The error check on err is redundant as it is being checked
previously each time it has been updated.  Remove this redundant
check.

Detected with CoverityScan, CID#140030("Logically dead code")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This bug is harmless because it's just a sanity check and we always
pass valid values for "encap_type" but the test is off by one.

Fixes: 9b410801 ("sfc: insert catch-all filters for encapsulated traffic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.

To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).

To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.

Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"

https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for enabling or disabling the lane swapping (called
"port mirroring" in PHY's CFG4 register) feature of the DP83867 TI's PHY
device.

One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the documentation to avoid PHY lane swapping. This is a boolean
entry to notify the phy device drivers that the TX/RX lanes NO need
to be swapped.
The use case for this binding mostly happens after wrong HW
configuration of PHY IC during bootstrap.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: Incorrect use of phy_read_status()

This patch series removes incorrect uses of phy_read_status() which can clobber
the PHY device link while we are executing with the state machine running.

greth was potentially another candidate, but it does funky stuff with
auto-negotation that I am still trying to understand.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a9191 ("phy state machine: failsafe leave invalid RUNNING state")
Reported-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as off
811a9191 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a9191 ("phy state machine: failsafe leave invalid RUNNING state")

Since we don't have anything special, switch to the generic
phy_ethtool_get_link_ksettings() function now.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Calling phy_read_status() means that we may call into
genphy_read_status() which in turn will use genphy_update_link() which
can make changes to phydev->link outside of the state machine's state
transitions. This is an invalid behavior that is now caught as of
811a9191 ("phy state machine: failsafe leave invalid RUNNING state")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2017-01-31

This series includes some updates to mlx5 core and ethernet driver.

We got one patch from Or to fix some static checker warnings.

2nd patche from Dan came to add the support for 128B cache line
in the HCA, which will configures the hardware to use 128B alignment only
on systems with 128B cache lines, otherwise it will be kept as the current
default of 64B.

From me three patches to support no inline copy on TX on ConnectX-5 and
later HCAs.  Starting with two small infrastructure changes and
refactoring patches followed by two patches to add the actual support for
both xmit ndo and XDP xmit routines.
Last patch is a simple fix to return a mistakenly removed pointer from the
SQ structure, which was remove in previous submission of mlx5 4K UAR.

Saeed.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to update jiffies in txq->trans_start twice, it's supposed to be
done in netdev_start_xmit() and anyway is re-written. Also, no reason to
update trans time in case of an error.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Add XDP support.

The first 10 patches refactor the code (rx/tx code paths and ring logic)
and add the basic infrastructure to support XDP.  The 11th patch adds
basic ndo_xdp to support XDP_DROP and XDP_PASS only.  The 12th patch
completes the series with XDP_TX.

Thanks to Andy Gospodarek for testing and uncovering some bugs.

v3: Removed Kconfig option.
    Pass modified offset and length to stack for XDP_PASS.
    Improved buffer recycling scheme for XDP_TX.
    Other minor fixes.

v2: Addressed review comments from Alexei Starovoitov, Jakub Kicinski,
and David Miller:
	- Added missing dma syncs.
	- Added XDP headroom support.
	- Added tracing in exception path.
	- Clarified a parameter change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add dedicated transmit function and transmit completion handler for
XDP.  The XDP transmit logic and completion logic are different than
regular TX ring.  The TX buffer is recycled back to the RX ring when
it completes.

v3: Improved the buffer recyling scheme for XDP_TX.

v2: Add trace_xdp_exception().
    Add dma_sync.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add basic ndo_xdp support to setup and query program, configure the NIC
to run in rx page mode, and support XDP_PASS, XDP_DROP, XDP_ABORTED
actions only.

v3: Pass modified offset and length to stack for XDP_PASS.
    Remove Kconfig option.

v2: Added trace_xdp_exception()
    Added dma_syncs.
    Added XDP headroom support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Tested-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

XDP_TX requires a different function to handle completion.  Add a
function pointer to handle tx completion logic.  Regular TX rings
will be assigned the current bnxt_tx_int() for the ->tx_int()
function pointer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add logic for an extra set of TX rings for XDP.  If enabled, this
set of TX rings equals the number of RX rings and shares the same
IRQ as the RX ring set.  A new field bp->tx_nr_rings_xdp is added
to keep track of these TX XDP rings.  Adjust all other relevant functions
to handle bp->tx_nr_rings_xdp.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To support XDP_TX, we need to add a set of dedicated TX rings, each
associated with the NAPI of an RX ring.  To assign XDP rings and regular
rings in a flexible way, we add a bp->tx_ring_map[] array to do the
remapping.  The netdev txq index is stored in the new field txq_index
so that we can retrieve the netdev txq when handling TX completions.
In this patch, before we introduce XDP_TX, the mapping is 1:1.

v2: Fixed a bug in bnxt_tx_int().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, bnxt_setup_tc() and bnxt_set_channels() have similar and
duplicated code to check and reserve rx and tx rings.  Add a new
function bnxt_reserve_rings() to centralize the logic.  This will
make it easier to add XDP_TX support which requires allocating a
new set of TX rings.

Also, the tx ring checking logic in bnxt_setup_msix() can be removed.
The rings have been reserved before hand.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the current code, we have separate rx_event and agg_event parameters
to keep track of rx and aggregation events.  Combine these events into
an u8 event mask with different bits defined for different events.  This
way, it is easier to expand the logic to include XDP tx events.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This mode is to support XDP.  In this mode, each rx ring is configured
with page sized buffers for linear placement of each packet.  MTU will be
restricted to what the page sized buffers can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the global constants BNXT_RX_OFFSET and BNXT_RX_DMA_OFFSET to
device parameters.  This will make it easier to support XDP with
headroom support which requires different RX buffer offsets.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When driver is running in XDP mode, rx buffers are DMA mapped as
DMA_BIDIRECTIONAL.  Add a field so the code will map/unmap rx buffers
according to this field.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To support XDP_TX, we need the RX buffer's DMA address to transmit the
packet.  Convert the DMA address field to a permanent field in
bnxt_sw_rx_bd.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Minor refactoring of bnxt_rx_skb() so that it can easily be replaced by
a new function that handles packets in a single page.  Also, use a
function pointer bp->rx_skb_func() to switch to a new function when
we add the new mode in the next patch.

Add a new field data_ptr that points to the packet data in the
bnxt_sw_rx_bd structure.  The original data field is changed to void
pointer so that it can either hold the kmalloc'ed data or a page
pointer.

The last parameter of bnxt_rx_skb() which was the length parameter is
changed to include the payload offset of the packet in the upper 16 bit.
The offset is needed to support the rx page mode and is not used in
this existing function.

v3: Added a new data_ptr parameter to bp->rx_skb_func().  The caller
has the option to modify the starting address of the packet.  This
will be needed when XDP with headroom support is added.

v2: Changed the name of the last parameter to offset_and_len to make the
code more clear.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To support setting the pause parameters, the driver can no longer just
mirror the PHY.  The set_pauseparam feature allows the driver to
force the setting in the MAC, regardless of how the PHY is configured.
This means that we now need to maintain an internal state for pause
frame support, and so get_pauseparam also needs to be updated.

If the interface is already running when the setting is changed, then
the interface is reset.

Note that if the MAC is configured to enable RX pause frame support
(i.e. it transmits pause frames to throttle the other end), but the
PHY is configured to block those frames, then the feature will not work.

Also some buffer size initialization code into emac_init_adapter(),
so that it lives with similar code, including the initializtion of
pause frame support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Julian Anastasov says:

====================
net: dst_confirm replacement

	This patchset addresses the problem of neighbour
confirmation where received replies from one nexthop
can cause confirmation of different nexthop when using
the same dst. Thanks to YueHaibing <yuehaibing@huawei.com>
for tracking the dst->pending_confirm problem.

	Sockets can obtain cached output route. Such
routes can be to known nexthop (rt_gateway=IP) or to be
used simultaneously for different nexthop IPs by different
subnet prefixes (nh->nh_scope = RT_SCOPE_HOST, rt_gateway=0).

	At first look, there are more problems:

- dst_confirm() sets flag on dst and not on dst->path,
as result, indication is lost when XFRM is used

- DNAT can change the nexthop, so the really used nexthop is
not confirmed

	So, the following solution is to avoid using
dst->pending_confirm.

	The current dst_confirm() usage is as follows:

Protocols confirming dst on received packets:
- TCP (1 dst per socket)
- SCTP (1 dst per transport)
- CXGB*

Protocols supporting sendmsg with MSG_CONFIRM [ | MSG_PROBE ] to
confirm neighbour:
- UDP IPv4/IPv6
- ICMPv4 PING
- RAW IPv4/IPv6
- L2TP/IPv6

MSG_CONFIRM for other purposes (fix not needed):
- CAN

Sending without locking the socket:
- UDP (when no cork)
- RAW (when hdrincl=1)

Redirects from old to new GW:
- rt6_do_redirect

	The patchset includes the following changes:

1. sock: add sk_dst_pending_confirm flag

- used only by TCP with patch 4 to remember the received
indication in sk->sk_dst_pending_confirm

2. net: add dst_pending_confirm flag to skbuff

- skb->dst_pending_confirm will be used by all protocols
in following patches, via skb_{set,get}_dst_pending_confirm

3. sctp: add dst_pending_confirm flag

- SCTP uses per-transport dsts and can not use
sk->sk_dst_pending_confirm like TCP

4. tcp: replace dst_confirm with sk_dst_confirm

5. net: add confirm_neigh method to dst_ops

- IPv4 and IPv6 provision for slow neigh lookups for MSG_PROBE users.
I decided to use neigh lookup only for this case because on
MSG_PROBE the skb may pass MTU checks but it does not reach
the neigh confirmation code. This patch will be used from patch 6.

- xfrm_confirm_neigh: we use the last tunnel address, if present.
When there are only transports, the original dest address is used.

6. net: use dst_confirm_neigh for UDP, RAW, ICMP, L2TP

- dst_confirm conversion for UDP, RAW, ICMP and L2TP/IPv6

- these protocols use MSG_CONFIRM propagated by ip*_append_data
to skb->dst_pending_confirm. sk->sk_dst_pending_confirm is not
used because some sending paths do not lock the socket. For
MSG_PROBE we use the slow lookup (dst_confirm_neigh).

- there are also 2 cases that need the slow lookup:
__ip6_rt_update_pmtu and rt6_do_redirect. I hope
&ipv6_hdr(skb)->saddr is the correct nexthop address to use here.

7. net: pending_confirm is not used anymore

- I failed to understand the CXGB* code, I see dst_confirm()
calls but I'm not sure dst_neigh_output() was called. For now
I just removed the dst->pending_confirm flag and left all
dst_confirm() calls there. Any better idea?

- Now may be old function neigh_output() should be restored
instead of dst_neigh_output?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As last step, we can remove the pending_confirm flag.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effe ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bed ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.

The datagram protocols can use MSG_CONFIRM to confirm the
neighbour. When used with MSG_PROBE we do not reach the
code where neighbour is confirmed, so we have to do the
same slow lookup by using the dst_confirm_neigh() helper.
When MSG_PROBE is not used, ip_append_data/ip6_append_data
will set the skb flag dst_pending_confirm.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effe ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bed ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add confirm_neigh method to dst_ops and use it from IPv4 and IPv6
to lookup and confirm the neighbour. Its usage via the new helper
dst_confirm_neigh() should be restricted to MSG_PROBE users for
performance reasons.

For XFRM prefer the last tunnel address, if present. With help
from Steffen Klassert.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
Use the new sk_dst_confirm() helper to propagate the
indication from received packets to sock_confirm_neigh().
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effe ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bed ("ipv4: Cache output routes in fib_info nexthops.")
Tested-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new transport flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
The flag is propagated from transport to every packet.
It is reset when cached dst is reset.
Reported-by: YueHaibing <yuehaibing@huawei.com>
Fixes: 5110effe ("net: Do delayed neigh confirmation.")
Fixes: f2bb4bed ("ipv4: Cache output routes in fib_info nexthops.")
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new skbuff flag to allow protocols to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.

Add sock_confirm_neigh() helper to confirm the neighbour and
use it for IPv4, IPv6 and VRF before dst_neigh_output.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add new sock flag to allow sockets to confirm neighbour.
When same struct dst_entry can be used for many different
neighbours we can not use it for pending confirmations.
As not all call paths lock the socket use full word for
the flag.

Add sk_dst_confirm as replacement for dst_confirm when
called for received packets.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When PSAMPLE is a loadable module, spectrum must not be built-in:

drivers/net/built-in.o: In function `mlxsw_sp_rx_listener_sample_func':
spectrum.c:(.text+0xe357e): undefined reference to `psample_sample_packet'

This adds a Kconfig dependency to enforce usable configurations.

Fixes: 98d0f7b9 ("mlxsw: spectrum: Add packet sample offloading support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes the following sparse warnings:

net/ipv6/seg6_iptunnel.c:58:5: warning:
 symbol 'nla_put_srh' was not declared. Should it be static?
net/ipv6/seg6_iptunnel.c:238:5: warning:
 symbol 'seg6_input' was not declared. Should it be static?
net/ipv6/seg6_iptunnel.c:254:5: warning:
 symbol 'seg6_output' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove duplicated include.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove .owner field if calls are used which set it automatically.

Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

module_spi_driver() makes the code simpler by eliminating
boilerplate code.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>