[ Upstream commit 08ca8b21 ]

When a subrequest is being detached from the subgroup, we want to
ensure that it is not holding the group lock, or in the process
of waiting for the group lock.

Fixes: 5b2b5187 ("NFS: Fix nfs_page_group_destroy() and nfs_lock_and_join_requests() race cases")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 8edf5332 ]

Without this commit, a PCIe hotplug port can stop generating interrupts on
hotplug events, so device adds and removals will not be seen:

The pciehp interrupt handler pciehp_isr() reads the Slot Status register
and then writes back to it to clear the bits that caused the interrupt.  If
a different interrupt event bit gets set between the read and the write,
pciehp_isr() returns without having cleared all of the interrupt event
bits.  If this happens when the MSI isn't masked (which by default it isn't
in handle_edge_irq(), and which it will never be when MSI per-vector
masking is not supported), we won't get any more hotplug interrupts from
that device.

That is expected behavior, according to the PCIe Base Spec r5.0, section
6.7.3.4, "Software Notification of Hot-Plug Events".

Because the Presence Detect Changed and Data Link Layer State Changed event
bits can both get set at nearly the same time when a device is added or
removed, this is more likely to happen than it might seem.  The issue was
found (and can be reproduced rather easily) by connecting and disconnecting
an NVMe storage device on at least one system model where the NVMe devices
were being connected to an AMD PCIe port (PCI device 0x1022/0x1483).

Fix the issue by modifying pciehp_isr() to loop back and re-read the Slot
Status register immediately after writing to it, until it sees that all of
the event status bits have been cleared.

[lukas: drop loop count limitation, write "events" instead of "status",
don't loop back in INTx and poll modes, tweak code comment & commit msg]
Link: https://lore.kernel.org/r/78b4ced5072bfe6e369d20e8b47c279b8c7af12e.1582121613.git.lukas@wunner.deTested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 5c6cd702 ]

The Miditech MIDIFACE 16x16 (USB ID 1290:1749) has more than one extra
endpoint descriptor.

The first extra descriptor is: 0x06 0x30 0x00 0x00 0x00 0x00

As the code in snd_usbmidi_get_ms_info() looks only at the
first extra descriptor to find USB_DT_CS_ENDPOINT the device
as such is recognized but there is neither input nor output
configured.

The patch iterates through the extra descriptors to find the
proper one. With this patch the device is correctly configured.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Link: https://lore.kernel.org/r/1c3b431a86f69e1d60745b6110cdb93c299f120b.camel@domdv.deSigned-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit acc5af3e ]

In “ubifs_check_node”, when the value of "node_len" is abnormal,
the code will goto label of "out_len" for execution. Then, in the
following "ubifs_dump_node", if inode type is "UBIFS_DATA_NODE",
in "print_hex_dump", an out-of-bounds access may occur due to the
wrong "ch->len".

Therefore, when the value of "node_len" is abnormal, data length
should to be adjusted to a reasonable safe range. At this time,
structured data is not credible, so dump the corrupted data directly
for analysis.
Signed-off-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 72e0ef0e ]

On some EFI systems, the video BIOS is provided by the EFI firmware.  The
boot stub code stores the physical address of the ROM image in pdev->rom.
Currently we attempt to access this pointer using phys_to_virt(), which
doesn't work with CONFIG_HIGHMEM.

On these systems, attempting to load the radeon module on a x86_32 kernel
can result in the following:

  BUG: unable to handle page fault for address: 3e8ed03c
  #PF: supervisor read access in kernel mode
  #PF: error_code(0x0000) - not-present page
  *pde = 00000000
  Oops: 0000 [#1] PREEMPT SMP
  CPU: 0 PID: 317 Comm: systemd-udevd Not tainted 5.6.0-rc3-next-20200228 #2
  Hardware name: Apple Computer, Inc. MacPro1,1/Mac-F4208DC8, BIOS     MP11.88Z.005C.B08.0707021221 07/02/07
  EIP: radeon_get_bios+0x5ed/0xe50 [radeon]
  Code: 00 00 84 c0 0f 85 12 fd ff ff c7 87 64 01 00 00 00 00 00 00 8b 47 08 8b 55 b0 e8 1e 83 e1 d6 85 c0 74 1a 8b 55 c0 85 d2 74 13 <80> 38 55 75 0e 80 78 01 aa 0f 84 a4 03 00 00 8d 74 26 00 68 dc 06
  EAX: 3e8ed03c EBX: 00000000 ECX: 3e8ed03c EDX: 00010000
  ESI: 00040000 EDI: eec04000 EBP: eef3fc60 ESP: eef3fbe0
  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010206
  CR0: 80050033 CR2: 3e8ed03c CR3: 2ec77000 CR4: 000006d0
  Call Trace:
   r520_init+0x26/0x240 [radeon]
   radeon_device_init+0x533/0xa50 [radeon]
   radeon_driver_load_kms+0x80/0x220 [radeon]
   drm_dev_register+0xa7/0x180 [drm]
   radeon_pci_probe+0x10f/0x1a0 [radeon]
   pci_device_probe+0xd4/0x140

Fix the issue by updating all drivers which can access a platform provided
ROM. Instead of calling the helper function pci_platform_rom() which uses
phys_to_virt(), call ioremap() directly on the pdev->rom.

radeon_read_platform_bios() previously directly accessed an __iomem
pointer. Avoid this by calling memcpy_fromio() instead of kmemdup().

pci_platform_rom() now has no remaining callers, so remove it.

Link: https://lore.kernel.org/r/20200319021623.5426-1-mikel@mikelr.comSigned-off-by: Mikel Rychliski <mikel@mikelr.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1a33d8a2 ]

Kernel memory leak detected:

unreferenced object 0xffff888849cdf480 (size 8):
  comm "kworker/u8:3", pid 2086, jiffies 4297898756 (age 4269.856s)
  hex dump (first 8 bytes):
    30 00 cd 49 88 88 ff ff                          0..I....
  backtrace:
    [<00000000acfc370b>] __kmalloc_track_caller+0x137/0x183
    [<00000000a2724354>] kstrdup+0x2b/0x43
    [<0000000082964f84>] xprt_rdma_format_addresses+0x114/0x17d [rpcrdma]
    [<00000000dfa6ed00>] xprt_setup_rdma_bc+0xc0/0x10c [rpcrdma]
    [<0000000073051a83>] xprt_create_transport+0x3f/0x1a0 [sunrpc]
    [<0000000053531a8e>] rpc_create+0x118/0x1cd [sunrpc]
    [<000000003a51b5f8>] setup_callback_client+0x1a5/0x27d [nfsd]
    [<000000001bd410af>] nfsd4_process_cb_update.isra.7+0x16c/0x1ac [nfsd]
    [<000000007f4bbd56>] nfsd4_run_cb_work+0x4c/0xbd [nfsd]
    [<0000000055c5586b>] process_one_work+0x1b2/0x2fe
    [<00000000b1e3e8ef>] worker_thread+0x1a6/0x25a
    [<000000005205fb78>] kthread+0xf6/0xfb
    [<000000006d2dc057>] ret_from_fork+0x3a/0x50

Introduce a call to xprt_rdma_free_addresses() similar to the way
that the TCP backchannel releases a transport's peer address
strings.

Fixes: 5d252f90 ("svcrdma: Add class for RDMA backwards direction transport")
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit b25b60d7 ]

'maxlen' is the total size of the destination buffer. There is only one
caller and this value is 256.

When we compute the size already used and what we would like to add in
the buffer, the trailling NULL character is not taken into account.
However, this trailling character will be added by the 'strcat' once we
have checked that we have enough place.

So, there is a off-by-one issue and 1 byte of the stack could be
erroneously overwridden.

Take into account the trailling NULL, when checking if there is enough
place in the destination buffer.

While at it, also replace a 'sprintf' by a safer 'snprintf', check for
output truncation and avoid a superfluous 'strlen'.

Fixes: dc9a16e4 ("svc: Add /proc/sys/sunrpc/transport files")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[ cel: very minor fix to documenting comment
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3e16e83a ]

Correct race condition where ioaccel is re-enabled before the raid_map is
updated. For RAID_1, RAID_1ADM, and RAID 5/6 there is a BUG_ON called which
is bad.

 - Change event thread to disable ioaccel only. Send all requests down the
   RAID path instead.

 - Have rescan thread handle offload_enable.

 - Since there is only one rescan allowed at a time, turning
   offload_enabled on/off should not be racy. Each handler queues up a
   rescan if one is already in progress.

  - For timing diagram, offload_enabled is initially off due to a change
    (transformation: splitmirror/remirror), ...

  otbe = offload_to_be_enabled
  oe   = offload_enabled

  Time Event         Rescan              Completion     Request
       Worker        Worker              Thread         Thread
  ---- ------        ------              ----------     -------
   T0   |             |                       + UA      |
   T1   |             + rescan started        | 0x3f    |
   T2   + Event       |                       | 0x0e    |
   T3   + Ack msg     |                       |         |
   T4   |             + if (!dev[i]->oe &&    |         |
   T5   |             |     dev[i]->otbe)     |         |
   T6   |             |      get_raid_map     |         |
   T7   + otbe = 1    |                       |         |
   T8   |             |                       |         |
   T9   |             + oe = otbe             |         |
   T10  |             |                       |         + ioaccel request
   T11                                                  * BUG_ON

  T0 - I/O completion with UA 0x3f 0x0e sets rescan flag.
  T1 - rescan worker thread starts a rescan.
  T2 - event comes in
  T3 - event thread starts and issues "Acknowledge" message
  ...
  T6 - rescan thread has bypassed code to reload new raid map.
  ...
  T7 - event thread runs and sets offload_to_be_enabled
  ...
  T9 - rescan thread turns on offload_enabled.
  T10- request comes in and goes down ioaccel path.
  T11- BUG_ON.

 - After the patch is applied, ioaccel_enabled can only be re-enabled in
   the re-scan thread.

Link: https://lore.kernel.org/r/158472877894.14200.7077843399036368335.stgit@brunhildaReviewed-by: Scott Teel <scott.teel@microsemi.com>
Reviewed-by: Matt Perricone <matt.perricone@microsemi.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d0ca2c35 ]

The RXE driver doesn't set sys_image_guid and user space applications see
zeros. This causes to pyverbs tests to fail with the following traceback,
because the IBTA spec requires to have valid sys_image_guid.

 Traceback (most recent call last):
   File "./tests/test_device.py", line 51, in test_query_device
     self.verify_device_attr(attr)
   File "./tests/test_device.py", line 74, in verify_device_attr
     assert attr.sys_image_guid != 0

In order to fix it, set sys_image_guid to be equal to node_guid.

Before:
 5: rxe0: ... node_guid 5054:00ff:feaa:5363 sys_image_guid
 0000:0000:0000:0000

After:
 5: rxe0: ... node_guid 5054:00ff:feaa:5363 sys_image_guid
 5054:00ff:feaa:5363

Fixes: 8700e3e7 ("Soft RoCE driver")
Link: https://lore.kernel.org/r/20200323112800.1444784-1-leon@kernel.orgSigned-off-by: Zhu Yanjun <yanjunz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit ce151813 ]

Calling nvme_sysfs_delete() when the controller is in the middle of
creation may cause several bugs. If the controller is in NEW state we
remove delete_controller file and don't delete the controller. The user
will not be able to use nvme disconnect command on that controller again,
although the controller may be active. Other bugs may happen if the
controller is in the middle of create_ctrl callback and
nvme_do_delete_ctrl() starts. For example, freeing I/O tagset at
nvme_do_delete_ctrl() before it was allocated at create_ctrl callback.

To fix all those races don't allow the user to delete the controller
before it was fully created.
Signed-off-by: Israel Rukshin <israelr@mellanox.com>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 764e9332 ]

The nvme multipath error handling defaults to controller reset if the
error is unknown. There are, however, no existing nvme status codes that
indicate a reset should be used, and resetting causes unnecessary
disruption to the rest of IO.

Change nvme's error handling to first check if failover should happen.
If not, let the normal error handling take over rather than reset the
controller.
Based-on-a-patch-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: John Meneghini <johnm@netapp.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d1ee7e1f ]

If '-o' was used more than 64 times in a single invocation of gpio-hammer,
this could lead to an overflow of the 'lines' array. This commit fixes
this by avoiding the overflow and giving a proper diagnostic back to the
user
Signed-off-by: Gabriel Ravier <gabravier@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d95fe371 ]

The patch avoids allocating cpufreq_policy on stack hence fixing frame
size overflow in 'powernv_cpufreq_work_fn'

Fixes: 22794280 ("cpufreq: powernv: Restore cpu frequency to policy->cur on unthrottling")
Signed-off-by: Pratik Rajesh Sampat <psampat@linux.ibm.com>
Reviewed-by: Daniel Axtens <dja@axtens.net>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200316135743.57735-1-psampat@linux.ibm.comSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d74b181a ]

'snprintf' returns the number of characters which would be generated for
the given input.

If the returned value is *greater than* or equal to the buffer size, it
means that the output has been truncated.

Fix the overflow test accordingly.

Fixes: 7780c25b ("perf tools: Allow ability to map cpus to nodes easily")
Fixes: 92a7e127 ("perf cpumap: Add cpu__max_present_cpu()")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Don Zickus <dzickus@redhat.com>
Cc: He Zhe <zhe.he@windriver.com>
Cc: Jan Stancek <jstancek@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: kernel-janitors@vger.kernel.org
Link: http://lore.kernel.org/lkml/20200324070319.10901-1-christophe.jaillet@wanadoo.frSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 7cf4df30 ]

Terminate and flush DMA internal buffers, before pushing RX data to
higher layer. Otherwise, this will lead to data corruption, as driver
would end up pushing stale buffer data to higher layer while actual data
is still stuck inside DMA hardware and has yet not arrived at the
memory.
While at that, replace deprecated dmaengine_terminate_all() with
dmaengine_terminate_async().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319110344.21348-2-vigneshr@ti.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 4ce35a36 ]

When booting j721e the following bug is printed:

[    1.154821] BUG: sleeping function called from invalid context at kernel/sched/completion.c:99
[    1.154827] in_atomic(): 0, irqs_disabled(): 128, non_block: 0, pid: 12, name: kworker/0:1
[    1.154832] 3 locks held by kworker/0:1/12:
[    1.154836]  #0: ffff000840030728 ((wq_completion)events){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154852]  #1: ffff80001214fdd8 (deferred_probe_work){+.+.}, at: process_one_work+0x1d4/0x6e8
[    1.154860]  #2: ffff00084060b170 (&dev->mutex){....}, at: __device_attach+0x38/0x138
[    1.154872] irq event stamp: 63096
[    1.154881] hardirqs last  enabled at (63095): [<ffff800010b74318>] _raw_spin_unlock_irqrestore+0x70/0x78
[    1.154887] hardirqs last disabled at (63096): [<ffff800010b740d8>] _raw_spin_lock_irqsave+0x28/0x80
[    1.154893] softirqs last  enabled at (62254): [<ffff800010080c88>] _stext+0x488/0x564
[    1.154899] softirqs last disabled at (62247): [<ffff8000100fdb3c>] irq_exit+0x114/0x140
[    1.154906] CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.6.0-rc6-next-20200318-00094-g45e4089b0bd3 #221
[    1.154911] Hardware name: Texas Instruments K3 J721E SoC (DT)
[    1.154917] Workqueue: events deferred_probe_work_func
[    1.154923] Call trace:
[    1.154928]  dump_backtrace+0x0/0x190
[    1.154933]  show_stack+0x14/0x20
[    1.154940]  dump_stack+0xe0/0x148
[    1.154946]  ___might_sleep+0x150/0x1f0
[    1.154952]  __might_sleep+0x4c/0x80
[    1.154957]  wait_for_completion_timeout+0x40/0x140
[    1.154964]  ti_sci_set_device_state+0xa0/0x158
[    1.154969]  ti_sci_cmd_get_device_exclusive+0x14/0x20
[    1.154977]  ti_sci_dev_start+0x34/0x50
[    1.154984]  genpd_runtime_resume+0x78/0x1f8
[    1.154991]  __rpm_callback+0x3c/0x140
[    1.154996]  rpm_callback+0x20/0x80
[    1.155001]  rpm_resume+0x568/0x758
[    1.155007]  __pm_runtime_resume+0x44/0xb0
[    1.155013]  omap8250_probe+0x2b4/0x508
[    1.155019]  platform_drv_probe+0x50/0xa0
[    1.155023]  really_probe+0xd4/0x318
[    1.155028]  driver_probe_device+0x54/0xe8
[    1.155033]  __device_attach_driver+0x80/0xb8
[    1.155039]  bus_for_each_drv+0x74/0xc0
[    1.155044]  __device_attach+0xdc/0x138
[    1.155049]  device_initial_probe+0x10/0x18
[    1.155053]  bus_probe_device+0x98/0xa0
[    1.155058]  deferred_probe_work_func+0x74/0xb0
[    1.155063]  process_one_work+0x280/0x6e8
[    1.155068]  worker_thread+0x48/0x430
[    1.155073]  kthread+0x108/0x138
[    1.155079]  ret_from_fork+0x10/0x18

To fix the bug we need to first call pm_runtime_enable() prior to any
pm_runtime calls.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200320125200.6772-1-peter.ujfalusi@ti.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f19c3f6c ]

When port's throttle callback is called, it should stop pushing any more
data into TTY buffer to avoid buffer overflow. This means driver has to
stop HW from receiving more data and assert the HW flow control. For
UARTs with auto HW flow control (such as 8250_omap) manual assertion of
flow control line is not possible and only way is to allow RX FIFO to
fill up, thus trigger auto HW flow control logic.

Therefore make sure that 8250 generic IRQ handler does not drain data
when port is stopped (i.e UART_LSR_DR is unset in read_status_mask). Not
servicing, RX FIFO would trigger auto HW flow control when FIFO
occupancy reaches preset threshold, thus halting RX.
Since, error conditions in UART_LSR register are cleared just by reading
the register, data has to be drained in case there are FIFO errors, else
error information will lost.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200319103230.16867-2-vigneshr@ti.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d4953f7e ]

Reproducible with a clang asan build and then running perf test in
particular 'Parse event definition strings'.
Signed-off-by: Ian Rogers <irogers@google.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Leo Yan <leo.yan@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: clang-built-linux@googlegroups.com
Link: http://lore.kernel.org/lkml/20200314170356.62914-1-irogers@google.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 39056e8a ]

If the common register memory resource is not available the driver needs
to fail gracefully to disable PM. Instead of returning the error
directly store it in ret and use the already existing error path.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200310114709.1483860-1-niklas.soderlund+renesas@ragnatech.seSigned-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bf2cbe04 ]

Clang warns:

../kernel/trace/trace.c:9335:33: warning: array comparison always
evaluates to true [-Wtautological-compare]
        if (__stop___trace_bprintk_fmt != __start___trace_bprintk_fmt)
                                       ^
1 warning generated.

These are not true arrays, they are linker defined symbols, which are
just addresses. Using the address of operator silences the warning and
does not change the runtime result of the check (tested with some print
statements compiled in with clang + ld.lld and gcc + ld.bfd in QEMU).

Link: http://lkml.kernel.org/r/20200220051011.26113-1-natechancellor@gmail.com

Link: https://github.com/ClangBuiltLinux/linux/issues/893Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 0478b4fc ]

If the opp table specifies opp-supported-hw as a property but the driver
has not set a supported hardware value the OPP subsystem will reject
all the table entries.

Set a "default" value that will match the default table entries but not
conflict with any possible real bin values. Also fix a small memory leak
and free the buffer allocated by nvmem_cell_read().
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 66be340f ]

We should free resources in unlikely case of allocation failure.
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1dff3064 ]

On P9 DD2.2 due to a CPU defect some TM instructions need to be emulated by
KVM. This is handled at first by the hardware raising a softpatch interrupt
when certain TM instructions that need KVM assistance are executed in the
guest. Althought some TM instructions per Power ISA are invalid forms they
can raise a softpatch interrupt too. For instance, 'tresume.' instruction
as defined in the ISA must have bit 31 set (1), but an instruction that
matches 'tresume.' PO and XO opcode fields but has bit 31 not set (0), like
0x7cfe9ddc, also raises a softpatch interrupt. Similarly for 'treclaim.'
and 'trechkpt.' instructions with bit 31 = 0, i.e. 0x7c00075c and
0x7c0007dc, respectively. Hence, if a code like the following is executed
in the guest it will raise a softpatch interrupt just like a 'tresume.'
when the TM facility is enabled ('tabort. 0' in the example is used only
to enable the TM facility):

int main() { asm("tabort. 0; .long 0x7cfe9ddc;"); }

Currently in such a case KVM throws a complete trace like:

[345523.705984] WARNING: CPU: 24 PID: 64413 at arch/powerpc/kvm/book3s_hv_tm.c:211 kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.705985] Modules linked in: kvm_hv(E) xt_conntrack ipt_REJECT nf_reject_ipv4 xt_tcpudp ip6table_mangle ip6table_nat
iptable_mangle iptable_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ebtable_filter ebtables ip6table_filter
ip6_tables iptable_filter bridge stp llc sch_fq_codel ipmi_powernv at24 vmx_crypto ipmi_devintf ipmi_msghandler
ibmpowernv uio_pdrv_genirq kvm opal_prd uio leds_powernv ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp
libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs blake2b_generic zstd_compress raid10 raid456
async_raid6_recov async_memcpy async_pq async_xor async_tx libcrc32c xor raid6_pq raid1 raid0 multipath linear tg3
crct10dif_vpmsum crc32c_vpmsum ipr [last unloaded: kvm_hv]
[345523.706030] CPU: 24 PID: 64413 Comm: CPU 0/KVM Tainted: G        W   E     5.5.0+ #1
[345523.706031] NIP:  c0080000072cb9c0 LR: c0080000072b5e80 CTR: c0080000085c7850
[345523.706034] REGS: c000000399467680 TRAP: 0700   Tainted: G        W   E      (5.5.0+)
[345523.706034] MSR:  900000010282b033 <SF,HV,VEC,VSX,EE,FP,ME,IR,DR,RI,LE,TM[E]>  CR: 24022428  XER: 00000000
[345523.706042] CFAR: c0080000072b5e7c IRQMASK: 0
                GPR00: c0080000072b5e80 c000000399467910 c0080000072db500 c000000375ccc720
                GPR04: c000000375ccc720 00000003fbec0000 0000a10395dda5a6 0000000000000000
                GPR08: 000000007cfe9ddc 7cfe9ddc000005dc 7cfe9ddc7c0005dc c0080000072cd530
                GPR12: c0080000085c7850 c0000003fffeb800 0000000000000001 00007dfb737f0000
                GPR16: c0002001edcca558 0000000000000000 0000000000000000 0000000000000001
                GPR20: c000000001b21258 c0002001edcca558 0000000000000018 0000000000000000
                GPR24: 0000000001000000 ffffffffffffffff 0000000000000001 0000000000001500
                GPR28: c0002001edcc4278 c00000037dd80000 800000050280f033 c000000375ccc720
[345523.706062] NIP [c0080000072cb9c0] kvmhv_p9_tm_emulation+0x68/0x620 [kvm_hv]
[345523.706065] LR [c0080000072b5e80] kvmppc_handle_exit_hv.isra.53+0x3e8/0x798 [kvm_hv]
[345523.706066] Call Trace:
[345523.706069] [c000000399467910] [c000000399467940] 0xc000000399467940 (unreliable)
[345523.706071] [c000000399467950] [c000000399467980] 0xc000000399467980
[345523.706075] [c0000003994679f0] [c0080000072bd1c4] kvmhv_run_single_vcpu+0xa1c/0xb80 [kvm_hv]
[345523.706079] [c000000399467ac0] [c0080000072bd8e0] kvmppc_vcpu_run_hv+0x5b8/0xb00 [kvm_hv]
[345523.706087] [c000000399467b90] [c0080000085c93cc] kvmppc_vcpu_run+0x34/0x48 [kvm]
[345523.706095] [c000000399467bb0] [c0080000085c582c] kvm_arch_vcpu_ioctl_run+0x244/0x420 [kvm]
[345523.706101] [c000000399467c40] [c0080000085b7498] kvm_vcpu_ioctl+0x3d0/0x7b0 [kvm]
[345523.706105] [c000000399467db0] [c0000000004adf9c] ksys_ioctl+0x13c/0x170
[345523.706107] [c000000399467e00] [c0000000004adff8] sys_ioctl+0x28/0x80
[345523.706111] [c000000399467e20] [c00000000000b278] system_call+0x5c/0x68
[345523.706112] Instruction dump:
[345523.706114] 419e0390 7f8a4840 409d0048 6d497c00 2f89075d 419e021c 6d497c00 2f8907dd
[345523.706119] 419e01c0 6d497c00 2f8905dd 419e00a4 <0fe00000> 38210040 38600000 ebc1fff0

and then treats the executed instruction as a 'nop'.

However the POWER9 User's Manual, in section "4.6.10 Book II Invalid
Forms", informs that for TM instructions bit 31 is in fact ignored, thus
for the TM-related invalid forms ignoring bit 31 and handling them like the
valid forms is an acceptable way to handle them. POWER8 behaves the same
way too.

This commit changes the handling of the cases here described by treating
the TM-related invalid forms that can generate a softpatch interrupt
just like their valid forms (w/ bit 31 = 1) instead of as a 'nop' and by
gently reporting any other unrecognized case to the host and treating it as
illegal instruction instead of throwing a trace and treating it as a 'nop'.
Signed-off-by: Gustavo Romero <gromero@linux.ibm.com>
Reviewed-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-By: Michael Neuling <mikey@neuling.org>
Reviewed-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bede86a3 ]

When creating a cm_id during REQ the id immediately becomes visible to the
other MAD handlers, and shortly after the state is moved to IB_CM_REQ_RCVD

This allows cm_rej_handler() to run concurrently and free the work:

        CPU 0                                CPU1
 cm_req_handler()
  ib_create_cm_id()
  cm_match_req()
    id_priv->state = IB_CM_REQ_RCVD
                                       cm_rej_handler()
                                         cm_acquire_id()
                                         spin_lock(&id_priv->lock)
                                         switch (id_priv->state)
  					   case IB_CM_REQ_RCVD:
                                            cm_reset_to_idle()
                                             kfree(id_priv->timewait_info);
   goto destroy
  destroy:
    kfree(id_priv->timewait_info);
                                             id_priv->timewait_info = NULL

Causing a double free or worse.

Do not free the timewait_info without also holding the
id_priv->lock. Simplify this entire flow by making the free unconditional
during cm_destroy_id() and removing the confusing special case error
unwind during creation of the timewait_info.

This also fixes a leak of the timewait if cm_destroy_id() is called in
IB_CM_ESTABLISHED with an XRC TGT QP. The state machine will be left in
ESTABLISHED while it needed to transition through IB_CM_TIMEWAIT to
release the timewait pointer.

Also fix a leak of the timewait_info if the caller mis-uses the API and
does ib_send_cm_reqs().

Fixes: a977049d ("[PATCH] IB: Add the kernel CM implementation")
Link: https://lore.kernel.org/r/20200310092545.251365-4-leon@kernel.orgSigned-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a451b123 ]

In NFSv4, the lock stateids are tied to the lockowner, and the open stateid,
so that the action of closing the file also results in either an automatic
loss of the locks, or an error of the form NFS4ERR_LOCKS_HELD.

In practice this means we must not add new locks to the open stateid
after the close process has been invoked. In fact doing so, can result
in the following panic:

 kernel BUG at lib/list_debug.c:51!
 invalid opcode: 0000 [#1] SMP NOPTI
 CPU: 2 PID: 1085 Comm: nfsd Not tainted 5.6.0-rc3+ #2
 Hardware name: VMware, Inc. VMware7,1/440BX Desktop Reference Platform, BIOS VMW71.00V.14410784.B64.1908150010 08/15/2019
 RIP: 0010:__list_del_entry_valid.cold+0x31/0x55
 Code: 1a 3d 9b e8 74 10 c2 ff 0f 0b 48 c7 c7 f0 1a 3d 9b e8 66 10 c2 ff 0f 0b 48 89 f2 48 89 fe 48 c7 c7 b0 1a 3d 9b e8 52 10 c2 ff <0f> 0b 48 89 fe 4c 89 c2 48 c7 c7 78 1a 3d 9b e8 3e 10 c2 ff 0f 0b
 RSP: 0018:ffffb296c1d47d90 EFLAGS: 00010246
 RAX: 0000000000000054 RBX: ffff8ba032456ec8 RCX: 0000000000000000
 RDX: 0000000000000000 RSI: ffff8ba039e99cc8 RDI: ffff8ba039e99cc8
 RBP: ffff8ba032456e60 R08: 0000000000000781 R09: 0000000000000003
 R10: 0000000000000000 R11: 0000000000000001 R12: ffff8ba009a4abe0
 R13: ffff8ba032456e8c R14: 0000000000000000 R15: ffff8ba00adb01d8
 FS:  0000000000000000(0000) GS:ffff8ba039e80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007fb213f0b008 CR3: 00000001347de006 CR4: 00000000003606e0
 Call Trace:
  release_lock_stateid+0x2b/0x80 [nfsd]
  nfsd4_free_stateid+0x1e9/0x210 [nfsd]
  nfsd4_proc_compound+0x414/0x700 [nfsd]
  ? nfs4svc_decode_compoundargs+0x407/0x4c0 [nfsd]
  nfsd_dispatch+0xc1/0x200 [nfsd]
  svc_process_common+0x476/0x6f0 [sunrpc]
  ? svc_sock_secure_port+0x12/0x30 [sunrpc]
  ? svc_recv+0x313/0x9c0 [sunrpc]
  ? nfsd_svc+0x2d0/0x2d0 [nfsd]
  svc_process+0xd4/0x110 [sunrpc]
  nfsd+0xe3/0x140 [nfsd]
  kthread+0xf9/0x130
  ? nfsd_destroy+0x50/0x50 [nfsd]
  ? kthread_park+0x90/0x90
  ret_from_fork+0x1f/0x40

The fix is to ensure that lock creation tests for whether or not the
open stateid is unhashed, and to fail if that is the case.

Fixes: 659aefb6 ("nfsd: Ensure we don't recognise lock stateids after freeing them")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c11af813 ]

The RTC IRQ is requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.

To fix this issue, allocating the rtc_device struct before requesting
the RTC IRQ using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.

Link: https://lore.kernel.org/r/20200306073404.56921-1-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit f2997775 ]

Both RTC IRQs are requested before the struct rtc_device is allocated,
this may lead to a NULL pointer dereference in the IRQ handler.

To fix this issue, allocating the rtc_device struct before requesting
the IRQs using devm_rtc_allocate_device, and use rtc_register_device
to register the RTC device.

Link: https://lore.kernel.org/r/20200306010146.39762-1-alexandre.belloni@bootlin.comSigned-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit d8d74ea3 ]

Synchronize with the results from the CRQs before continuing with
the initialization. This avoids trying to send TPM commands while
the rtce buffer has not been allocated, yet.

This patch fixes an existing race condition that may occurr if the
hypervisor does not quickly respond to the VTPM_GET_RTCE_BUFFER_SIZE
request sent during initialization and therefore the ibmvtpm->rtce_buf
has not been allocated at the time the first TPM command is sent.

Fixes: 132f7629 ("drivers/char/tpm: Add new device driver to support IBM vTPM")
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Nayna Jain <nayna@linux.ibm.com>
Tested-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit eb576086 ]

We already has similar code in ext4_mb_complex_scan_group(), but
ext4_mb_simple_scan_group() still affected.

Other reports: https://www.spinics.net/lists/linux-ext4/msg60231.htmlReviewed-by: Andreas Dilger <adilger@dilger.ca>
Signed-off-by: Dmitry Monakhov <dmonakhov@gmail.com>
Link: https://lore.kernel.org/r/20200310150156.641-1-dmonakhov@gmail.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 2e107cf8 ]

In xchk_dir_actor, we attempt to validate the directory hash structures
by performing a directory entry lookup by (hashed) name.  If the lookup
returns ENOENT, that means that the hash information is corrupt.  The
_process_error functions don't catch this, so we have to add that
explicitly.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1cb5deb5 ]

If we decide that a directory free block is corrupt, we must take care
not to leak a buffer pointer to the caller.  After xfs_trans_brelse
returns, the buffer can be freed or reused, which means that we have to
set *bpp back to NULL.

Callers are supposed to notice the nonzero return value and not use the
buffer pointer, but we should code more defensively, even if all current
callers handle this situation correctly.

Fixes: de14c5f5 ("xfs: verify free block header fields")
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a7463e2d ]

The shifting of buf[3] by 24 bits to the left will be promoted to
a 32 bit signed int and then sign-extended to an unsigned long. In
the unlikely event that the the top bit of buf[3] is set then all
then all the upper bits end up as also being set because of
the sign-extension and this affect the ev->post_bit_error sum.
Fix this by using the temporary u32 variable bit_error to avoid
the sign-extension promotion. This also removes the need to do the
computation twice.

Addresses-Coverity: ("Unintended sign extension")

Fixes: 267897a4 ("[media] tda10071: implement DVBv5 statistics")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 96298f64 ]

According to Core Spec Version 5.2 | Vol 3, Part A 6.1.5,
the incoming L2CAP_ConfigReq should be handled during
OPEN state.

The section below shows the btmon trace when running
L2CAP/COS/CFD/BV-12-C before and after this change.

=== Before ===
...
> ACL Data RX: Handle 256 flags 0x02 dlen 12                #22
      L2CAP: Connection Request (0x02) ident 2 len 4
        PSM: 1 (0x0001)
        Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16                #23
      L2CAP: Connection Response (0x03) ident 2 len 8
        Destination CID: 64
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12                #24
      L2CAP: Configure Request (0x04) ident 2 len 4
        Destination CID: 65
        Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5      #25
        Num handles: 1
        Handle: 256
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5      #26
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 16                #27
      L2CAP: Configure Request (0x04) ident 3 len 8
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00                                            ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18                #28
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
> HCI Event: Number of Completed Packets (0x13) plen 5      #29
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 14                #30
      L2CAP: Configure Response (0x05) ident 2 len 6
        Source CID: 64
        Flags: 0x0000
        Result: Success (0x0000)
> ACL Data RX: Handle 256 flags 0x02 dlen 20                #31
      L2CAP: Configure Request (0x04) ident 3 len 12
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00 91 02 11 11                                ......
< ACL Data TX: Handle 256 flags 0x00 dlen 14                #32
      L2CAP: Command Reject (0x01) ident 3 len 6
        Reason: Invalid CID in request (0x0002)
        Destination CID: 64
        Source CID: 65
> HCI Event: Number of Completed Packets (0x13) plen 5      #33
        Num handles: 1
        Handle: 256
        Count: 1
...
=== After ===
...
> ACL Data RX: Handle 256 flags 0x02 dlen 12               #22
      L2CAP: Connection Request (0x02) ident 2 len 4
        PSM: 1 (0x0001)
        Source CID: 65
< ACL Data TX: Handle 256 flags 0x00 dlen 16               #23
      L2CAP: Connection Response (0x03) ident 2 len 8
        Destination CID: 64
        Source CID: 65
        Result: Connection successful (0x0000)
        Status: No further information available (0x0000)
< ACL Data TX: Handle 256 flags 0x00 dlen 12               #24
      L2CAP: Configure Request (0x04) ident 2 len 4
        Destination CID: 65
        Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5     #25
        Num handles: 1
        Handle: 256
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5     #26
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 16               #27
      L2CAP: Configure Request (0x04) ident 3 len 8
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00                                            ..
< ACL Data TX: Handle 256 flags 0x00 dlen 18               #28
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
> HCI Event: Number of Completed Packets (0x13) plen 5     #29
        Num handles: 1
        Handle: 256
        Count: 1
> ACL Data RX: Handle 256 flags 0x02 dlen 14               #30
      L2CAP: Configure Response (0x05) ident 2 len 6
        Source CID: 64
        Flags: 0x0000
        Result: Success (0x0000)
> ACL Data RX: Handle 256 flags 0x02 dlen 20               #31
      L2CAP: Configure Request (0x04) ident 3 len 12
        Destination CID: 64
        Flags: 0x0000
        Option: Unknown (0x10) [hint]
        01 00 91 02 11 11                                .....
< ACL Data TX: Handle 256 flags 0x00 dlen 18               #32
      L2CAP: Configure Response (0x05) ident 3 len 10
        Source CID: 65
        Flags: 0x0000
        Result: Success (0x0000)
        Option: Maximum Transmission Unit (0x01) [mandatory]
          MTU: 672
< ACL Data TX: Handle 256 flags 0x00 dlen 12               #33
      L2CAP: Configure Request (0x04) ident 3 len 4
        Destination CID: 65
        Flags: 0x0000
> HCI Event: Number of Completed Packets (0x13) plen 5     #34
        Num handles: 1
        Handle: 256
        Count: 1
> HCI Event: Number of Completed Packets (0x13) plen 5     #35
        Num handles: 1
        Handle: 256
        Count: 1
...
Signed-off-by: Howard Chung <howardchung@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit bef18d30 ]

Fixes the occasional adapter panic when sg_reset is issued with -d, -t, -b
and -H flags.  Removal of command type HBA_IU_TYPE_SCSI_TM_REQ in
aac_hba_send since iu_type, request_id and fib_flags are not populated.
Device and target reset handlers are made to send TMF commands only when
reset_state is 0.

Link: https://lore.kernel.org/r/1581553771-25796-1-git-send-email-Sagar.Biradar@microchip.comReviewed-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Signed-off-by: Sagar Biradar <Sagar.Biradar@microchip.com>
Signed-off-by: Balsundar P <balsundar.p@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 402f2992 ]

When use command to read values, it crashed.

command:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value count=1 bs=4 skip=$((0x100233))

It will call to ath10k_sdio_hif_diag_read with address = 0x4008cc and buf_len = 4.

Then system crash:
[ 1786.013258] Unable to handle kernel paging request at virtual address ffffffc00bd45000
[ 1786.013273] Mem abort info:
[ 1786.013281]   ESR = 0x96000045
[ 1786.013291]   Exception class = DABT (current EL), IL = 32 bits
[ 1786.013299]   SET = 0, FnV = 0
[ 1786.013307]   EA = 0, S1PTW = 0
[ 1786.013314] Data abort info:
[ 1786.013322]   ISV = 0, ISS = 0x00000045
[ 1786.013330]   CM = 0, WnR = 1
[ 1786.013342] swapper pgtable: 4k pages, 39-bit VAs, pgdp = 000000008542a60e
[ 1786.013350] [ffffffc00bd45000] pgd=0000000000000000, pud=0000000000000000
[ 1786.013368] Internal error: Oops: 96000045 [#1] PREEMPT SMP
[ 1786.013609] Process swapper/0 (pid: 0, stack limit = 0x0000000084b153c6)
[ 1786.013623] CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.19.86 #137
[ 1786.013631] Hardware name: MediaTek krane sku176 board (DT)
[ 1786.013643] pstate: 80000085 (Nzcv daIf -PAN -UAO)
[ 1786.013662] pc : __memcpy+0x94/0x180
[ 1786.013678] lr : swiotlb_tbl_unmap_single+0x84/0x150
[ 1786.013686] sp : ffffff8008003c60
[ 1786.013694] x29: ffffff8008003c90 x28: ffffffae96411f80
[ 1786.013708] x27: ffffffae960d2018 x26: ffffff8019a4b9a8
[ 1786.013721] x25: 0000000000000000 x24: 0000000000000001
[ 1786.013734] x23: ffffffae96567000 x22: 00000000000051d4
[ 1786.013747] x21: 0000000000000000 x20: 00000000fe6e9000
[ 1786.013760] x19: 0000000000000004 x18: 0000000000000020
[ 1786.013773] x17: 0000000000000001 x16: 0000000000000000
[ 1786.013787] x15: 00000000ffffffff x14: 00000000000044c0
[ 1786.013800] x13: 0000000000365ba4 x12: 0000000000000000
[ 1786.013813] x11: 0000000000000001 x10: 00000037be6e9000
[ 1786.013826] x9 : ffffffc940000000 x8 : 000000000bd45000
[ 1786.013839] x7 : 0000000000000000 x6 : ffffffc00bd45000
[ 1786.013852] x5 : 0000000000000000 x4 : 0000000000000000
[ 1786.013865] x3 : 0000000000000c00 x2 : 0000000000000004
[ 1786.013878] x1 : fffffff7be6e9004 x0 : ffffffc00bd45000
[ 1786.013891] Call trace:
[ 1786.013903]  __memcpy+0x94/0x180
[ 1786.013914]  unmap_single+0x6c/0x84
[ 1786.013925]  swiotlb_unmap_sg_attrs+0x54/0x80
[ 1786.013938]  __swiotlb_unmap_sg_attrs+0x8c/0xa4
[ 1786.013952]  msdc_unprepare_data+0x6c/0x84
[ 1786.013963]  msdc_request_done+0x58/0x84
[ 1786.013974]  msdc_data_xfer_done+0x1a0/0x1c8
[ 1786.013985]  msdc_irq+0x12c/0x17c
[ 1786.013996]  __handle_irq_event_percpu+0xe4/0x250
[ 1786.014006]  handle_irq_event_percpu+0x28/0x68
[ 1786.014015]  handle_irq_event+0x48/0x78
[ 1786.014026]  handle_fasteoi_irq+0xd0/0x1a0
[ 1786.014039]  __handle_domain_irq+0x84/0xc4
[ 1786.014050]  gic_handle_irq+0x124/0x1a4
[ 1786.014059]  el1_irq+0xb0/0x128
[ 1786.014072]  cpuidle_enter_state+0x298/0x328
[ 1786.014082]  cpuidle_enter+0x30/0x40
[ 1786.014094]  do_idle+0x190/0x268
[ 1786.014104]  cpu_startup_entry+0x24/0x28
[ 1786.014116]  rest_init+0xd4/0xe0
[ 1786.014126]  start_kernel+0x30c/0x38c
[ 1786.014139] Code: f8408423 f80084c3 36100062 b8404423 (b80044c3)
[ 1786.014150] ---[ end trace 3b02ddb698ea69ee ]---
[ 1786.015415] Kernel panic - not syncing: Fatal exception in interrupt
[ 1786.015433] SMP: stopping secondary CPUs
[ 1786.015447] Kernel Offset: 0x2e8d200000 from 0xffffff8008000000
[ 1786.015458] CPU features: 0x0,2188200c
[ 1786.015466] Memory Limit: none

For sdio chip, it need the memory which is kmalloc, if it is
vmalloc from ath10k_mem_value_read, then it have a memory error.
kzalloc of ath10k_sdio_hif_diag_read32 is the correct type, so
add kzalloc in ath10k_sdio_hif_diag_read to replace the buffer
which is vmalloc from ath10k_mem_value_read.

This patch only effect sdio chip.

Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit a0e40018 ]

Raven provides retimer feature support that requires i2c interaction in
order to make it work well, all settings required for this configuration
are loaded from the Atom bios which include the i2c address. If the
retimer feature is not available, we should abort the attempt to set
this feature, otherwise, it makes the following line return
I2C_CHANNEL_OPERATION_NO_RESPONSE:

 i2c_success = i2c_write(pipe_ctx, slave_address, buffer, sizeof(buffer));
 ...
 if (!i2c_success)
   ASSERT(i2c_success);

This ends up causing problems with hotplugging HDMI displays on Raven,
and causes retimer settings to warn like so:

WARNING: CPU: 1 PID: 429 at
drivers/gpu/drm/amd/amdgpu/../dal/dc/core/dc_link.c:1998
write_i2c_retimer_setting+0xc2/0x3c0 [amdgpu] Modules linked in:
edac_mce_amd ccp kvm irqbypass binfmt_misc crct10dif_pclmul crc32_pclmul
ghash_clmulni_intel snd_hda_codec_realtek snd_hda_codec_generic
ledtrig_audio snd_hda_codec_hdmi snd_hda_intel amdgpu(+) snd_hda_codec
snd_hda_core snd_hwdep snd_pcm snd_seq_midi snd_seq_midi_event
snd_rawmidi aesni_intel snd_seq amd_iommu_v2 gpu_sched aes_x86_64
crypto_simd cryptd glue_helper snd_seq_device ttm drm_kms_helper
snd_timer eeepc_wmi wmi_bmof asus_wmi sparse_keymap drm mxm_wmi snd
k10temp fb_sys_fops syscopyarea sysfillrect sysimgblt soundcore joydev
input_leds mac_hid sch_fq_codel parport_pc ppdev lp parport ip_tables
x_tables autofs4 igb i2c_algo_bit hid_generic usbhid i2c_piix4 dca ahci
hid libahci video wmi gpio_amdpt gpio_generic CPU: 1 PID: 429 Comm:
systemd-udevd Tainted: G        W         5.2.0-rc1sept162019+ #1
Hardware name: System manufacturer System Product Name/ROG STRIX B450-F
GAMING, BIOS 2605 08/06/2019
RIP: 0010:write_i2c_retimer_setting+0xc2/0x3c0 [amdgpu]
Code: ff 0f b6 4d ce 44 0f b6 45 cf 44 0f b6 c8 45 89 cf 44 89 e2 48 c7
c6 f0 34 bc c0 bf 04 00 00 00 e8 63 b0 90 ff 45 84 ff 75 02 <0f> 0b 42
0f b6 04 73 8d 50 f6 80 fa 02 77 8c 3c 0a 0f 85 c8 00 00 RSP:
0018:ffffa99d02726fd0 EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffffa99d02727035 RCX: 0000000000000006
RDX: 0000000000000000 RSI: 0000000000000002 RDI: ffff976acc857440
RBP: ffffa99d02727018 R08: 0000000000000002 R09: 000000000002a600
R10: ffffe90610193680 R11: 00000000000005e3 R12: 000000000000005d
R13: ffff976ac4b201b8 R14: 0000000000000001 R15: 0000000000000000
FS:  00007f14f99e1680(0000) GS:ffff976acc840000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fdf212843b8 CR3: 0000000408906000 CR4: 00000000003406e0
Call Trace:
 core_link_enable_stream+0x626/0x680 [amdgpu]
 dce110_apply_ctx_to_hw+0x414/0x4e0 [amdgpu]
 dc_commit_state+0x331/0x5e0 [amdgpu]
 ? drm_calc_timestamping_constants+0xf9/0x150 [drm]
 amdgpu_dm_atomic_commit_tail+0x395/0x1e00 [amdgpu]
 ? dm_plane_helper_prepare_fb+0x20c/0x280 [amdgpu]
 commit_tail+0x42/0x70 [drm_kms_helper]
 drm_atomic_helper_commit+0x10c/0x120 [drm_kms_helper]
 amdgpu_dm_atomic_commit+0x95/0xa0 [amdgpu]
 drm_atomic_commit+0x4a/0x50 [drm]
 restore_fbdev_mode_atomic+0x1c0/0x1e0 [drm_kms_helper]
 restore_fbdev_mode+0x4c/0x160 [drm_kms_helper]
 ? _cond_resched+0x19/0x40
 drm_fb_helper_restore_fbdev_mode_unlocked+0x4e/0xa0 [drm_kms_helper]
 drm_fb_helper_set_par+0x2d/0x50 [drm_kms_helper]
 fbcon_init+0x471/0x630
 visual_init+0xd5/0x130
 do_bind_con_driver+0x20a/0x430
 do_take_over_console+0x7d/0x1b0
 do_fbcon_takeover+0x5c/0xb0
 fbcon_event_notify+0x6cd/0x8a0
 notifier_call_chain+0x4c/0x70
 blocking_notifier_call_chain+0x43/0x60
 fb_notifier_call_chain+0x1b/0x20
 register_framebuffer+0x254/0x360
 __drm_fb_helper_initial_config_and_unlock+0x2c5/0x510 [drm_kms_helper]
 drm_fb_helper_initial_config+0x35/0x40 [drm_kms_helper]
 amdgpu_fbdev_init+0xcd/0x100 [amdgpu]
 amdgpu_device_init+0x1156/0x1930 [amdgpu]
 amdgpu_driver_load_kms+0x8d/0x2e0 [amdgpu]
 drm_dev_register+0x12b/0x1c0 [drm]
 amdgpu_pci_probe+0xd3/0x160 [amdgpu]
 local_pci_probe+0x47/0xa0
 pci_device_probe+0x142/0x1b0
 really_probe+0xf5/0x3d0
 driver_probe_device+0x11b/0x130
 device_driver_attach+0x58/0x60
 __driver_attach+0xa3/0x140
 ? device_driver_attach+0x60/0x60
 ? device_driver_attach+0x60/0x60
 bus_for_each_dev+0x74/0xb0
 ? kmem_cache_alloc_trace+0x1a3/0x1c0
 driver_attach+0x1e/0x20
 bus_add_driver+0x147/0x220
 ? 0xffffffffc0cb9000
 driver_register+0x60/0x100
 ? 0xffffffffc0cb9000
 __pci_register_driver+0x5a/0x60
 amdgpu_init+0x74/0x83 [amdgpu]
 do_one_initcall+0x4a/0x1fa
 ? _cond_resched+0x19/0x40
 ? kmem_cache_alloc_trace+0x3f/0x1c0
 ? __vunmap+0x1cc/0x200
 do_init_module+0x5f/0x227
 load_module+0x2330/0x2b40
 __do_sys_finit_module+0xfc/0x120
 ? __do_sys_finit_module+0xfc/0x120
 __x64_sys_finit_module+0x1a/0x20
 do_syscall_64+0x5a/0x130
 entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x7f14f9500839
Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89
f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01
f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007fff9bc4f5a8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139
RAX: ffffffffffffffda RBX: 000055afb5abce30 RCX: 00007f14f9500839
RDX: 0000000000000000 RSI: 000055afb5ace0f0 RDI: 0000000000000017
RBP: 000055afb5ace0f0 R08: 0000000000000000 R09: 000000000000000a
R10: 0000000000000017 R11: 0000000000000246 R12: 0000000000000000
R13: 000055afb5aad800 R14: 0000000000020000 R15: 0000000000000000
---[ end trace c286e96563966f08 ]---

This commit reworks the way that we handle i2c write for retimer in the
way that we abort this configuration if the feature is not available in
the device. For debug sake, we kept a simple log message in case the
retimer is not available.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 1b3460a8 ]

mitigates race condition on BACO reset between GPU bootcode and driver reload
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit c3e5ea6e ]

Jeff Moyer has reported that one of xfstests triggers a warning when run
on DAX-enabled filesystem:

	WARNING: CPU: 76 PID: 51024 at mm/memory.c:2317 wp_page_copy+0xc40/0xd50
	...
	wp_page_copy+0x98c/0xd50 (unreliable)
	do_wp_page+0xd8/0xad0
	__handle_mm_fault+0x748/0x1b90
	handle_mm_fault+0x120/0x1f0
	__do_page_fault+0x240/0xd70
	do_page_fault+0x38/0xd0
	handle_page_fault+0x10/0x30

The warning happens on failed __copy_from_user_inatomic() which tries to
copy data into a CoW page.

This happens because of race between MADV_DONTNEED and CoW page fault:

	CPU0					CPU1
 handle_mm_fault()
   do_wp_page()
     wp_page_copy()
       do_wp_page()
					madvise(MADV_DONTNEED)
					  zap_page_range()
					    zap_pte_range()
					      ptep_get_and_clear_full()
					      <TLB flush>
	 __copy_from_user_inatomic()
	 sees empty PTE and fails
	 WARN_ON_ONCE(1)
	 clear_page()

The solution is to re-try __copy_from_user_inatomic() under PTL after
checking that PTE is matches the orig_pte.

The second copy attempt can still fail, like due to non-readable PTE, but
there's nothing reasonable we can do about, except clearing the CoW page.
Reported-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Tested-by: Jeff Moyer <jmoyer@redhat.com>
Cc: <stable@vger.kernel.org>
Cc: Justin He <Justin.He@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Link: http://lkml.kernel.org/r/20200218154151.13349-1-kirill.shutemov@linux.intel.comSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit 3f5777fb ]

The memory for global pointer is never freed during normal program
execution, so let's do that in the main function exit as a good
programming practice.

A stray blank line is also removed.
Reported-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: James Clark <james.clark@arm.com>
Cc: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will@kernel.org>
Cc: linuxarm@huawei.com
Link: http://lore.kernel.org/lkml/1583406486-154841-2-git-send-email-john.garry@huawei.comSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

[ Upstream commit dce8e237 ]

KCSAN find inode->i_disksize could be accessed concurrently.

BUG: KCSAN: data-race in ext4_mark_iloc_dirty / ext4_write_end

write (marked) to 0xffff8b8932f40090 of 8 bytes by task 66792 on cpu 0:
 ext4_write_end+0x53f/0x5b0
 ext4_da_write_end+0x237/0x510
 generic_perform_write+0x1c4/0x2a0
 ext4_buffered_write_iter+0x13a/0x210
 ext4_file_write_iter+0xe2/0x9b0
 new_sync_write+0x29c/0x3a0
 __vfs_write+0x92/0xa0
 vfs_write+0xfc/0x2a0
 ksys_write+0xe8/0x140
 __x64_sys_write+0x4c/0x60
 do_syscall_64+0x8a/0x2a0
 entry_SYSCALL_64_after_hwframe+0x44/0xa9

read to 0xffff8b8932f40090 of 8 bytes by task 14414 on cpu 1:
 ext4_mark_iloc_dirty+0x716/0x1190
 ext4_mark_inode_dirty+0xc9/0x360
 ext4_convert_unwritten_extents+0x1bc/0x2a0
 ext4_convert_unwritten_io_end_vec+0xc5/0x150
 ext4_put_io_end+0x82/0x130
 ext4_writepages+0xae7/0x16f0
 do_writepages+0x64/0x120
 __writeback_single_inode+0x7d/0x650
 writeback_sb_inodes+0x3a4/0x860
 __writeback_inodes_wb+0xc4/0x150
 wb_writeback+0x43f/0x510
 wb_workfn+0x3b2/0x8a0
 process_one_work+0x39b/0x7e0
 worker_thread+0x88/0x650
 kthread+0x1d4/0x1f0
 ret_from_fork+0x35/0x40

The plain read is outside of inode->i_data_sem critical section
which results in a data race. Fix it by adding READ_ONCE().
Signed-off-by: Qiujun Huang <hqjagain@gmail.com>
Link: https://lore.kernel.org/r/1582556566-3909-1-git-send-email-hqjagain@gmail.comSigned-off-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Sasha Levin <sashal@kernel.org>