- 07 Jan, 2016 22 commits
-
-
Finn Thain authored
If a target disappears from the SCSI bus, NCR5380_select() may subsequently fail with a time-out. In this situation, scsi_done is called and NCR5380_select() returns 0. Both hostdata->connected and hostdata->selecting are NULL and the main loop should proceed with the next command in the issue queue. Clarify this logic. Signed-off-by:
Finn Thain <fthain@telegraphics.com.au> Reviewed-by:
Hannes Reinecke <hare@suse.com> Tested-by:
Ondrej Zary <linux@rainbow-software.org> Tested-by:
Michael Schmitz <schmitzmic@gmail.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com>
-
Finn Thain authored
Remove the restart_select and targets_present variables introduced in Linux v1.1.38. The former was used only for a questionable debug printk and the latter "so we can call a select failure a retryable condition". Well, retrying select failure in general is a different problem to a target that doesn't assert BSY. We need to handle these two cases differently; the latter case can be left to the SCSI ML. Signed-off-by:
-
Finn Thain authored
The "failed" label in NCR5380_select() is not helpful. Some failures return 0, others -1. Use return instead of goto to improve clarity and brevity, like atari_NCR5380.c does. Fix the relevant comments. Signed-off-by:
-
Finn Thain authored
Remove the duplicate write to the Select Enable Register that appeared in v1.1.38. Also remove the redundant write to Initiator Command Register prior to calling do_abort(). Signed-off-by:
-
Finn Thain authored
The aborted flag was introduced in v1.1.38 but never used. Remove it. Signed-off-by:
-
Finn Thain authored
Make use of do_reset() in the bus reset handler in atari_NCR5380.c. The version in NCR5380.c already does so. Keep them in sync. Signed-off-by:
-
Finn Thain authored
The atari_NCR5380.c core driver now takes care of bus reset upon driver initialization if required (same as NCR5380.c). Move the Toshiba CD-ROM support into the core driver, enabled with a host flag, so that all NCR5380 drivers can make use of it. Drop the RESET_BOOT macros and the ATARI_SCSI_RESET_BOOT and ATARI_SCSI_TOSHIBA_DELAY Kconfig symbols, which are now redundant. Remove the atari_scsi_reset_boot(), mac_scsi_reset_boot() and sun3_scsi_reset_boot() routines. None of this duplicated code is needed now that all drivers can use NCR5380_maybe_reset_bus(). This brings atari_scsi, mac_scsi and sun3_scsi into line with all of the other NCR5380 drivers. The bus reset may raise an interrupt. That would be new behaviour for atari_scsi only when CONFIG_ATARI_SCSI_RESET_BOOT=n. The ST DMA interrupt is not assigned to atari_scsi at this stage, so CONFIG_ATARI_SCSI_RESET_BOOT=y may well be problematic already. Regardless, do_reset() now raises and clears the interrupt within local_irq_save/restore which should avoid problems. Signed-off-by:
-
Finn Thain authored
Merge the bus reset code from NCR5380.c into atari_NCR5380.c. This allows for removal of a lot of duplicated code conditional on the RESET_BOOT macro (in the next patch). The atari_NCR5380.c fork lacks the do_reset() and NCR5380_poll_politely() routines from NCR5380.c, so introduce them. They are indispensible. Keep the two implementations in sync. Signed-off-by:
-
Finn Thain authored
Move board-specific code like this, NCR5380_write(C400_CONTROL_STATUS_REG, CSR_BASE); from the core driver to the board driver. Eliminate the NCR53C400 macro from the core driver. Removal of all macros like this one will be necessary in order to have one core driver that can support all kinds of boards. Signed-off-by:
-
Finn Thain authored
This patch splits the NCR5380_init() function into two parts, similar to the scheme used with atari_NCR5380.c. This avoids two problems. Firstly, NCR5380_init() may perform a bus reset, which would cause the chip to assert IRQ. The chip is unable to mask its bus reset interrupt. Drivers can't call request_irq() before calling NCR5380_init(), because initialization must happen before the interrupt handler executes. If driver initialization causes an interrupt it may be problematic on some platforms. To avoid that, first move the bus reset code into NCR5380_maybe_reset_bus(). Secondly, NCR5380_init() contains some board-specific interrupt setup code for the NCR53C400 that does not belong in the core driver. In moving this code, better not re-order interrupt initialization and bus reset. Again, the solution is to move the bus reset code into NCR5380_maybe_reset_bus(). Signed-off-by:
-
Finn Thain authored
This macro makes the code cryptic. Remove it. Signed-off-by:
-
Finn Thain authored
The NCR5380_local_declare and NCR5380_setup macros exist to define and initialize a particular local variable, to provide the address of the chip registers needed for the driver's implementation of its NCR5380_read/write register access macros. In cumana_1 and macscsi, these macros generate pointless code like this, struct Scsi_Host *_instance; _instance = instance; In pas16, the use of NCR5380_read/write in pas16_hw_detect() requires that the io_port local variable has been defined and initialized, but the NCR5380_local_declare and NCR5380_setup macros can't be used for that purpose because the Scsi_Host struct has not yet been instantiated. Moreover, these macros were removed from atari_NCR5380.c long ago and now they constitute yet another discrepancy between the two core driver forks. Remove these "optimizations". Signed-off-by:
-
Finn Thain authored
ASM macro is never defined. rtrc in pas16.c is not used. NCR5380_map_config, do_NCR5380_intr, do_t128_intr and do_pas16_intr are unused. NCR_NOT_SET harms readability. Remove them. Signed-off-by:
-
Finn Thain authored
Replace {P,T,DTC}DEBUG_INIT with NDEBUG_INIT. Remove dead debugging code, including code that's conditional upon *DEBUG_TRANSFER. Signed-off-by: -
Finn Thain authored
Signed-off-by:
-
Finn Thain authored
The NVRAM location of this byte is 16, as documented in http://toshyp.atari.org/en/004009.html This was confirmed by Michael Schmitz, by setting the SCSI host ID under EmuTOS and then checking the value in /proc/driver/nvram and /dev/nvram under Linux. Signed-off-by:
-
Manoj Kumar authored
This drop enables a future card with a device id of 0x0600 to be recognized by the cxlflash driver. As per the design, the Accelerator Function Unit (AFU) for this new IBM CXL Flash Adapter retains the same host interface as the previous generation. For the early prototypes of the new card, the driver with this change behaves exactly as the driver prior to this behaved with the earlier generation card. Therefore, no card specific programming has been added. These card specific changes can be staged in later if needed. Signed-off-by:
Manoj N. Kumar <manoj@linux.vnet.ibm.com> Acked-by:
Matthew R. Ochs <mrochs@linux.vnet.ibm.com> Reviewed-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Signed-off-by:
-
Manoj Kumar authored
If an async error interrupt is generated, and the error requires the FC link to be reset, it cannot be performed in the interrupt context. So a work element is scheduled to complete the link reset in a process context. If either an EEH event or an escalation occurs in between when the interrupt is generated and the scheduled work is started, the MMIO space may no longer be available. This will cause an oops in the worker thread. [ 606.806583] NIP kthread_data+0x28/0x40 [ 606.806633] LR wq_worker_sleeping+0x30/0x100 [ 606.806694] Call Trace: [ 606.806721] 0x50 (unreliable) [ 606.806796] wq_worker_sleeping+0x30/0x100 [ 606.806884] __schedule+0x69c/0x8a0 [ 606.806959] schedule+0x44/0xc0 [ 606.807034] do_exit+0x770/0xb90 [ 606.807109] die+0x300/0x460 [ 606.807185] bad_page_fault+0xd8/0x150 [ 606.807259] handle_page_fault+0x2c/0x30 [ 606.807338] wait_port_offline.constprop.12+0x60/0x130 [cxlflash] To prevent the problem space area from being unmapped, when there is pending work, a mapcount (using the kref mechanism) is held. The mapcount is released only when the work is completed. The last reference release is tied to the unmapping service. Signed-off-by:
Uma Krishnan <ukrishn@linux.vnet.ibm.com> Signed-off-by:
-
Manoj Kumar authored
After a few iterations of resetting the card, either during EEH recovery, or a host_reset the following is seen in the logs. cxlflash 0008:00: cxlflash_queuecommand: could not get a free command At every reset of the card, the commands that are outstanding are being leaked. No effort is being made to reap these commands. A few more resets later, the above error message floods the logs and the card is rendered totally unusable as no free commands are available. Iterated through the 'cmd' queue and printed out the 'free' counter and found that on each reset certain commands were in-use and stayed in-use through subsequent resets. To resolve this issue, when the card is reset, reap all the commands that are active/outstanding. Signed-off-by:
-
Uma Krishnan authored
Having a date for the driver requires it to be updated quite often. Removing the date which is not necessary. Also made use of the existing symbol to print the driver name. Signed-off-by:
-
Matthew R. Ochs authored
Applications which use virtual LUN's that are backed by a physical LUN over both adapter ports may experience an I/O failure in the event of a link loss (e.g. cable pull). Virtual LUNs may be accessed through one or both ports of the adapter. This access is encoded in the translation entries that comprise the virtual LUN and used by the AFU for load-balancing I/O and handling failover scenarios. In a link loss scenario, even though the AFU is able to maintain connectivity to the LUN, it is up to the application to retry the failed I/O. When applications are unaware of the virtual LUN's underlying topology, they are unable to make a sound decision of when to retry an I/O and therefore are forced to make their reaction to a failed I/O absolute. The result is either a failure to retry I/O or increased latency for scenarios where a retry is pointless. To remedy this scenario, provide feedback back to the application on virtual LUN creation as to which ports the LUN may be accessed. LUN's spanning both ports are candidates for a retry in a presence of an I/O failure. Signed-off-by:
-
Manoj Kumar authored
The original fix to escalate a 'login timed out' error to a LINK_RESET was only made for one of the two ports on the card. This fix resolves the same issue for the second port (port 1). Signed-off-by:
-
- 06 Jan, 2016 9 commits
-
-
K. Y. Srinivasan authored
On the interrupt path, we repeatedly establish the pointer to the storvsc_device. While the compiler does inline get_in_stor_device() (and other static functions) in the call chain in the interrupt path, the compiler is repeatedly inlining the call to get_in_stor_device() each time it is invoked. The return value of get_in_stor_device() can be cached in the interrupt path since there is higher level serialization in place to ensure correct handling when the module unload races with the processing of an incoming message from the host. Optimize this code path by caching the pointer to storvsc_device and passing it as an argument. Signed-off-by:
K. Y. Srinivasan <kys@microsoft.com> Reviewed-by:
Long Li <longli@microsoft.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.de> Reviewed-by:
Alex Ng <alexng@microsoft.com> Signed-off-by:
-
K. Y. Srinivasan authored
The function storvsc_channel_init() repeatedly interacts with the host to extract various channel properties. Refactor this code to eliminate code repetition. Signed-off-by:
-
K. Y. Srinivasan authored
For FC devices managed by this driver, atttach the appropriate transport template. This will allow us to create the appropriate sysfs files for these devices. With this we can publish the wwn for both the port and the node. Signed-off-by:
-
K. Y. Srinivasan authored
The hv_fc_wwn_packet is exchanged over vmbus. Make the definition in Linux match the Windows definition. Signed-off-by:
-
Wilfried Weissmann authored
Add SGPIO support to Marvell 94xx. Signed-off-by:
Wilfried Weissmann <Wilfried.Weissmann@gmx.at> Reviewed-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Signed-off-by:
-
Tomas Henzl authored
It might happen that we try to free an already freed pointer. Reported-by:
Maurizio Lombardi <mlombard@redhat.com> Signed-off-by:
Tomas Henzl <thenzl@redhat.com> Acked-by:
Chaitra P B <chaitra.basappa@avagotech.com> Signed-off-by:
-
Don Brace authored
Adding a new method to display enclosure device information. Reviewed-by:
Justin Lindley <justin.lindley@pmcs.com> Reviewed-by:
Kevin Barnett <kevin.barnett@pmcs.com> Reviewed-by:
Scott Teel <scott.teel@pmcs.com> Reviewed-by:
Don Brace <don.brace@pmcs.com> Signed-off-by:
-
Don Brace authored
SAS transport places devices on bus 0 but driver was setting the bus to 3. Reviewed-by:
-
Don Brace authored
Left off some changes from Rasmus Villemoes where he changed snprintf to scnprintf. Suggested-by:
Rasmus Villemoes <linux@rasmusvillemoes.dk> Reviewed-by:
-
- 05 Jan, 2016 1 commit
-
-
Colin Ian King authored
The max outstanding commands is being printed with a 0x prefix to suggest it is a hex value, when in fact the integer decimal %d format specifier is being used and this is a bit confusing. Use %x instead to match the proceeding 0x prefix. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
- 22 Dec, 2015 8 commits
-
-
Martin K. Petersen authored
The OPTIMAL TRANSFER LENGTH reported by scsi_debug is 64 blocks which translates to 32KB with the default logical block size. That's much lower than what real storage devices typically report (256KB to 1MB). Bump the optimal transfer length to 1024 blocks. Acked-by:
Douglas Gilbert <dgilbert@interlog.com> Reviewed-by:
Ewan Milne <emilne@redhat.com> Signed-off-by:
-
James Smart authored
Update version to 11.0.0.10 for upstream patch set Signed-off-by:
Dick Kennedy <dick.kennedy@avagotech.com> Signed-off-by:
James Smart <james.smart@avagotech.com> Reviewed-by:
Hannes Reinicke <hare@suse.de> Signed-off-by:
-
Punit Vara authored
This patch is to the lpfc_els.c which resolves following warning reported by coccicheck: WARNING: kzalloc should be used for rdp_context, instead of kmalloc/memset Signed-off-by:
Punit Vara <punitvara@gmail.com> Signed-off-by:
Sebastian Herbszt <herbszt@gmx.de> Signed-off-by:
-
Markus Elfring authored
The mempool_destroy() function tests whether its argument is NULL and then returns immediately. Thus the test around the calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by:
Markus Elfring <elfring@users.sourceforge.net> Signed-off-by:
-
James Smart authored
Add logging for misconfigured optics acqe reported by fw. Signed-off-by:
-
James Smart authored
Fix external loopback failure. Rx sequence reassembly was incorrect. Signed-off-by:
-
James Smart authored
Fix mbox reuse in PLOGI completion. Moved allocations so that buffer properly init'd. Signed-off-by:
-
James Smart authored
Use new FDMI speed definitions for 10G, 25G and 40G FCoE. Signed-off-by:
-
