Add dts nodes for 6 EHRPWM instances on SoC. Disable EHRPWM nodes in the
dtsi files and only enable the ones that are actually pinned out on a
given board.

Includes a minor formatting fixup for the serdes node to line up the
nodes appropriately.
Signed-off-by: Vijay Pothukuchi <vijayp@ti.com>
Signed-off-by: Rahul T R <r-ravikumar@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20221107070009.11500-2-r-ravikumar@ti.com

McASP nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the McASP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-12-afd@ti.com

Mailbox nodes defined in the top-level AM65x SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.

As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.

Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-11-afd@ti.com

PCIe nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.

As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-10-afd@ti.com

MCAN nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-9-afd@ti.com

MDIO nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.

As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-8-afd@ti.com

Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).

Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-7-afd@ti.com

ECAP nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-6-afd@ti.com

EPWM nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-5-afd@ti.com

SPI nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-4-afd@ti.com

I2C nodes defined in the top-level AM65x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-3-afd@ti.com

UART nodes defined in the top-level AM65x SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221028142417.10642-2-afd@ti.com

Avoid the following warnings from dt-schema by just renaming the
clock-names string from adc_tsc_fck to fck so it matches the values in
ti,am3359-tscadc.yaml

tscadc@40200000: clock-names:0: 'fck' was expected
Signed-off-by: Matt Ranostay <mranostay@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Judith Mendez <jm@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Link: https://lore.kernel.org/r/20221024151648.394623-1-mranostay@ti.com

I2C nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-13-afd@ti.com

MCAN nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-12-afd@ti.com

Mailbox nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.

As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.

Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-11-afd@ti.com

Mailbox nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.

As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.

Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-10-afd@ti.com

Mailbox nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with a chosen interrupt
and connection to a remote processor.

As the remote processors depend on memory nodes which are only known at
the board integration level, these nodes should only be enabled when
provided with the above information.

Disable the Mailbox nodes in the dtsi files and only enable the ones that
are actually used on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-9-afd@ti.com

UART nodes defined in the top-level J721s2 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-8-afd@ti.com

I2C nodes defined in the top-level J7200 SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-7-afd@ti.com

UART nodes defined in the top-level J7200 SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-6-afd@ti.com

MCAN nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-5-afd@ti.com

MCASP nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCASP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-4-afd@ti.com

I2C nodes defined in the top-level J721e SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-3-afd@ti.com

UART nodes defined in the top-level J721e SoC dtsi files are incomplete
and may not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221020160305.18711-2-afd@ti.com

OSPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the OSPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-11-afd@ti.com

SDHCI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the SDHCI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-10-afd@ti.com

MCAN nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-9-afd@ti.com

MDIO nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.

As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the MDIO nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-8-afd@ti.com

Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).

Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-7-afd@ti.com

ECAP nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information. (These and the EPWM nodes could be used to trigger internal
actions but they are not used like that currently)

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the ECAP nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-6-afd@ti.com

EPWM nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the EPWM nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-5-afd@ti.com

SPI nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the SPI nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-4-afd@ti.com

I2C nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the I2C nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-3-afd@ti.com

UART nodes defined in the top-level AM62x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the UART nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Link: https://lore.kernel.org/r/20221018211533.21335-2-afd@ti.com

The GPMC node defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless it is extended with pinmux information.

As the pinmux is only known at the board integration level, this node
should only be enabled when provided with this information.

Disable the GPMC node in the dtsi file. Since the ELM is made to work
with the GPMC, disable it too.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-11-afd@ti.com

MCAN nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with pinmux
information.

As the pinmux is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the MCAN nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-10-afd@ti.com

MDIO nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a pinmux.

As the attached PHY is only known about at the board integration level,
these nodes should only be enabled when provided with this information.

Disable the MDIO nodes (in both CPSW and ICSSG) in the dtsi files and
only enable the ones that are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-9-afd@ti.com

Although usually integrated as a child of an Ethernet controller, MDIO
IP has an independent pinout. This pinout should be controlled by
the MDIO node (so if it was to be disabled for instance, the pinmux
state would reflect that).

Move the MDIO pins pinmux to the MIDO nodes.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-8-afd@ti.com

PCIe nodes defined in the top-level AM64x SoC dtsi files are incomplete
and will not be functional unless they are extended with a SerDes PHY.
And usually only one of the two modes can be used at a time as they
share a SerDes link.

As the PHY and mode is only known at the board integration level, these
nodes should only be enabled when provided with this information.

Disable the PCIe nodes in the dtsi files and only enable the ones that
are actually pinned out on a given board.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20221017192532.23825-7-afd@ti.com