- 30 Oct, 2014 40 commits
-
-
Sowmini Varadhan authored
[ Upstream commit c21c4ab0 ] The request_irq() needs to be done from ldc_alloc() to avoid the following (caught by lockdep) [00000000004a0738] __might_sleep+0xf8/0x120 [000000000058bea4] kmem_cache_alloc_trace+0x184/0x2c0 [00000000004faf80] request_threaded_irq+0x80/0x160 [000000000044f71c] ldc_bind+0x7c/0x220 [0000000000452454] vio_port_up+0x54/0xe0 [00000000101f6778] probe_disk+0x38/0x220 [sunvdc] [00000000101f6b8c] vdc_port_probe+0x22c/0x300 [sunvdc] [0000000000451a88] vio_device_probe+0x48/0x60 [000000000074c56c] really_probe+0x6c/0x300 [000000000074c83c] driver_probe_device+0x3c/0xa0 [000000000074c92c] __driver_attach+0x8c/0xa0 [000000000074a6ec] bus_for_each_dev+0x6c/0xa0 [000000000074c1dc] driver_attach+0x1c/0x40 [000000000074b0fc] bus_add_driver+0xbc/0x280 Signed-off-by:
Sowmini Varadhan <sowmini.varadhan@oracle.com> Acked-by:
Dwight Engen <dwight.engen@oracle.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
bob picco authored
[ Upstream commit 3dee9df5 ] We have seen an issue with guest boot into LDOM that causes early boot failures because of no matching rules for node identitity of the memory. I analyzed this on my T4 and concluded there might not be a solution. I saw the issue in mainline too when booting into the control/primary domain - with guests configured. Note, this could be a firmware bug on some older machines. I'll provide a full explanation of the issues below. Should we not find a matching BEST latency group for a real address (RA) then we will assume node 0. On the T4-2 here with the information provided I can't see an alternative. Technically the LDOM shown below should match the MBLOCK to the favorable latency group. However other factors must be considered too. Were the memory controllers configured "fine" grained interleave or "coarse" grain interleaved - T4. Also should a "group" MD node be considered a NUMA node? There has to be at least one Machine Description (MD) "group" and hence one NUMA node. The group can have one or more latency groups (lg) - more than one memory controller. The current code chooses the smallest latency as the most favorable per group. The latency and lg information is in MLGROUP below. MBLOCK is the base and size of the RAs for the machine as fetched from OBP /memory "available" property. My machine has one MBLOCK but more would be possible - with holes? For a T4-2 the following information has been gathered: with LDOM guest MEMBLOCK configuration: memory size = 0x27f870000 memory.cnt = 0x3 memory[0x0] [0x00000020400000-0x0000029fc67fff], 0x27f868000 bytes memory[0x1] [0x0000029fd8a000-0x0000029fd8bfff], 0x2000 bytes memory[0x2] [0x0000029fd92000-0x0000029fd97fff], 0x6000 bytes reserved.cnt = 0x2 reserved[0x0] [0x00000020800000-0x000000216c15c0], 0xec15c1 bytes reserved[0x1] [0x00000024800000-0x0000002c180c1e], 0x7980c1f bytes MBLOCK[0]: base[20000000] size[280000000] offset[0] (note: "base" and "size" reported in "MBLOCK" encompass the "memory[X]" values) (note: (RA + offset) & mask = val is the formula to detect a match for the memory controller. should there be no match for find_node node, a return value of -1 resulted for the node - BAD) There is one group. It has these forward links MLGROUP[1]: node[545] latency[1f7e8] match[200000000] mask[200000000] MLGROUP[2]: node[54d] latency[2de60] match[0] mask[200000000] NUMA NODE[0]: node[545] mask[200000000] val[200000000] (latency[1f7e8]) (note: "val" is the best lg's (smallest latency) "match") no LDOM guest - bare metal MEMBLOCK configuration: memory size = 0xfdf2d0000 memory.cnt = 0x3 memory[0x0] [0x00000020400000-0x00000fff6adfff], 0xfdf2ae000 bytes memory[0x1] [0x00000fff6d2000-0x00000fff6e7fff], 0x16000 bytes memory[0x2] [0x00000fff766000-0x00000fff771fff], 0xc000 bytes reserved.cnt = 0x2 reserved[0x0] [0x00000020800000-0x00000021a04580], 0x1204581 bytes reserved[0x1] [0x00000024800000-0x0000002c7d29fc], 0x7fd29fd bytes MBLOCK[0]: base[20000000] size[fe0000000] offset[0] there are two groups group node[16d5] MLGROUP[0]: node[1765] latency[1f7e8] match[0] mask[200000000] MLGROUP[3]: node[177d] latency[2de60] match[200000000] mask[200000000] NUMA NODE[0]: node[1765] mask[200000000] val[0] (latency[1f7e8]) group node[171d] MLGROUP[2]: node[1775] latency[2de60] match[0] mask[200000000] MLGROUP[1]: node[176d] latency[1f7e8] match[200000000] mask[200000000] NUMA NODE[1]: node[176d] mask[200000000] val[200000000] (latency[1f7e8]) (note: for this two "group" bare metal machine, 1/2 memory is in group one's lg and 1/2 memory is in group two's lg). Cc: sparclinux@vger.kernel.org Signed-off-by:
Bob Picco <bob.picco@oracle.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 84bd6d8b ] Every path that ends up at do_sparc64_fault() must install a valid FAULT_CODE_* bitmask in the per-thread fault code byte. Two paths leading to the label winfix_trampoline (which expects the FAULT_CODE_* mask in register %g4) were not doing so: 1) For pre-hypervisor TLB protection violation traps, if we took the 'winfix_trampoline' path we wouldn't have %g4 initialized with the FAULT_CODE_* value yet. Resulting in using the TLB_TAG_ACCESS register address value instead. 2) In the TSB miss path, when we notice that we are going to use a hugepage mapping, but we haven't allocated the hugepage TSB yet, we still have to take the window fixup case into consideration and in that particular path we leave %g4 not setup properly. Errors on this sort were largely invisible previously, but after commit 4ccb9272 ("sparc64: sun4v TLB error power off events") we now have a fault_code mask bit (FAULT_CODE_BAD_RA) that triggers due to this bug. FAULT_CODE_BAD_RA triggers because this bit is set in TLB_TAG_ACCESS (see #1 above) and thus we get seemingly random bus errors triggered for user processes. Fixes: 4ccb9272 ("sparc64: sun4v TLB error power off events") Reported-by:
Meelis Roos <mroos@linux.ee> Signed-off-by:
-
bob picco authored
[ Upstream commit 4ccb9272 ] We've witnessed a few TLB events causing the machine to power off because of prom_halt. In one case it was some nfs related area during rmmod. Another was an mmapper of /dev/mem. A more recent one is an ITLB issue with a bad pagesize which could be a hardware bug. Bugs happen but we should attempt to not power off the machine and/or hang it when possible. This is a DTLB error from an mmapper of /dev/mem: [root@sparcie ~]# SUN4V-DTLB: Error at TPC[fffff80100903e6c], tl 1 SUN4V-DTLB: TPC<0xfffff80100903e6c> SUN4V-DTLB: O7[fffff801081979d0] SUN4V-DTLB: O7<0xfffff801081979d0> SUN4V-DTLB: vaddr[fffff80100000000] ctx[1250] pte[98000000000f0610] error[2] . This is recent mainline for ITLB: [ 3708.179864] SUN4V-ITLB: TPC<0xfffffc010071cefc> [ 3708.188866] SUN4V-ITLB: O7[fffffc010071cee8] [ 3708.197377] SUN4V-ITLB: O7<0xfffffc010071cee8> [ 3708.206539] SUN4V-ITLB: vaddr[e0003] ctx[1a3c] pte[2900000dcc800eeb] error[4] . Normally sun4v_itlb_error_report() and sun4v_dtlb_error_report() would call prom_halt() and drop us to OF command prompt "ok". This isn't the case for LDOMs and the machine powers off. For the HV reported error of HV_ENORADDR for HV HV_MMU_MAP_ADDR_TRAP we cause a SIGBUS error by qualifying it within do_sparc64_fault() for fault code mask of FAULT_CODE_BAD_RA. This is done when trap level (%tl) is less or equal one("1"). Otherwise, for %tl > 1, we proceed eventually to die_if_kernel(). The logic of this patch was partially inspired by David Miller's feedback. Power off of large sparc64 machines is painful. Plus die_if_kernel provides more context. A reset sequence isn't a brief period on large sparc64 but better than power-off/power-on sequence. Cc: sparclinux@vger.kernel.org Signed-off-by:
-
Daniel Hellstrom authored
[ Upstream commit d1105287 ] dma_zalloc_coherent() calls dma_alloc_coherent(__GFP_ZERO) but the sparc32 implementations sbus_alloc_coherent() and pci32_alloc_coherent() doesn't take the gfp flags into account. Tested on the SPARC32/LEON GRETH Ethernet driver which fails due to dma_alloc_coherent(__GFP_ZERO) returns non zeroed pages. Signed-off-by:
Daniel Hellstrom <daniel@gaisler.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 8bccf5b3 ] Christopher reports that perf_event_print_debug() can crash in uniprocessor builds. The crash is due to pcr_ops being NULL. This happens because pcr_arch_init() is only invoked by smp_cpus_done() which only executes in SMP builds. init_hw_perf_events() is closely intertwined with pcr_ops being setup properly, therefore: 1) Call pcr_arch_init() early on from init_hw_perf_events(), instead of from smp_cpus_done(). 2) Do not hook up a PMU type if pcr_ops is NULL after pcr_arch_init(). 3) Move init_hw_perf_events to a later initcall so that it we will be sure to invoke pcr_arch_init() after all cpus are brought up. Finally, guard the one naked sequence of pcr_ops dereferences in __global_pmu_self() with an appropriate NULL check. Reported-by:
Christopher Alexander Tobias Schulze <cat.schulze@alice-dsl.net> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 58556104 ] nmi_cpu_busy() is a SMP function call that just makes sure that all of the cpus are spinning using cpu cycles while the NMI test runs. It does not need to disable IRQs because we just care about NMIs executing which will even with 'normal' IRQs disabled. It is not legal to enable hard IRQs in a SMP cross call, in fact this bug triggers the BUG check in irq_work_run_list(): BUG_ON(!irqs_disabled()); Because now irq_work_run() is invoked from the tail of generic_smp_call_function_single_interrupt(). Signed-off-by:
-
Dave Chinner authored
commit 0d085a52 upstream. XFS has been having trouble with stray delayed allocation extents beyond EOF for a long time. Recent changes to the collapse range code has triggered erroneous EBUSY errors on page invalidtion for block size smaller than page size filesystems. These have been caused by dirty buffers beyond EOF on a partial page which do not get written to disk during a sync. The issue is that write-ahead in xfs_cluster_write() finds such a partial page and handles it by leaving the page dirty but pushing it into a writeback state. This used to work just fine, as the write_cache_pages() code would then find the dirty partial page in the next mapping tree lookup as the dirty tag is still set. Unfortunately, when we moved to a mark and sweep approach to writeback to fix other writeback sync issues, we broken this. THe act of marking the page as under writeback now clears the TOWRITE tag in the radix tree, even though the page is still dirty. This causes the TOWRITE tag to be cleared, and hence the next lookup on the mapping tree does not find the dirty partial page and so doesn't try to write it again. This same writeback bug was found recently in ext4 and fixed in commit 1c8349a1 ("ext4: fix data integrity sync in ordered mode") without communication to the wider filesystem community. We can use exactly the same fix here so the TOWRITE flag is not cleared on partial page writes. cc: stable@vger.kernel.org # dependent on 1c8349a1Root-cause-found-by:
Brian Foster <bfoster@redhat.com> Signed-off-by:
Dave Chinner <dchinner@redhat.com> Reviewed-by:
Dave Chinner <david@fromorbit.com> Signed-off-by:
-
Chao Yu authored
commit 35425ea2 upstream. Christopher Head 2014-06-28 05:26:20 UTC described: "I tried to reproduce this on 3.12.21. Instead, when I do "echo hello > foo" in an ecryptfs mount with ecryptfs_xattr specified, I get a kernel crash: BUG: unable to handle kernel NULL pointer dereference at (null) IP: [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 PGD d7840067 PUD b2c3c067 PMD 0 Oops: 0002 [#1] SMP Modules linked in: nvidia(PO) CPU: 3 PID: 3566 Comm: bash Tainted: P O 3.12.21-gentoo-r1 #2 Hardware name: ASUSTek Computer Inc. G60JX/G60JX, BIOS 206 03/15/2010 task: ffff8801948944c0 ti: ffff8800bad70000 task.ti: ffff8800bad70000 RIP: 0010:[<ffffffff8110eb39>] [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 RSP: 0018:ffff8800bad71c10 EFLAGS: 00010246 RAX: 00000000000181a4 RBX: ffff880198648480 RCX: 0000000000000000 RDX: 0000000000000004 RSI: ffff880172010450 RDI: 0000000000000000 RBP: ffff880198490e40 R08: 0000000000000000 R09: 0000000000000000 R10: ffff880172010450 R11: ffffea0002c51e80 R12: 0000000000002000 R13: 000000000000001a R14: 0000000000000000 R15: ffff880198490e40 FS: 00007ff224caa700(0000) GS:ffff88019fcc0000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000000 CR3: 00000000bb07f000 CR4: 00000000000007e0 Stack: ffffffff811826e8 ffff8800a39d8000 0000000000000000 000000000000001a ffff8800a01d0000 ffff8800a39d8000 ffffffff81185fd5 ffffffff81082c2c 00000001a39d8000 53d0abbc98490e40 0000000000000037 ffff8800a39d8220 Call Trace: [<ffffffff811826e8>] ? ecryptfs_setxattr+0x40/0x52 [<ffffffff81185fd5>] ? ecryptfs_write_metadata+0x1b3/0x223 [<ffffffff81082c2c>] ? should_resched+0x5/0x23 [<ffffffff8118322b>] ? ecryptfs_initialize_file+0xaf/0xd4 [<ffffffff81183344>] ? ecryptfs_create+0xf4/0x142 [<ffffffff810f8c0d>] ? vfs_create+0x48/0x71 [<ffffffff810f9c86>] ? do_last.isra.68+0x559/0x952 [<ffffffff810f7ce7>] ? link_path_walk+0xbd/0x458 [<ffffffff810fa2a3>] ? path_openat+0x224/0x472 [<ffffffff810fa7bd>] ? do_filp_open+0x2b/0x6f [<ffffffff81103606>] ? __alloc_fd+0xd6/0xe7 [<ffffffff810ee6ab>] ? do_sys_open+0x65/0xe9 [<ffffffff8157d022>] ? system_call_fastpath+0x16/0x1b RIP [<ffffffff8110eb39>] fsstack_copy_attr_all+0x2/0x61 RSP <ffff8800bad71c10> CR2: 0000000000000000 ---[ end trace df9dba5f1ddb8565 ]---" If we create a file when we mount with ecryptfs_xattr_metadata option, we will encounter a crash in this path: ->ecryptfs_create ->ecryptfs_initialize_file ->ecryptfs_write_metadata ->ecryptfs_write_metadata_to_xattr ->ecryptfs_setxattr ->fsstack_copy_attr_all It's because our dentry->d_inode used in fsstack_copy_attr_all is NULL, and it will be initialized when ecryptfs_initialize_file finish. So we should skip copying attr from lower inode when the value of ->d_inode is invalid. Signed-off-by:
Chao Yu <chao2.yu@samsung.com> Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Signed-off-by:
-
Fabio Estevam authored
commit d1e61eb4 upstream. Commit 78b81f46 ("ARM: dts: imx28-evk: Run I2C0 at 400kHz") caused issues when doing the following sequence in loop: - Boot the kernel - Perform audio playback - Reboot the system via 'reboot' command In many times the audio card cannot be probed, which causes playback to fail. After restoring to the original i2c0 frequency of 100kHz there is no such problem anymore. This reverts commit 78b81f46. Signed-off-by:
Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
-
klightspeed@killerwolves.net authored
commit ace85781 upstream. The bootloader on the Netgear ReadyNAS RN102 uses Hardware BCH ECC (strength = 4), while the pxa3xx NAND driver by default uses Hamming ECC (strength = 1). This patch changes the ECC mode on these machines to match that of the bootloader and of the stock firmware. That way, it is now possible to update the kernel from userland (e.g. using standard tools from mtd-utils package); u-boot will happily load and boot it. Fixes: 92beaccd ("ARM: mvebu: Enable NAND controller in ReadyNAS 102 .dts file") Signed-off-by:
Ben Peddell <klightspeed@killerwolves.net> Acked-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Tested-by:
Arnaud Ebalard <arno@natisbad.org> Link: https://lkml.kernel.org/r/1410339341-3372-1-git-send-email-klightspeed@killerwolves.netSigned-off-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
-
Arnaud Ebalard authored
commit 500abb6c upstream. The bootloader on the Netgear ReadyNAS RN2120 uses Hardware BCH ECC (strength = 4), while the pxa3xx NAND driver by default uses Hamming ECC (strength = 1). This patch changes the ECC mode on these machines to match that of the bootloader and of the stock firmware. That way, it is now possible to update the kernel from userland (e.g. using standard tools from mtd-utils package); u-boot will happily load and boot it. The issue was initially reported and fixed by Ben Pedell for RN102. The RN2120 shares the same Hynix H27U1G8F2BTR NAND flash and setup. This patch is based on Ben's fix for RN102. Fixes: ad51eddd ("ARM: mvebu: Enable NAND controller in ReadyNAS 2120 .dts file") Signed-off-by:
-
Arnaud Ebalard authored
commit 225b94cd upstream. The bootloader on the Netgear ReadyNAS RN104 uses Hardware BCH ECC (strength = 4), while the pxa3xx NAND driver by default uses Hamming ECC (strength = 1). This patch changes the ECC mode on these machines to match that of the bootloader and of the stock firmware. That way, it is now possible to update the kernel from userland (e.g. using standard tools from mtd-utils package); u-boot will happily load and boot it. The issue was initially reported and fixed by Ben Pedell for RN102. The RN104 shares the same Hynix H27U1G8F2BTR NAND flash and setup. This patch is based on Ben's fix for RN102. Fixes: 0373a558 ("ARM: mvebu: Enable NAND controller in ReadyNAS 104 .dts file") Signed-off-by:
-
Andrew Lunn authored
commit 4f5e01e9 upstream. During the conversion of boards to use DT to instantiate Distributed Switch Architecture, nobody volunteered to test. As to be expected, the conversion was flawed. Testers and access to hardware has now become available, and this patch hopefully fixes the problems. dsa,mii-bus must be a phandle to the top level mdio node, not the port specific subnode of the mdio device. dsa,ethernet must be a phandle to the port subnode within the ethernet DT node, not the ethernet node. Don't pinctrl hog the card detect gpio for mvsdio. Rename the .dts files to make it clearer which file is for the Z0 stepping and which for the A0 or later stepping. Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Cc: seugene@marvell.com Tested-by:
Eugene Sanivsky <seugene@marvell.com> Fixes: e2eaa339: ("ARM: Kirkwood: convert rd88f6281-setup.c to DT.") Fixes: e7c8f380: ("ARM: kirkwood: Convert mv88f6281gtw_ge switch setup to DT") Link: https://lkml.kernel.org/r/1409592941-22244-1-git-send-email-andrew@lunn.chSigned-off-by:
-
Ludovic Desroches authored
commit cfa1950e upstream. When introducing support for sama5d3, the write to PMC_PCDR register has been accidentally removed. Reported-by:
Nathalie Cyrille <nathalie.cyrille@atmel.com> Signed-off-by:
Ludovic Desroches <ludovic.desroches@atmel.com> Signed-off-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Andreas Henriksson authored
commit b65e0fb3 upstream. As discovered on a custom board similar to at91sam9263ek and basing its devicetree on that one apparently the pin muxing doesn't get set up properly. This was discovered since the custom boards u-boot does funky stuff with the pin muxing and leaved it set to SPI which made the MMC driver not work under Linux. The fix is simply to define the given configuration as the default. This probably worked by pure luck before, but it's better to make the muxing explicitly set. Signed-off-by:
Andreas Henriksson <andreas.henriksson@endian.se> Acked-by:
Boris Brezillon <boris.brezillon@free-electrons.com> Signed-off-by:
-
David Dueck authored
commit 0a51d644 upstream. Otherwise the clock for can0 will never get enabled. Signed-off-by:
David Dueck <davidcdueck@googlemail.com> Signed-off-by:
Anthony Harivel <anthony.harivel@emtrion.de> Acked-by:
-
David Henningsson authored
commit fb54a645 upstream. Without this terminating entry, the pin matching would continue across random memory until a zero or a non-matching entry was found. The result being that in some cases, the pin quirk would not be applied correctly. Signed-off-by:
David Henningsson <david.henningsson@canonical.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Takashi Iwai authored
commit b1974f96 upstream. We implemented in a wrong way for mute LED on Lenovo Ideapad; the bit must be flipped. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=16373 Fixes: 3e887f37 ('ALSA: hda - Add mute LED support to Lenovo Ideapad') Signed-off-by:
-
Anssi Hannula authored
commit 6acce400 upstream. The ELD ALSA control change event is sent by hdmi_present_sense() when eld_changed is true. Currently, it is only true when the ELD buffer contents have been modified. However, the user-visible ELD controls also change to a zero-length value and back when eld_valid is unset/set, and no event is currently sent in such cases (such as when unplugging or replugging a sink). Fix the code to always set eld_changed if eld_valid value is changed, and therefore to always send the change event when the user-visible value changes. Signed-off-by:
Anssi Hannula <anssi.hannula@iki.fi> Cc: David Henningsson <david.henningsson@canonical.com> Signed-off-by:
-
Vlad Catoi authored
commit f0b127fb upstream. Adding support for Steinberg UR22 USB interface via quirks table patch See Ubuntu bug report: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1317244 Also see threads: http://linux-audio.4202.n7.nabble.com/Support-for-Steinberg-UR22-Yamaha-USB-chipset-0499-1509-tc82888.html#a82917 http://www.steinberg.net/forums/viewtopic.php?t=62290 Tested by at least 4 people judging by the threads. Did not test MIDI interface, but audio output and capture both are functional. Built 3.17 kernel with this driver on Ubuntu 14.04 & tested with mpg123 Patch applied to 3.13 Ubuntu kernel works well enough for daily use. Signed-off-by:
Vlad Catoi <vladcatoi@gmail.com> Acked-by:
Clemens Ladisch <clemens@ladisch.de> Signed-off-by:
-
Harsha Priya authored
commit b450b17c upstream. This patch sets the headphones mode to default before suspending which helps avoid the pop noise on headphones Signed-off-by:
Harsha Priya <harshapriya.n@intel.com> Signed-off-by:
-
Takashi Iwai authored
commit 95926035 upstream. The emu10k1 voice allocator takes voice_lock spinlock. When there is no empty stream available, it tries to release a voice used by synth, and calls get_synth_voice. The callback function, snd_emu10k1_synth_get_voice(), however, also takes the voice_lock, thus it deadlocks. The fix is simply removing the voice_lock holds in snd_emu10k1_synth_get_voice(), as this is always called in the spinlock context. Reported-and-tested-by:
Arthur Marsh <arthur.marsh@internode.on.net> Signed-off-by:
-
Takashi Sakamoto authored
commit 3f403286 upstream. This patch fixes a failure to open PCM device with -ENOSYS in Terratec Phase 88. Terratec Phase 88 has two Selector Function Blocks of AVC Audio subunit to switch source of clock. One is to switch internal/external for the source and another is to switch word/spdif for the external clock. The IDs for these Selector Function Blocks are 9 and 8. But in current implementation they're 0 and 0. Reported-by:
András Murányi <muranyia@gmail.com> Tested-by:
Takashi Sakamoto <o-takashi@sakamocchi.jp> Signed-off-by:
-
Anatol Pomozov authored
commit a011e213 upstream. This avoids following kernel crash when try to playback on arm64 [ 107.497203] [<ffffffc00046b310>] snd_pcm_mmap_data_fault+0x90/0xd4 [ 107.503405] [<ffffffc0001541ac>] __do_fault+0xb0/0x498 [ 107.508565] [<ffffffc0001576a0>] handle_mm_fault+0x224/0x7b0 [ 107.514246] [<ffffffc000092640>] do_page_fault+0x11c/0x310 [ 107.519738] [<ffffffc000081100>] do_mem_abort+0x38/0x98 Tested: backported to 3.14 and tried to playback on arm64 machine Signed-off-by:
Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by:
-
Victor Kamensky authored
commit 971a5b6f upstream. The compat_elf_prpsinfo structure does not match the arch/arm struct elf_pspsinfo definition. As result NT_PRPSINFO note in core file created by arm64 kernel for aarch32 (compat) process has wrong size. So gdb cannot display command that caused process crash. Fix is to change size of __compat_uid_t, __compat_gid_t so it would match size of similar fields in arch/arm case. Signed-off-by:
Victor Kamensky <victor.kamensky@linaro.org> Acked-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Catalin Marinas <catalin.marinas@arm.com> Signed-off-by:
-
Dmitry Kasatkin authored
commit b151d6b0 upstream. On ima_file_free(), newly created empty files are not labeled with an initial security.ima value, because the iversion did not change. Commit dff6efc3 "fs: fix iversion handling" introduced a change in iversion behavior. To verify this change use the shell command: $ (exec >foo) $ getfattr -h -e hex -d -m security foo This patch defines the IMA_NEW_FILE flag. The flag is initially set, when IMA detects that a new file is created, and subsequently checked on the ima_file_free() hook to set the initial security.ima value. Signed-off-by:
Dmitry Kasatkin <d.kasatkin@samsung.com> Signed-off-by:
Mimi Zohar <zohar@linux.vnet.ibm.com> Signed-off-by:
-
Dmitry Kasatkin authored
commit 27cd1fc3 upstream. 3.16 commit aad4f8bb 'switch simple generic_file_aio_read() users to ->read_iter()' replaced ->aio_read with ->read_iter in most of the file systems and introduced new_sync_read() as a replacement for do_sync_read(). Most of file systems set '->read' and ima_kernel_read is not affected. When ->read is not set, this patch adopts fallback call changes from the vfs_read. Signed-off-by:
-
Gavin Shan authored
commit 22fca179 upstream. The problem was reported by Carol: In the scenario of passing mlx4 adapter to guest, EEH error could be recovered successfully. When returning the device back to host, the driver (mlx4_core.ko) couldn't be loaded successfully because of error number -5 (-EIO) returned from mlx4_get_ownership(), which hits offlined PCI device. The root cause is that we missed to put the affected devices into normal state on clearing PE isolated state right after PE reset. The patch fixes above issue by putting the affected devices to normal state when clearing PE isolated state in eeh_pe_state_clear(). Reported-by:
Carol L. Soto <clsoto@us.ibm.com> Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Alexey Kardashevskiy authored
commit 9410e018 upstream. rtas_call() accepts and returns values in CPU endianness. The ddw_query_response and ddw_create_response structs members are defined and treated as BE but as they are passed to rtas_call() as (u32 *) and they get byteswapped automatically, the data is CPU-endian. This fixes ddw_query_response and ddw_create_response definitions and use. of_read_number() is designed to work with device tree cells - it assumes the input is big-endian and returns data in CPU-endian. However due to the ddw_create_response struct fix, create.addr_hi/lo are already CPU-endian so do not byteswap them. ddw_avail is a pointer to the "ibm,ddw-applicable" property which contains 3 cells which are big-endian as it is a device tree. rtas_call() accepts a RTAS token in CPU-endian. This makes use of of_property_read_u32_array to byte swap and avoid the need for a number of be32_to_cpu calls. Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> [aik: folded Anton's patch with of_property_read_u32_array] Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Acked-by:
Anton Blanchard <anton@samba.org> Signed-off-by:
-
Catalin Marinas authored
commit 76835b0e upstream. Commit b0c29f79 (futexes: Avoid taking the hb->lock if there's nothing to wake up) changes the futex code to avoid taking a lock when there are no waiters. This code has been subsequently fixed in commit 11d4616b (futex: revert back to the explicit waiter counting code). Both the original commit and the fix-up rely on get_futex_key_refs() to always imply a barrier. However, for private futexes, none of the cases in the switch statement of get_futex_key_refs() would be hit and the function completes without a memory barrier as required before checking the "waiters" in futex_wake() -> hb_waiters_pending(). The consequence is a race with a thread waiting on a futex on another CPU, allowing the waker thread to read "waiters == 0" while the waiter thread to have read "futex_val == locked" (in kernel). Without this fix, the problem (user space deadlocks) can be seen with Android bionic's mutex implementation on an arm64 multi-cluster system. Signed-off-by:
Matteo Franchin <Matteo.Franchin@arm.com> Fixes: b0c29f79 (futexes: Avoid taking the hb->lock if there's nothing to wake up) Acked-by:
Davidlohr Bueso <dave@stgolabs.net> Tested-by:
Mike Galbraith <umgwanakikbuti@gmail.com> Cc: Darren Hart <dvhart@linux.intel.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Ingo Molnar <mingo@kernel.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Daniel Glöckner authored
commit a882b14f upstream. Commit b5ada460 ("drivers/rtc/rtc-cmos.c: fix compilation warning when !CONFIG_PM_SLEEP") broke wakeup from S5 by making cmos_poweroff a nop unless CONFIG_PM_SLEEP was defined. Fix this by restricting the #ifdef to cmos_resume and restoring the old dependency on CONFIG_PM for cmos_suspend and cmos_poweroff. Signed-off-by:
Daniel Glöckner <daniel-gl@gmx.net> Cc: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: Alessandro Zummo <a.zummo@towertech.it> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
-
Sasha Levin authored
commit 71458cfc upstream. We're missing include/linux/compiler-gcc5.h which is required now because gcc branched off to v5 in trunk. Just copy the relevant bits out of include/linux/compiler-gcc4.h, no new code is added as of now. This fixes a build error when using gcc 5. Signed-off-by:
Sasha Levin <sasha.levin@oracle.com> Signed-off-by:
-
Yann Droneaud authored
commit 0b37e097 upstream. According to commit 80af2588 ("fanotify: groups can specify their f_flags for new fd"), file descriptors created as part of file access notification events inherit flags from the event_f_flags argument passed to syscall fanotify_init(2)[1]. Unfortunately O_CLOEXEC is currently silently ignored. Indeed, event_f_flags are only given to dentry_open(), which only seems to care about O_ACCMODE and O_PATH in do_dentry_open(), O_DIRECT in open_check_o_direct() and O_LARGEFILE in generic_file_open(). It's a pity, since, according to some lookup on various search engines and http://codesearch.debian.net/, there's already some userspace code which use O_CLOEXEC: - in systemd's readahead[2]: fanotify_fd = fanotify_init(FAN_CLOEXEC|FAN_NONBLOCK, O_RDONLY|O_LARGEFILE|O_CLOEXEC|O_NOATIME); - in clsync[3]: #define FANOTIFY_EVFLAGS (O_LARGEFILE|O_RDONLY|O_CLOEXEC) int fanotify_d = fanotify_init(FANOTIFY_FLAGS, FANOTIFY_EVFLAGS); - in examples [4] from "Filesystem monitoring in the Linux kernel" article[5] by Aleksander Morgado: if ((fanotify_fd = fanotify_init (FAN_CLOEXEC, O_RDONLY | O_CLOEXEC | O_LARGEFILE)) < 0) Additionally, since commit 48149e9d ("fanotify: check file flags passed in fanotify_init"). having O_CLOEXEC as part of fanotify_init() second argument is expressly allowed. So it seems expected to set close-on-exec flag on the file descriptors if userspace is allowed to request it with O_CLOEXEC. But Andrew Morton raised[6] the concern that enabling now close-on-exec might break existing applications which ask for O_CLOEXEC but expect the file descriptor to be inherited across exec(). In the other hand, as reported by Mihai Dontu[7] close-on-exec on the file descriptor returned as part of file access notify can break applications due to deadlock. So close-on-exec is needed for most applications. More, applications asking for close-on-exec are likely expecting it to be enabled, relying on O_CLOEXEC being effective. If not, it might weaken their security, as noted by Jan Kara[8]. So this patch replaces call to macro get_unused_fd() by a call to function get_unused_fd_flags() with event_f_flags value as argument. This way O_CLOEXEC flag in the second argument of fanotify_init(2) syscall is interpreted and close-on-exec get enabled when requested. [1] http://man7.org/linux/man-pages/man2/fanotify_init.2.html [2] http://cgit.freedesktop.org/systemd/systemd/tree/src/readahead/readahead-collect.c?id=v208#n294 [3] https://github.com/xaionaro/clsync/blob/v0.2.1/sync.c#L1631 https://github.com/xaionaro/clsync/blob/v0.2.1/configuration.h#L38 [4] http://www.lanedo.com/~aleksander/fanotify/fanotify-example.c [5] http://www.lanedo.com/2013/filesystem-monitoring-linux-kernel/ [6] http://lkml.kernel.org/r/20141001153621.65e9258e65a6167bf2e4cb50@linux-foundation.org [7] http://lkml.kernel.org/r/20141002095046.3715eb69@mdontu-l [8] http://lkml.kernel.org/r/20141002104410.GB19748@quack.suse.cz Link: http://lkml.kernel.org/r/cover.1411562410.git.ydroneaud@opteya.comSigned-off-by:
Yann Droneaud <ydroneaud@opteya.com> Reviewed-by:
Jan Kara <jack@suse.cz> Reviewed by: Heinrich Schuchardt <xypron.glpk@gmx.de> Tested-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Mihai Don\u021bu <mihai.dontu@gmail.com> Cc: Pádraig Brady <P@draigBrady.com> Cc: Heinrich Schuchardt <xypron.glpk@gmx.de> Cc: Jan Kara <jack@suse.cz> Cc: Valdis Kletnieks <Valdis.Kletnieks@vt.edu> Cc: Michael Kerrisk-manpages <mtk.manpages@gmail.com> Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de> Cc: Richard Guy Briggs <rgb@redhat.com> Cc: Eric Paris <eparis@redhat.com> Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Michael Kerrisk <mtk.manpages@gmail.com> Signed-off-by:
-
Junxiao Bi authored
commit 934f3072 upstream. commit 21caf2fc ("mm: teach mm by current context info to not do I/O during memory allocation") introduces PF_MEMALLOC_NOIO flag to avoid doing I/O inside memory allocation, __GFP_IO is cleared when this flag is set, but __GFP_FS implies __GFP_IO, it should also be cleared. Or it may still run into I/O, like in superblock shrinker. And this will make the kernel run into the deadlock case described in that commit. See Dave Chinner's comment about io in superblock shrinker: Filesystem shrinkers do indeed perform IO from the superblock shrinker and have for years. Even clean inodes can require IO before they can be freed - e.g. on an orphan list, need truncation of post-eof blocks, need to wait for ordered operations to complete before it can be freed, etc. IOWs, Ext4, btrfs and XFS all can issue and/or block on arbitrary amounts of IO in the superblock shrinker context. XFS, in particular, has been doing transactions and IO from the VFS inode cache shrinker since it was first introduced.... Fix this by clearing __GFP_FS in memalloc_noio_flags(), this function has masked all the gfp_mask that will be passed into fs for the processes setting PF_MEMALLOC_NOIO in the direct reclaim path. v1 thread at: https://lkml.org/lkml/2014/9/3/32Signed-off-by:
Junxiao Bi <junxiao.bi@oracle.com> Cc: Dave Chinner <david@fromorbit.com> Cc: joyce.xue <xuejiufei@huawei.com> Cc: Ming Lei <ming.lei@canonical.com> Cc: Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Johan Hedberg authored
commit 5eb596f5 upstream. We can only determine the final security level when both pairing request and response have been exchanged. When initiating pairing the starting target security level is set to MEDIUM unless explicitly specified to be HIGH, so that we can still perform pairing even if the remote doesn't have MITM capabilities. However, once we've received the pairing response we should re-consult the remote and local IO capabilities and upgrade the target security level if necessary. Without this patch the resulting Long Term Key will occasionally be reported to be unauthenticated when it in reality is an authenticated one. Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Marcel Holtmann <marcel@holtmann.org> Signed-off-by:
-
Champion Chen authored
commit 85560c4a upstream. Suspend could fail for some platforms because btusb_suspend==> btusb_stop_traffic ==> usb_kill_anchored_urbs. When btusb_bulk_complete returns before system suspend and resubmits an URB, the system cannot enter suspend state. Signed-off-by:
Champion Chen <champion_chen@realsil.com.cn> Signed-off-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Johan Hedberg authored
commit 72c6fb91 upstream. The l2cap_create_le_flowctl_pdu() function that l2cap_segment_le_sdu() calls is perfectly capable of doing packet fragmentation if given bigger PDUs than the HCI buffers allow. Forcing the PDU length based on the HCI MTU (conn->mtu) would therefore needlessly strict operation on hardware with limited LE buffers (e.g. both Intel and Broadcom seem to have this set to just 27 bytes). This patch removes the restriction and makes it possible to send PDUs of the full length that the remote MPS value allows. Signed-off-by:
-
Loic Poulain authored
commit 4807b518 upstream. In this expression: seq = (seq - 1) % 8 seq (u8) is implicitly converted to an int in the arithmetic operation. So if seq value is 0, operation is ((0 - 1) % 8) => (-1 % 8) => -1. The new seq value is 0xff which is an invalid ACK value, we expect 0x07. It leads to frequent dropped ACK and retransmission. Fix this by using '&' binary operator instead of '%'. Signed-off-by:
Loic Poulain <loic.poulain@intel.com> Signed-off-by:
-
Felix Fietkau authored
commit 171cdab8 upstream. This reverts commit 09efc563 I've received reports that this change is decreasing throughput in some rare conditions on an AR9280 based device Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Signed-off-by:
John W. Linville <linville@tuxdriver.com> Signed-off-by:
-
