- 27 Apr, 2022 5 commits
-
-
Hamid Zamani authored
This uses ISO3166 country code and 0 rev on brcmfmac43602 chips. Without this patch 80 MHz width is not selected on 5 GHz channels. Commit a21bf90e ("brcmfmac: use ISO3166 country code and 0 rev as fallback on some devices") provides a way to specify chips for using the fallback case. Before commit 151a7c12 ("Revert "brcmfmac: use ISO3166 country code and 0 rev as fallback"") brcmfmac43602 devices works correctly and for this specific case 80 MHz width is selected. Signed-off-by:
Hamid Zamani <hzamani.cs91@gmail.com> Signed-off-by:
Kalle Valo <kvalo@kernel.org> Link: https://lore.kernel.org/r/20220423111237.60892-1-hzamani.cs91@gmail.com
-
Alexander Wetzel authored
Using not existing queues can panic the kernel with rtl8180/rtl8185 cards. Ignore the skb priority for those cards, they only have one tx queue. Pierre Asselin (pa@panix.com) reported the kernel crash in the Gentoo forum: https://forums.gentoo.org/viewtopic-t-1147832-postdays-0-postorder-asc-start-25.html He also confirmed that this patch fixes the issue. In summary this happened: After updating wpa_supplicant from 2.9 to 2.10 the kernel crashed with a "divide error: 0000" when connecting to an AP. Control port tx now tries to use IEEE80211_AC_VO for the priority, which wpa_supplicants starts to use in 2.10. Since only the rtl8187se part of the driver supports QoS, the priority of the skb is set to IEEE80211_AC_BE (2) by mac80211 for rtl8180/rtl8185 cards. rtl8180 is then unconditionally reading out the priority and finally crashes on drivers/net/wireless/realtek/rtl818x/rtl8180/dev.c line 544 without this patch: idx = (ring->idx + skb_queue_len(&ring->queue)) % ring->entries "ring->entries" is zero for rtl8180/rtl8185 cards, tx_ring[2] never got initialized. Cc: stable@vger.kernel.org Reported-by: pa@panix.com Tested-by: pa@panix.com Signed-off-by:
Alexander Wetzel <alexander@wetzel-home.de> Signed-off-by:
-
Kevin Lo authored
Write the BIT_USB_SUS_DIS bit rather than BIT_BT_DIG_CLK_EN to the REG_HCI_OPT_CTRL register for fixing failure to PCIe power on. Signed-off-by:
Kevin Lo <kevlo@kevlo.org> Acked-by:
Ping-Ke Shih <pkshih@realtek.com> Signed-off-by:
-
Andrejs Cainikovs authored
With a recent change now it is possible to detect the strapping option on SD8997, which allows to pick up a correct firmware for either SDIO-SDIO or SDIO-UART. This commit enables SDIO-UART firmware on SD8997. Signed-off-by:
Andrejs Cainikovs <andrejs.cainikovs@toradex.com> Signed-off-by:
-
Andrejs Cainikovs authored
Some WiFi/Bluetooth modules might have different host connection options, allowing to either use SDIO for both WiFi and Bluetooth, or SDIO for WiFi and UART for Bluetooth. It is possible to detect whether a module has SDIO-SDIO or SDIO-UART connection by reading its host strap register. This change introduces a way to automatically select appropriate firmware depending of the connection method, and removes a need of symlinking or overwriting the original firmware file with a required one. Host strap register used in this commit comes from the NXP driver [1] hosted at Code Aurora. [1] https://source.codeaurora.org/external/imx/linux-imx/tree/drivers/net/wireless/nxp/mxm_wifiex/wlan_src/mlinux/moal_sdio_mmc.c?h=rel_imx_5.4.70_2.3.2&id=688b67b2c7220b01521ffe560da7eee33042c7bd#n1274Signed-off-by:
Alvin Šipraga <alsi@bang-olufsen.dk> Signed-off-by:
-
- 25 Apr, 2022 1 commit
-
-
Srinivasan Raju authored
This is a driver for pureLiFi X, XL, XC devices which use light to transmit data, so they are not compatible with normal Wi-Fi devices. The driver uses separate NL80211_BAND_LC band to distinguish from Wi-Fi. The driver is based on 802.11 softMAC Architecture and uses native 802.11 for configuration and management. Station and Ad-Hoc modes are supported. The driver is compiled and tested in ARM, x86 architectures and compiled in powerpc architecture. This driver implementation has been based on the zd1211rw driver. Signed-off-by:
Srinivasan Raju <srini.raju@purelifi.com> Signed-off-by:
-
- 24 Apr, 2022 14 commits
-
-
Ping-Ke Shih authored
Add some chip_ops to support BT coexistence to work properly. Signed-off-by:
-
Ping-Ke Shih authored
Hardware reports PPDU status containing encoded channel index to driver, so we decode it and then fill freq and band. Signed-off-by:
-
Ping-Ke Shih authored
Read thermal value, and then we can use EWMA thermal value to do RF calibrations if the value is changed over a threshold. Signed-off-by:
-
Ping-Ke Shih authored
Three chip_ops are implemented in this patch. The ::set_txpwr_ctrl and ::init_txpwr_unit are called when we up interface and then configure TX power registers to initial values. The ::set_txpwr_ctrl is to configure 'txpwr_ref' to make basic output TX power of OFDM and CCK rate to be the same. The ::init_txpwr_unit is to initialize TSSI (a method to do TX power compensation depends on thermal value) control and bandedge. The ::set_txpwr is called once switching channel. First, it sets TX power for each rate section (e.g. CCK, OFDM), and then sets TX power offset between 1SS and 2SS rate. Finally, it sets TX power limit to prevent power over regulation. Signed-off-by:
-
Ping-Ke Shih authored
8852c propose new API to configure BB TX/RX path. Without fix patch, it can't transmit any packet. Signed-off-by:
-
Ping-Ke Shih authored
IQK results in hardware has two copies that are used by firmware to switch these two to support MCC. This H2C tell firmware the corresponding channel and band of each IQK results, and currrent one. Signed-off-by:
-
Ping-Ke Shih authored
When disconnecting, it warns somethings after power is off, and we can't do HCI IO. So, add this patch to avoid below messages: rtw89_8852ce 0000:03:00.0: timed out to flush pci txch: 11 rtw89_8852ce 0000:03:00.0: failed to pre-release fwcmd Signed-off-by:
-
Ping-Ke Shih authored
RPP is to report certain skb(s) can be freed, and TX BD indicates which TX descriptors can be freed. Normally, TX BD is happened before RPP. In low power mode, RPP can happen ahead, so change flow to handle this case. Signed-off-by:
-
Ping-Ke Shih authored
In low power mode, we need to pause PCI to configure IMR and PCI ring index registers accordingly, because the regular registers are power-off in this mode. In the transition moment named paused in code, we can't touch ring index, so don't kick off DMA immediately. Instead, queue them into pending queue, and kick off after the moment. There are three low power modes, which are RF off/clock gate/power gate, but PCI enter low power mode in later two modes only. So, add a mask to achieve this. Signed-off-by:
-
Ping-Ke Shih authored
Normally, we re-enable interrupt by napi_poll, but for this special situation, we must turn it on immediately because napi_poll isn't scheduled. Signed-off-by:
-
Ping-Ke Shih authored
In lower power mode, there are very low amount of RX, and it must process in a separated function instead of schedule_napi(), because the existing napi_poll does many things to optimize performance, but not all registers can access in low power mode. The simple way is to use threadfn to process the simple thing. Signed-off-by:
-
Ping-Ke Shih authored
To reclaim TX BD, we need to read hardware reading index to determine if any DMA is complete. Since this IO spends time, do this thing only if we really need it when TX BD has no free buffer corresponding to target skb. The experimental result shows that reading counter decreases from 26,000 to 130 per second. Signed-off-by:
-
Ping-Ke Shih authored
RPWM/CPWM are registers that can set and check low power mode. Since chips use different address, add a field to access them in common flow. Signed-off-by:
-
Ping-Ke Shih authored
8852CE uses different but similar IMR/ISR registers, and its masks are also different in various states, so add config_intr_mask ops to configure masks according to under_recovery or low_power states. Signed-off-by:
-
- 23 Apr, 2022 20 commits
-
-
Po-Hao Huang authored
Disable this capability to avoid timeout errors on certain platforms. Without it, pci bus might stuck and leads to disconnection. Signed-off-by:
Po-Hao Huang <phhuang@realtek.com> Signed-off-by:
Chris Chiu <chris.chiu@canonical.com> Signed-off-by:
-
Po-Hao Huang authored
This avoids below warning and makes compiler happy. error: uninitialized symbol 'tim_offset' Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
Zeal Robot <zealci@zte.com.cn> Signed-off-by:
Minghao Chi <chi.minghao@zte.com.cn> Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Ping-Ke Shih authored
During setting channel, we need to backup/restore and disable/enable some settings. The settings include SCH (scheduler channel), PPDU status report, and RF components, DFS and ADC. Signed-off-by:
-
Ping-Ke Shih authored
BB does many settings during setting channel. First is to configure CCK for 2G channels, and then basic channel and bandwidth settings with a encoded channel index that will report to driver when we receive packets. Configure spur elimination to avoid spur of CSI and NBI tones in certain frequencies. Also, it initializes BT grant to arrange path sharing with BT according to band. Finally, reset TSSI and BB hardware to ensure it stays in initial state. Signed-off-by:
-
Ping-Ke Shih authored
Configure channel and bandwidth of MAC registers to work properly. Signed-off-by:
-
Ping-Ke Shih authored
Prepare functions to configure channel and bandwidth accordingly. Signed-off-by:
-
Ping-Ke Shih authored
HFC is short for HCI flow control, and these parameters is used to configure PCI quota for TX/RX. Signed-off-by:
-
Ping-Ke Shih authored
Define efuse struct to access gain offset, and store them for further use by setting channel. Signed-off-by:
-
Zong-Zhe Yang authored
Add parser for bb gain table and configure bb gain table for 8852c. While ctrl_ch, obtain bb gain error settings and write them to phy. Signed-off-by:
Zong-Zhe Yang <kevin_yang@realtek.com> Signed-off-by:
-
Ping-Ke Shih authored
chip_ops::bb_sethw is to initialize BB settings out of BB parameters tables. Once switching channel or initialing, we do chip_ops::bb_reset to reset hardware counters and states to make things in expectation. Signed-off-by:
-
Ping-Ke Shih authored
TSSI is used to manage TX power with thermal value as a factor. This patch is to configure bandedge to TX proper waveform. Signed-off-by:
-
Zong-Zhe Yang authored
TX power track tables are used to do TX power compensation according to thermal value. In order to work in existing and new chip, add new 6G entries, and change type from u8 to s8. Internal version table is HALRF_027_00_031. Signed-off-by:
-
Ping-Ke Shih authored
TX power depends on rate, but must follow regulation for specific country. Once asked to set channel, we configure registers according to these TX power tables. Signed-off-by:
-
Ping-Ke Shih authored
These parameters are used to initialize BB and RF hardware when we are going to bring up interface and start to transmit and receive. Signed-off-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and pm_runtime_put_noidle. This change is just to simplify the code, no actual functional changes. Reported-by:
-
Minghao Chi authored
Using pm_runtime_resume_and_get is more appropriate for simplifing code Reported-by:
-
