- 13 Apr, 2015 40 commits
-
-
Larry Finger authored
commit c8f03455 upstream. Routine rtl_is_special_data() is supposed to identify packets that need to use a low bit rate so that the probability of successful transmission is high. The current version has a bug that causes all IPv6 packets to be labelled as special, with a corresponding low rate of transmission. A complete fix will be quite intrusive, but until that is available, all IPv6 packets are identified as regular. This patch also removes a magic number. Reported-and-tested-by:
Alan Fisher <acf@unixcube.org> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Cc: Alan Fisher <acf@unixcube.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Thierry Reding authored
commit 2f1bce48 upstream. devm_phy_create() stores the pointer to the new PHY at the address returned by devres_alloc(). The res parameter passed to devm_phy_match() is therefore the location where the pointer to the PHY is stored, hence it needs to be dereferenced before comparing to the match data in order to find the correct match. Signed-off-by:
Thierry Reding <treding@nvidia.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by:
-
Peter Chen authored
commit a886bd92 upstream. We should signal connect (pull up dp) after we have already at peripheral mode, otherwise, the dp may be toggled due to we reset controller or do disconnect during the initialization for peripheral, then, the host may be confused during the enumeration, eg, it finds the reset can't succeed, but the device is still there, see below error message. hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: cannot reset port 1 (err = -32) hub 1-0:1.0: Cannot enable port 1. Maybe the USB cable is bad? hub 1-0:1.0: unable to enumerate USB device on port 1 Fixes: the issue existed when the otg fsm code was added. Signed-off-by:
Peter Chen <peter.chen@freescale.com> Signed-off-by:
-
Li Jun authored
commit d20f7807 upstream. This patch adds response to a_alt_hnp_support set feature request from legacy A device, that is, B-device can provide a message to the user indicating that the user needs to connect the B-device to an alternate port on the A-device. A device sets this feature indicates to the B-device that it is connected to an A-device port that is not capable of HNP, but that the A-device does have an alternate port that is capable of HNP. [Peter] Without this patch, the OTG B device can't be enumerated on non-HNP port at A device, see below log: [ 2.287464] usb 1-1: Dual-Role OTG device on non-HNP port [ 2.293105] usb 1-1: can't set HNP mode: -32 [ 2.417422] usb 1-1: new high-speed USB device number 4 using ci_hdrc [ 2.460635] usb 1-1: Dual-Role OTG device on non-HNP port [ 2.466424] usb 1-1: can't set HNP mode: -32 [ 2.587464] usb 1-1: new high-speed USB device number 5 using ci_hdrc [ 2.630649] usb 1-1: Dual-Role OTG device on non-HNP port [ 2.636436] usb 1-1: can't set HNP mode: -32 [ 2.641003] usb usb1-port1: unable to enumerate USB device Acked-by:
Li Jun <b47624@freescale.com> Signed-off-by:
-
David Dueck authored
commit d0f347d6 upstream. This fixes a potential null pointer dereference. Fixes: d4332013 ("driver core: dev_get_drvdata: Don't check for NULL dev") Acked-by:
Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by:
David Dueck <davidcdueck@googlemail.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> Signed-off-by:
-
Hans de Goede authored
commit bda13e35 upstream. A new uas compatible controller has shown up in some people's devices from the manufacturer Initio Corporation, this controller needs the US_FL_NO_ATA_1X quirk to work properly with uas, so add it to the uas quirks table. Reported-and-tested-by:
Benjamin Tissoires <benjamin.tissoires@redhat.com> Cc: Benjamin Tissoires <benjamin.tissoires@redhat.com> Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Andrei Otcheretianski authored
commit 833d9b97 upstream. iwl_mvm_stop_roc removes TE only if running flag is set. This is not correct since this flag is only set when the TE is started. This resulted in a TE not being removed, when mac80211 believes that there are no active ROCs. Fixes: bf5da87f ("iwlwifi: mvm: add remove flow for AUX ROC time events") Signed-off-by:
Andrei Otcheretianski <andrei.otcheretianski@intel.com> Reviewed-by:
Matti Gottlieb <matti.gottlieb@intel.com> Signed-off-by:
Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by:
-
Emmanuel Grumbach authored
commit 4cd4b50c upstream. The commit below introduced an unsafe dereference of mvmvif->phy_ctxt. It can be NULL even if we hold the mutex. We can be handling a BT Coex notification while the vif has already been unassigned. This can happen since the BT Coex notification is hanled asynchronuously: we can have started to handle the BT Coex notification trying to acquire the mutex while the unassign flow already got it. The BT Coex notification handling will wait for the mutext. I'll get it later, but then mvmvif->phy_ctxt will be NULL. Panic log: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<f985180d>] iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm] *pdpt = 0000000000000000 *pde = f000eef300000007 Oops: 0000 [#1] SMP Workqueue: events iwl_mvm_async_handlers_wk [iwlmvm] task: ed719b20 ti: ec03e000 task.ti: ec03e000 EIP: 0060:[<f985180d>] EFLAGS: 00010202 CPU: 2 EIP is at iwl_mvm_bt_notif_iterator+0x9d/0x340 [iwlmvm] EAX: 00000000 EBX: f6d3cb70 ECX: f6d3cb70 EDX: 00000000 ESI: ec03fe40 EDI: efeb8810 EBP: ec03fdf0 ESP: ec03fdac DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 CR0: 80050033 CR2: 00000000 CR3: 01a1a000 CR4: 001407f0 Stack: f743ca80 f744a404 ec03fdcc c10e3952 00003aba f743ca80 00000246 f743ca80 00000246 00000000 00000001 00000000 ebd45ff6 ebd458a4 f6d3c500 ebd45578 ebd44b01 ec03fe18 f99e1bc2 00000002 ebd44bc0 f9851770 00000000 f6d3c500 Call Trace: [<c10e3952>] ? ring_buffer_unlock_commit+0xa2/0xd0 [<f99e1bc2>] __iterate_interfaces+0x82/0x110 [mac80211] [<f9851770>] ? iwl_mvm_bt_coex_reduced_txp+0x140/0x140 [iwlmvm] [<f99e1c6a>] ieee80211_iterate_active_interfaces_atomic+0x1a/0x20 [mac80211] [<f9851427>] iwl_mvm_bt_coex_notif_handle+0x77/0x280 [iwlmvm] [<f9852161>] iwl_mvm_rx_bt_coex_notif_old+0x211/0x220 [iwlmvm] [<f9850b8b>] iwl_mvm_rx_bt_coex_notif+0x19b/0x1b0 [iwlmvm] [<f983944f>] iwl_mvm_async_handlers_wk+0x7f/0xe0 [iwlmvm] Fixes: 123f5156 ("iwlwifi: mvm: BT Coex - add support for TTC / RRC") Signed-off-by:
-
Emmanuel Grumbach authored
commit 540623ca upstream. The commit below didn't update the max_ht_ampdu_exponent for the devices listed in iwl-[1-6]000.c which, in result, became 0 instead of 8K. This reduced the size of the Rx AMPDU from 64K to 8K which had an impact in the Rx throughput. One user reported that because of this, his downstream throughput droppped by a half. Fixes: c064ddf3 ("iwlwifi: change max HT and VHT A-MPDU exponent") Reported-and-tested-by:
Valentin Manea <linux-wireless@mrs.ro> Signed-off-by:
-
Eyal Shapira authored
commit 57bff148 upstream. The check to avoid the shared antenna was passed the wrong antenna parameter. It should have checked whether the antenna of the next column we're considering is allowed and instead it was passed the current antenna. This could lead to a wrong choice of the next column in the rs algorithm and non optimal performance. Fixes: commit 219fb66b ("iwlwifi: mvm: rs - don't use the shared antenna when BT load is high") Signed-off-by:
Eyal Shapira <eyalx.shapira@intel.com> Reviewed-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Jacob Pan authored
commit d474a4d3 upstream. The current driver assumes all RAPL domains within a CPU package have the same energy unit. This is no longer true for HSW server CPUs since DRAM domain has is own fixed energy unit which can be different than the package energy unit enumerated by package power MSR. In fact, the default HSW EP package power unit is 61uJ whereas DRAM domain unit is 15.3uJ. The result is that DRAM power consumption is counted 4x more than real power reported by energy counters, similarly for max_energy_range_uj of DRAM domain. This patch adds domain specific energy unit per cpu type, it allows domain energy unit to override package energy unit if non zero. Please see this document for details. "Intel Xeon Processor E5-1600 and E5-2600 v3 Product Families, Volume 2 of 2. Datasheet, September 2014, Reference Number: 330784-001 " Signed-off-by:
Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Andrei Otcheretianski authored
commit 0f611d28 upstream. Since moving the interface combination checks to mac80211, it's broken because it now only considers interfaces with an assigned channel context, so for example any interface that isn't active can still be up, which is clearly an issue; also, in particular P2P-Device wdevs are an issue since they never have a chanctx. Fix this by counting running interfaces instead the ones with a channel context assigned. Fixes: 73de86a3 ("cfg80211/mac80211: move interface counting for combination check to mac80211") Signed-off-by:
-
Bob Copeland authored
commit d0c22119 upstream. The mesh forwarding path was not checking that data frames were protected when running an encrypted network; add the necessary check. Reported-by:
Johannes Berg <johannes@sipsolutions.net> Signed-off-by:
Bob Copeland <me@bobcopeland.com> Signed-off-by:
-
Michal Kazior authored
commit aa75ebc2 upstream. Some APs experience problems when working with U-APSD. Decreasing the probability of that happening by using legacy mode for all ACs but VO isn't enough. Cisco 4410N originally forced us to enable VO by default only because it treated non-VO ACs as legacy. However some APs (notably Netgear R7000) silently reclassify packets to different ACs. Since u-APSD ACs require trigger frames for frame retrieval clients would never see some frames (e.g. ARP responses) or would fetch them accidentally after a long time. It makes little sense to enable u-APSD queues by default because it needs userspace applications to be aware of it to actually take advantage of the possible additional powersavings. Implicitly depending on driver autotrigger frame support doesn't make much sense. Signed-off-by:
Michal Kazior <michal.kazior@tieto.com> Signed-off-by:
-
Johannes Berg authored
commit 496fcc29 upstream. As HT/VHT depend heavily on QoS/WMM, it's not a good idea to let userspace add clients that have HT/VHT but not QoS/WMM. Since it does so in certain cases we've observed (client is using HT IEs but not QoS/WMM) just ignore the HT/VHT info at this point and don't pass it down to the drivers which might unconditionally use it. Signed-off-by:
-
Benjamin Tissoires authored
commit b57a7128 upstream. The board id capability has been added in firmware 7.5. Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Benjamin Tissoires authored
commit ebc80840 upstream. The Fimware 8.1 has a bug in which the extra buttons are only sent when the ExtBit is 1. This should be fixed in a future FW update which should have a bump of the minor version. Signed-off-by:
-
Dmitry Torokhov authored
commit dc5465dc upstream. On the X1 Carbon 3rd gen (with a 2015 broadwell cpu), the physical middle button of the trackstick (attached to the touchpad serio device, of course) seems to get lost. Actually, the touchpads reports 3 extra buttons, which falls in the switch below to the '2' case. Let's handle the case of odd numbers also, so that the middle button finds its way back. Signed-off-by:
-
Benjamin Tissoires authored
commit 02e07492 upstream. Post-2013 Lenovo laptops provide correct min/max dimensions, which are different with the ones currently quirked. According to https://bugzilla.kernel.org/show_bug.cgi?id=91541 the following board ids are assigned in the post-2013 touchpads: t440p/t440s: LEN0036 -> 2964/2962 t540p: LEN0034 -> 2964 Using 2961 as the common minimum makes these 3 laptops OK. We may need to update those values later if other pnp_ids has a lower board_id. Signed-off-by:
-
Daniel Martin authored
commit 5b3089dd upstream. Add a min/max range for board ids to the min/max coordinates quirk. This makes it possible to restrict quirks to specific models based upon their board id. The define ANY_BOARD_ID (0) serves as a wild card. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541Signed-off-by:
Daniel Martin <daniel.martin@secunet.com> Acked-by:
-
Daniel Martin authored
commit b05f4d1c upstream. The firmware of the X240 (LEN0035, 2013/12) exposes the same values x [1232..5710], y [1156..4696] as the quirk applies. Signed-off-by:
Daniel Martin <consume.noise@gmail.com> Acked-by:
-
Daniel Martin authored
commit ac097930 upstream. Query the min dimensions even if the check SYN_EXT_CAP_REQUESTS(priv->capabilities) >= 7 fails, but we know that the firmware version 8.1 is safe. With that we don't need quirks for post-2013 models anymore as they expose correct min and max dimensions. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=91541Signed-off-by:
-
Daniel Martin authored
commit 9aff6598 upstream. Logging the dimension values we queried and the values we use from a quirk to overwrite can be helpful for debugging. This partly relates to bug: https://bugzilla.kernel.org/show_bug.cgi?id=91541Signed-off-by:
-
Daniel Martin authored
commit 8b04baba upstream. Split the function synaptics_resolution() into synaptics_resolution() and synaptics_quirks(). synaptics_resolution() will be called before synaptics_quirks() to query dimensions and resolutions before overwriting them with quirks. Signed-off-by:
-
Bart Van Assche authored
commit 75c3d0bf upstream. This patch fixes the incorrect use of __transport_register_session() in tcm_qla2xxx_check_initiator_node_acl() code, that does not perform explicit se_tpg->session_lock when accessing se_tpg->tpg_sess_list to add new se_sess nodes. Given that tcm_qla2xxx_check_initiator_node_acl() is not called with qla_hw->hardware_lock held for all accesses of ->tpg_sess_list, the code should be using transport_register_session() instead. Signed-off-by:
Bart Van Assche <bart.vanassche@sandisk.com> Cc: Giridhar Malavali <giridhar.malavali@qlogic.com> Cc: Quinn Tran <quinn.tran@qlogic.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Dan Carpenter authored
commit d556546e upstream. This patch adds a missing set of conditional check braces in ft_invl_hw_context() originally introduced by commit dcd998cc when handling DDP failures in ft_recv_write_data() code. commit dcd998cc Author: Kiran Patil <kiran.patil@intel.com> Date: Wed Aug 3 09:20:01 2011 +0000 tcm_fc: Handle DDP/SW fc_frame_payload_get failures in ft_recv_write_data Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Cc: Kiran Patil <kiran.patil@intel.com> Signed-off-by:
-
Yongbae Park authored
commit 7b8f10da upstream. The initialisation of the efm32 clocksource first sets up the irq and only after that initialises the data needed for irq handling. In case this initialisation is delayed the irq handler would dereference a NULL pointer. I'm not aware of anything that could delay the process in such a way, but it's better to be safe than sorry, so setup the irq only when the clock event device is ready. Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
Yongbae Park <yongbae2@gmail.com> Signed-off-by:
Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by:
-
Philipp Zabel authored
commit c6b570d9 upstream. This patch fixes a NULL pointer dereference when enabling regmap event tracing in the presence of a syscon regmap, introduced by commit bdb0066d ("mfd: syscon: Decouple syscon interface from platform devices"). That patch introduced syscon regmaps that have their dev field set to NULL. The regmap trace events expect it to point to a valid struct device and feed it to dev_name(): $ echo 1 > /sys/kernel/debug/tracing/events/regmap/enable Unable to handle kernel NULL pointer dereference at virtual address 0000002c pgd = 80004000 [0000002c] *pgd=00000000 Internal error: Oops: 17 [#1] SMP ARM Modules linked in: coda videobuf2_vmalloc CPU: 0 PID: 304 Comm: kworker/0:2 Not tainted 4.0.0-rc2+ #9197 Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree) Workqueue: events_freezable thermal_zone_device_check task: 9f25a200 ti: 9f1ee000 task.ti: 9f1ee000 PC is at ftrace_raw_event_regmap_block+0x3c/0xe4 LR is at _regmap_raw_read+0x1bc/0x1cc pc : [<803636e8>] lr : [<80365f2c>] psr: 600f0093 sp : 9f1efd78 ip : 9f1efdb8 fp : 9f1efdb4 r10: 00000004 r9 : 00000001 r8 : 00000001 r7 : 00000180 r6 : 00000000 r5 : 9f00e3c0 r4 : 00000003 r3 : 00000001 r2 : 00000180 r1 : 00000000 r0 : 9f00e3c0 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 2d91004a DAC: 00000015 Process kworker/0:2 (pid: 304, stack limit = 0x9f1ee210) Stack: (0x9f1efd78 to 0x9f1f0000) fd60: 9f1efda4 9f1efd88 fd80: 800708c0 805f9510 80927140 800f0013 9f1fc800 9eb2f490 00000000 00000180 fda0: 808e3840 00000001 9f1efdfc 9f1efdb8 80365f2c 803636b8 805f8958 800708e0 fdc0: a00f0013 803636ac 9f16de00 00000180 80927140 9f1fc800 9f1fc800 9f1efe6c fde0: 9f1efe6c 9f732400 00000000 00000000 9f1efe1c 9f1efe00 80365f70 80365d7c fe00: 80365f3c 9f1fc800 9f1fc800 00000180 9f1efe44 9f1efe20 803656a4 80365f48 fe20: 9f1fc800 00000180 9f1efe6c 9f1efe6c 9f732400 00000000 9f1efe64 9f1efe48 fe40: 803657bc 80365634 00000001 9e95f910 9f1fc800 9f1efeb4 9f1efe8c 9f1efe68 fe60: 80452ac0 80365778 9f1efe8c 9f1efe78 9e93d400 9e93d5e8 9f1efeb4 9f72ef40 fe80: 9f1efeac 9f1efe90 8044e11c 80452998 8045298c 9e93d608 9e93d400 808e1978 fea0: 9f1efecc 9f1efeb0 8044fd14 8044e0d0 ffffffff 9f25a200 9e93d608 9e481380 fec0: 9f1efedc 9f1efed0 8044fde8 8044fcec 9f1eff1c 9f1efee0 80038d50 8044fdd8 fee0: 9f1ee020 9f72ef40 9e481398 00000000 00000008 9f72ef54 9f1ee020 9f72ef40 ff00: 9e481398 9e481380 00000008 9f72ef40 9f1eff5c 9f1eff20 80039754 80038bfc ff20: 00000000 9e481380 80894100 808e1662 00000000 9e4f2ec0 00000000 9e481380 ff40: 800396f8 00000000 00000000 00000000 9f1effac 9f1eff60 8003e020 80039704 ff60: ffffffff 00000000 ffffffff 9e481380 00000000 00000000 9f1eff78 9f1eff78 ff80: 00000000 00000000 9f1eff88 9f1eff88 9e4f2ec0 8003df30 00000000 00000000 ffa0: 00000000 9f1effb0 8000eb60 8003df3c 00000000 00000000 00000000 00000000 ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff Backtrace: [<803636ac>] (ftrace_raw_event_regmap_block) from [<80365f2c>] (_regmap_raw_read+0x1bc/0x1cc) r9:00000001 r8:808e3840 r7:00000180 r6:00000000 r5:9eb2f490 r4:9f1fc800 [<80365d70>] (_regmap_raw_read) from [<80365f70>] (_regmap_bus_read+0x34/0x6c) r10:00000000 r9:00000000 r8:9f732400 r7:9f1efe6c r6:9f1efe6c r5:9f1fc800 r4:9f1fc800 [<80365f3c>] (_regmap_bus_read) from [<803656a4>] (_regmap_read+0x7c/0x144) r6:00000180 r5:9f1fc800 r4:9f1fc800 r3:80365f3c [<80365628>] (_regmap_read) from [<803657bc>] (regmap_read+0x50/0x70) r9:00000000 r8:9f732400 r7:9f1efe6c r6:9f1efe6c r5:00000180 r4:9f1fc800 [<8036576c>] (regmap_read) from [<80452ac0>] (imx_get_temp+0x134/0x1a4) r6:9f1efeb4 r5:9f1fc800 r4:9e95f910 r3:00000001 [<8045298c>] (imx_get_temp) from [<8044e11c>] (thermal_zone_get_temp+0x58/0x74) r7:9f72ef40 r6:9f1efeb4 r5:9e93d5e8 r4:9e93d400 [<8044e0c4>] (thermal_zone_get_temp) from [<8044fd14>] (thermal_zone_device_update+0x34/0xec) r6:808e1978 r5:9e93d400 r4:9e93d608 r3:8045298c [<8044fce0>] (thermal_zone_device_update) from [<8044fde8>] (thermal_zone_device_check+0x1c/0x20) r5:9e481380 r4:9e93d608 [<8044fdcc>] (thermal_zone_device_check) from [<80038d50>] (process_one_work+0x160/0x3d4) [<80038bf0>] (process_one_work) from [<80039754>] (worker_thread+0x5c/0x4f4) r10:9f72ef40 r9:00000008 r8:9e481380 r7:9e481398 r6:9f72ef40 r5:9f1ee020 r4:9f72ef54 [<800396f8>] (worker_thread) from [<8003e020>] (kthread+0xf0/0x108) r10:00000000 r9:00000000 r8:00000000 r7:800396f8 r6:9e481380 r5:00000000 r4:9e4f2ec0 [<8003df30>] (kthread) from [<8000eb60>] (ret_from_fork+0x14/0x34) r7:00000000 r6:00000000 r5:8003df30 r4:9e4f2ec0 Code: e3140040 1a00001a e3140020 1a000016 (e596002c) ---[ end trace 193c15c2494ec960 ]--- Fixes: bdb0066d (mfd: syscon: Decouple syscon interface from platform devices) Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Lars-Peter Clausen authored
commit 328f494d upstream. When inserting a new register into a block at the lower end the present bitmap is currently shifted into the wrong direction. The effect of this is that the bitmap becomes corrupted and registers which are present might be reported as not present and vice versa. Fix this by shifting left rather than right. Fixes: 472fdec7("regmap: rbtree: Reduce number of nodes, take 2") Reported-by:
Daniel Baluta <daniel.baluta@gmail.com> Signed-off-by:
Lars-Peter Clausen <lars@metafoo.de> Signed-off-by:
-
Yongbae Park authored
commit 1096be08 upstream. The interrupt is enabled before the handler is set. Even this bug did not appear, it is potentially dangerous as it can lead to a NULL pointer dereference. Fix the error by enabling the interrupt after clockevents_config_and_register() is called. Signed-off-by:
-
Michael S. Tsirkin authored
commit 3d2a3774 upstream. virtio balloon has this code: wait_event_interruptible(vb->config_change, (diff = towards_target(vb)) != 0 || vb->need_stats_update || kthread_should_stop() || freezing(current)); Which is a problem because towards_target() call might block after wait_event_interruptible sets task state to TAST_INTERRUPTIBLE, causing the task_struct::state collision typical of nesting of sleeping primitives See also http://lwn.net/Articles/628628/ or Thomas's bug report http://article.gmane.org/gmane.linux.kernel.virtualization/24846 for a fuller explanation. To fix, rewrite using wait_woken. Reported-by:
Thomas Huth <thuth@linux.vnet.ibm.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Tested-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by:
Rusty Russell <rusty@rustcorp.com.au> Signed-off-by:
-
Michael S. Tsirkin authored
commit 88660f7f upstream. virtio spec requires that all drivers set DRIVER_OK before using devices. While balloon isn't yet included in the virtio 1 spec, previous spec versions also required this. virtio balloon might violate this rule: probe calls kthread_run before setting DRIVER_OK, which might run immediately and cause balloon to inflate/deflate. To fix, call virtio_device_ready before running the kthread. Signed-off-by:
-
Takashi Iwai authored
commit 87a8b286 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
Takashi Iwai <tiwai@suse.de> Acked-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Takashi Iwai authored
commit 4b0b669b upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 07892b10 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 2bf4c1d4 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 08641d9b upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit eaddf6fd upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 24cc883c upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
Takashi Iwai authored
commit 00a14c29 upstream. The correct values referred by a boolean control are value.integer.value[], not value.enumerated.item[]. The former is long while the latter is int, so it's even incompatible on 64bit architectures. Signed-off-by:
-
