Alexey Bayduraev <alexey.v.bayduraev@linux.intel.com> Cc: Andi Kleen <ak@linux.intel.com> Cc: German Gomez <german.gomez@arm.com> Cc: Ian Rogers <irogers@google.com> Cc: Ingo Molnar <mingo@redhat.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Riccardo Mancini <rickyman7@gmail.com> Cc: likexu@tencent.com Link: https://lore.kernel.org/r/20220517015726.96131-1-chengdongli@tencent.comSigned-off-by:
Arnaldo Carvalho de Melo <acme@redhat.com>
-
Athira Rajeev authored
Perf BPF filter test fails in environment where "clang" is not installed. Test failure logs: <<>> 42: BPF filter : 42.1: Basic BPF filtering : Skip 42.2: BPF pinning : FAILED! 42.3: BPF prologue generation : FAILED! <<>> Enabling verbose option provided debug logs which says clang/llvm needs to be installed. Snippet of verbose logs: <<>> 42.2: BPF pinning : --- start --- test child forked, pid 61423 ERROR: unable to find clang. Hint: Try to install latest clang/llvm to support BPF. Check your $PATH <<logs_here>> Failed to compile test case: 'Basic BPF llvm compile' Unable to get BPF object, fix kbuild first test child finished with -1 ---- end ---- BPF filter subtest 2: FAILED! <<>> Here subtests, "BPF pinning" and "BPF prologue generation" failed and logs shows clang/llvm is needed. After installing clang, testcase passes. Reason on why subtest failure happens though logs has proper debug information: Main function __test__bpf calls test_llvm__fetch_bpf_obj by passing 4th argument as true ( 4th arguments maps to parameter "force" in test_llvm__fetch_bpf_obj ). But this will cause test_llvm__fetch_bpf_obj to skip the check for clang/llvm. Snippet of code part which checks for clang based on parameter "force" in test_llvm__fetch_bpf_obj: <<>> if (!force && (!llvm_param.user_set_param && <<>> Since force is set to "false", test won't get skipped and fails to compile test case. The BPF code compilation needs clang, So pass the fourth argument as "false" and also skip the test if reason for return is "TEST_SKIP" After the patch: <<>> 42: BPF filter : 42.1: Basic BPF filtering : Skip 42.2: BPF pinning : Skip 42.3: BPF prologue generation : Skip <<>> Fixes: ba1fae43 ("perf test: Add 'perf test BPF'") Reviewed-by:Kajol Jain <kjain@linux.ibm.com> Signed-off-by:
Athira Jajeev <atrajeev@linux.vnet.ibm.com> Acked-by:
Ian Rogers <irogers@google.com> Cc: Disha Goel <disgoel@linux.vnet.ibm.com> Cc: Jiri Olsa <jolsa@kernel.org> Cc: linuxppc-dev@lists.ozlabs.org Cc: Madhavan Srinivasan <maddy@linux.vnet.ibm.com> Cc: Michael Ellerman <mpe@ellerman.id.au> Cc: Nageswara R Sastry <rnsastry@linux.ibm.com> Cc: Wang Nan <wangnan0@huawei.com> Link: https://lore.kernel.org/r/20220511115438.84032-1-atrajeev@linux.vnet.ibm.comSigned-off-by:
-
Athira Rajeev authored
The session topology test fails in powerpc pSeries platform. Test logs: <<>> Session topology : FAILED! <<>> This testcases tests cpu topology by checking the core_id and socket_id stored in perf_env from perf session. The data from perf session is compared with the cpu topology information from "/sys/devices/system/cpu/cpuX/topology" like core_id, physical_package_id. In case of virtual environment, detail like physical_package_id is restricted to be exposed. Hence physical_package_id is set to -1. The testcase fails on such platforms since socket_id can't be fetched from topology info. Skip the testcase in powerpc if physical_package_id returns -1. Reviewed-by:
Disha Goel <disgoel@linux.vnet.ibm.com> Acked-by:
-
Thomas Richter authored
The compilation on s390 results in this error: # make DEBUG=y bench/numa.o ... bench/numa.c: In function ‘__bench_numa’: bench/numa.c:1749:81: error: ‘%d’ directive output may be truncated writing between 1 and 11 bytes into a region of size between 10 and 20 [-Werror=format-truncation=] 1749 | snprintf(tname, sizeof(tname), "process%d:thread%d", p, t); ^~ ... bench/numa.c:1749:64: note: directive argument in the range [-2147483647, 2147483646] ... # The maximum length of the %d replacement is 11 characters because of the negative sign. Therefore extend the array by two more characters. Output after: # make DEBUG=y bench/numa.o > /dev/null 2>&1; ll bench/numa.o -rw-r--r-- 1 root root 418320 May 19 09:11 bench/numa.o # Fixes: 3aff8ba0 ("perf bench numa: Avoid possible truncation when using snprintf()") Suggested-by:Namhyung Kim <namhyung@gmail.com> Signed-off-by:
Thomas Richter <tmricht@linux.ibm.com> Cc: Heiko Carstens <hca@linux.ibm.com> Cc: Sumanth Korikkar <sumanthk@linux.ibm.com> Cc: Sven Schnelle <svens@linux.ibm.com> Cc: Vasily Gorbik <gor@linux.ibm.com> Link: https://lore.kernel.org/r/20220520081158.2990006-1-tmricht@linux.ibm.comSigned-off-by:
-
Ian Rogers authored
for_each_shell_test() is already strict in expecting tests to be files and executable. It is sometimes possible when it iterates over all files that it finds one that is executable and lacks a newline character. When this happens the loop never terminates as it doesn't check for EOF. Add the EOF check to make this loop at least bounded by the file size. If the description is returned as NULL then also skip the test. Signed-off-by:
-
Kan Liang authored
The X86 specific arch__intr_reg_mask() is to check whether the kernel and hardware can collect XMM registers. But it doesn't work on some hybrid platform. Without the patch on ADL-N: $ perf record -I? available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10 R11 R12 R13 R14 R15 The config of the test event doesn't contain the PMU information. The kernel may fail to initialize it on the correct hybrid PMU and return the wrong non-supported information. Add the PMU information into the config for the hybrid platform. The same register set is supported among different hybrid PMUs. Checking the first available one is good enough. With the patch on ADL-N: $ perf record -I? available registers: AX BX CX DX SI DI BP SP IP FLAGS CS SS R8 R9 R10 R11 R12 R13 R14 R15 XMM0 XMM1 XMM2 XMM3 XMM4 XMM5 XMM6 XMM7 XMM8 XMM9 XMM10 XMM11 XMM12 XMM13 XMM14 XMM15 Fixes: 6466ec14 ("perf regs x86: Add X86 specific arch__intr_reg_mask()") Reported-by:
Ammy Yi <ammy.yi@intel.com> Signed-off-by:
Kan Liang <kan.liang@linux.intel.com> Acked-by:
-
Athira Rajeev authored
"perf all PMU test" picks the input events from "perf list --raw-dump pmu" list and runs "perf stat -e" for each of the event in the list. In case of powerpc, the PowerVM environment supports events from hv_24x7 and hv_gpci PMU which is of example format like below: - hv_24x7/CPM_ADJUNCT_INST,domain=?,core=?/ - hv_gpci/event,partition_id=?/ The value for "?" needs to be filled in depending on system and respective event. CPM_ADJUNCT_INST needs have core value and domain value. hv_gpci event needs partition_id. Similarly, there are other events for hv_24x7 and hv_gpci having "?" in event format. Hence skip these events on powerpc platform since values like partition_id, domain is specific to system and event. Fixes: 3d5ac9ef ("perf test: Workload test of all PMUs") Signed-off-by:
-
Piyush Malgujar authored
Due to i2c->adap.dev.fwnode not being set, ACPI_COMPANION() wasn't properly found for TWSI controllers. Signed-off-by:
Szymon Balcerak <sbalcerak@marvell.com> Signed-off-by:
Piyush Malgujar <pmalgujar@marvell.com> Signed-off-by:
Wolfram Sang <wsa@kernel.org>
-
Mika Westerberg authored
Before sending a MSI the hardware writes information pertinent to the interrupt cause to a memory location pointed by SMTICL register. This memory holds three double words where the least significant bit tells whether the interrupt cause of master/target/error is valid. The driver does not use this but we need to set it up because otherwise it will perform DMA write to the default address (0) and this will cause an IOMMU fault such as below: DMAR: DRHD: handling fault status reg 2 DMAR: [DMA Write] Request device [00:12.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set To prevent this from happening, provide a proper DMA buffer for this that then gets mapped by the IOMMU accordingly. Signed-off-by:Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by:
From: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
-
Yang Yingliang authored
Fix the missing clk_disable_unprepare() before return from mtk_i2c_probe() in the error handling case. Fixes: d04913ec ("i2c: mt7621: Add MediaTek MT7621/7628/7688 I2C driver") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Reviewed-by:
Stefan Roese <sr@denx.de> Signed-off-by:
-
git://git.kernel.org/pub/scm/virt/kvm/kvmLinus Torvalds authored
Pull kvm fixes from Paolo Bonzini: "ARM: - Correctly expose GICv3 support even if no irqchip is created so that userspace doesn't observe it changing pointlessly (fixing a regression with QEMU) - Don't issue a hypercall to set the id-mapped vectors when protected mode is enabled (fix for pKVM in combination with CPUs affected by Spectre-v3a) x86 (five oneliners, of which the most interesting two are): - a NULL pointer dereference on INVPCID executed with paging disabled, but only if KVM is using shadow paging - an incorrect bsearch comparison function which could truncate the result and apply PMU event filtering incorrectly. This one comes with a selftests update too" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86/mmu: fix NULL pointer dereference on guest INVPCID KVM: x86: hyper-v: fix type of valid_bank_mask KVM: Free new dirty bitmap if creating a new memslot fails KVM: eventfd: Fix false positive RCU usage warning selftests: kvm/x86: Verify the pmu event filter matches the correct event selftests: kvm/x86: Add the helper function create_pmu_event_filter kvm: x86/pmu: Fix the compare function used by the pmu event filter KVM: arm64: Don't hypercall before EL2 init KVM: arm64: vgic-v3: Consistently populate ID_AA64PFR0_EL1.GIC KVM: x86/mmu: Update number of zapped pages even if page list is stable -
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linuxLinus Torvalds authored
Pull clk fixes from Stephen Boyd: "Three clk driver fixes to close out the release - Fix a divider calculation breaking boot on Broadcom bcm2835 - Fix HDMI output on Tanix TX6 mini board by reverting a patch - Fix clk_set_rate_range() calls on at91 by considering the range while calculating the divisor" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: at91: generated: consider range when calculating best rate Revert "clk: sunxi-ng: sun6i-rtc: Add support for H6" clk: bcm2835: fix bcm2835_clock_choose_div
-
