- 09 Jun, 2014 40 commits
-
-
Srivatsa S. Bhat authored
commit 011e4b02 upstream. If we try to perform a kexec when the machine is in ST (Single-Threaded) mode (ppc64_cpu --smt=off), the kexec operation doesn't succeed properly, and we get the following messages during boot: [ 0.089866] POWER8 performance monitor hardware support registered [ 0.089985] power8-pmu: PMAO restore workaround active. [ 5.095419] Processor 1 is stuck. [ 10.097933] Processor 2 is stuck. [ 15.100480] Processor 3 is stuck. [ 20.102982] Processor 4 is stuck. [ 25.105489] Processor 5 is stuck. [ 30.108005] Processor 6 is stuck. [ 35.110518] Processor 7 is stuck. [ 40.113369] Processor 9 is stuck. [ 45.115879] Processor 10 is stuck. [ 50.118389] Processor 11 is stuck. [ 55.120904] Processor 12 is stuck. [ 60.123425] Processor 13 is stuck. [ 65.125970] Processor 14 is stuck. [ 70.128495] Processor 15 is stuck. [ 75.131316] Processor 17 is stuck. Note that only the sibling threads are stuck, while the primary threads (0, 8, 16 etc) boot just fine. Looking closer at the previous step of kexec, we observe that kexec tries to wakeup (bring online) the sibling threads of all the cores, before performing kexec: [ 9464.131231] Starting new kernel [ 9464.148507] kexec: Waking offline cpu 1. [ 9464.148552] kexec: Waking offline cpu 2. [ 9464.148600] kexec: Waking offline cpu 3. [ 9464.148636] kexec: Waking offline cpu 4. [ 9464.148671] kexec: Waking offline cpu 5. [ 9464.148708] kexec: Waking offline cpu 6. [ 9464.148743] kexec: Waking offline cpu 7. [ 9464.148779] kexec: Waking offline cpu 9. [ 9464.148815] kexec: Waking offline cpu 10. [ 9464.148851] kexec: Waking offline cpu 11. [ 9464.148887] kexec: Waking offline cpu 12. [ 9464.148922] kexec: Waking offline cpu 13. [ 9464.148958] kexec: Waking offline cpu 14. [ 9464.148994] kexec: Waking offline cpu 15. [ 9464.149030] kexec: Waking offline cpu 17. Instrumenting this piece of code revealed that the cpu_up() operation actually fails with -EBUSY. Thus, only the primary threads of all the cores are online during kexec, and hence this is a sure-shot receipe for disaster, as explained in commit e8e5c215 (powerpc/kexec: Fix orphaned offline CPUs across kexec), as well as in the comment above wake_offline_cpus(). It turns out that cpu_up() was returning -EBUSY because the variable 'cpu_hotplug_disabled' was set to 1; and this disabling of CPU hotplug was done by migrate_to_reboot_cpu() inside kernel_kexec(). Now, migrate_to_reboot_cpu() was originally written with the assumption that any further code will not need to perform CPU hotplug, since we are anyway in the reboot path. However, kexec is clearly not such a case, since we depend on onlining CPUs, atleast on powerpc. So re-enable cpu-hotplug after returning from migrate_to_reboot_cpu() in the kexec path, to fix this regression in kexec on powerpc. Also, wrap the cpu_up() in powerpc kexec code within a WARN_ON(), so that we can catch such issues more easily in the future. Fixes: c97102ba (kexec: migrate to reboot cpu) Signed-off-by:
Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com> Signed-off-by:
Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by:
Jiri Slaby <jslaby@suse.cz>
-
Guenter Roeck authored
commit 7998eb3d upstream. With binutils 2.24, various 64 bit builds fail with relocation errors such as arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e': (.text+0x165ee): relocation truncated to fit: R_PPC64_ADDR16_HI against symbol `interrupt_base_book3e' defined in .text section in arch/powerpc/kernel/built-in.o arch/powerpc/kernel/built-in.o: In function `exc_debug_crit_book3e': (.text+0x16602): relocation truncated to fit: R_PPC64_ADDR16_HI against symbol `interrupt_end_book3e' defined in .text section in arch/powerpc/kernel/built-in.o The assembler maintainer says: I changed the ABI, something that had to be done but unfortunately happens to break the booke kernel code. When building up a 64-bit value with lis, ori, shl, oris, ori or similar sequences, you now should use @high and @higha in place of @h and @ha. @h and @ha (and their associated relocs R_PPC64_ADDR16_HI and R_PPC64_ADDR16_HA) now report overflow if the value is out of 32-bit signed range. ie. @h and @ha assume you're building a 32-bit value. This is needed to report out-of-range -mcmodel=medium toc pointer offsets in @toc@h and @toc@ha expressions, and for consistency I did the same for all other @h and @ha relocs. Replacing @h with @high in one strategic location fixes the relocation errors. This has to be done conditionally since the assembler either supports @h or @high but not both. Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Gavin Shan authored
commit 372cf124 upstream. Resetting root port has more stuff to do than that for PCIe switch ports and we should have resetting root port done in firmware instead of the kernel itself. The problem was introduced by commit 5b2e198e ("powerpc/powernv: Rework EEH reset"). Signed-off-by:
Gavin Shan <gwshan@linux.vnet.ibm.com> Signed-off-by:
-
Horia Geanta authored
commit 27c5fb7a upstream. GFP_ATOMIC memory allocation could fail. In this case, avoid NULL pointer dereference and notify user. Cc: Kim Phillips <kim.phillips@freescale.com> Signed-off-by:
Horia Geanta <horia.geanta@freescale.com> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Olof Johansson authored
commit ce78cc07 upstream. Don't unmark the device as suspended until after it's been re-setup. The main race would be w.r.t. an i2c driver that gets resumed at the same time (asyncronously), that is allowed to do a transfer since suspended is set to 0 before reinit, but really should have seen the -EIO return instead. Signed-off-by:
Olof Johansson <olof@lixom.net> Signed-off-by:
Doug Anderson <dianders@chromium.org> Acked-by:
Kukjin Kim <kgene.kim@samsung.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Du, Wenkai authored
commit 47bb27e7 upstream. There have been "i2c_designware 80860F41:00: controller timed out" errors on a number of Baytrail platforms. The issue is caused by incorrect value in Interrupt Mask Register (DW_IC_INTR_MASK) when i2c core is being enabled. This causes call to __i2c_dw_enable() to immediately start the transfer which leads to timeout. There are 3 failure modes observed: 1. Failure in S0 to S3 resume path The default value after reset for DW_IC_INTR_MASK is 0x8ff. When we start the first transaction after resuming from system sleep, TX_EMPTY interrupt is already unmasked because of the hardware default. 2. Failure in normal operational path This failure happens rarely and is hard to reproduce. Debug trace showed that DW_IC_INTR_MASK had value of 0x254 when failure occurred, which meant TX_EMPTY was unmasked. 3. Failure in S3 to S0 suspend path This failure also happens rarely and is hard to reproduce. Adding debug trace that read DW_IC_INTR_MASK made this failure not reproducible. But from ISR call trace we could conclude TX_EMPTY was unmasked when problem occurred. The patch masks all interrupts before the controller is enabled to resolve the faulty DW_IC_INTR_MASK conditions. Signed-off-by:
Wenkai Du <wenkai.du@intel.com> Acked-by:
Mika Westerberg <mika.westerberg@linux.intel.com> [wsa: improved the comment and removed typo in commit msg] Signed-off-by:
-
Wolfram Sang authored
commit d7653964 upstream. This hardware does not support zero length transfers. Instead, the driver does one (random) byte transfers currently with undefined results for the slaves. We now bail out. Signed-off-by:
Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by:
-
Edward Lin authored
commit b753631b upstream. With win8 capabiltiy, the machine will boot itself immediately after shutdown command has executed. Work around this issue by disabling win8 capcability. This workaround also makes wireless hotkey work. Signed-off-by:
Edward Lin <yidi.lin@canonical.com> Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Igor Mammedov authored
commit 0b9d46dd upstream. acpi_processor_add() assumes that present at boot CPUs are always onlined, it is not so if a CPU failed to become onlined. As result acpi_processor_add() will mark such CPU device as onlined in sysfs and following attempts to online/offline it using /sys/device/system/cpu/cpuX/online attribute will fail. Do not poke into device internals in acpi_processor_add() and touch "struct device { .offline }" attribute, since for CPUs onlined at boot it's set by: topology_init() -> arch_register_cpu() -> register_cpu() before ACPI device tree is parsed, and for hotplugged CPUs it's set when userspace onlines CPU via sysfs. Signed-off-by:
Igor Mammedov <imammedo@redhat.com> Acked-by:
Toshi Kani <toshi.kani@hp.com> Signed-off-by:
-
Hans de Goede authored
commit f6e6e1b9 upstream. Without this this EEE PC exports a non working WMI interface, with this it exports a working "good old" eeepc_laptop interface, fixing brightness control not working as well as rfkill being stuck in a permanent wireless blocked state. This is not an ideal way to fix this, but various attempts to fix this otherwise have failed, see: References: https://bugzilla.redhat.com/show_bug.cgi?id=1067181 Reported-and-tested-by: lou.cardone@gmail.com Signed-off-by:
Hans de Goede <hdegoede@redhat.com> Signed-off-by:
-
Levente Kurusa authored
commit a6f9bf4d upstream. When a ZPODD device is unbound via sysfs, the ACPI notify handler is not removed. This causes panics as observed in Bug #74601. The panic only happens when the wake happens from outside the kernel (i.e. inserting a media or pressing a button). Add a loop to ata_port_detach which loops through the port's devices and checks if zpodd is enabled, if so call zpodd_exit. Reviewed-by:
Aaron Lu <aaron.lu@intel.com> Signed-off-by:
Levente Kurusa <levex@linux.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Andy Shevchenko authored
commit 97977f75 upstream. The commit dbde5c29 "dw_dmac: use devm_* functions to simplify code" turns probe function to use devm_* helpers and simultaneously brings a regression. We need to ensure irq is disabled, followed by ensuring that don't schedule any more tasklets and then its safe to use tasklet_kill(). The free_irq() will ensure that the irq is disabled and also wait till all scheduled interrupts are executed by invoking synchronize_irq(). So we need to only do tasklet_kill() after invoking free_irq(). Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by:
Vinod Koul <vinod.koul@intel.com> Signed-off-by:
-
Ezequiel Garcia authored
commit 5a9a55bf upstream. We need to use writel() instead of writel_relaxed() when starting a channel, to ensure all the descriptors have been flushed before the activation. While at it, remove the unneeded read-modify-write and make the code simpler. Signed-off-by:
Lior Amsalem <alior@marvell.com> Signed-off-by:
Ezequiel Garcia <ezequiel.garcia@free-electrons.com> Signed-off-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
-
Mikulas Patocka authored
commit 610f2de3 upstream. The DM crypt target used per-cpu structures to hold pointers to a ablkcipher_request structure. The code assumed that the work item keeps executing on a single CPU, so it didn't use synchronization when accessing this structure. If a CPU is disabled by writing 0 to /sys/devices/system/cpu/cpu*/online, the work item could be moved to another CPU. This causes dm-crypt crashes, like the following, because the code starts using an incorrect ablkcipher_request: smpboot: CPU 7 is now offline BUG: unable to handle kernel NULL pointer dereference at 0000000000000130 IP: [<ffffffffa1862b3d>] crypt_convert+0x12d/0x3c0 [dm_crypt] ... Call Trace: [<ffffffffa1864415>] ? kcryptd_crypt+0x305/0x470 [dm_crypt] [<ffffffff81062060>] ? finish_task_switch+0x40/0xc0 [<ffffffff81052a28>] ? process_one_work+0x168/0x470 [<ffffffff8105366b>] ? worker_thread+0x10b/0x390 [<ffffffff81053560>] ? manage_workers.isra.26+0x290/0x290 [<ffffffff81058d9f>] ? kthread+0xaf/0xc0 [<ffffffff81058cf0>] ? kthread_create_on_node+0x120/0x120 [<ffffffff813464ac>] ? ret_from_fork+0x7c/0xb0 [<ffffffff81058cf0>] ? kthread_create_on_node+0x120/0x120 Fix this bug by removing the per-cpu definition. The structure ablkcipher_request is accessed via a pointer from convert_context. Consequently, if the work item is rescheduled to a different CPU, the thread still uses the same ablkcipher_request. This change may undermine performance improvements intended by commit c0297721 ("dm crypt: scale to multiple cpus") on select hardware. In practice no performance difference was observed on recent hardware. But regardless, correctness is more important than performance. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@redhat.com> Signed-off-by:
-
Jani Nikula authored
This is commit 0f540c3a upstream. Since commit ee1452d7 Author: Jani Nikula <jani.nikula@intel.com> Date: Fri Sep 20 15:05:30 2013 +0300 drm/i915: assume all GM45 Acer laptops use inverted backlight PWM failed and was later reverted in commit be505f64 Author: Alexander van Heukelum <heukelum@fastmail.fm> Date: Sat Dec 28 21:00:39 2013 +0100 Revert "drm/i915: assume all GM45 Acer laptops use inverted backlight PWM" fix the individual broken machine instead. Note to backporters: http://patchwork.freedesktop.org/patch/17837/ is the patch you want for 3.13 and older. Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=54171 Reference: http://mid.gmane.org/DUB115-W7628C7C710EA51AA110CD4A5000@phx.gblSigned-off-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Ville Syrjälä <ville.syrjala@linux.intel.com> [danvet: Patch mangling for 3.14 plus adding the link to the original for 3.13.] Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch>
-
Chris Wilson authored
This is commit df6f783a upstream. On non-LLC platforms, when changing the cache level of an object, we may need to unbind it so that prefetching across page boundaries does not cross into a different memory domain. This requires us to unbind conflicting vma, but we did so iterating over the objects vma in an unsafe manner (as the list was being modified as we iterated). The regression was introduced in commit 3089c6f2 Author: Ben Widawsky <ben@bwidawsk.net> Date: Wed Jul 31 17:00:03 2013 -0700 drm/i915: make caching operate on all address spaces apparently as far back as v3.12-rc1, but it has only just begun to trigger real world bug reports. Reported-and-tested-by:
Nikolay Martynov <mar.kolya@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76384Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Cc: Ben Widawsky <ben@bwidawsk.net> Signed-off-by:
-
Daniel Vetter authored
This is commit 2ab1bc9d upstream. Apparently it doesn't work. X-tiled self-refresh works flawlessly otoh. Apparently X still works correctly with linear framebuffers, so might just be an issue with the initial modeset. It's unclear whether this just borked wm setup from our side or a hw restriction, but just disabling gets things going. Note that this regression was only brought to light with commit 3f2dc5ac Author: Ville Syrjälä <ville.syrjala@linux.intel.com> Date: Fri Jan 10 14:06:47 2014 +0200 drm/i915: Fix 915GM self-refresh enable/disable before that self-refresh for i915GM didn't work at all. Kudos to Ville for spotting a little bug in the original patch I've attached to the bug. Cc: Ville Syrjälä <ville.syrjala@linux.intel.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76103Tested-by:
Krzysztof Mazur <krzysiek@podlesie.net> Cc: Krzysztof Mazur <krzysiek@podlesie.net> Reviewed-by:
-
Mikulas Patocka authored
commit 1e1110c4 upstream. On each processed XCOPY command, two "kmalloc-512" memory objects are leaked. These represent two allocations of struct xcopy_pt_cmd in target_core_xcopy.c. The reason for the memory leak is that the cmd_kref field is not initialized (thus, it is zero because the allocations were done with kzalloc). When we decrement zero kref in target_put_sess_cmd, the result is not zero, thus target_release_cmd_kref is not called. This patch fixes the bug by moving kref initialization from target_get_sess_cmd to transport_init_se_cmd (this function is called from target_core_xcopy.c, so it will correctly initialize cmd_kref). It can be easily verified that all code that calls target_get_sess_cmd also calls transport_init_se_cmd earlier, thus moving kref_init shouldn't introduce any new problems. Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> Signed-off-by:
-
Andy Grover authored
commit 07b8dae3 upstream. Just like for pSCSI, if the transport sets get_write_cache, then it is not valid to enable write cache emulation for it. Return an error. see https://bugzilla.redhat.com/show_bug.cgi?id=1082675Reviewed-by:
Chris Leech <cleech@redhat.com> Signed-off-by:
Andy Grover <agrover@redhat.com> Signed-off-by:
-
Nicholas Bellinger authored
commit 7cbfcc95 upstream. This patch changes an incorrect use of BUG_ON to instead generate a REJECT + PROTOCOL_ERROR in iscsit_process_nop_out() code. This case can occur with traditional TCP where a flood of zeros in the data stream can reach this block for what is presumed to be a NOP-OUT with a solicited reply, but without a valid iscsi_cmd pointer. This incorrect BUG_ON was introduced during the v3.11-rc timeframe with the following commit: commit 778de368 Author: Nicholas Bellinger <nab@linux-iscsi.org> Date: Fri Jun 14 16:07:47 2013 -0700 iscsi/isert-target: Refactor ISCSI_OP_NOOP RX handling Reported-by:
Arshad Hussain <arshad.hussain@calsoftinc.com> Signed-off-by:
-
Sagi Grimberg authored
commit 531b7bf4 upstream. RDMA CM and iSCSI target flows are asynchronous and completely uncorrelated. Relying on the fact that iscsi_accept_np will be called after CM connection request event and will wait for it is a mistake. When attempting to login to a few targets this flow is racy and unpredictable, but for parallel login to dozens of targets will race and hang every time. The correct synchronizing mechanism in this case is pending on a semaphore rather than a wait_for_event. We keep the pending interruptible for iscsi_np cleanup stage. (Squash patch to remove dead code into parent - nab) Reported-by:
Slava Shwartsman <valyushash@gmail.com> Signed-off-by:
Sagi Grimberg <sagig@mellanox.com> Signed-off-by:
-
Sagi Grimberg authored
commit 9fe63c88 upstream. Should be adding list_add_tail($new, $head) and not the other way around. Signed-off-by:
-
Marcel Apfelbaum authored
commit 93fa9d32 upstream. When a new device is added below a hotplug bridge, the bridge's secondary bus speed and the device's bus speed must match. The shpchp driver previously checked the bridge's *primary* bus speed, not the secondary bus speed. This caused hot-add errors like: shpchp 0000:00:03.0: Speed of bus ff and adapter 0 mismatch Check the secondary bus speed instead. [bhelgaas: changelog] Link: https://bugzilla.kernel.org/show_bug.cgi?id=75251 Fixes: 3749c51a ("PCI: Make current and maximum bus speeds part of the PCI core") Signed-off-by:
Marcel Apfelbaum <marcel.a@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Arnd Bergmann authored
commit 4c88d7f9 upstream. Patch 01f8fa4f "genirq: Allow forcing cpu affinity of interrupts" added an irq_force_affinity() function, and 30ccf03b "clocksource: Exynos_mct: Use irq_force_affinity() in cpu bringup" subsequently uses it. However, the driver can be used with CONFIG_SMP disabled, but the function declaration is only available for CONFIG_SMP, leading to this build error: drivers/clocksource/exynos_mct.c:431:3: error: implicit declaration of function 'irq_force_affinity' [-Werror=implicit-function-declaration] irq_force_affinity(mct_irqs[MCT_L0_IRQ + cpu], cpumask_of(cpu)); This patch introduces a dummy helper function for the non-SMP case that always returns success, to get rid of the build error. Since the patches causing the problem are marked for stable backports, this one should be as well. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Cc: Krzysztof Kozlowski <k.kozlowski@samsung.com> Acked-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Linus Torvalds authored
commit fa81511b upstream. Checkin: b3b42ac2 x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels disabled 16-bit segments on 64-bit kernels due to an information leak. However, it does seem that people are genuinely using Wine to run old 16-bit Windows programs on Linux. A proper fix for this ("espfix64") is coming in the upcoming merge window, but as a temporary fix, create a sysctl to allow the administrator to re-enable support for 16-bit segments. It adds a "/proc/sys/abi/ldt16" sysctl that defaults to zero (off). If you hit this issue and care about your old Windows program more than you care about a kernel stack address information leak, you can do echo 1 > /proc/sys/abi/ldt16 as root (add it to your startup scripts), and you should be ok. The sysctl table is only added if you have COMPAT support enabled on x86-64, but I assume anybody who runs old windows binaries very much does that ;) Signed-off-by:
H. Peter Anvin <hpa@linux.intel.com> Link: http://lkml.kernel.org/r/CA%2B55aFw9BPoD10U1LfHbOMpHWZkvJTkMcfCs9s3urPr1YyWBxw@mail.gmail.comSigned-off-by:
-
James Hogan authored
commit d71f290b upstream. Specify the maximum stack size for arches where the stack grows upward (parisc and metag) in asm/processor.h rather than hard coding in fs/exec.c so that metag can specify a smaller value of 256MB rather than 1GB. This fixes a BUG on metag if the RLIMIT_STACK hard limit is increased beyond a safe value by root. E.g. when starting a process after running "ulimit -H -s unlimited" it will then attempt to use a stack size of the maximum 1GB which is far too big for metag's limited user virtual address space (stack_top is usually 0x3ffff000): BUG: failure at fs/exec.c:589/shift_arg_pages()! Signed-off-by:
James Hogan <james.hogan@imgtec.com> Cc: Helge Deller <deller@gmx.de> Cc: "James E.J. Bottomley" <jejb@parisc-linux.org> Cc: linux-parisc@vger.kernel.org Cc: linux-metag@vger.kernel.org Cc: John David Anglin <dave.anglin@bell.net> Signed-off-by:
-
Mikulas Patocka authored
commit 2425ce84 upstream. Volatile access doesn't really imply the compiler barrier. Volatile access is only ordered with respect to other volatile accesses, it isn't ordered with respect to general memory accesses. Gcc may reorder memory accesses around volatile access, as we can see in this simple example (if we compile it with optimization, both increments of *b will be collapsed to just one): void fn(volatile int *a, long *b) { (*b)++; *a = 10; (*b)++; } Consequently, we need the compiler barrier after a write to the volatile variable, to make sure that the compiler doesn't reorder the volatile write with something else. Signed-off-by:
Peter Zijlstra <peterz@infradead.org> Signed-off-by:
-
Charles Keepax authored
commit 44330ab5 upstream. The register CLASS_D_CONTROL_1 is marked as volatile because it contains a bit, DAC_MUTE, which is also mirrored in the ADC_DAC_CONTROL_1 register. This causes problems for the "Speaker Switch" control, which will report an error if the CODEC is suspended because it relies on a volatile register. To resolve this issue mark CLASS_D_CONTROL_1 as non-volatile and manually keep the register cache in sync by updating both bits when changing the mute status. Reported-by:
Shawn Guo <shawn.guo@linaro.org> Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Tested-by:
Mark Brown <broonie@linaro.org> Signed-off-by:
-
Jianyu Zhan authored
commit 5a838c3b upstream. pcpu_chunk_struct_size = sizeof(struct pcpu_chunk) + BITS_TO_LONGS(pcpu_unit_pages) * sizeof(unsigned long) It hardly could be ever bigger than PAGE_SIZE even for large-scale machine, but for consistency with its couterpart pcpu_mem_zalloc(), use pcpu_mem_free() instead. Commit b4916cb1 ("percpu: make pcpu_free_chunk() use pcpu_mem_free() instead of kfree()") addressed this problem, but missed this one. tj: commit message updated Signed-off-by:
Jianyu Zhan <nasa4836@gmail.com> Signed-off-by:
-
Thomas Petazzoni authored
commit b566e782 upstream. Having multiple windows with the same target and attribute is actually legal, and can be useful for PCIe windows, when PCIe BARs have a size that isn't a power of two, and we therefore need to create several MBus windows to cover the PCIe BAR for a given PCIe interface. Fixes: fddddb52 ('bus: introduce an Marvell EBU MBus driver') Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Link: https://lkml.kernel.org/r/1397823593-1932-7-git-send-email-thomas.petazzoni@free-electrons.comTested-by:
Neil Greatorex <neil@fatboyfat.co.uk> Signed-off-by:
Jason Cooper <jason@lakedaemon.net> Signed-off-by:
-
Willy Tarreau authored
commit b6d07e02 upstream. mvebu_pcie_handle_membase_change() and mvebu_pcie_handle_iobase_change() do not correctly compute the window size. PCI uses an inclusive start/end address pair, which requires a +1 when converting to size. This only worked because a bug in the mbus driver allowed it to silently accept and round up bogus sizes. Fix this by adding one to the computed size. Fixes: 45361a4f ('PCIe driver for Marvell Armada 370/XP systems') Signed-off-by:
Willy Tarreau <w@1wt.eu> Reviewed-By:
Jason Gunthorpe <jgunthorpe@obsidianresearch.com> Signed-off-by:
-
Thomas Petazzoni authored
commit ce965c3d upstream. According to the Armada 370 and Armada XP datasheets, the part of the Device Bus register that configure the bus width should contain 0 for a 8 bits bus width, and 1 for a 16 bits bus width (other values are unsupported/reserved). However, the current conversion done in the driver to convert from a bus width in bits to the value expected by the register leads to setting the register to 1 for a 8 bits bus, and 2 for a 16 bits bus. This mistake was compensated by a mistake in the existing Device Tree files for Armada 370/XP platforms: they were declaring a 8 bits bus width, while the hardware in fact uses a 16 bits bus width. This commit fixes that by adjusting the conversion logic. This patch fixes a bug that was introduced in 3edad321 ('drivers: memory: Introduce Marvell EBU Device Bus driver'), which was merged in v3.11. Signed-off-by:
Gregory CLEMENT <gregory.clement@free-electrons.com> Signed-off-by:
-
Lai Jiangshan authored
commit 4d595b86 upstream. After a @pwq is scheduled for emergency execution, other workers may consume the affectd work items before the rescuer gets to them. This means that a workqueue many have pwqs queued on @wq->maydays list while not having any work item pending or in-flight. If destroy_workqueue() executes in such condition, the rescuer may exit without emptying @wq->maydays. This currently doesn't cause any actual harm. destroy_workqueue() can safely destroy all the involved data structures whether @wq->maydays is populated or not as nobody access the list once the rescuer exits. However, this is nasty and makes future development difficult. Let's update rescuer_thread() so that it empties @wq->maydays after seeing should_stop to guarantee that the list is empty on rescuer exit. tj: Updated comment and patch description. Signed-off-by:
Lai Jiangshan <laijs@cn.fujitsu.com> Signed-off-by:
-
Lai Jiangshan authored
commit 77668c8b upstream. There is a race condition between rescuer_thread() and pwq_unbound_release_workfn(). Even after a pwq is scheduled for rescue, the associated work items may be consumed by any worker. If all of them are consumed before the rescuer gets to them and the pwq's base ref was put due to attribute change, the pwq may be released while still being linked on @wq->maydays list making the rescuer dereference already freed pwq later. Make send_mayday() pin the target pwq until the rescuer is done with it. tj: Updated comment and patch description. Signed-off-by:
-
Daeseok Youn authored
commit 77f300b1 upstream. wq_update_unbound_numa() failure path has the following two bugs. - alloc_unbound_pwq() is called without holding wq->mutex; however, if the allocation fails, it jumps to out_unlock which tries to unlock wq->mutex. - The function should switch to dfl_pwq on failure but didn't do so after alloc_unbound_pwq() failure. Fix it by regrabbing wq->mutex and jumping to use_dfl_pwq on alloc_unbound_pwq() failure. Signed-off-by:
Daeseok Youn <daeseok.youn@gmail.com> Acked-by:
-
J. Bruce Fields authored
commit a1b8ff4c upstream. The nfsv4 state code has always assumed a one-to-one correspondance between lock stateid's and lockowners even if it appears not to in some places. We may actually change that, but for now when FREE_STATEID releases a lock stateid it also needs to release the parent lockowner. Symptoms were a subsequent LOCK crashing in find_lockowner_str when it calls same_lockowner_ino on a lockowner that unexpectedly has an empty so_stateids list. Signed-off-by:
J. Bruce Fields <bfields@redhat.com> Signed-off-by:
-
J. Bruce Fields authored
commit 27b11428 upstream. The current code assumes a one-to-one lockowner<->lock stateid correspondance. Signed-off-by:
-
Kinglong Mee authored
commit aa07c713 upstream. After setting ACL for directory, I got two problems that caused by the cached zero-length default posix acl. This patch make sure nfsd4_set_nfs4_acl calls ->set_acl with a NULL ACL structure if there are no entries. Thanks for Christoph Hellwig's advice. First problem: ............ hang ........... Second problem: [ 1610.167668] ------------[ cut here ]------------ [ 1610.168320] kernel BUG at /root/nfs/linux/fs/nfsd/nfs4acl.c:239! [ 1610.168320] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC [ 1610.168320] Modules linked in: nfsv4(OE) nfs(OE) nfsd(OE) rpcsec_gss_krb5 fscache ip6t_rpfilter ip6t_REJECT cfg80211 xt_conntrack rfkill ebtable_nat ebtable_broute bridge stp llc ebtable_filter ebtables ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw ip6table_filter ip6_tables iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat nf_conntrack iptable_mangle iptable_security iptable_raw auth_rpcgss nfs_acl snd_intel8x0 ppdev lockd snd_ac97_codec ac97_bus snd_pcm snd_timer e1000 pcspkr parport_pc snd parport serio_raw joydev i2c_piix4 sunrpc(OE) microcode soundcore i2c_core ata_generic pata_acpi [last unloaded: nfsd] [ 1610.168320] CPU: 0 PID: 27397 Comm: nfsd Tainted: G OE 3.15.0-rc1+ #15 [ 1610.168320] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 1610.168320] task: ffff88005ab653d0 ti: ffff88005a944000 task.ti: ffff88005a944000 [ 1610.168320] RIP: 0010:[<ffffffffa034d5ed>] [<ffffffffa034d5ed>] _posix_to_nfsv4_one+0x3cd/0x3d0 [nfsd] [ 1610.168320] RSP: 0018:ffff88005a945b00 EFLAGS: 00010293 [ 1610.168320] RAX: 0000000000000001 RBX: ffff88006700bac0 RCX: 0000000000000000 [ 1610.168320] RDX: 0000000000000000 RSI: ffff880067c83f00 RDI: ffff880068233300 [ 1610.168320] RBP: ffff88005a945b48 R08: ffffffff81c64830 R09: 0000000000000000 [ 1610.168320] R10: ffff88004ea85be0 R11: 000000000000f475 R12: ffff880068233300 [ 1610.168320] R13: 0000000000000003 R14: 0000000000000002 R15: ffff880068233300 [ 1610.168320] FS: 0000000000000000(0000) GS:ffff880077800000(0000) knlGS:0000000000000000 [ 1610.168320] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 1610.168320] CR2: 00007f5bcbd3b0b9 CR3: 0000000001c0f000 CR4: 00000000000006f0 [ 1610.168320] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 1610.168320] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 [ 1610.168320] Stack: [ 1610.168320] ffffffff00000000 0000000b67c83500 000000076700bac0 0000000000000000 [ 1610.168320] ffff88006700bac0 ffff880068233300 ffff88005a945c08 0000000000000002 [ 1610.168320] 0000000000000000 ffff88005a945b88 ffffffffa034e2d5 000000065a945b68 [ 1610.168320] Call Trace: [ 1610.168320] [<ffffffffa034e2d5>] nfsd4_get_nfs4_acl+0x95/0x150 [nfsd] [ 1610.168320] [<ffffffffa03400d6>] nfsd4_encode_fattr+0x646/0x1e70 [nfsd] [ 1610.168320] [<ffffffff816a6e6e>] ? kmemleak_alloc+0x4e/0xb0 [ 1610.168320] [<ffffffffa0327962>] ? nfsd_setuser_and_check_port+0x52/0x80 [nfsd] [ 1610.168320] [<ffffffff812cd4bb>] ? selinux_cred_prepare+0x1b/0x30 [ 1610.168320] [<ffffffffa0341caa>] nfsd4_encode_getattr+0x5a/0x60 [nfsd] [ 1610.168320] [<ffffffffa0341e07>] nfsd4_encode_operation+0x67/0x110 [nfsd] [ 1610.168320] [<ffffffffa033844d>] nfsd4_proc_compound+0x21d/0x810 [nfsd] [ 1610.168320] [<ffffffffa0324d9b>] nfsd_dispatch+0xbb/0x200 [nfsd] [ 1610.168320] [<ffffffffa00850cd>] svc_process_common+0x46d/0x6d0 [sunrpc] [ 1610.168320] [<ffffffffa0085433>] svc_process+0x103/0x170 [sunrpc] [ 1610.168320] [<ffffffffa032472f>] nfsd+0xbf/0x130 [nfsd] [ 1610.168320] [<ffffffffa0324670>] ? nfsd_destroy+0x80/0x80 [nfsd] [ 1610.168320] [<ffffffff810a5202>] kthread+0xd2/0xf0 [ 1610.168320] [<ffffffff810a5130>] ? insert_kthread_work+0x40/0x40 [ 1610.168320] [<ffffffff816c1ebc>] ret_from_fork+0x7c/0xb0 [ 1610.168320] [<ffffffff810a5130>] ? insert_kthread_work+0x40/0x40 [ 1610.168320] Code: 78 02 e9 e7 fc ff ff 31 c0 31 d2 31 c9 66 89 45 ce 41 8b 04 24 66 89 55 d0 66 89 4d d2 48 8d 04 80 49 8d 5c 84 04 e9 37 fd ff ff <0f> 0b 90 0f 1f 44 00 00 55 8b 56 08 c7 07 00 00 00 00 8b 46 0c [ 1610.168320] RIP [<ffffffffa034d5ed>] _posix_to_nfsv4_one+0x3cd/0x3d0 [nfsd] [ 1610.168320] RSP <ffff88005a945b00> [ 1610.257313] ---[ end trace 838254e3e352285b ]--- Signed-off-by:
Kinglong Mee <kinglongmee@gmail.com> Signed-off-by:
-
Trond Myklebust authored
commit 4cb57e30 upstream. Mainly to ensure that we don't leave any hanging timers. Signed-off-by:
Trond Myklebust <trond.myklebust@primarydata.com> Signed-off-by:
-
Trond Myklebust authored
commit 5694c93e upstream. Aside from making it clearer what is non-trivial in create_client(), it also fixes a bug whereby we can call free_client() before idr_init() has been called. Signed-off-by:
-
