The `connected` value for wired devices was not properly initialized,
it must be set to `true` upon creation, because wired devices do not
generate connection events.

When a raw client (the Steam Client) uses the device, the input device
is destroyed. Then, when the raw client finishes, it must be recreated.
But since the `connected` variable was false this never happended.
Signed-off-by: Rodrigo Rivas Costa <rodrigorivascosta@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Added Tiger Lake PCI device ID to the supported device list.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

1002     if ((quirks & MT_QUIRK_IGNORE_DUPLICATES) && mt) {
1003         struct input_mt_slot *i_slot = &mt->slots[slotnum];
1004
1005         if (input_mt_is_active(i_slot) &&
1006             input_mt_is_used(mt, i_slot))
1007             return -EAGAIN;
1008     }

We previously assumed 'mt' could be null (see line 1002).

The following situation is similar, so add a judgement.
Signed-off-by: Pan Zhang <zhangpan26@huawei.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>

A new PID is in use for repaired MobileStudio Pro devices. Add it to the
list of devices that need special-casing in wacom_wac_pad_event.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>

Add Comet Lake H into ishtp support list.
Signed-off-by: Even Xu <even.xu@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>

The open method of hiddev handler fails to bring the device out of
autosuspend state as was promised in 0361a28d, as it actually has 2
blocks that try to start the transport (call hid_hw_open()) with both
being guarded by the "open" counter, so the 2nd block is never executed as
the first block increments the counter so it is never at 0 when we check
it for the second block.

Additionally hiddev_open() was leaving counter incremented on errors,
causing the device to never be reopened properly if there was ever an
error.

Let's fix all of this by factoring out code that creates client structure
and powers up the device into a separate function that is being called
from usbhid_open() with the "existancelock" being held.

Fixes: 0361a28d ("HID: autosuspend support for USB HID")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>

We should not be leaving half-mapped usages with potentially invalid
keycodes, as that may confuse hidinput_find_key() when the key is located
by index, which may end up feeding way too large keycode into the VT
keyboard handler and cause OOB write there:

BUG: KASAN: global-out-of-bounds in clear_bit include/asm-generic/bitops-instrumented.h:56 [inline]
BUG: KASAN: global-out-of-bounds in kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
BUG: KASAN: global-out-of-bounds in kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
Write of size 8 at addr ffffffff89a1b2d8 by task syz-executor108/1722
...
 kbd_keycode drivers/tty/vt/keyboard.c:1411 [inline]
 kbd_event+0xe6b/0x3790 drivers/tty/vt/keyboard.c:1495
 input_to_handler+0x3b6/0x4c0 drivers/input/input.c:118
 input_pass_values.part.0+0x2e3/0x720 drivers/input/input.c:145
 input_pass_values drivers/input/input.c:949 [inline]
 input_set_keycode+0x290/0x320 drivers/input/input.c:954
 evdev_handle_set_keycode_v2+0xc4/0x120 drivers/input/evdev.c:882
 evdev_do_ioctl drivers/input/evdev.c:1150 [inline]

Cc: stable@vger.kernel.org
Reported-by: syzbot+19340dff067c2d3835c0@syzkaller.appspotmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Tested-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Apply it to the Lenovo Y720 gaming laptop I2C peripheral then.

This fixes dmesg being flooded with errors visible on un-suspend
in Linux Mint 19 Cinnamon.

Example of error log:

<...>
[    4.326588] i2c_hid i2c-ITE33D1:00: i2c_hid_get_input: incomplete report (2/4)
[    4.326845] i2c_hid i2c-ITE33D1:00: i2c_hid_get_input: incomplete report (2/4)
[    4.327095] i2c_hid i2c-ITE33D1:00: i2c_hid_get_input: incomplete report (2/4)
[    4.327341] i2c_hid i2c-ITE33D1:00: i2c_hid_get_input: incomplete report (2/4)
[    4.327609] i2c_hid i2c-ITE33D1:00: i2c_hid_get_input: incomplete report (2/4)
<...>

Example of fixed log (debug on)

<...>
[ 3731.333183] i2c_hid i2c-ITE33D1:00: input: 02 00
[ 3731.333581] i2c_hid i2c-ITE33D1:00: input: 02 00
[ 3731.333842] i2c_hid i2c-ITE33D1:00: input: 02 00
[ 3731.334107] i2c_hid i2c-ITE33D1:00: input: 02 00
[ 3731.334367] i2c_hid i2c-ITE33D1:00: input: 02 00
<...>

[jkosina@suse.cz: rebase onto more recent codebase]
Signed-off-by: Pavel Balan <admin@kryma.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

At least on a T100HA an Asus vendor-page usage-code 0xff event is send on
every suspend and again on resume, resulting in the following warning:

asus 0003:0B05:1807.0002: Unmapped Asus vendor usagepage code 0xff

being logged twice on every suspend/resume.

This commit silences the "Unmapped Asus vendor usagepage code ..."
warning for usage-code 0xff to avoid these warnings being logged.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The Acer SW5-012 2-in-1 keyboard dock uses a Synaptics S91028 touchpad
which is connected to an ITE 8595 USB keyboard controller chip.

This keyboard has the same quirk for its rfkill / airplane mode hotkey as
other keyboards with the ITE 8595 chip, it only sends a single release
event when pressed and released, it never sends a press event.

This commit adds this keyboards USB id to the hid-ite id-table, fixing
the rfkill key not working on this keyboard.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Without the quirk, joystick shows up as single controller
for both first and second player pads/pins.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

The syzbot fuzzer found a slab-out-of-bounds bug in the HID report
handler.  The bug was caused by a report descriptor which included a
field with size 12 bits and count 4899, for a total size of 7349
bytes.

The usbhid driver uses at most a single-page 4-KB buffer for reports.
In the test there wasn't any problem about overflowing the buffer,
since only one byte was received from the device.  Rather, the bug
occurred when the HID core tried to extract the data from the report
fields, which caused it to try reading data beyond the end of the
allocated buffer.

This patch fixes the problem by rejecting any report whose total
length exceeds the HID_MAX_BUFFER_SIZE limit (minus one byte to allow
for a possible report index).  In theory a device could have a report
longer than that, but if there was such a thing we wouldn't handle it
correctly anyway.

Reported-and-tested-by: syzbot+09ef48aa58261464b621@syzkaller.appspotmail.com
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Add multitouch support for LG MELF I2C touchscreen.
Apply the same workaround as LG USB touchscreen.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Always return EPOLLOUT from uhid_char_poll to allow polling /dev/uhid
for writable state.

Fixes: 1f9dec1e ("HID: uhid: allow poll()'ing on uhid devices")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

When polling a connected /dev/hidrawX device, it is useful to get the
EPOLLOUT when writing is possible. Since writing is possible as soon as
the device is connected, always return it.

Right now EPOLLOUT is only returned when there are also input reports
are available. This works if devices start sending reports when
connected, but some HID devices might need an output report first before
sending any input reports. This change will allow using EPOLLOUT here as
well.

Fixes: 378b8037 ("hidraw: Return EPOLLOUT from hidraw_poll")
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Cc: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Pull HID updates from Jiri Kosina:

 - Support for Logitech G15 (Hans de Goede)

 - HID parser improvements, improving support for some devices; e.g.
   Windows Precision Touchpad, products from Primax, etc. (Blaž
   Hrastnik, Candle Sun)

 - robustification of tablet mode support in google-whiskers driver
   (Dmitry Torokhov)

 - assorted small fixes, device-specific quirks and device ID additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hid/hid: (23 commits)
  HID: rmi: Check that the RMI_STARTED bit is set before unregistering the RMI transport device
  HID: quirks: remove hid-led devices from hid_have_special_driver
  HID: Improve Windows Precision Touchpad detection.
  HID: i2c-hid: Reset ALPS touchpads on resume
  HID: i2c-hid: fix no irq after reset on raydium 3118
  HID: logitech-hidpp: Silence intermittent get_battery_capacity errors
  HID: i2c-hid: remove orphaned member sleep_delay
  HID: quirks: Add quirk for HP MSU1465 PIXART OEM mouse
  HID: core: check whether Usage Page item is after Usage ID items
  HID: intel-ish-hid: Spelling s/diconnect/disconnect/
  HID: google: Detect base folded usage instead of hard-coding whiskers
  HID: logitech: Add depends on LEDS_CLASS to Logitech Kconfig entry
  HID: lg-g15: Add support for the G510's M1-M3 and MR LEDs
  HID: lg-g15: Add support for controlling the G510's RGB backlight
  HID: lg-g15: Add support for the G510 keyboards' gaming keys
  HID: lg-g15: Add support for the M1-M3 and MR LEDs
  HID: lg-g15: Add keyboard and LCD backlight control
  HID: Add driver for Logitech gaming keyboards (G15, G15 v2)
  Input: Add event-codes for macro keys found on various keyboards
  HID: hidraw: replace printk() with corresponding pr_xx() variant
  ...

Pull watchdog updates from Wim Van Sebroeck:

 - support for NCT6116D

 - several small fixes and improvements

* tag 'linux-watchdog-5.5-rc1' of git://www.linux-watchdog.org/linux-watchdog: (24 commits)
  watchdog: jz4740: Drop dependency on MACH_JZ47xx
  watchdog: jz4740: Use regmap provided by TCU driver
  watchdog: jz4740: Use WDT clock provided by TCU driver
  dt-bindings: watchdog: sama5d4_wdt: add microchip,sam9x60-wdt compatible
  watchdog: sama5d4_wdt: cleanup the bit definitions
  watchdog: sprd: Fix the incorrect pointer getting from driver data
  watchdog: aspeed: Fix clock behaviour for ast2600
  watchdog: imx7ulp: Fix reboot hang
  watchdog: make nowayout sysfs file writable
  watchdog: prevent deferral of watchdogd wakeup on RT
  watchdog: imx7ulp: Use definitions instead of magic values
  watchdog: imx7ulp: Remove inline annotations
  watchdog: imx7ulp: Remove unused structure member
  watchdog: imx7ulp: Pass the wdog instance inimx7ulp_wdt_enable()
  watchdog: wdat_wdt: Spelling s/configrable/configurable/
  watchdog: bd70528: Trivial function documentation fix
  watchdog: cadence: Do not show error in case of deferred probe
  watchdog: Fix the race between the release of watchdog_core_data and cdev
  watchdog: sbc7240_wdt: Fix yet another -Wimplicit-fallthrough warning
  watchdog: intel-mid_wdt: Add WATCHDOG_NOWAYOUT support
  ...

Pull GPIO updates from Linus Walleij:
 "This is the bulk of GPIO changes for the v5.5 kernel cycle

  Core changes:

   - Expose pull up/down flags for the GPIO character device to
     userspace.

     After clear input from the RaspberryPi and Beagle communities, it
     has been established that prototyping, industrial automation and
     make communities strongly need this feature, and as we want people
     to use the character device, we have implemented the simple pull
     up/down interface for GPIO lines.

     This means we can specify that a (chip-specific) pull up/down
     resistor can be enabled, but does not offer fine-grained control
     such as cases where the resistance of the same pull resistor can be
     controlled (yet).

   - Introduce devm_fwnode_gpiod_get_index() and start to phase out the
     old symbol devm_fwnode_get_index_gpiod_from_child().

   - A bit of documentation clean-up work.

   - Introduce a define for GPIO line directions and deploy it in all
     GPIO drivers in the drivers/gpio directory.

   - Add a special callback to populate pin ranges when cooperating with
     the pin control subsystem and registering ranges as part of adding
     a gpiolib driver and a gpio_irq_chip driver at the same time. This
     is also deployed in the Intel Merrifield driver.

  New drivers:

   - RDA Micro GPIO controller.

   - XGS-iproc GPIO driver.

  Driver improvements:

   - Wake event and debounce support on the Tegra 186 driver.

   - Finalize the Aspeed SGPIO driver.

   - MPC8xxx uses a normal IRQ handler rather than a chained handler"

* tag 'gpio-v5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (64 commits)
  gpio: Add TODO item for regmap helper
  Documentation: gpio: driver.rst: Fix warnings
  gpio: of: Fix bogus reference to gpiod_get_count()
  gpiolib: Grammar s/manager/managed/
  gpio: lynxpoint: Setup correct IRQ handlers
  MAINTAINERS: Replace my email by one @kernel.org
  gpiolib: acpi: Make acpi_gpiochip_alloc_event always return AE_OK
  gpio/mpc8xxx: fix qoriq GPIO reading
  gpio: mpc8xxx: Don't overwrite default irq_set_type callback
  gpiolib: acpi: Print pin number on acpi_gpiochip_alloc_event errors
  gpiolib: fix coding style in gpiod_hog()
  drm/bridge: ti-tfp410: switch to using fwnode_gpiod_get_index()
  gpio: merrifield: Pass irqchip when adding gpiochip
  gpio: merrifield: Add GPIO <-> pin mapping ranges via callback
  gpiolib: Introduce ->add_pin_ranges() callback
  gpio: mmio: remove untrue leftover comment
  gpio: em: Use platform_get_irq() to obtain interrupts
  gpio: tegra186: Add debounce support
  gpio: tegra186: Program interrupt route mapping
  gpio: tegra186: Derive register offsets from bank/port
  ...

Pull MFD updates from Lee Jones:
 "Core Frameworks:
   - Add support for a "resource managed strongly uncachable ioremap"
     call
   - Provide a collection of MFD helper macros
   - Remove mfd_clone_cell() from MFD core
   - Add NULL de-reference protection in MFD core
   - Remove superfluous function fd_platform_add_cell() from MFD core
   - Honour Device Tree's request to disable a device

  New Drivers:
   - Add support for MediaTek MT6323 PMIC

  New Device Support:
   - Add support for Gemini Lake to Intel LPSS PCI
   - Add support for Cherry Trail Crystal Cover PMIC to Intel SoC PMIC
     CRC
   - Add support for PM{I}8950 to Qualcomm SPMI PMIC
   - Add support for U8420 to ST-Ericsson DB8500
   - Add support for Comet Lake PCH-H to Intel LPSS PCI

  New Functionality:
   - Add support for requested supply clocks; madera-core

  Fix-ups:
   - Lower interrupt priority; rk808
   - Use provided helpers (macros, group functions, defines); rk808,
     ipaq-micro, ab8500-core, db8500-prcmu, mt6397-core, cs5535-mfd
   - Only allocate IRQs on request; max77620
   - Use simplified API; arizona-core
   - Remove redundant and/or duplicated code; wm8998-tables, arizona,
     syscon
   - Device Tree binding fix-ups; madera, max77650, max77693
   - Remove mfd_cell->id abuse hack; cs5535-mfd
   - Remove only user of mfd_clone_cell(); cs5535-mfd
   - Make resources static; rohm-bd70528

  Bug Fixes:
   - Fix product ID for RK818; rk808
   - Fix Power Key; rk808
   - Fix booting on the BananaPi; mt6397-core
   - Endian fix-ups; twl.h
   - Fix static error checker warnings; ti_am335x_tscadc"

* tag 'mfd-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (47 commits)
  Revert "mfd: syscon: Set name of regmap_config"
  mfd: ti_am335x_tscadc: Fix static checker warning
  mfd: bd70528: Staticize bit value definitions
  mfd: mfd-core: Honour Device Tree's request to disable a child-device
  dt-bindings: mfd: max77693: Fix missing curly brace
  mfd: intel-lpss: Add Intel Comet Lake PCH-H PCI IDs
  mfd: db8500-prcmu: Support U8420-sysclk firmware
  dt-bindings: mfd: max77650: Convert the binding document to yaml
  mfd: mfd-core: Move pdev->mfd_cell creation back into mfd_add_device()
  mfd: mfd-core: Remove usage counting for .{en,dis}able() call-backs
  x86: olpc-xo1-sci: Remove invocation of MFD's .enable()/.disable() call-backs
  x86: olpc-xo1-pm: Remove invocation of MFD's .enable()/.disable() call-backs
  mfd: mfd-core: Remove mfd_clone_cell()
  mfd: mfd-core: Protect against NULL call-back function pointer
  mfd: cs5535-mfd: Register clients using their own dedicated MFD cell entries
  mfd: cs5535-mfd: Request shared IO regions centrally
  mfd: cs5535-mfd: Remove mfd_cell->id hack
  mfd: cs5535-mfd: Use PLATFORM_DEVID_* defines and tidy error message
  mfd: intel_soc_pmic_crc: Add "cht_crystal_cove_pmic" cell to CHT cells
  mfd: madera: Add support for requesting the supply clocks
  ...

Pull backlight updates from Lee Jones:
 "New Functionality:
   - Add support for an enable GPIO; lm3630a_bl
   - Add support for short circuit handling; qcom-wled
   - Add support for automatic string detection; qcom-wled

  Fix-ups:
   - Update Device Tree bindings; lm3630a-backlight, led-backlight,
     qcom-wled
   - Constify; ipaq_micro_bl
   - Optimise for CPU cycles; pwm_bl
   - Coding style fix-ups; pwm_bl
   - Trivial fix-ups (white space, comments, renaming); pwm_bl,
     gpio_backlight, qcom-wled
   - Kconfig dependency hacking; LCD_HP700
   - Rename, refactor and add peripherals; pm8941-wled => qcom-wled
   - Make use of GPIO look-up tables; tosa_bl, tosa_lcd
   - Remove superfluous code; gpio_backlight
   - Adapt GPIO direction handling; gpio_backlight
   - Remove legacy use of platform data; gpio_backlight

  Bug Fixes:
   - Provide modules aliases; lm3630a_bl"

* tag 'backlight-next-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight: (32 commits)
  backlight: qcom-wled: Fix spelling mistake "trigged" -> "triggered"
  backlight: gpio: Pull gpio_backlight_initial_power_state() into probe
  backlight: gpio: Use a helper variable for &pdev->dev
  backlight: gpio: Remove unused fields from platform data
  sh: ecovec24: don't set unused fields in platform data
  backlight: gpio: Simplify the platform data handling
  sh: ecovec24: add additional properties to the backlight device
  backlight: gpio: Explicitly set the direction of the GPIO
  backlight: gpio: Remove stray newline
  backlight: gpio: Remove unneeded include
  video: backlight: tosa: Use GPIO lookup table
  backlight: qcom-wled: Add auto string detection logic
  backlight: qcom-wled: Add support for short circuit handling
  backlight: qcom-wled: Add support for WLED4 peripheral
  backlight: qcom-wled: Restructure the driver for WLED3
  backlight: qcom-wled: Rename PM8941* to WLED3
  backlight: qcom-wled: Add new properties for PMI8998
  backlight: qcom-wled: Restructure the qcom-wled bindings
  backlight: qcom-wled: Rename pm8941-wled.c to qcom-wled.c
  dt-bindings: backlight: lm3630a: Fix missing include
  ...

Pull pinctrl fix from Linus Walleij:
 "A oneliner fix adding the license to the new Intel pin controller,
  avoiding a build-time warning"

* tag 'pinctrl-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
  pinctrl: Fix warning by adding missing MODULE_LICENSE

Pull LED updates from Pavel Machek:
 "This contains usual small updates to drivers, and removal of PAGE_SIZE
  limits on /sys/class/leds/<led>/trigger.

  We should not be really having that many triggers; but with cpu
  activity triggers we do, and we'll eventually need to fix it, but...
  remove the limit for now"

* tag 'leds-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (26 commits)
  leds: trigger: netdev: fix handling on interface rename
  leds: an30259a: add a check for devm_regmap_init_i2c
  leds: mlxreg: Fix possible buffer overflow
  leds: pca953x: Use of_device_get_match_data()
  leds: core: Fix leds.h structure documentation
  leds: core: Fix devm_classdev_match to reference correct structure
  leds: core: Remove extern from header
  leds: lm3601x: Convert class registration to device managed
  leds: flash: Add devm_* functions to the flash class
  leds: flash: Remove extern from the header file
  leds: flash: Convert non extended registration to inline
  leds: Kconfig: Be consistent with the usage of "LED"
  leds: remove PAGE_SIZE limit of /sys/class/leds/<led>/trigger
  leds: tlc591xx: update the maximum brightness
  leds: lm3692x: Use flags from LM3692X_BRT_CTRL
  leds: lm3692x: Use flags from LM3692X_BOOST_CTRL
  leds: lm3692x: Handle failure to probe the regulator
  leds: lm3692x: Don't overwrite return value in error path
  leds: lm3692x: Print error value on dev_err
  leds: tlc591xx: use devm_led_classdev_register_ext()
  ...

Pull clk updates from Stephen Boyd:
 "This merge window we have one small clk provider API in the core
  framework and then a bunch of driver updates and a handful of new
  drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
  high up there because of all the clk data introcued by new drivers.
  The Nvidia Tegra driver had a lot of work done this cycle too to
  support suspend/resume and memory controllers. And the OMAP clk driver
  got proper clk and reset handling in place.

  Rounding out the patches are various updates to remove unused data,
  mark things static, correct incorrect data in drivers, etc. All the
  little things that improve drivers and maintain code health. I will
  point out that there's a patch in here for the GPIO clk driver, that
  almost nobody uses, which changes behavior and causes clk_set_rate()
  to try to change the GPIO gate clk's parent. Other than that things
  are fairly well SoC specific here.

  Core:
   - Add a clk provider API to get current parent index
   - Plug a memory leak in clk_unregister() path

  New Drivers:
   - CGU in Ingenix X1000
   - Bitmain BM1880 clks
   - Qualcomm MSM8998 GPU clk controllers
   - Qualcomm SC7180 GCC and RPMH clk controllers
   - Qualcomm QCS404 Q6SSTOP clk controllers
   - Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
   - Add support for the Renesas RZ/G2N (r8a774b1) SoC
   - Add Tegra20/30 External Memory Clock (EMC) support

  Updates:
   - Make gpio gate clks propagate rate setting up to parent
   - Prepare Armada 3700 for suspend to RAM by moving PCIe
     suspend/resume priority
   - Drop unused variables, enums, etc. in various clk drivers
   - Convert various drivers to use devm_platform_ioremap_resource()
   - Use struct_size() some more in various clk drivers
   - Improve Rockchip px30 clk tree
   - Add suspend/resume support to Tegra210 clk driver
   - Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
   - Allwinner DT exports and H6 clk tree fixes
   - Proper clk and reset handling for OMAP SoCs
   - Revamped TI divider clk to clamp max divider
   - Make 1443X/1416X PLL clock structure common for reusing among i.MX8
     SoCs
   - Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
   - Add VIDEO2_PLL clock for imx8mq
   - Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
   - Add sm1 support in the Amlogic audio clock controller
   - Switch some clocks on R-Car Gen2/3 to .determine_rate()
   - Remove Renesas R-Car Gen2 legacy DT clock support
   - Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
   - Improve Renesas R-Car Gen3 SD clock handling
   - Add rate table for Samsung exynos542x GPU and VPLL clks
   - Fix potential CPU performance degradation after system
     suspend/resume cycle on exynos542x SoCs"

* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
  clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
  MAINTAINERS: Add entry for BM1880 SoC clock driver
  clk: Add common clock driver for BM1880 SoC
  dt-bindings: clock: Add devicetree binding for BM1880 SoC
  clk: Add clk_hw_unregister_composite helper function definition
  clk: Zero init clk_init_data in helpers
  clk: ingenic: Allow drivers to be built with COMPILE_TEST
  MAINTAINERS: Update section for Ux500 clock drivers
  clk: mark clk_disable_unused() as __init
  clk: Fix memory leak in clk_unregister()
  clk: Ingenic: Add CGU driver for X1000.
  dt-bindings: clock: Add X1000 bindings.
  clk: tegra: Use match_string() helper to simplify the code
  clk: pxa: fix one of the pxa RTC clocks
  clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
  clk: armada-xp: remove unused code
  clk: tegra: Fix build error without CONFIG_PM_SLEEP
  clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
  clk: tegra: Optimize PLLX restore on Tegra20/30
  clk: tegra: Add suspend and resume support on Tegra210
  ...

Pull y2038 cleanups from Arnd Bergmann:
 "y2038 syscall implementation cleanups

  This is a series of cleanups for the y2038 work, mostly intended for
  namespace cleaning: the kernel defines the traditional time_t, timeval
  and timespec types that often lead to y2038-unsafe code. Even though
  the unsafe usage is mostly gone from the kernel, having the types and
  associated functions around means that we can still grow new users,
  and that we may be missing conversions to safe types that actually
  matter.

  There are still a number of driver specific patches needed to get the
  last users of these types removed, those have been submitted to the
  respective maintainers"

Link: https://lore.kernel.org/lkml/20191108210236.1296047-1-arnd@arndb.de/

* tag 'y2038-cleanups-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (26 commits)
  y2038: alarm: fix half-second cut-off
  y2038: ipc: fix x32 ABI breakage
  y2038: fix typo in powerpc vdso "LOPART"
  y2038: allow disabling time32 system calls
  y2038: itimer: change implementation to timespec64
  y2038: move itimer reset into itimer.c
  y2038: use compat_{get,set}_itimer on alpha
  y2038: itimer: compat handling to itimer.c
  y2038: time: avoid timespec usage in settimeofday()
  y2038: timerfd: Use timespec64 internally
  y2038: elfcore: Use __kernel_old_timeval for process times
  y2038: make ns_to_compat_timeval use __kernel_old_timeval
  y2038: socket: use __kernel_old_timespec instead of timespec
  y2038: socket: remove timespec reference in timestamping
  y2038: syscalls: change remaining timeval to __kernel_old_timeval
  y2038: rusage: use __kernel_old_timeval
  y2038: uapi: change __kernel_time_t to __kernel_old_time_t
  y2038: stat: avoid 'time_t' in 'struct stat'
  y2038: ipc: remove __kernel_time_t reference from headers
  y2038: vdso: powerpc: avoid timespec references
  ...

Pull removal of most of fs/compat_ioctl.c from Arnd Bergmann:
 "As part of the cleanup of some remaining y2038 issues, I came to
  fs/compat_ioctl.c, which still has a couple of commands that need
  support for time64_t.

  In completely unrelated work, I spent time on cleaning up parts of
  this file in the past, moving things out into drivers instead.

  After Al Viro reviewed an earlier version of this series and did a lot
  more of that cleanup, I decided to try to completely eliminate the
  rest of it and move it all into drivers.

  This series incorporates some of Al's work and many patches of my own,
  but in the end stops short of actually removing the last part, which
  is the scsi ioctl handlers. I have patches for those as well, but they
  need more testing or possibly a rewrite"

* tag 'compat-ioctl-5.5' of git://git.kernel.org:/pub/scm/linux/kernel/git/arnd/playground: (42 commits)
  scsi: sd: enable compat ioctls for sed-opal
  pktcdvd: add compat_ioctl handler
  compat_ioctl: move SG_GET_REQUEST_TABLE handling
  compat_ioctl: ppp: move simple commands into ppp_generic.c
  compat_ioctl: handle PPPIOCGIDLE for 64-bit time_t
  compat_ioctl: move PPPIOCSCOMPRESS to ppp_generic
  compat_ioctl: unify copy-in of ppp filters
  tty: handle compat PPP ioctls
  compat_ioctl: move SIOCOUTQ out of compat_ioctl.c
  compat_ioctl: handle SIOCOUTQNSD
  af_unix: add compat_ioctl support
  compat_ioctl: reimplement SG_IO handling
  compat_ioctl: move WDIOC handling into wdt drivers
  fs: compat_ioctl: move FITRIM emulation into file systems
  gfs2: add compat_ioctl support
  compat_ioctl: remove unused convert_in_user macro
  compat_ioctl: remove last RAID handling code
  compat_ioctl: remove /dev/raw ioctl translation
  compat_ioctl: remove PCI ioctl translation
  compat_ioctl: remove joystick ioctl translation
  ...

Pull sysctl system call removal from Eric Biederman:
 "As far as I can tell we have reached the point where no one enables
  the sysctl system call anymore. It still is enabled in a few
  defconfigs but they are mostly the rarely used one and in asking
  people about that it was more cut & paste enabled than anything else.

  This is single commit that just deletes code. Leaving just enough code
  so that the deprecated sysctl warning continues to be printed. If my
  analysis turns out to be wrong and someone actually cares it will be
  easy to revert this commit and have the system call again.

  There was one new xtensa defconfig in linux-next that enabled the
  system call this cycle and when asked about it the maintainer of the
  code replied that it was not enabled on purpose. As of today's
  linux-next tree that defconfig no longer enables the system call.

  What we saw in the review discussion was that if we go a step farther
  than my patch and mess with uapi headers there are pieces of code that
  won't compile, but nothing minds the system call actually disappearing
  from the kernel"

Link: https://lore.kernel.org/lkml/201910011140.EA0181F13@keescook/

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  sysctl: Remove the sysctl system call

Pull seccomp updates from Kees Cook:
 "Mostly this is implementing the new flag SECCOMP_USER_NOTIF_FLAG_CONTINUE,
  but there are cleanups as well.

   - implement SECCOMP_USER_NOTIF_FLAG_CONTINUE (Christian Brauner)

   - fixes to selftests (Christian Brauner)

   - remove secure_computing() argument (Christian Brauner)"

* tag 'seccomp-v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  seccomp: rework define for SECCOMP_USER_NOTIF_FLAG_CONTINUE
  seccomp: fix SECCOMP_USER_NOTIF_FLAG_CONTINUE test
  seccomp: simplify secure_computing()
  seccomp: test SECCOMP_USER_NOTIF_FLAG_CONTINUE
  seccomp: add SECCOMP_USER_NOTIF_FLAG_CONTINUE
  seccomp: avoid overflow in implicit constant conversion

Pull audit updates from Paul Moore:
 "Audit is back for v5.5, albeit with only two patches:

   - Allow for the auditing of suspicious O_CREAT usage via the new
     AUDIT_ANOM_CREAT record.

   - Remove a redundant if-conditional check found during code analysis.
     It's a minor change, but when the pull request is only two patches
     long, you need filler in the pull request email"

[ Heh on the pull request filler. I wish more people tried to write
  better pull request messages, even if maybe it's not worth it for the
  trivial cases ;^)   - Linus ]

* tag 'audit-pr-20191126' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/audit:
  audit: remove redundant condition check in kauditd_thread()
  audit: Report suspicious O_CREAT usage

Pull selinux updates from Paul Moore:
 "Only three SELinux patches for v5.5:

   - Remove the size limit on SELinux policies, the limitation was a
     lingering vestige and no longer necessary.

   - Allow file labeling before the policy is loaded. This should ease
     some of the burden when the policy is initially loaded (no need to
     relabel files), but it should also help enable some new system
     concepts which dynamically create the root filesystem in the
     initrd.

   - Add support for the "greatest lower bound" policy construct which
     is defined as the intersection of the MLS range of two SELinux
     labels"

* tag 'selinux-pr-20191126' of git://git.kernel.org/pub/scm/linux/kernel/git/pcmoore/selinux:
  selinux: default_range glblub implementation
  selinux: allow labeling before policy is loaded
  selinux: remove load size limit

Pull kgdb updates from Daniel Thompson:
 "The major change here is the work from Douglas Anderson that reworks
  the way kdb stack traces are handled on SMP systems. The effect is to
  allow all CPUs to issue their stack trace which reduced the need for
  architecture specific code to support stack tracing.

  Also included are general of clean ups from Doug and myself:

   - Remove some unused variables or arguments.

   - Tidy up the kdb escape handling code and fix a couple of odd corner
     cases.

   - Better ignore escape characters that do not form part of an escape
     sequence. This mostly benefits vi users since they are most likely
     to press escape as a nervous habit but it won't harm anyone else"

* tag 'kgdb-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/danielt/linux:
  kdb: Tweak escape handling for vi users
  kdb: Improve handling of characters from different input sources
  kdb: Remove special case logic from kdb_read()
  kdb: Simplify code to fetch characters from console
  kdb: Tidy up code to handle escape sequences
  kdb: Avoid array subscript warnings on non-SMP builds
  kdb: Fix stack crawling on 'running' CPUs that aren't the master
  kdb: Fix "btc <cpu>" crash if the CPU didn't round up
  kdb: Remove unused "argcount" param from kdb_bt1(); make btaprompt bool
  kgdb: Remove unused DCPU_SSTEP definition

Pull Hyper-V updates from Sasha Levin:

 - support for new VMBus protocols (Andrea Parri)

 - hibernation support (Dexuan Cui)

 - latency testing framework (Branden Bonaby)

 - decoupling Hyper-V page size from guest page size (Himadri Pandya)

* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (22 commits)
  Drivers: hv: vmbus: Fix crash handler reset of Hyper-V synic
  drivers/hv: Replace binary semaphore with mutex
  drivers: iommu: hyperv: Make HYPERV_IOMMU only available on x86
  HID: hyperv: Add the support of hibernation
  hv_balloon: Add the support of hibernation
  x86/hyperv: Implement hv_is_hibernation_supported()
  Drivers: hv: balloon: Remove dependencies on guest page size
  Drivers: hv: vmbus: Remove dependencies on guest page size
  x86: hv: Add function to allocate zeroed page for Hyper-V
  Drivers: hv: util: Specify ring buffer size using Hyper-V page size
  Drivers: hv: Specify receive buffer size using Hyper-V page size
  tools: hv: add vmbus testing tool
  drivers: hv: vmbus: Introduce latency testing
  video: hyperv: hyperv_fb: Support deferred IO for Hyper-V frame buffer driver
  video: hyperv: hyperv_fb: Obtain screen resolution from Hyper-V host
  hv_netvsc: Add the support of hibernation
  hv_sock: Add the support of hibernation
  video: hyperv_fb: Add the support of hibernation
  scsi: storvsc: Add the support of hibernation
  Drivers: hv: vmbus: Add module parameter to cap the VMBus version
  ...

Pull RAS fix from Borislav Petkov:
 "One urgent fix for the thermal throttling machinery: the recent change
  reworking the thermal notifications forgot to mask out read-only and
  reserved bits in the thermal status MSRs, leading to exceptions while
  writing those MSRs.

  The fix takes care of masking out those bits first"

* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mce/therm_throt: Mask out read-only and reserved MSR bits

Pull parisc updates from Helge Deller:
 "Just trivial small updates: An assembler register optimization in the
  inlined networking checksum functions, a compiler warning fix and
  don't unneccesary print a runtime warning on machines which wouldn't
  be affected anyway"

* 'parisc-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: Avoid spurious inequivalent alias kernel error messages
  kexec: Fix pointer-to-int-cast warnings
  parisc: Do not hardcode registers in checksum functions

Pull powerpc updates from Michael Ellerman:
 "Highlights:

   - Infrastructure for secure boot on some bare metal Power9 machines.
     The firmware support is still in development, so the code here
     won't actually activate secure boot on any existing systems.

   - A change to xmon (our crash handler / pseudo-debugger) to restrict
     it to read-only mode when the kernel is lockdown'ed, otherwise it's
     trivial to drop into xmon and modify kernel data, such as the
     lockdown state.

   - Support for KASLR on 32-bit BookE machines (Freescale / NXP).

   - Fixes for our flush_icache_range() and __kernel_sync_dicache()
     (VDSO) to work with memory ranges >4GB.

   - Some reworks of the pseries CMM (Cooperative Memory Management)
     driver to make it behave more like other balloon drivers and enable
     some cleanups of generic mm code.

   - A series of fixes to our hardware breakpoint support to properly
     handle unaligned watchpoint addresses.

  Plus a bunch of other smaller improvements, fixes and cleanups.

  Thanks to: Alastair D'Silva, Andrew Donnellan, Aneesh Kumar K.V,
  Anthony Steinhauser, Cédric Le Goater, Chris Packham, Chris Smart,
  Christophe Leroy, Christopher M. Riedl, Christoph Hellwig, Claudio
  Carvalho, Daniel Axtens, David Hildenbrand, Deb McLemore, Diana
  Craciun, Eric Richter, Geert Uytterhoeven, Greg Kroah-Hartman, Greg
  Kurz, Gustavo L. F. Walbon, Hari Bathini, Harish, Jason Yan, Krzysztof
  Kozlowski, Leonardo Bras, Mathieu Malaterre, Mauro S. M. Rodrigues,
  Michal Suchanek, Mimi Zohar, Nathan Chancellor, Nathan Lynch, Nayna
  Jain, Nick Desaulniers, Oliver O'Halloran, Qian Cai, Rasmus Villemoes,
  Ravi Bangoria, Sam Bobroff, Santosh Sivaraj, Scott Wood, Thomas Huth,
  Tyrel Datwyler, Vaibhav Jain, Valentin Longchamp, YueHaibing"

* tag 'powerpc-5.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (144 commits)
  powerpc/fixmap: fix crash with HIGHMEM
  x86/efi: remove unused variables
  powerpc: Define arch_is_kernel_initmem_freed() for lockdep
  powerpc/prom_init: Use -ffreestanding to avoid a reference to bcmp
  powerpc: Avoid clang warnings around setjmp and longjmp
  powerpc: Don't add -mabi= flags when building with Clang
  powerpc: Fix Kconfig indentation
  powerpc/fixmap: don't clear fixmap area in paging_init()
  selftests/powerpc: spectre_v2 test must be built 64-bit
  powerpc/powernv: Disable native PCIe port management
  powerpc/kexec: Move kexec files into a dedicated subdir.
  powerpc/32: Split kexec low level code out of misc_32.S
  powerpc/sysdev: drop simple gpio
  powerpc/83xx: map IMMR with a BAT.
  powerpc/32s: automatically allocate BAT in setbat()
  powerpc/ioremap: warn on early use of ioremap()
  powerpc: Add support for GENERIC_EARLY_IOREMAP
  powerpc/fixmap: Use __fix_to_virt() instead of fix_to_virt()
  powerpc/8xx: use the fixmapped IMMR in cpm_reset()
  powerpc/8xx: add __init to cpm1 init functions
  ...

Pull ARM updates from Russell King:

 - improve ARM implementation of pfn_valid()

 - various sparse fixes

 - spelling fixes

 - add further ARMv8 debug architecture versions

 - clang fix for decompressor

 - update to generic vDSO

 - remove Brahma-B53 from spectre hardening

 - initialise broadcast hrtimer device

 - use correct nm executable in decompressor

 - remove old mcount et.al.

* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (26 commits)
  ARM: 8940/1: ftrace: remove mcount(),ftrace_caller_old() and ftrace_call_old()
  ARM: 8939/1: kbuild: use correct nm executable
  ARM: 8938/1: kernel: initialize broadcast hrtimer based clock event device
  ARM: 8937/1: spectre-v2: remove Brahma-B53 from hardening
  ARM: 8933/1: replace Sun/Solaris style flag on section directive
  ARM: 8932/1: Add clock_gettime64 entry point
  ARM: 8931/1: Add clock_getres entry point
  ARM: 8930/1: Add support for generic vDSO
  ARM: 8929/1: use APSR_nzcv instead of r15 as mrc operand
  ARM: 8927/1: ARM/hw_breakpoint: add more ARMv8 debug architecture versions support
  ARM: 8918/2: only build return_address() if needed
  ARM: 8928/1: ARM_ERRATA_775420: Spelling s/date/data/
  ARM: 8925/1: tcm: include <asm/tcm.h> for missing declarations
  ARM: 8924/1: tcm: make dtcm_end and itcm_end static
  ARM: 8923/1: mm: include <asm/vga.h> for vga_base
  ARM: 8922/1: parse_dt_topology() rate is pointer to __be32
  ARM: 8920/1: share get_signal_page from signal.c to process.c
  ARM: 8919/1: make unexported functions static
  ARM: 8917/1: mm: include <asm/set_memory.h>
  ARM: 8916/1: mm: make set_section_perms() static
  ...

Merge tag 'nds32-for-linus-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux

Pull nds32 updates from Greentime Hu:

 - code clean up

 - add a nds32 maintainer

* tag 'nds32-for-linus-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/greentime/linux:
  MAINTAINERS: add nds32 maintainer
  nds32: Move static keyword to the front of declaration
  nds32: Fix typo in Kconfig.cpu
  nds32: remove unneeded clean-files for DTB

Merge tag 'notifications-pipe-prep-20191115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs

Pull pipe rework from David Howells:
 "This is my set of preparatory patches for building a general
  notification queue on top of pipes. It makes a number of significant
  changes:

   - It removes the nr_exclusive argument from __wake_up_sync_key() as
     this is always 1. This prepares for the next step:

   - Adds wake_up_interruptible_sync_poll_locked() so that poll can be
     woken up from a function that's holding the poll waitqueue
     spinlock.

   - Change the pipe buffer ring to be managed in terms of unbounded
     head and tail indices rather than bounded index and length. This
     means that reading the pipe only needs to modify one index, not
     two.

   - A selection of helper functions are provided to query the state of
     the pipe buffer, plus a couple to apply updates to the pipe
     indices.

   - The pipe ring is allowed to have kernel-reserved slots. This allows
     many notification messages to be spliced in by the kernel without
     allowing userspace to pin too many pages if it writes to the same
     pipe.

   - Advance the head and tail indices inside the pipe waitqueue lock
     and use wake_up_interruptible_sync_poll_locked() to poke poll
     without having to take the lock twice.

   - Rearrange pipe_write() to preallocate the buffer it is going to
     write into and then drop the spinlock. This allows kernel
     notifications to then be added the ring whilst it is filling the
     buffer it allocated. The read side is stalled because the pipe
     mutex is still held.

   - Don't wake up readers on a pipe if there was already data in it
     when we added more.

   - Don't wake up writers on a pipe if the ring wasn't full before we
     removed a buffer"

* tag 'notifications-pipe-prep-20191115' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
  pipe: Remove sync on wake_ups
  pipe: Increase the writer-wakeup threshold to reduce context-switch count
  pipe: Check for ring full inside of the spinlock in pipe_write()
  pipe: Remove redundant wakeup from pipe_write()
  pipe: Rearrange sequence in pipe_write() to preallocate slot
  pipe: Conditionalise wakeup in pipe_read()
  pipe: Advance tail pointer inside of wait spinlock in pipe_read()
  pipe: Allow pipes to have kernel-reserved slots
  pipe: Use head and tail pointers for the ring, not cursor and length
  Add wake_up_interruptible_sync_poll_locked()
  Remove the nr_exclusive argument from __wake_up_sync_key()
  pipe: Reduce #inclusion of pipe_fs_i.h

Pull fsnotify updates from Jan Kara:
 "Three fsnotify cleanups"

* tag 'fsnotify_for_v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  fsnotify: Add git tree reference to MAINTAINERS
  fsnotify/fdinfo: exportfs_encode_inode_fh() takes pointer as 4th argument
  fsnotify: move declaration of fsnotify_mark_connector_cachep to fsnotify.h

Pull ext2, quota, reiserfs cleanups and fixes from Jan Kara:

 - Refactor the quota on/off kernel internal interfaces (mostly for
   ubifs quota support as ubifs does not want to have inodes holding
   quota information)

 - A few other small quota fixes and cleanups

 - Various small ext2 fixes and cleanups

 - Reiserfs xattr fix and one cleanup

* tag 'for_v5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: (28 commits)
  ext2: code cleanup for descriptor_loc()
  fs/quota: handle overflows of sysctl fs.quota.* and report as unsigned long
  ext2: fix improper function comment
  ext2: code cleanup for ext2_try_to_allocate()
  ext2: skip unnecessary operations in ext2_try_to_allocate()
  ext2: Simplify initialization in ext2_try_to_allocate()
  ext2: code cleanup by calling ext2_group_last_block_no()
  ext2: introduce new helper ext2_group_last_block_no()
  reiserfs: replace open-coded atomic_dec_and_mutex_lock()
  ext2: check err when partial != NULL
  quota: Handle quotas without quota inodes in dquot_get_state()
  quota: Make dquot_disable() work without quota inodes
  quota: Drop dquot_enable()
  fs: Use dquot_load_quota_inode() from filesystems
  quota: Rename vfs_load_quota_inode() to dquot_load_quota_inode()
  quota: Simplify dquot_resume()
  quota: Factor out setup of quota inode
  quota: Check that quota is not dirty before release
  quota: fix livelock in dquot_writeback_dquots
  ext2: don't set *count in the case of failure in ext2_try_to_allocate()
  ...

Pull erofs updates from Gao Xiang:
 "No major kernel updates for this round since I'm fully diving into
  LZMA algorithm internals now to provide high CR XZ algorihm support.
  That needs more work and time for me to get a better compression time.

  Summary:

   - Introduce superblock checksum support

   - Set iowait when waiting I/O for sync decompression path

   - Several code cleanups"

* tag 'erofs-for-5.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/xiang/erofs:
  erofs: remove unnecessary output in erofs_show_options()
  erofs: drop all vle annotations for runtime names
  erofs: support superblock checksum
  erofs: set iowait for sync decompression
  erofs: clean up decompress queue stuffs
  erofs: get rid of __stagingpage_alloc helper
  erofs: remove dead code since managed cache is now built-in
  erofs: clean up collection handling routines