- 05 Mar, 2022 29 commits
-
-
David S. Miller authored
Robert Hancock says: ==================== NAPI/GRO support for axienet driver Add support for NAPI and GRO receive in the Xilinx AXI Ethernet driver, and some other related cleanups. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Robert Hancock authored
Add the ability to configure the RX/TX coalesce timer with ethtool. Change default setting to scale with the clock rate rather than being a fixed number of clock cycles. Signed-off-by:
Robert Hancock <robert.hancock@calian.com> Signed-off-by:
-
Robert Hancock authored
Now that NAPI has been implemented, the hardware interrupt mitigation mechanism is not needed to avoid excessive interrupt load in most cases. Reduce the default RX interrupt threshold to 1 to reduce introduced latency. This can be increased with ethtool if desired if some applications still want to reduce interrupts. Signed-off-by:
-
Robert Hancock authored
Implement NAPI and GRO receive. In addition to better performance, this also avoids handling RX packets in hard IRQ context, which reduces the IRQ latency impact to other devices. Signed-off-by:
-
Robert Hancock authored
When the RX or TX coalesce count is set to 1, there's no point in setting the delay timer value since an interrupt will already be raised on every packet, and the delay interrupt just causes extra pointless interrupts. Signed-off-by:
-
Robert Hancock authored
Simplify the DMA error handling process, and remove some duplicated code between the DMA error handling and the stop function. Signed-off-by:
-
Robert Hancock authored
Instead of using lp->ndev.parent to find the correct device to use for DMA API calls, just use the dev attribute in the device structure. Signed-off-by:
-
Robert Hancock authored
If a memory allocation error occurred during an attempt to refill a slot in the RX ring after the packet was received, the hardware tail pointer would still have been updated to point to or past the slot which remained marked as previously completed. This would likely result in the DMA engine raising an error when it eventually tried to use that slot again. If a slot cannot be refilled, then just stop processing and do not move the tail pointer past it. On the next attempt, we should skip receiving the packet from the empty slot and just try to refill it again. This failure mode has not actually been observed, but was found as part of other driver updates. Fixes: 8a3b7a25 ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver") Signed-off-by:
-
David S. Miller authored
Luiz Angelo Daros de Luca says: ==================== net: dsa: realtek: add rtl8_4t tag This patch series adds support for rtl8_4t tag. It is a variant of rtl8_4 tag, with identical values but placed at the end of the packet (before CRC). It forces checksum in software before adding the tag as those extra bytes at the end of the packet would be summed together with the rest of the payload. When the switch removes the tag before sending the packet to the network, that checksum will not match. It might be useful to diagnose or avoid checksum offload issues. With an ethertype tag like rtl8_4, the cpu port ethernet driver must work with cksum_start and chksum_offset to correctly calculate checksums. If not, the checksum field will be broken (it will contain the fake ip header sum). In those cases, using 'rtl8_4t' might be an alternative way to avoid checksum offload, either using runtime or device-tree property. Regards, Luiz v4-v5) - tags in alphabetical order in dsa_port.yaml - remove ret var from rtl8365mb_change_tag_protocol - Comment typos fixes v3-v4) - added rtl8_4 and rtl8_4t to dsa_port.yaml - removed generic considerations about checksum problems with DSA tags. They belong to Documentation/networking/dsa/dsa.rst v2-v3) - updated tag documentation (file header) - do not remove position and format from rtl8365mb_cpu - reinstate cpu to rtl8365mb - moved rtl8365mb_change_tag_protocol after rtl8365mb_cpu_config - do not modify rtl8365mb_cpu_config() logic - remove cpu arg from rtl8365mb_cpu_config(); get it from priv - dropped tag_protocol from rtl8365mb. It is now derived from cpu->position. - init cpu struct before dsa_register as default tag must be already defined before dsa_register() - fix formatting issues v1-v2) - remove mention to tail tagger, use trailing tagger. - use void* instead of char* for pointing to tag beginning - use memcpy to avoid problems with unaligned tags - calculate checksum if it still pending - keep in-use tag protocol in memory instead of reading from switch register ==================== Signed-off-by: -
Luiz Angelo Daros de Luca authored
The trailing tag is also supported by this family. The default is still rtl8_4 but now the switch supports changing the tag to rtl8_4t. Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631c). Signed-off-by:
Luiz Angelo Daros de Luca <luizluca@gmail.com> Reviewed-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Reviewed-by:
Vladimir Oltean <olteanv@gmail.com> Signed-off-by:
-
Luiz Angelo Daros de Luca authored
Realtek switches supports the same tag both before ethertype or between payload and the CRC. Signed-off-by:
-
Luiz Angelo Daros de Luca authored
Realtek rtl8365mb DSA driver can use these two tag formats. Cc: devicetree@vger.kernel.org Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Jakub Kicinski authored
Mat Martineau says: ==================== mptcp: Selftest refinements and a new test Patches 1 and 11 improve the printed output of the mptcp_join.sh selftest. Patches 2-8 add a test for the MP_FASTCLOSE option, including prerequisite changes like additional MPTCP MIBs. Patches 9-10 add some groundwork for upcoming tests. ==================== Link: https://lore.kernel.org/r/20220304193636.219315-1-mathew.j.martineau@linux.intel.comSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Geliang Tang authored
This patch updated the output info of chk_rm_nr. Renamed 'sf' to 'rmsf', which means 'remove subflow'. Added the display of whether the inverted namespaces has been used to check the mib counters. The new output looks like this: 002 remove multiple subflows syn[ ok ] - synack[ ok ] - ack[ ok ] rm [ ok ] - rmsf [ ok ] 003 remove single address syn[ ok ] - synack[ ok ] - ack[ ok ] add[ ok ] - echo [ ok ] rm [ ok ] - rmsf [ ok ] invert Signed-off-by:Geliang Tang <geliang.tang@suse.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Geliang Tang authored
This patch added five more arguments for chk_join_nr(). The default values of them are all zero. The first two, csum_ns1 and csum_ns1, are passed to chk_csum_nr(), to check the mib counters of the checksum errors in ns1 and ns2. A '+' can be added into this two arguments to represent that multiple checksum errors are allowed when doing this check. For example, chk_csum_nr "" +2 +2 indicates that two or more checksum errors are allowed in both ns1 and ns2. The remaining two, fail_nr and rst_nr, are passed to chk_fail_nr() and chk_rst_nr() respectively, to check the sending and receiving mib counters of MP_FAIL and MP_RST. Also did some cleanups in chk_fail_nr(), renamed two local variables and updated the output message. Signed-off-by: -
Geliang Tang authored
This patch added the invert bytes check for the output data in check_transfer(). Instead of the file mismatch error: [ FAIL ] file received by server does not match (in, out): -rw------- 1 root root 45643832 Jan 16 15:04 /tmp/tmp.9xpM6Paivv Trailing bytes are: MPTCP_TEST_FILE_END_MARKER -rw------- 1 root root 45643832 Jan 16 15:04 /tmp/tmp.wnz1Yp4u7Z Trailing bytes are: MPTCP_TEST_FILE_END_MARKER Print out the inverted bytes like this: file received by server has inverted byte at 7454789 file received by server has inverted byte at 7454790 file received by server has inverted byte at 7454791 file received by server has inverted byte at 7454792 Signed-off-by:
-
Geliang Tang authored
This patch added the self test for MP_FASTCLOSE. Reused the argument addr_nr_ns2 of do_transfer() to pass the extra arguments '-I 2' to mptcp_connect commands. Then mptcp_connect disconnected the connections to trigger the MP_FASTCLOSE sending and receiving. Used chk_fclose_nr to check the MP_FASTCLOSE mibs and used chk_rst_nr to check the MP_RST mibs. This test used the test_linkfail value to make 1024KB test files. The output looks like this: Created /tmp/tmp.XB8sfv1hJ0 (size 1024 KB) containing data sent by client Created /tmp/tmp.RtTDbzqrXI (size 1024 KB) containing data sent by server 001 fastclose test syn[ ok ] - synack[ ok ] - ack[ ok ] ctx[ ok ] - fclzrx[ ok ] rtx[ ok ] - rstrx [ ok ] invert Signed-off-by: -
Geliang Tang authored
This patch reused the test_linkfail values above 2 to make test files with the given sizes (KB) for both the client side and the server side. It's useful for the test cases using different file sizes. Signed-off-by:
-
Geliang Tang authored
Instead of using a global variable mptcp_connect, this patch added a new local variable extra_args in do_transfer() to store the extra arguments passing to the mptcp_connect commands. This patch also renamed the speed level 'least' to 'speed_*'. This more flexible way can avoid the need to add new speed levels in the future. Signed-off-by:
-
Geliang Tang authored
This patch added a new function chk_rst_nr() to check the numbers of the MP_RST sending and receiving mibs. Showed in the output whether the inverted namespaces check order is used. Since if we pass -Cz to mptcp_join.sh, the MP_RST information is showed twice. Signed-off-by:
-
Geliang Tang authored
This patch added two more mibs for MP_RST, MPTCP_MIB_MPRSTTX for the MP_RST sending and MPTCP_MIB_MPRSTRX for the MP_RST receiving. Signed-off-by:
-
Geliang Tang authored
This patch added a new function chk_fclose_nr() to check the numbers of the MP_FASTCLOSE sending and receiving mibs. Signed-off-by:
-
Geliang Tang authored
This patch added two more mibs for MP_FASTCLOSE, MPTCP_MIB_MPFASTCLOSETX for the MP_FASTCLOSE sending and MPTCP_MIB_MPFASTCLOSERX for receiving. Also added a debug log for MP_FASTCLOSE receiving, printed out the recv_key of MP_FASTCLOSE in mptcp_parse_option to show that MP_RST is received. Signed-off-by:
-
Geliang Tang authored
The number of self tests in mptcp_join.sh will soon be more than 100, the output alignment is no longer OK. This patch adjusted it. Signed-off-by:
-
Meng Tang authored
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static allocation of IRQ resources in DT core code, this causes an issue when using hierarchical interrupt domains using "interrupts" property in the node as this bypassed the hierarchical setup and messed up the irq chaining. In preparation for removal of static setup of IRQ resource from DT core code use platform_get_irq(). Signed-off-by:
Meng Tang <tangmeng@uniontech.com> Link: https://lore.kernel.org/r/20220303100815.25605-1-tangmeng@uniontech.comSigned-off-by:
-
Jonathan Lemon authored
On the debug summary page, show the /dev/ttyS<port> mapping. Signed-off-by:
Jonathan Lemon <jonathan.lemon@gmail.com> Link: https://lore.kernel.org/r/20220304054615.1737-1-jonathan.lemon@gmail.comSigned-off-by:
-
Horatiu Vultur authored
The variables 'res' inside the functions sparx5_ptp_get_1ppm and sparx5_ptp_get_nominal_value was not initialized. So in case of the default case of the switch after, it would return an uninitialized variable. This makes also the clang builds to failed. Fixes: 0933bd04 ("net: sparx5: Add support for ptp clocks") Signed-off-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20220304140918.3356873-1-horatiu.vultur@microchip.comSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'for-net-next-2022-03-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next Luiz Augusto von Dentz says: ==================== bluetooth-next pull request for net-next: - Add new PID/VID (0x13d3/0x3567) for MT7921 - Add new PID/VID (0x2550/0x8761) for Realtek 8761BU - Add support for LG LGSBWAC02 (MT7663BUN) - Add support for BCM43430A0 and BCM43430A1 - Add support for Intel Madison Peak (MsP2) * tag 'for-net-next-2022-03-04' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next: (21 commits) Bluetooth: btusb: Add another Realtek 8761BU Bluetooth: hci_bcm: add BCM43430A0 & BCM43430A1 Bluetooth: use memset avoid memory leaks Bluetooth: btmtksdio: Fix kernel oops when sdio suspend. Bluetooth: btusb: Add a new PID/VID 13d3/3567 for MT7921 Bluetooth: move adv_instance_cnt read within the device lock Bluetooth: hci_event: Add missing locking on hdev in hci_le_ext_adv_term_evt Bluetooth: btusb: Make use of of BIT macro to declare flags Bluetooth: Fix not checking for valid hdev on bt_dev_{info,warn,err,dbg} Bluetooth: mediatek: fix the conflict between mtk and msft vendor event Bluetooth: mt7921s: support bluetooth reset mechanism Bluetooth: make array bt_uuid_any static const Bluetooth: 6lowpan: No need to clear memory twice Bluetooth: btusb: Improve stability for QCA devices Bluetooth: btusb: add support for LG LGSBWAC02 (MT7663BUN) Bluetooth: btusb: Add support for Intel Madison Peak (MsP2) device Bluetooth: Improve skb handling in mgmt_device_connected() Bluetooth: Fix skb allocation in mgmt_remote_name() & mgmt_device_connected() Bluetooth: mgmt: Remove unneeded variable Bluetooth: hci_sync: fix undefined return of hci_disconnect_all_sync() ... ==================== Link: https://lore.kernel.org/r/20220304193919.649815-1-luiz.dentz@gmail.comSigned-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Daniel Borkmann says: ==================== pull-request: bpf-next 2022-03-04 We've added 32 non-merge commits during the last 14 day(s) which contain a total of 59 files changed, 1038 insertions(+), 473 deletions(-). The main changes are: 1) Optimize BPF stackmap's build_id retrieval by caching last valid build_id, as consecutive stack frames are likely to be in the same VMA and therefore have the same build id, from Hao Luo. 2) Several improvements to arm64 BPF JIT, that is, support for JITing the atomic[64]_fetch_add, atomic[64]_[fetch_]{and,or,xor} and lastly atomic[64]_{xchg|cmpxchg}. Also fix the BTF line info dump for JITed programs, from Hou Tao. 3) Optimize generic BPF map batch deletion by only enforcing synchronize_rcu() barrier once upon return to user space, from Eric Dumazet. 4) For kernel build parse DWARF and generate BTF through pahole with enabled multithreading, from Kui-Feng Lee. 5) BPF verifier usability improvements by making log info more concise and replacing inv with scalar type name, from Mykola Lysenko. 6) Two follow-up fixes for BPF prog JIT pack allocator, from Song Liu. 7) Add a new Kconfig to allow for loading kernel modules with non-matching BTF type info; their BTF info is then removed on load, from Connor O'Brien. 8) Remove reallocarray() usage from bpftool and switch to libbpf_reallocarray() in order to fix compilation errors for older glibc, from Mauricio Vásquez. 9) Fix libbpf to error on conflicting name in BTF when type declaration appears before the definition, from Xu Kuohai. 10) Fix issue in BPF preload for in-kernel light skeleton where loaded BPF program fds prevent init process from setting up fd 0-2, from Yucong Sun. 11) Fix libbpf reuse of pinned perf RB map when max_entries is auto-determined by libbpf, from Stijn Tintel. 12) Several cleanups for libbpf and a fix to enforce perf RB map #pages to be non-zero, from Yuntao Wang. * https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (32 commits) bpf: Small BPF verifier log improvements libbpf: Add a check to ensure that page_cnt is non-zero bpf, x86: Set header->size properly before freeing it x86: Disable HAVE_ARCH_HUGE_VMALLOC on 32-bit x86 bpf, test_run: Fix overflow in XDP frags bpf_test_finish selftests/bpf: Update btf_dump case for conflicting names libbpf: Skip forward declaration when counting duplicated type names bpf: Add some description about BPF_JIT_ALWAYS_ON in Kconfig bpf, docs: Add a missing colon in verifier.rst bpf: Cache the last valid build_id libbpf: Fix BPF_MAP_TYPE_PERF_EVENT_ARRAY auto-pinning bpf, selftests: Use raw_tp program for atomic test bpf, arm64: Support more atomic operations bpftool: Remove redundant slashes bpf: Add config to allow loading modules with BTF mismatches bpf, arm64: Feed byte-offset into bpf line info bpf, arm64: Call build_prologue() first in first JIT pass bpf: Fix issue with bpf preload module taking over stdout/stdin of kernel. bpftool: Bpf skeletons assert type sizes bpf: Cleanup comments ... ==================== Link: https://lore.kernel.org/r/20220304164313.31675-1-daniel@iogearbox.netSigned-off-by:
-
- 04 Mar, 2022 11 commits
-
-
Helmut Grohne authored
This device is sometimes wrapped with a label "EDUP". T: Bus=01 Lev=02 Prnt=02 Port=02 Cnt=03 Dev#=107 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=2550 ProdID=8761 Rev= 2.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00E04C239987 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by:
Helmut Grohne <helmut@subdivi.de> Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1955351Signed-off-by:
Marcel Holtmann <marcel@holtmann.org>
-
Luca Weiss authored
Add the compatible for BCM43430A0 bluetooth used in lg-lenok and BCM43430A1 used in asus-sparrow. Signed-off-by:
Luca Weiss <luca@z3ntu.xyz> Signed-off-by:
-
Minghao Chi (CGEL ZTE) authored
Use memset to initialize structs to prevent memory leaks in l2cap_ecred_connect Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi (CGEL ZTE) <chi.minghao@zte.com.cn> Signed-off-by:
-
Yake Yang authored
Do not kfree the skb when the skb failed to send with __hci_cmd_sync 2435.241210] Call trace: [ 2435.241224] kfree_skb+0x20/0x140 [ 2435.241240] btmtksdio_sdio_wakeup+0x8c/0xcc [ 2435.241360] hci_suspend_notifier+0x108/0x184 [ 2435.241377] notifier_call_chain_robust+0x58/0xd8 [ 2435.241390] blocking_notifier_call_chain_robust+0x54/0x84 [ 2435.241402] pm_notifier_call_chain_robust+0x2c/0x4c [ 2435.241414] suspend_prepare+0x40/0x238 [ 2435.241425] enter_state+0xec/0x3a8 [ 2435.241436] pm_suspend+0x60/0xcc [ 2435.241446] state_store+0xb8/0x114 [ 2435.241460] kobj_attr_store+0x18/0x2c [ 2435.241473] sysfs_kf_write+0x44/0x58 [ 2435.241486] kernfs_fop_write_iter+0xf4/0x190 [ 2435.241500] vfs_write+0x2b0/0x2e4 [ 2435.241511] ksys_write+0x80/0xec [ 2435.241523] __arm64_sys_write+0x24/0x30 [ 2435.241538] el0_svc_common+0xf0/0x1d8 [ 2435.241550] do_el0_svc_compat+0x28/0x54 [ 2435.241564] el0_svc_compat+0x10/0x1c [ 2435.241574] el0_sync_compat_handler+0xa8/0xcc [ 2435.241586] el0_sync_compat+0x188/0x1c0 [ 2435.241606] Code: a9014ff4 910003fd b40002c0 aa0003f3 (b84d4c08) [ 2435.241619] ---[ end trace d496539b850baf14 ]--- Fixes: ce64b3e9 ("Bluetooth: mt7921s: Support wake on bluetooth") Co-developed-by:
Sean Wang <sean.wang@mediatek.com> Signed-off-by:
Yake Yang <yake.yang@mediatek.com> Signed-off-by:
-
Yake Yang authored
Add VID 13D3 & PID 3567 for MediaTek MT7921 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=05 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3567 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us Co-developed-by:
-
Niels Dossche authored
The field adv_instance_cnt is always accessed within a device lock, except in the function add_advertising. A concurrent remove of an advertisement with adding another one could result in the if check "if a new instance was actually added" to not trigger, resulting in not triggering the "advertising added event". Signed-off-by:
Niels Dossche <niels.dossche@ugent.be> Signed-off-by:
-
Niels Dossche authored
Both hci_find_adv_instance and hci_remove_adv_instance have a comment above their function definition saying that these two functions require the caller to hold the hdev->lock lock. However, hci_le_ext_adv_term_evt does not acquire that lock and neither does its caller hci_le_meta_evt (hci_le_meta_evt calls hci_le_ext_adv_term_evt via an indirect function call because of the lookup in hci_le_ev_table). The other event handlers all acquire and release the hdev->lock and they follow the rule that hci_find_adv_instance and hci_remove_adv_instance must be called while holding the hdev->lock lock. The solution is to make sure hci_le_ext_adv_term_evt also acquires and releases the hdev->lock lock. The check on ev->status which logs a warning and does an early return is not covered by the lock because other functions also access ev->status without holding the lock. Signed-off-by:
-
Luiz Augusto von Dentz authored
This makes use of BIT macro when declaring BTUSB flags which makes it understand how many bits are in use and many are left. Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
This fixes attemting to print hdev->name directly which causes them to print an error: kernel: read_version:367: (efault): sock 000000006a3008f2 Signed-off-by:
-
Sean Wang authored
There is a conflict between MediaTek wmt event and msft vendor extension logic in the core layer since 145373cb ("Bluetooth: Add framework for Microsoft vendor extension") was introduced because we changed the type of mediatek wmt event to the type of msft vendor event in the driver. But the purpose we reported mediatek event to the core layer is for the diagnostic purpose with that we are able to see the full packet trace via monitoring socket with btmon. Thus, it is harmless we keep the original type of mediatek vendor event here to avoid breaking the msft extension function especially they can be supported by Mediatek chipset like MT7921 , MT7922 devices and future devices. Signed-off-by:
-
Chih-Ying Chiang authored
Implement .cmd_timeout to reset the MT7921s device via a dedicated GPIO pin when the firmware hang or the command has no response. Co-developed-by:
Mark Chen <mark-yw.chen@mediatek.com> Signed-off-by:
Chih-Ying Chiang <chih-yin.chiang@mediatek.com> Signed-off-by:
-
