Pull HID fixes from Jiri Kosina:

 - revert of commit that caused regression to many Logitech unifying
   receiver users (Jiri Kosina)

 - power management fix for hid-mcp2221 (Hamish Martin)

 - fix for race condition between HID core and HID debug (Charles Yi)

 - a couple of assorted device-ID-specific quirks

* tag 'for-linus-2023112301' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid:
  HID: multitouch: Add quirk for HONOR GLO-GXXX touchpad
  HID: hid-asus: reset the backlight brightness level on resume
  HID: hid-asus: add const to read-only outgoing usb buffer
  Revert "HID: logitech-dj: Add support for a new lightspeed receiver iteration"
  HID: add ALWAYS_POLL quirk for Apple kb
  HID: glorious: fix Glorious Model I HID report
  HID: fix HID device resource race between HID core and debugging support
  HID: apple: add Jamesdonkey and A3R to non-apple keyboards list
  HID: mcp2221: Allow IO to start during probe
  HID: mcp2221: Set driver data before I2C adapter add

Pull networking fixes from Jakub Kicinski:
 "Including fixes from bpf.

  Current release - regressions:

   - Revert "net: r8169: Disable multicast filter for RTL8168H and
     RTL8107E"

   - kselftest: rtnetlink: fix ip route command typo

  Current release - new code bugs:

   - s390/ism: make sure ism driver implies smc protocol in kconfig

   - two build fixes for tools/net

  Previous releases - regressions:

   - rxrpc: couple of ACK/PING/RTT handling fixes

  Previous releases - always broken:

   - bpf: verify bpf_loop() callbacks as if they are called unknown
     number of times

   - improve stability of auto-bonding with Hyper-V

   - account BPF-neigh-redirected traffic in interface statistics

  Misc:

   - net: fill in some more MODULE_DESCRIPTION()s"

* tag 'net-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
  tools: ynl: fix duplicate op name in devlink
  tools: ynl: fix header path for nfsd
  net: ipa: fix one GSI register field width
  tls: fix NULL deref on tls_sw_splice_eof() with empty record
  net: axienet: Fix check for partial TX checksum
  vsock/test: fix SEQPACKET message bounds test
  i40e: Fix adding unsupported cloud filters
  ice: restore timestamp configuration after device reset
  ice: unify logic for programming PFINT_TSYN_MSK
  ice: remove ptp_tx ring parameter flag
  amd-xgbe: propagate the correct speed and duplex status
  amd-xgbe: handle the corner-case during tx completion
  amd-xgbe: handle corner-case during sfp hotplug
  net: veth: fix ethtool stats reporting
  octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx queue than its PF
  net: usb: qmi_wwan: claim interface 4 for ZTE MF290
  Revert "net: r8169: Disable multicast filter for RTL8168H and RTL8107E"
  net/smc: avoid data corruption caused by decline
  nfc: virtual_ncidev: Add variable to check if ndev is running
  dpll: Fix potential msg memleak when genlmsg_put_reply failed
  ...

We don't support CRUD-inspired message types in YNL too well.
One aspect that currently trips us up is the fact that single
message ID can be used in multiple commands (as the response).
This leads to duplicate entries in the id-to-string tables:

devlink-user.c:19:34: warning: initialized field overwritten [-Woverride-init]
   19 |         [DEVLINK_CMD_PORT_NEW] = "port-new",
      |                                  ^~~~~~~~~~
devlink-user.c:19:34: note: (near initialization for ‘devlink_op_strmap[7]’)

Fixes tag points at where the code was generated, the "real" problem
is that the code generator does not support CRUD.

Fixes: f2f9dd16 ("netlink: specs: devlink: add the remaining command to generate complete split_ops")
Link: https://lore.kernel.org/r/20231123030558.1611831-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The makefile dependency is trying to include the wrong header:

<command-line>: fatal error: ../../../../include/uapi//linux/nfsd.h: No such file or directory

The guard also looks wrong.

Fixes: f14122b2 ("tools: ynl: Add source files for nfsd netlink protocol")
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20231123030624.1611925-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The width of the R_LENGTH field of the EV_CH_E_CNTXT_1 GSI register
is 24 bits (not 20 bits) starting with IPA v5.0.  Fix this.

Fixes: faf0678e ("net: ipa: add IPA v5.0 GSI register definitions")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20231122231708.896632-1-elder@linaro.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

syzkaller discovered that if tls_sw_splice_eof() is executed as part of
sendfile() when the plaintext/ciphertext sk_msg are empty, the send path
gets confused because the empty ciphertext buffer does not have enough
space for the encryption overhead. This causes tls_push_record() to go on
the `split = true` path (which is only supposed to be used when interacting
with an attached BPF program), and then get further confused and hit the
tls_merge_open_record() path, which then assumes that there must be at
least one populated buffer element, leading to a NULL deref.

It is possible to have empty plaintext/ciphertext buffers if we previously
bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path.
tls_sw_push_pending_record() already handles this case correctly; let's do
the same check in tls_sw_splice_eof().

Fixes: df720d28 ("tls/sw: Use splice_eof() to flush")
Cc: stable@vger.kernel.org
Reported-by: syzbot+40d43509a099ea756317@syzkaller.appspotmail.com
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20231122214447.675768-1-jannh@google.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Due to a typo, the code checked the RX checksum feature in the TX path.

Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tune message length calculation to make this test work on machines
where 'getpagesize()' returns >32KB. Now maximum message length is not
hardcoded (on machines above it was smaller than 'getpagesize()' return
value, thus we get negative value and test fails), but calculated at
runtime and always bigger than 'getpagesize()' result. Reproduced on
aarch64 with 64KB page size.

Fixes: 5c338112 ("test/vsock: rework message bounds test")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: Bogdan Marcynkov <bmarcynk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20231121211642.163474-1-avkrasnov@salutedevices.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.

Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.

Fixes: e284fc28 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Tony Nguyen says:

====================
ice: restore timestamp config after reset

Jake Keller says:

We recently discovered during internal validation that the ice driver has
not been properly restoring Tx timestamp configuration after a device reset,
which resulted in application failures after a device reset.

After some digging, it turned out this problem is two-fold. Since the
introduction of the PTP support the driver has been clobbering the storage
of the current timestamp configuration during reset. Thus after a reset, the
driver will no longer perform Tx or Rx timestamps, and will report
timestamp configuration as disabled if SIOCGHWTSTAMP ioctl is issued.

In addition, the recently merged auxiliary bus support code missed that
PFINT_TSYN_MSK must be reprogrammed on the clock owner for E822 devices.
Failure to restore this register configuration results in the driver no
longer responding to interrupts from other ports. Depending on the traffic
pattern, this can either result in increased latency responding to
timestamps on the non-owner ports, or it can result in the driver never
reporting any timestamps. The configuration of PFINT_TSYN_MSK was only done
during initialization. Due to this, the Tx timestamp issue persists even if
userspace reconfigures timestamping.

This series fixes both issues, as well as removes a redundant Tx ring field
since we can rely on the skb flag as the primary detector for a Tx timestamp
request.

Note that I don't think this series will directly apply to older stable
releases (even v6.6) as we recently refactored a lot of the PTP code to
support auxiliary bus. Patch 2/3 only matters for the post-auxiliary bus
implementation. The principle of patch 1/3 and 3/3 could apply as far back
as the initial PTP support, but I don't think it will apply cleanly as-is.
====================

Link: https://lore.kernel.org/r/20231121211259.3348630-1-anthony.l.nguyen@intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.

This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.

This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.

Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.

Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:

1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
   timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()

2) ice_ptp_restore_timestamp_mode() which calls
   ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
   calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
   issues an immediate TSYN_TX interrupt to ensure that timestamps which
   may have occurred during the device reset get processed.

Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.

This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.

With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.

Fixes: 77a78115 ("ice: enable receive hardware timestamping")
Fixes: ea9b847c ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Commit d938a8cc ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.

The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.

For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.

If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.

The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.

Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.

This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.

Fixes: d938a8cc ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.

Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.

In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.

Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.

A following change will fix the reset path to properly restore user
timestamping configuration completely.

This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.

Fixes: ea9b847c ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Raju Rangoju says:

====================
amd-xgbe: fixes to handle corner-cases

This series include bug fixes to amd-xgbe driver.
====================

Link: https://lore.kernel.org/r/20231121191435.4049995-1-Raju.Rangoju@amd.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.

Address this by propagating correct information.

Fixes: 7c12aa08 ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.

To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.

Fixes: c5aa9e3b ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.

Fixes: e57f7a3f ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:

$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
 numtxqueues 1 numrxqueues 1

and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.

Fixes: 4fc41805 ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.

Fixes: f0a1913f ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Interface 4 is used by for QMI interface in stock firmware of MF28D, the
router which uses MF290 modem. Rebind it to qmi_wwan after freeing it up
from option driver.
The proper configuration is:

Interface mapping is:
0: QCDM, 1: (unknown), 2: AT (PCUI), 2: AT (Modem), 4: QMI

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  4 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=19d2 ProdID=0189 Rev= 0.00
S:  Manufacturer=ZTE, Incorporated
S:  Product=ZTE LTE Technologies MSM
C:* #Ifs= 5 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=83(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E:  Ad=84(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E:  Ad=86(I) Atr=03(Int.) MxPS=  64 Ivl=2ms
E:  Ad=87(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms

Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://lore.kernel.org/r/20231117231918.100278-3-lech.perczak@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Merge tag 'loongarch-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson

Pull LoongArch fixes from Huacai Chen:
 "Fix several build errors, a potential kernel panic, a cpu hotplug
  issue and update links in documentations"

* tag 'loongarch-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
  Docs/zh_CN/LoongArch: Update links in LoongArch introduction.rst
  Docs/LoongArch: Update links in LoongArch introduction.rst
  LoongArch: Implement constant timer shutdown interface
  LoongArch: Mark {dmw,tlb}_virt_to_page() exports as non-GPL
  LoongArch: Silence the boot warning about 'nokaslr'
  LoongArch: Add __percpu annotation for __percpu_read()/__percpu_write()
  LoongArch: Record pc instead of offset in la_abs relocation
  LoongArch: Explicitly set -fdirect-access-external-data for vmlinux
  LoongArch: Add dependency between vmlinuz.efi and vmlinux.efi

Merge tag 'hyperv-fixes-signed-20231121' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux

Pull hyperv fixes from Wei Liu:

 - One fix for the KVP daemon (Ani Sinha)

 - Fix for the detection of E820_TYPE_PRAM in a Gen2 VM (Saurabh Sengar)

 - Micro-optimization for hv_nmi_unknown() (Uros Bizjak)

* tag 'hyperv-fixes-signed-20231121' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
  x86/hyperv: Use atomic_try_cmpxchg() to micro-optimize hv_nmi_unknown()
  x86/hyperv: Fix the detection of E820_TYPE_PRAM in a Gen2 VM
  hv/hv_kvp_daemon: Some small fixes for handling NM keyfiles

We really don't want to do atomic_read() or anything like that, since we
already have the value, not the lock.  The whole point of this is that
we've loaded the lock from memory, and we want to check whether the
value we loaded was a locked one or not.

The main use of this is the lockref code, which loads both the lock and
the reference count in one atomic operation, and then works on that
combined value.  With the atomic_read(), the compiler would pointlessly
spill the value to the stack, in order to then be able to read it back
"atomically".

This is the qspinlock version of commit c6f4a900 ("asm-generic:
ticket-lock: Optimize arch_spin_value_unlocked()") which fixed this same
bug for ticket locks.

Cc: Guo Ren <guoren@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Link: https://lore.kernel.org/all/CAHk-=whNRv0v6kQiV5QO6DJhjH4KEL36vWQ6Re8Csrnh4zbRkQ@mail.gmail.com/Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

This reverts commit efa5f131.

I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
  was filtered out by the mc filter.
The packet was properly received.

Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.

Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We found a data corruption issue during testing of SMC-R on Redis
applications.

The benchmark has a low probability of reporting a strange error as
shown below.

"Error: Protocol error, got "\xe2" as reply type byte"

Finally, we found that the retrieved error data was as follows:

0xE2 0xD4 0xC3 0xD9 0x04 0x00 0x2C 0x20 0xA6 0x56 0x00 0x16 0x3E 0x0C
0xCB 0x04 0x02 0x01 0x00 0x00 0x20 0x00 0x00 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xE2

It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:

client                  server
        ¦  clc proposal
        ------------->
        ¦  clc accept
        <-------------
        ¦  clc confirm
        ------------->
wait llc confirm
			send llc confirm
        ¦failed llc confirm
        ¦   x------
(after 2s)timeout
                        wait llc confirm rsp

wait decline

(after 1s) timeout
                        (after 2s) timeout
        ¦   decline
        -------------->
        ¦   decline
        <--------------

As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.

This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).

This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.

Fixes: 0fb0b02b ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

syzbot reported an memory leak that happens when an skb is add to
send_buff after virtual nci closed.
This patch adds a variable to track if the ndev is running before
handling new skb in send function.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+6eb09d75211863f15e3e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/00000000000075472b06007df4fb@google.com
Reviewed-by: Bongsu Jeon
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Honor MagicBook 13 2023 has a touchpad which do not switch to the multitouch
mode until the input mode feature is written by the host.  The touchpad do
report the input mode at touchpad(3), while itself working under mouse mode. As
a workaround, it is possible to call MT_QUIRE_FORCE_GET_FEATURE to force set
feature in mt_set_input_mode for such device.

The touchpad reports as BLTP7853, which cannot retrive any useful manufacture
information on the internel by this string at present.  As the serial number of
the laptop is GLO-G52, while DMI info reports the laptop serial number as
GLO-GXXX, this workaround should applied to all models which has the GLO-GXXX.
Signed-off-by: Aoba K <nexp_0x17@outlook.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Some devices managed by this driver automatically set brightness to 0
before entering a suspended state and reset it back to a default
brightness level after the resume:
this has the effect of having the kernel report wrong brightness
status after a sleep, and on some devices (like the Asus RC71L) that
brightness is the intensity of LEDs directly facing the user.

Fix the above issue by setting back brightness to the level it had
before entering a sleep state.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

In the function asus_kbd_set_report the parameter buf is read-only
as it gets copied in a memory portion suitable for USB transfer,
but the parameter is not marked as const: add the missing const and mark
const immutable buffers passed to that function.
Signed-off-by: Denis Benato <benato.denis96@gmail.com>
Signed-off-by: Luke D. Jones <luke@ljones.dev>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Use atomic_try_cmpxchg() instead of atomic_cmpxchg(*ptr, old, new) == old
in hv_nmi_unknown(). On x86 the CMPXCHG instruction returns success in
the ZF flag, so this change saves a compare after CMPXCHG. The generated
asm code improves from:

  3e:	65 8b 15 00 00 00 00 	mov    %gs:0x0(%rip),%edx
  45:	b8 ff ff ff ff       	mov    $0xffffffff,%eax
  4a:	f0 0f b1 15 00 00 00 	lock cmpxchg %edx,0x0(%rip)
  51:	00
  52:	83 f8 ff             	cmp    $0xffffffff,%eax
  55:	0f 95 c0             	setne  %al

to:

  3e:	65 8b 15 00 00 00 00 	mov    %gs:0x0(%rip),%edx
  45:	b8 ff ff ff ff       	mov    $0xffffffff,%eax
  4a:	f0 0f b1 15 00 00 00 	lock cmpxchg %edx,0x0(%rip)
  51:	00
  52:	0f 95 c0             	setne  %al

No functional change intended.

Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Reviewed-by: Michael Kelley <mhklinux@outlook.com>
Link: https://lore.kernel.org/r/20231114170038.381634-1-ubizjak@gmail.comSigned-off-by: Wei Liu <wei.liu@kernel.org>
Message-ID: <20231114170038.381634-1-ubizjak@gmail.com>

We should clean the skb resource if genlmsg_put_reply failed.

Fixes: 9d71b54b ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20231121013709.73323-1-gehao@kylinos.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Daniel Borkmann says:

====================
pull-request: bpf 2023-11-21

We've added 19 non-merge commits during the last 4 day(s) which contain
a total of 18 files changed, 1043 insertions(+), 416 deletions(-).

The main changes are:

1) Fix BPF verifier to validate callbacks as if they are called an unknown
   number of times in order to fix not detecting some unsafe programs,
   from Eduard Zingerman.

2) Fix bpf_redirect_peer() handling which missed proper stats accounting
   for veth and netkit and also generally fix missing stats for the latter,
   from Peilin Ye, Daniel Borkmann et al.

* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
  selftests/bpf: check if max number of bpf_loop iterations is tracked
  bpf: keep track of max number of bpf_loop callback iterations
  selftests/bpf: test widening for iterating callbacks
  bpf: widening for callback iterators
  selftests/bpf: tests for iterating callbacks
  bpf: verify callbacks as if they are called unknown number of times
  bpf: extract setup_func_entry() utility function
  bpf: extract __check_reg_arg() utility function
  selftests/bpf: fix bpf_loop_bench for new callback verification scheme
  selftests/bpf: track string payload offset as scalar in strobemeta
  selftests/bpf: track tcp payload offset as scalar in xdp_synproxy
  selftests/bpf: Add netkit to tc_redirect selftest
  selftests/bpf: De-veth-ize the tc_redirect test case
  bpf, netkit: Add indirect call wrapper for fetching peer dev
  bpf: Fix dev's rx stats for bpf_redirect_peer traffic
  veth: Use tstats per-CPU traffic counters
  netkit: Add tstats per-CPU traffic counters
  net: Move {l,t,d}stats allocation to core and convert veth & vrf
  net, vrf: Move dstats structure to core
====================

Link: https://lore.kernel.org/r/20231121193113.11796-1-daniel@iogearbox.netSigned-off-by: Jakub Kicinski <kuba@kernel.org>

There has been more than a few threads which went idle before
the merge window and now people came back to them and started
asking about next steps.

We currently tell people to be patient and not to repost too
often. Our "not too often", however, is still a few orders of
magnitude faster than other subsystems. Or so I feel after
hearing people talk about review rates at LPC.

Clarify in the doc that if the discussion went idle for a week
on netdev, 95% of the time there's no point waiting longer.

Link: https://lore.kernel.org/r/20231120200109.620392-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
    - power on
    - check logs
    - shutdown
    - after detecting the system shutdown, disconnect power
    - after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
    kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
    kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
    ...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.

In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.

It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.

Fixes: e2ca90c2 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Merge tag 'platform-drivers-x86-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86

Pull x86 platform drivers fixes from Ilpo Järvinen:
 "Just a few fixes (one with two non-fix deps) plus tidying up
  MAINTAINERS"

* tag 'platform-drivers-x86-v6.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
  platform/x86: intel_telemetry: Fix kernel doc descriptions
  MAINTAINERS: Drop Mark Gross as maintainer for x86 platform drivers
  platform/x86/amd/pmc: adjust getting DRAM size behavior
  platform/x86: hp-bioscfg: Remove unused obj in hp_add_other_attributes()
  platform/x86: hp-bioscfg: Fix error handling in hp_add_other_attributes()
  platform/x86: hp-bioscfg: move mutex_lock() down in hp_add_other_attributes()
  platform/x86: hp-bioscfg: Simplify return check in hp_add_other_attributes()
  platform/x86: ideapad-laptop: Set max_brightness before using it
  MAINTAINERS: Remove stale entry for SBL platform driver

Pull erofs fixes from Gao Xiang:

 - Tidy up erofs_read_inode() for simplicity

 - Fix broken fscache mode due to NULL dereference of dif->bdev_handle

 - Add the EROFS webpage to MAINTAINERS, documentation, and Kconfig

* tag 'erofs-for-6.7-rc3-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  MAINTAINERS: erofs: add EROFS webpage
  erofs: fix NULL dereference of dif->bdev_handle in fscache mode
  erofs: simplify erofs_read_inode()

indirect_call_wrapper.h  is not, strictly speaking, networking specific.
However, it's git history indicates that in practice changes go through
netdev and thus the netdev maintainers have effectively been taking
responsibility for it.

Formalise this by adding it to the NETWORKING [GENERAL] section in the
MAINTAINERS file.

It is not clear how many other files under include/linux fall into this
category and it would be interesting, as a follow-up, to audit that and
propose further updates to the MAINTAINERS file as appropriate.

Link: https://lore.kernel.org/netdev/20231116010310.4664dd38@kernel.org/Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231120-indirect_call_wrapper-maintainer-v1-1-0a6bb1f7363e@kernel.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This reverts commit 9d1bd934.

Multiple people reported misbehaving devices and reverting this commit fixes
the problem for them. As soon as the original commit author starts reacting
again, we can try to figure out why he hasn't seen the issues (mismatching
report descriptors?), but for the time being, fix for 6.7 by reverting.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=218172
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218094

Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Haiyang Zhang says:

====================
hv_netvsc: fix race of netvsc, VF register, and slave bit

There are some races between netvsc probe, set notifier, VF register,
and slave bit setting.
This patch set fixes them.
====================

Link: https://lore.kernel.org/r/1700411023-14317-1-git-send-email-haiyangz@microsoft.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When a VF is being exposed form the kernel, it should be marked as "slave"
before exposing to the user-mode. The VF is not usable without netvsc
running as master. The user-mode should never see a VF without the "slave"
flag.

This commit moves the code of setting the slave flag to the time before
VF is exposed to user-mode.

Cc: stable@vger.kernel.org
Fixes: 0c195567 ("netvsc: transparent VF management")
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>