Fix assignment of the FM10K_FAULT_ADDR_LO register into fault->address
by using a bit-wise |= operation. Without this, the low address is
completely overwriting the high potion of the address. This caused the
fault to incorrectly return only the lower 32 bits of the fault address.

This issue was detected by cppcheck and resolves the following warnings
produced by that tool:

[fm10k_pf.c:1668] -> [fm10k_pf.c:1670]: (style) Variable
'fault->address' is reassigned a value before the old one has been used.

[fm10k_pf.c:1669] -> [fm10k_pf.c:1670]: (style) Variable
'fault->address' is reassigned a value before the old one has been used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver currently uses a macro to decide whether we should use
NON_Q_VECTORS_PF or NON_Q_VECTORS_VF.

However, we also define NON_Q_VECTORS_VF to the same value as
NON_Q_VECTORS_PF. This means that the macro NON_Q_VECTORS(hw) will
always return the same value.

Let's just remove this macro, and replace it directly with an enum value
on the enum non_q_vectors.

This was detected by cppcheck and fixes the following warnings when
building with BUILD=KERNEL

[fm10k_ethtool.c:1123]: (style) Same value in both branches of ternary
operator.

[fm10k_ethtool.c:1142]: (style) Same value in both branches of ternary
operator.

[fm10k_main.c:1826]: (style) Same value in both branches of ternary
operator.

[fm10k_main.c:1849]: (style) Same value in both branches of ternary
operator.

[fm10k_main.c:1858]: (style) Same value in both branches of ternary
operator.

[fm10k_pci.c:901]: (style) Same value in both branches of ternary
operator.

[fm10k_pci.c:1040]: (style) Same value in both branches of ternary
operator.

[fm10k_pci.c:1726]: (style) Same value in both branches of ternary
operator.

[fm10k_pci.c:1763]: (style) Same value in both branches of ternary
operator.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Several functions in the fm10k driver have specific function templates,
as they are used as function pointers. The parameters in these functions
are not always used. Explicitly mark unused parameters with the
__always_unused macro, so that the compiler will not warn about them
when building with the -Wunused-parameter warning enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The page_addr variable is a void pointer. Incrementing it before calling
prefetch is technically undefined. Fix this by casting it to a u8*
pointer before incrementing it. This ensures that we increment the
pointer value in byte units, instead of relying on this undefined
behavior.

This was detected by cppcheck, and resolves the following warning
produced by that tool:

[fm10k_main.c:328]: (portability) 'page_addr' is of type 'void *'. When
using void pointers in calculations, the behaviour is undefined.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

In the fm10k_handle_resume function, return 0 explicitly at the end of
the function instead of returning the err value.

This was detected by cppcheck and resolves the following style warning
produced by that tool:

[fm10k_pci.c:2768] -> [fm10k_pci.c:2787]: (warning) Identical condition
'err', second condition is always false
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The local variable 'size' in fm10k_dfwd_add_station is initialized, but
is always re-assigned immediately before use. Remove this unnecessary
initialization.

This was detected by cppcheck and resolves the following warning
produced by that tool:

[fm10k_netdev.c:1466]: (style) Variable 'size' is assigned a value that is never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The local variable err in several functions in the fm10k_netdev.c file
is initialized with a value that is never used. The err value is
immediately re-assigned in all cases where it will be checked. Remove
the unnecessary initializers.

This was detected by cppcheck and resolves the following warnings
produced by that tool:

[fm10k_netdev.c:999] -> [fm10k_netdev.c:1004]: (style) Variable 'err' is
reassigned a value before the old one has been used.

[fm10k_netdev.c:1019] -> [fm10k_netdev.c:1024]: (style) Variable 'err'
is reassigned a value before the old one has been used.

[fm10k_netdev.c:64]: (style) Variable 'err' is assigned a value that is
never used.

[fm10k_netdev.c:131]: (style) Variable 'err' is assigned a value that
is never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The err variable in the fm10k_tlv_attr_parse function is initialized
with zero. However, the function never reads err without first assigning
it from a function call. Remove this unnecessary initialization.

This was detected by cppcheck and resolves the following warning
produced by that tool:

[fm10k_tlv.c:498]: (style) Variable 'err' is assigned a value that is
never used.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

David Ahern says:

====================
net: Add functional tests for L3 and L4

This is a port the functional test cases created during the development
of the VRF feature. It covers various permutations of icmp, tcp and udp
for IPv4 and IPv6 including negative tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add use case section to fcnal-test.

Initial test is VRF based with a bridge and vlans. The commands
stem from bug reports fixed by:

a173f066 ("netfilter: bridge: Don't sabotage nf_hook calls from an l3mdev")
cd642898 ("netfilter: bridge: Don't sabotage nf_hook calls for an l3mdev slave")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv6 netfilter tests to send tcp reset or icmp unreachable for a
port. Initial tests are VRF only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add netfilter tests to send tcp reset or icmp unreachable for a port.
Initial tests are VRF only.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv6 runtime tests where passive (no traffic flowing) and active
(with traffic) sockets are expected to be reset on device deletes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add runtime tests where passive (no traffic flowing) and active (with
traffic) sockets are expected to be reset on device deletes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv6 address bind tests to fcnal-test.sh. Verifies socket binding to
local addresses for raw, tcp and udp including device and VRF cases.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add address bind tests to fcnal-test.sh. Verifies socket binding to
local addresses for raw, tcp and udp including device and VRF cases.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv6 udp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.udp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add udp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.udp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv6 tcp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.tcp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add tcp tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures for both clients and servers. Includes permutations with
net.ipv4.tcp_l3mdev_accept set to 0 and 1.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add IPv6 ping tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures.

Setup includes unreachable routes and fib rules blocking traffic.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add ping tests to fcnal-test.sh. Covers the permutations of directly
connected addresses, routed destinations, VRF and non-VRF, and expected
failures.

Setup includes unreachable routes and fib rules blocking traffic.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initial commit for functional test suite for fib and socket lookups.
This commit contains the namespace setup, networking config, test options
and other basic infrastructure.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add nettest - a simple program with an implementation for various networking
APIs. nettest is used for tcp, udp and raw functional tests for both IPv4
and IPv6.

Point of this command versus existing utilities:
- controlled implementation of the APIs and the order in which they
  are called,
- ability to verify ingress device, local and remote addresses,
- timeout for controlled test length,
- ability to discriminate a timeout from a system call failure, and
- simplicity with test scripts.

The command returns:
  0  on success,
  1  for any system call failure, and
  2  on timeout.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2019-08-01

This series for fm10k, by Jake Keller, reduces the scope of local variables
where possible.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Claudiu Manoil says:

====================
enetc: Add mdio bus driver for the PCIe MDIO endpoint

First patch fixes a sparse issue and cleans up accessors to avoid
casting to __iomem.  The second one cleans up the Makefile, to make
it easier to add new entries.

Third patch just registers the PCIe endpoint device containing
the MDIO registers as a standalone MDIO bus driver, to provide
an alternative way to control the MDIO bus.  The same code used
by the ENETC ports (eth controllers) to manage MDIO via local
registers applies and is reused.

Bindings are provided for the new MDIO node, similarly to ENETC
port nodes bindings.

Last patch enables the ENETC port 1 and its RGMII PHY on the
LS1028A QDS board, where the MDIO muxing configuration relies
on the MDIO support provided in the first patch.

Changes since v0:
v1 - fixed mdio bus allocation
v2 - cleaned up accessors to avoid casting
v3 - fixed spelling (mostly commit message)
v4 - fixed err path check blunder
v5 - fixed loadble module build, provided separate kbuild module
     for the driver
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

LS1028a has one Ethernet management interface. On the QDS board, the
MDIO signals are multiplexed to either on-board AR8035 PHY device or
to 4 PCIe slots allowing for SGMII cards.
To enable the Ethernet ENETC Port 1, which can only be connected to a
RGMII PHY, the multiplexer needs to be configured to route the MDIO to
the AR8035 PHY.  The MDIO/MDC routing is controlled by bits 7:4 of FPGA
board config register 0x54, and value 0 selects the on-board RGMII PHY.
The FPGA board config registers are accessible on the i2c bus, at address
0x66.

The PF3 MDIO PCIe integrated endpoint device allows for centralized access
to the MDIO bus.  Add the corresponding devicetree node and set it to be
the MDIO bus parent.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The on-chip PCIe root complex that integrates the ENETC ethernet
controllers also integrates a PCIe endpoint for the MDIO controller
providing for centralized control of the ENETC mdio bus.
Add bindings for this "central" MDIO Integrated PCIe Endpoint.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

ENETC ports can manage the MDIO bus via local register
interface.  However there's also a centralized way
to manage the MDIO bus, via the MDIO PCIe endpoint
device integrated by the same root complex that also
integrates the ENETC ports (eth controllers).

Depending on board design and use case, centralized
access to MDIO may be better than using local ENETC
port registers.  For instance, on the LS1028A QDS board
where MDIO muxing is required.  Also, the LS1028A on-chip
switch doesn't have a local MDIO register interface.

The current patch registers the above PCIe endpoint as a
separate MDIO bus and provides a driver for it by re-using
the code used for local MDIO access.  It also allows the
ENETC port PHYs to be managed by this driver if the local
"mdio" node is missing from the ENETC port node.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Clean up overcomplicated makefile to make it more maintainable.
Basically, there's a set of common objects shared between
the PF and VF driver modules.  This can be implemented in a
simpler way, without conditionals, less repetition, allowing
also for easier updates in the future.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

What's needed is basically a pointer to the mdio registers.
This is one way to store it inside bus->priv allocated space,
without upsetting sparse.
Reworked accessors to avoid __iomem casting.
Used devm_* variant to further clean up the init error /
remove paths.

Fixes following sparse warning:
 warning: incorrect type in assignment (different address spaces)
    expected void *priv
    got struct enetc_mdio_regs [noderef] <asn:2>*[assigned] regs

Fixes: ebfcb23d ("enetc: Add ENETC PF level external MDIO support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Hubert Feurstein says:

====================
net: dsa: mv88e6xxx: add support for MV88E6220

This patch series adds support for the MV88E6220 chip to the mv88e6xxx driver.
The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins.

Furthermore, PTP support is added to the MV88E6250 family.

v2:
 - insert all 6220 entries in correct numerical order
 - introduce invalid_port_mask
 - move ptp_cc_mult* to ptp_ops and restored original ptp_adjfine code
 - added Andrews Reviewed-By to patch 2 and 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This adds PTP support for the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

As it is done for all the other structs within this driver.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MV88E6250 family doesn't support the MV88E6XXX_PORT_CTL1_MESSAGE_PORT
bit.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

With this it is possible to mark certain chip ports as invalid. This is
required for example for the MV88E6220 (which is in general a MV88E6250
with 7 ports) but the ports 2-4 are not routed to pins.

If a user configures an invalid port, an error is returned.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MV88E6220 is part of the MV88E6250 family.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MV88E6220 is almost the same as MV88E6250 except that the ports 2-4 are
not routed to pins. So the usable ports are 0, 1, 5 and 6.
Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Andrew Jeffery says:

====================
net: phy: Add AST2600 MDIO support

v2 of the ASPEED MDIO series addresses comments from Rob on the devicetree
bindings and Andrew on the driver itself.

v1 of the series can be found here:

http://patchwork.ozlabs.org/cover/1138140/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ensures we can talk to a PHY via MDIO on the AST2600, as the MDIO
controller is now separate from the MAC.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>