Add multi-packet route input tests, for message reassembly. These will
feed packets to be received by a bound socket, or dropped.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a few tests for single-packet route inputs, testing the
mctp_route_input function.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a few tests for the initial packet ingress through
mctp_pkttype_receive function; mainly packet header sanity checks. Full
input routing checks will be added as a separate change.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new object for shared test utilities
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

This change adds the first kunit test for the mctp subsystem, and an
initial test for the fragmentation path.

We're adding tests under a new net/mctp/test/ directory.

Incorporates a fix for module configs:
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

1. Removed driver specific extra params like download_region,
   address & region_count. The required information is passed
   as part of flash API.
2. IOSM Devlink documentation updated to reflect the same.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
Use netdev->dev_addr write helpers (part 1)

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

This is the first installment of predictably tedious conversion.
It tackles:

  memcpy(netdev->dev_addr, something, ETH_ADDR)

and

  ether_addr_copy(netdev->dev_addr, something)

replacing both with eth_hw_addr_set().

The first 7 patches are done entirely by sparse.
Next 4 were semi-manual because the sparse conversion
resulted in errors.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

eth_hw_addr_set() takes a u8 pointer, like other
etherdevice helpers. Convert the few drivers which
require casts because they memcpy from "endian marked"
types.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert from memcpy(), include is needed.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Manual conversions because we need to get to the member
which is inside an array to have a u8 pointer which
eth_hw_addr_set() expects.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert chelsio drivers from memcpy() and ether_addr_copy()
to eth_hw_addr_set(). They lack includes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Convert net/usb from ether_addr_copy() to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - ether_addr_copy(dev->dev_addr, np)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert Ethernet from ether_addr_copy() to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - ether_addr_copy(dev->dev_addr, np)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert from ether_addr_copy() to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - ether_addr_copy(dev->dev_addr, np)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Convert usb drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, ETH_ALEN)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, ETH_ALEN)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert sw drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, ETH_ALEN)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 406f42fa ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.

Convert misc arch drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():

  @@
  expression dev, np;
  @@
  - memcpy(dev->dev_addr, np, ETH_ALEN)
  + eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Egress VLAN modification using VCAP ES0 on Ocelot switches

This patch set adds support for modifying a VLAN ID at the egress stage
of Ocelot/Felix switch ports. It is useful for replicating a packet on
multiple ports, and each egress port sends it using a different VLAN ID.

Tested by rewriting the VLAN ID of both
(a) packets injected from the CPU port
(b) packets received from an external station on a front-facing port

Adding a selftest to make sure it doesn't bit-rot, and if it does, that
it can be traced back easily.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

For this test we are exercising the VCAP ES0 block's ability to match on
a packet with a given VLAN ID, and push an ES0 TAG A with a VID derived
from VID_A_VAL plus the classified VLAN.

$eth3.200 is the generator port
$eth0 is the bridged DUT port that receives
$eth1 is the bridged DUT port that forwards and rewrites VID 200 to 300
      on egress via VCAP ES0
$eth2 is the port that receives from the DUT port $eth1

Since the egress rewriting happens outside the bridging service, VID 300
does not need to be in the bridge VLAN table of $eth1.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There will be one more VLAN modification selftest added, this time for
egress. Rename the one that exists right now to be more specific.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Looks like when I wrote the selftests I was using a network manager that
brought up the ports automatically. In order to not rely on that, let
the script open them up.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, all packets injected into Ocelot switches are classified to
VLAN 0, regardless of whether they are VLAN-tagged or not. This is
because the switch only looks at the VLAN TCI from the DSA tag.

VLAN 0 is then stripped on egress due to REW_TAG_CFG_TAG_CFG. There are
2 cases really, below is the explanation for ocelot_port_set_native_vlan:

- Port is VLAN-aware, we set REW_TAG_CFG_TAG_CFG to 1 (egress-tag all
  frames except VID 0 and the native VLAN) if a native VLAN exists, or
  to 3 otherwise (tag all frames, including VID 0).

- Port is VLAN-unaware, we set REW_TAG_CFG_TAG_CFG to 0 (port tagging
  disabled, classified VLAN never appears in the packet).

One can already see an inconsistency: when a native VLAN exists, VID 0
is egress-untagged, but when it doesn't, VID 0 is egress-tagged.

So when we do this:
ip link add br0 type bridge vlan_filtering 1
ip link set swp0 master br0
bridge vlan del dev swp0 vid 1
bridge vlan add dev swp0 vid 1 pvid # but not untagged

and we ping through swp0, packets will look like this:

MAC > 33:33:00:00:00:02, ethertype 802.1Q (0x8100): vlan 0, p 0,
	ethertype 802.1Q (0x8100), vlan 1, p 0, ethertype IPv6 (0x86dd),
	ICMP6, router solicitation, length 16

So VID 1 frames (sent that way by the Linux bridge) are encapsulated in
a VID 0 header - the classified VLAN of the packets as far as the hw is
concerned. To avoid that, what we really need to do is stop injecting
packets using the classified VLAN of 0.

This patch strips the VLAN header from the skb payload, if that VLAN
exists and if the port is under a VLAN-aware bridge. Then it copies that
VLAN header into the DSA injection frame header.

A positive side effect is that VCAP ES0 VLAN rewriting rules now work
for packets injected from the CPU into a port that's under a VLAN-aware
bridge, and we are able to match those packets by the VLAN ID that was
sent by the network stack, and not by VLAN ID 0.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The VLAN TCI contains more than the VLAN ID, it also has the VLAN PCP
and Drop Eligibility Indicator.

If the ocelot driver is going to write the VLAN header inside the DSA
tag, it could just as well write the entire TCI.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently the ocelot driver does support the 'vlan modify' action, but
in the ingress chain, and it is offloaded to VCAP IS1. This action
changes the classified VLAN before the packet enters the bridging
service, and the bridging works with the classified VLAN modified by
VCAP IS1.

That is good for some use cases, but there are others where the VLAN
must be modified at the stage of the egress port, after the packet has
exited the bridging service. One example is simulating IEEE 802.1CB
active stream identification filters ("active" means that not only the
rule matches on a packet flow, but it is also able to change some
headers). For example, a stream is replicated on two egress ports, but
they must have different VLAN IDs on egress ports A and B.

This seems like a task for the VCAP ES0, but that currently only
supports pushing the ES0 tag A, which is specified in the rule. Pushing
another VLAN header is not what we want, but rather overwriting the
existing one.

It looks like when we push the ES0 tag A, it is actually possible to not
only take the ES0 tag A's value from the rule itself (VID_A_VAL), but
derive it from the following formula:

ES0_TAG_A = Classified VID + VID_A_VAL

Otherwise said, ES0_TAG_A can be used to increment with a given value
the VLAN ID that the packet was already classified to, and the packet
will have this value as an outer VLAN tag. This new VLAN ID value then
gets stripped on egress (or not) according to the value of the native
VLAN from the bridging service.

While the hardware will happily increment the classified VLAN ID for all
packets that match the ES0 rule, in practice this would be rather
insane, so we only allow this kind of ES0 action if the ES0 filter
contains a VLAN ID too, so as to restrict the matching on a known
classified VLAN. If we program VID_A_VAL with the delta between the
desired final VLAN (ES0_TAG_A) and the classified VLAN, we obtain the
desired behavior.

It doesn't look like it is possible with the tc-vlan action to modify
the VLAN ID but not the PCP. In hardware it is possible to leave the PCP
to the classified value, but we unconditionally program it to overwrite
it with the PCP value from the rule.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Add missing clock-names property,
  - Add example compatible values for PHY subnode.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

- Drop unneeded interrupt-parent,
  - Convert to new style CPG/MSSR bindings,
  - Add missing power-domains and resets properties,
  - Update PHY subnode:
      - Add example compatible values,
      - Add micrel,led-mode and reset-gpios examples.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

napi_gro_complete always returned the same value, NET_RX_SUCCESS
And the value was not used anywhere
Signed-off-by: Gyumin Hwang <hkm73560@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Shannon Nelson says:

====================
ionic: housekeeping updates

These are a few changes for code clean up and a couple
more lock management tweaks.

v2: rebased
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the lif parameter for use in an error message, and
to better match the style of most of the functions calls.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Simplify the code a little by keeping the send_to_hw decision
inside of ionic_qcq_disable rather than in the callers.  Also,
add ENXIO to the decision expression.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split the adminq wait into smaller polling periods in order
to watch for broken firmware and not have to wait for the full
adminq devcmd_timeout.

Generally, adminq commands take fewer than 2 msecs.  If the
FW is busy they can take longer, but usually still under 100
msecs.  We set the polling period to 100 msecs in order to
start snooping on FW status when a command is taking longer
than usual.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Widen the coverage of the queue_lock to be sure the lif init
and lif deinit actions are protected.  This addresses a hang
seen when a Tx Timeout action was attempted at the same time
as a FW Reset was started.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move creation and deletion of lif mutex a level out to
lif creation and delete, rather than in init and deinit.
This assures that nothing will get hung if anything is waiting
on the mutex while the driver is clearing the lif while handling
the fw_down/fw_up cycle.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

If the PCI connection is broken, reading the FW version string
will only get 0xff bytes, which shouldn't get printed.  This
checks the first byte and prints only the first 4 bytes
if non-ASCII.

Also, add a limit to the string length printed when a valid
string is found, just in case it is not properly terminated.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

These debug stats are not really useful, their collection is
likely detrimental to performance, and they suck up a lot
of memory which never gets used if no one ever enables the
priv-flag to print them, so just remove these bits.
Signed-off-by: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>

Biju Das says:

====================
Fillup stubs for Gigabit Ethernet driver support

The DMAC and EMAC blocks of Gigabit Ethernet IP found on RZ/G2L SoC are
similar to the R-Car Ethernet AVB IP.

The Gigabit Ethernet IP consists of Ethernet controller (E-MAC), Internal
TCP/IP Offload Engine (TOE)  and Dedicated Direct memory access controller
(DMAC).

With a few changes in the driver we can support both IPs.

This patch series is for adding Gigabit ethernet driver support to RZ/G2L SoC.

The number of patches after incorporatng RFC review comments is 18.
So split the patches into 2 patchsets (10 + 8).

This series is the second patchset, aims to fillup all the stubs for the
Gigabit Ethernet driver.

This patch series depend upon [1]
[1] https://lore.kernel.org/linux-renesas-soc/20211001150636.7500-1-biju.das.jz@bp.renesas.com/T/#t

RFC->V1:
 * used rx_max_buf_size instead of rx_2k_buffers feature bit.
 * renamed "rgeth" to "gbeth".
 * renamed ravb_rx_ring_free to ravb_rx_ring_free_rcar
 * renamed ravb_rx_ring_format to ravb_rx_ring_format_rcar
 * renamed ravb_alloc_rx_desc to ravb_alloc_rx_desc_rcar
 * renamed ravb_rcar_rx to ravb_rx_rcar
 * Added Sergey's Rb tag for patch #6.
 * Moved CSR0 initialization to patch #8.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize GbEthernet E-MAC found on RZ/G2L SoC.
This patch also renames ravb_set_rate to ravb_set_rate_rcar and
ravb_rcar_emac_init to ravb_emac_init_rcar to be consistent with
the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RZ/G2L supports half duplex mode.
Add a half_duplex hw feature bit to struct ravb_hw_info for
supporting half duplex mode for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>

E-MAC on R-Car supports magic packet detection, whereas RZ/G2L
does not support this feature. Add magic_pkt to struct ravb_hw_info
and enable this feature only for R-Car.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>