Currently 'struct mlxsw_sp_fid_family' has a field which indicates if
'lag_vid' is valid for use in SFD register.

This is a leftover from using .1Q FIDs instead of emulating them using
.1D FIDs.

Currently when .1Q FIDs are emulated using .1D FIDs, this field is true
for both families, so there is no reason to maintain it.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert MSE (mean-square error) values to SNR and split it SQI (Signal Quality
Indicator) ranges. The used ranges are taken from "OPEN ALLIANCE - Advanced
diagnostic features for 100BASE-T1 automotive Ethernet PHYs"
specification.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220620115601.2035452-1-o.rempel@pengutronix.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Since commit 4c0d2e96 ("net: phy: consider that suspend2ram may cut
off PHY power"), phy_init_hw() invokes both, the ->config_init() and
->config_intr() callbacks.

In the SMSC PHY driver, the latter acknowledges stale interrupts, hence
there's no longer a need to acknowledge them in the former as well.

There are no other callers of ->config_init() besides phy_init_hw().

Drop the redundant code.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/0254edf48bddc96c6248c4414043a3699e94614a.1655716767.git.lukas@wunner.deSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Arun Ramadoss says:

====================
net: dsa: microchip: common spi probe for the ksz series switches - part 1

This patch series aims to refactor the ksz_switch_register routine to have the
common flow for the ksz series switch. At present ksz8795.c & ksz9477.c have
its own dsa_switch_ops and switch detect functionality.
In ksz_switch_register, ksz_dev_ops is assigned based on the function parameter
passed by the individual ksz8/ksz9477 switch register function. And then switch
detect is performed based on the ksz_dev_ops.detect hook.  This patch modifies
the ksz_switch_register such a way that switch detect is performed first, based
on the chip ksz_dev_ops is assigned to ksz_device structure. It ensures the
common flow for the existing as well as LAN937x switches.
In the next series of patch, it will move ksz_dsa_ops and dsa_switch_ops
from ksz8795.c and ksz9477.c to ksz_common.c and have the common spi
probe all the ksz based switches.

Changes in v1
- Splitted the patch series into two.
- Replaced all occurrence of REG_PORT_STATUS_0 and PORT_FIBER_MODE to
  KSZ8_PORT_STATUS_0 and KSZ8_PORT_FIBER_MODE.
- Separated the tag protocol and phy read/write patch into two.
- Assigned the DSA_TAG_PROTO_NONE as the default value for get_tag_protocol hook.
- Reduced the indentation level by using the if(!dev->dev_ops->mirror_add).
- Added the stp_ctrl_reg as a member in ksz_chip_data and removed the member
  in ksz_dev_ops.
- Removed the r_dyn_mac_table, r_sta_mac_table and w_sta_mac_table from the
  ksz_dev_ops since it is used only in the ksz8795.c.

Changes in RFC v2
- Fixed the compilation issue.
- Reduced the patch set to 15.
====================
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220617084255.19376-1-arun.ramadoss@microchip.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

This patch assigns the get_phy_flags & mtu  hook of ksz8795 and ksz9477
in dsa_switch_ops to ksz_common.  For get_phy_flags hooks,checks whether
the chip is ksz8863/kss8793 then it returns error for port1.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This patch makes the dsa_switch_hook for fdbs to use ksz_common.c file.
And from ksz_common, individual switches fdb functions are called using
the dev->dev_ops. And removed the r_dyn_mac_table, r_sta_mac_table and
w_sta_mac_table from ksz_dev_ops as it is used only in ksz8795.c
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ksz_mdb_add/del in ksz_common.c is specific for the ksz8795.c file. The
ksz9477 has its separate ksz9477_port_mdb_add/del functions.  This patch
moves the ksz8795 specific mdb functionality from ksz_common to ksz8795.
And this dsa_switch_ops hooks for ksz8795/ksz9477 are invoked through
the ksz_port_mdb_add/del.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This patch assigns the phylink_get_caps in ksz8795 and ksz9477 to
ksz_phylink_get_caps. And update their mac_capabilities in the
respective ksz_dev_ops.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

At present, P_STP_CTRL register value is passed as parameter to
ksz_port_stp_state from the individual dsa_switch_ops hooks. This patch
update the function to retrieve the register value through the
ksz_chip_data member.
And add the static to ksz_update_port_member since it is not called
outside the ksz_common.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This patch updates the common port mirror add/del dsa_switch_ops in
ksz_common.c. The individual switches implementation is executed based
on the ksz_dev_ops function pointers.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This patch moves the vlan dsa_switch_ops such as vlan_add, vlan_del and
vlan_filtering from the individual files ksz8795.c, ksz9477.c to
ksz_common.c file.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

ksz8795 and ksz9477 implementation on phy read/write hooks are
different. This patch modifies the ksz9477 implementation same as
ksz8795 by updating the ksz9477_dev_ops structure.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

This patch move the dsa hook get_tag_protocol to ksz_common file. And
the tag_protocol is returned based on the dev->chip_id.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

KSZ87xx and KSZ88xx have chip_id representation at reg location 0. And
KSZ9477 compatible switch and LAN937x switch have same chip_id detection
at location 0x01 and 0x02. To have the common switch detect
functionality for ksz switches, ksz_switch_detect function is
introduced.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

The ksz9477_switch_detect performs the detecting the chip id from the
location 0x00 and also check gigabit compatibility check & number of
ports based on the register global_options0. To prepare the common ksz
switch detect function, routine other than chip id read is moved to
ksz9477_switch_init.
Signed-off-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

During initialization of the NFP driver, a file name for loading
application firmware is composed using the NIC's AMDA information and port
type (count and speed). E.g.: "nic_AMDA0145-1012_2x10.nffw".

In practice there may be many variants for each NIC type, and many of the
variants relate to assembly components which do not concern the driver and
application firmware implementation. Yet the current scheme leads to a
different application firmware file name for each variant, because they
have different AMDA information.

To reduce proliferation of content-duplicated application firmware images
or symlinks, the NIC's management firmware will only expose differences
between variants that need different application firmware via a newly
introduced hwinfo, "nffw.partno".

Use of the existing hwinfo, "assembly.partno", is maintained in order to
support for NICs with management firmware that does not expose
"nffw.partno".
Signed-off-by: Yu Xiao <yu.xiao@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/r/20220620103912.46164-1-simon.horman@corigine.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

raw_diag_dump() can use rcu_read_lock() instead of read_lock()

Now the hashinfo lock is only used from process context,
in write mode only, we can convert it to a spinlock,
and we do not need to block BH anymore.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220620100509.3493504-1-eric.dumazet@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Make sure skb_mac_header(), skb_mac_offset() and skb_mac_header_len() uses
are not fooled if the mac header has not been set.

These checks are enabled if CONFIG_DEBUG_NET=y

This commit will likely expose existing bugs in linux networking stacks.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20220620093017.3366713-1-eric.dumazet@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Ido Schimmel says:

====================
mlxsw: Unified bridge conversion - part 1/6

This set starts converting mlxsw to the unified bridge model and mainly
adds new device registers and extends existing ones that will be used in
follow-up patchsets.

High-level summary
==================

The unified bridge model is a new way of managing low-level device
objects such as filtering identifiers (FIDs). The conversion moves a lot
of logic out of the device's firmware towards the driver, but its main
selling point is that it allows to overcome various scalability issues
related to the amount of entries that need to be programmed to the
device.

The only (intended) user visible changes of the conversion are
improvement in resource utilization and ability to support more router
interfaces (RIFs) in Spectrum-{2,3}.

Details
=======

Commit 50853808 ("Merge branch
'mlxsw-Prepare-for-VLAN-aware-bridge-w-VxLAN'") converted mlxsw to
emulate 802.1Q FIDs (represent VLANs in a VLAN-aware bridge) using
802.1D FIDs (represent VLAN-unaware bridges). This was necessary because
at that time VNI could not be assigned to 802.1Q FIDs, which effectively
meant that mlxsw could not support VXLAN with VLAN-aware bridges.

The downside of this approach is that multiple {Port,VID}->FID entries
are required in order to classify incoming traffic to a FID, as opposed
to a single VID->FID entry that can be used with actual 802.1Q FIDs.

For example, if 10 ports are members in the same VLAN-aware bridge and
the same 100 VLANs are configured on each port, then only 100 VID->FID
entries are required with 802.1Q FIDs, whereas 1000 {Port,VID}->FID
entries are required with emulated 802.1Q FIDs.

The above limitation is the result of various assumptions that were made
in the design of the API that was exposed to software. In the unified
bridge model the API is much more "raw" and therefore avoids these
assumptions, allowing software to configure the device in a more
efficient manner.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
"VLAN" type, whereas RIFs constructed on top of VLAN-unaware bridges of
"FID" type.

In other words, the RIF type is derived from the underlying FID type.
VLAN RIFs are used on top of 802.1Q FIDs, whereas FID RIFs are used on
top of 802.1D FIDs.

Currently 802.1Q FIDs are emulated using 802.1D FIDs, and therefore VLAN
RIFs are emulated using FID RIFs.

As part of converting the driver to use unified bridge, 802.1Q FIDs and
VLAN RIFs will be used.

Add the relevant fields to RITR register, add pack() function for VLAN
RIF and rename one field to fit the internal name.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As preparation for unified bridge model, add support for VNI->FID mapping
via SVFA register.

When performing VXLAN encapsulation, the VXLAN header needs to contain a
VNI. This VNI is derived from the FID classification performed on
ingress, through which the ingress RIF is also determined.

Similarly, when performing VXLAN decapsulation, the FID of the packet
needs to be determined. This FID is derived from VNI classification
performed during decapsulation.

In the old model, both entries (i.e., FID->VNI and VNI->FID) were
configured via SFMR.vni.

In the new model, where ingress is separated from egress, ingress
configuration (VNI->FID) is performed via SVFA, while SFMR only
configures egress (FID->VNI).

Add 'vni' field to SVFA, add new mapping table - VNI to FID, add new
pack() function for VNI mapping and edit the comment in SFMR.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

RITR configures the router interface table. As preparation for unified
bridge model, add egress FID field to RITR.

After routing, a packet has to perform a layer-2 lookup using the
destination MAC it got from the routing and a FID.
In the new model, the egress FID is configured by RITR for both sub-port
and FID RIFs.

Add 'efid' field to sub-port router interface and update FID router
interface related comment.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The REIV maps {egress router interface (eRIF), egress_port} -> {vlan ID}.
As preparation for unified bridge model, add REIV register for future use.

In the past, firmware would take care of the above mentioned mapping,
but in the new model this should be done by software using REIV register.

REIV register supports a simultaneous update of 256 ports using
'port_page' field. When 'port_page'=0 the records represent ports
0-255, when 'port_page'=1 the records represent ports 256-511 and so
on.

The register is reserved while using the legacy model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFGC register maps {packet type, bridge type} -> {MID base, table type}.
As preparation for unified bridge model, remove 'mid' field and add
'mid_base' field.

The MID index (index to PGT table which maps MID to local port list and
SMPE index) is a result of 'mid_base' + 'fid_offset'. Using the legacy
bridge model, firmware configures 'mid_base'. However, using the new model,
software is responsible to configure it via SFGC register.

The 'mid_base' is configured per {packet type, bridge type}, for
example, for {Unicast, .1Q}, {Broadcast, .1D}.

Add the field 'mid_base' to SFGC register and increase the length of the
register accordingly.

Remove the field 'mid' as currently it is ignored by the device, its use
is an old leftover.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFMR register creates and configures FIDs. As preparation for unified
bridge model, add a required field for future use.

The PGT (Port Group) table maps multicast ID (MID) to
{local port list, SMPE index} on Spectrum-1 and to {local port list} on
the other ASICs.

In the legacy model, software did not interact with this table directly.
Instead, it was accessed by firmware in response to registers such as
SFTR and SMID.
In the new model, the SFTR register is deprecated and software has full
control over the PGT table using the SMID register.

The configuration of MDB entries (using SFD) is unchanged, but flooding
configuration is completely different.
SFGC register maps {packet type, bridge type} -> {MID base, table type},
then with FID and FID-offset which are configured via SFMR, the MID index
is obtained.

Add the field 'flood_bridge_type' to SFMR, software can separate between
802.1q FIDs and vFIDs using two types which are supported.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFD register configures FDB table. As preparation for unified bridge model,
add some required fields for future use.

In the new model, firmware no longer configures the egress VID, this
responsibility is moved to software. For layer 2 this means that software
needs to determine the egress VID for both unicast and multicast.

For unicast FDB records and unicast LAG FDB records, the VID needs to be
set via new fields in SFD - 'set_vid' and 'vid'.

Add the two mentioned fields for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFMR register creates and configures FIDs. As preparation unified bridge
model, add some required fields for future use.

The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) and the
MPE (Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}

In Spectrum-2 and later ASICs, the SMPE index is an attribute of the FID
and programmed via new fields in SFMR register - 'smpe_valid' and 'smpe'.

Add the two mentioned fields for future use and increase the length of
the register accordingly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SMID register maps multicast ID (MID) into a list of local ports.
As preparation for unified bridge model, add some required fields for
future use.

The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) and the
MPE (Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}

In Spectrum-1, both indexes into the MPE table (local port and SMPE) are
derived from the PGT table. Therefore, the SMPE index needs to be
programmed as part of the PGT entry via new fields in SMID - 'smpe_valid'
and 'smpe'.

Add the two mentioned fields for future use and align the callers of
mlxsw_reg_smid2_pack() to pass zeros for SMPE fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SMPE register maps {egress_port, SMPE index} -> VID.

The device includes two main tables to support layer 2 multicast (i.e.,
MDB and flooding). These are the PGT (Port Group Table) and the
MPE (Multicast Port Egress) table.
- PGT is {MID -> (bitmap of local_port, SPME index)}
- MPE is {(Local port, SMPE index) -> eVID}

In Spectrum-1, the index into the MPE table - called switch multicast to
port egress VID (SMPE) - is derived from the PGT entry, whereas in
Spectrum-2 and later ASICs it is derived from the FID.

In the legacy model, software did not interact with this table as it was
completely hidden in firmware. In the new model, software needs to
populate the table itself in order to map from {Local port, SMPE index} to
an egress VID. This is done using the SMPE register.

Add the register for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Danielle Ratson <danieller@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SVFA register controls the VID to FID mapping and {Port, VID} to FID
mapping for virtualized ports. As preparation for unified bridge model,
add some required fields for future use.

On ingress, after ingress ACL, a packet needs to be classified to a FID.
The key for this lookup can be one of:
1. VID. When port is not in virtual mode.
2. {RQ, VID}. When port is in virtual mode.
3. FID. When FID was set by ingress ACL.

Since RITR no longer performs ingress configuration, the ingress RIF for
the first two entry types needs to be set via new fields in SVFA -
'irif_v' and 'irif'.

Add the two mentioned fields for future use and increase the length of
the register accordingly.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFMR register creates and configures FIDs. As preparation for unified
bridge model, add some required fields for future use.

On ingress, after ingress ACL, a packet needs to be classified to a FID.
The key for this lookup can be one of:
1. VID. When port is not in virtual mode.
2. {RQ, VID}. When port is in virtual mode.
3. FID. When FID was set by ingress ACL.
   For example, via VR_AND_FID_ACTION.

Since RITR no longer performs ingress configuration, the ingress RIF for
the last entry type needs to be set via new fields in SFMR - 'irif_v'
and 'irif'.

Add the two mentioned fields for future use.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFMR register creates and configures FIDs. As preparation for unified
bridge model, add a field for future use.

In the new model, RITR no longer configures the rFID used for sub-port RIFs
and it has to be created by software via SFMR. Such FIDs need to be created
with special flood indication using 'flood_rsp' field. When set, this bit
instructs the device to manage the flooding entries for this FID in a
reserved part of the port group table (PGT).
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

'Commit 6f91f4ba ("vmxnet3: add support for capability registers")'
added support for capability registers. These registers are used
to advertize capabilities of the device.

The patch updated the dev_caps to disable outer checksum offload if
PTCR register does not support it. However, it missed to update
other overlay offloads. This patch fixes this issue.

Fixes: 6f91f4ba ("vmxnet3: add support for capability registers")
Signed-off-by: Ronak Doshi <doshir@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kuniyuki Iwashima says:

====================
raw: Fix nits of RCU conversion series.

The first patch fixes a build error by commit ba44f818 ("raw: use
more conventional iterators"), but it does not land in the net tree,
so this series is targeted to net-next.  The second patch replaces some
hlist functions with sk's helper macros.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

hlist_nulls_add_head_rcu() and hlist_nulls_for_each_entry() have dedicated
macros for sk.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The trailing semicolon causes a compiler error, so let's remove it.

net/ipv4/raw.c: In function ‘raw_icmp_error’:
net/ipv4/raw.c:266:2: error: ISO C90 forbids mixed declarations and code [-Werror=declaration-after-statement]
  266 |  struct hlist_nulls_head *hlist;
      |  ^~~~~~

Fixes: ba44f818 ("raw: use more conventional iterators")
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete the redundant word 'and'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete the redundant word 'and'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Delete the redundant word 'and'.
Signed-off-by: Xiang wangx <wangxiang@cdjrlc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 9386ebcc ("nfp: update nfp_X logging definitions")

The reverted patch was intended to improve logging for the NFP driver by
including information such as the source code file and number in log
messages.

Unfortunately our experience is that this has not improved things as
we had hoped. The resulting logs are inconsistent with (most) other
kernel log messages. And rely on knowledge of the source code version
in order for the extra information to be useful.

Thus, revert the change.

We acknowledge that Jakub Kicinski <kuba@kernel.org> foresaw this problem.
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>