This driver may be used on Baytrail CR platforms where SSP2 is
not available.

Add quirks and routing detection based on work done for RT5640.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

ALC3270 is a low-cost version of RT5645, add ACPI ID
to enable probe and use rt5645 codec driver
Tested on Asus T100HA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

the BIOS reports this codec as RT5640 but it's a rt5670. Use the
quirk mechanism to use the cht_bsw_rt5672 machine driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Fix classic issue of having multiple codecs listed in DSDT
but a single one actually enabled. The previous code did
not handle such errors and could also lead to uninitalized
configurations
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use machine driver initially defined for CherryTrail
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

add ACPI ID 10EC5648 found e.g on Asus X205TA and use
rt5645 driver
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

the BIOS incorrectly reports this codec as 5640 but it is
really a rt5670
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

RT5651 is used on some Cherrytrail platforms, add the ACPI
ID in machine table.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=156191Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add machine entry for HP X2 Pavilion 10-p100.
This notebook contains rt5640 codec, but with ACPI ID "10EC3276".
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Add ACPI ID "10EC3276" for sound card found on notebook HP Pavilion X2 10-p000.
ACPI DSDT Table on this device describes this card as ALC3276, but it is in fact rt5640.
Signed-off-by: Alexandrov Stansilav <neko@nya.ai>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

The existing code assumes a 19.2 MHz MCLK as the default
hardware configuration. This is valid for CherryTrail but
not for Baytrail.

Add explicit MCLK configuration to set the 19.2 clock on/off
depending on DAPM events.

This is a prerequisite step to enable devices with Baytrail
and RT5645 such as Asus X205TA
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'fix/intel' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

The current frame sync polarity definitions are inconsistent in the
Atom/DPCM driver, fix to align with regular ASoC definitions and
update code in platform and machine drivers for RT5640 and RT5651.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

This patch corrects an omission in bytcr_rt5640 and bytcr_rt5651.
All existing machine drivers shall not use .pm_ops to avoid a double
suspend, as initially implemented by 3f2dcbea
("ASoC: Intel: Remove soc pm handling to allow platform driver handle it").
Reported-by: Shrirang Bagul <shrirang.bagul@canonical.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Most of the devices are using stereo speakers so media_loop1 and
sprot_loop default mode should be stereo.

As per default all the routing UCM configuration doesn't enable Post
processing loops it is not impacting curent configurations.
Signed-off-by: Sebastien Guiriec <sebastien.guiriec@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/hdac-hdmi' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

DMA channel(stream tag) used by the HDA link need to programmed in
codec so that codec receives packet from the link associated with the
same channel.

DMA channel is allocated in link BE dai hw_params, the same needs to be
set for the BE codec dai. Instead of using get/set dma_data(), use
dai_ops snd_soc_dai_set_tdm_slot() to set the stream tag.
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In case of hdmi connect/disconnect or when stream need to be route to
multiple monitors, corresponding port and audio infoframe needs to be
reconfigured. Currently all the configuration are done in DAI ops which
results in silence playback.

So use dapm widget event handlers to program audio infoframe and enable
/disable port configuration when widget is power on/off.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Linux 4.10-rc1

With codec read sometimes the pin_sense shows invalid monitor present
and eld_valid. Currently driver polls for few times to get the valid
eld data.

To avoid the latency, Instead of reading ELD from codec, read it
directly from the display driver using audio component framework.
and removed the unused direct codec helper functions.
Signed-off-by: Sandeep Tayal <sandeepx.tayal@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When Ref capture is used during S0IX, only the DSP pipelines
are needed, thus remove the ignore_suspend for WoV streams so
that DMA can be suspended, but keep them for WoV endpoints.
Signed-off-by: Yong Zhi <yong.zhi@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Instead of enabling pin and cvt in pcm_open(), need to restore pin and
cvt state after system resume to restart the playback which is
paused/stopped before system suspend.
So enable pin and cvt in playback_prepare and call prepare when trigger
cmd is paused/started and resume to reconfigure pin and cvt.
Signed-off-by: Sachin Mokashi <sachinx.mokashi@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

In system suspend, the firmware pipelines will be deleted and there
is no need to save the pipeline context. Driver will save the DPIB and
LPIB pointers in suspend.

In system resume, the firmware pipelines will be created again and the
RD/RW pointers in the Firmware buffer points to the base address. So
need to fetch the non-played data again to firmware buffer. LPIB
indicates the HW rendered position.

Instead of setting DPIB as resume point, set it to LPIB to restore from
the HW render position so that DMA would fetch the non-played data one
more time.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

When pipe is pass-through, BE and FE modules are defined inside
a pipe, reset of pipe will be done in FE DAI prepare. So don't
reset in the BE prepare.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Intel Broadwell machine driver will call API snd_soc_set_dmi_name() to
use DMI info to make the sound card long name.

For example, here are the changed long name for two Broadwell-based
machines:
Dell XPS-13(2015): DellInc.-XPS139343-01-0310JH
Intel WilsonBeach: Intel Corp.-BroadwellClientplatform-0.1-WilsonBeachSDS

They still share the same card name "broadwell-rt286".
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Intel DSP platform drivers are used by many different devices but are
difficult for userspace to differentiate. This patch adds an API to allow
the DMI name to be used in the sound card long name, thereby helping
userspace load the correct UCM configuration. Usually machine drivers
uses their own name as the sound card name (short name), and leave the
long name and driver name blank. This API will use the DMI info like
vendor, product and board to make up the card long name. If the machine
driver has already explicitly set the long name, this API will do nothing.

This patch also allows for further differentiation as many devices that
share the same DMI name i.e. Minnowboards, UP boards may be configured
with different codecs or firmwares. The API supports flavoring the DMI
name into the card longname to provide the extra differentiation required
for these devices.

For Use Case Manager (UCM) in the user space, changing card long name by
this API is backward compatible, since the card name does not change. For
a given sound card, even if there is no device-specific UCM configuration
file that uses the card long name, UCM will fall back to load the default
configuration file that uses the card name.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mengdong Lin <mengdong.lin@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

For selected only options the explicit dependencies do not make much sense
becase Kbuild ignores them anyway. Remove them explicitly.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Select DW_DMAC_CORE like the rest of glue drivers do, e.g.
drivers/dma/dw/Kconfig.

While here group selectors under SND_SOC_INTEL_HASWELL and
SND_SOC_INTEL_BAYTRAIL.

Make platforms, which are using a common SST firmware driver, to be
dependent on DMADEVICES.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Rename SND_SST_MFLD_PLATFORM to SND_SST_ATOM_HIFI2_PLATFORM to make it clear
that is not only about Medfield platform.

The new name is derived from Intel Atom and HiFi2. HiFi2 is the DSP version,
it's public information for Intel *Field/*Trail parts, see
https://www.alsa-project.org/main/index.php/Firmware. By combining HiFi2 with
Atom we get a unique non-ambiguous description of the core+DSP hardware for
Intel Medfield through Intel Cherrytrail.
Suggested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

SND_SOC_INTEL_SKYLAKE selects SND_SOC_INTEL_SST already. Thus no need to
duplicate. Remove duplications.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Merge branch 'topic/hda-ext-decouple' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-intel

Check stream decoupled register value with requested value
before decoupling/coupling the stream.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>

Use the optimized dsp_register_poll API to poll the DSP firmware
status register rather than open coding it.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Poll implementation is not quite accurate, especially for smaller
values of timeout or timeout values close to the actual timeout needed

Use jiffies to set the timeout value and time_before() to get the
accurate time. So update the dsp register poll implementation to
provide accurate timeout using jiffies.
Signed-off-by: Jayachandran B <jayachandran.b@intel.com>
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Instead of passing the topology manifest info directly to IPC library,
define the manifest info in topology and use this in IPC Library.
This will remove the dependency on topology interface definition with
IPC library.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

There are literally dozens of Insyde devices with a different
name but with the same audio routing. Use a generic quirk to
match on vendor name only to avoid recurring edits of the
same thing.
Signed-off-by: youling257 <youling257@gmail.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

I am getting the following warning when I build kernel 4.9-git on my
PowerBook G4 with a 32-bit PPC processor:

    AS      arch/powerpc/kernel/misc_32.o
  arch/powerpc/kernel/misc_32.S:299:7: warning: "CONFIG_FSL_BOOKE" is not defined [-Wundef]

This problem is evident after commit 989cea5c ("kbuild: prevent
lib-ksyms.o rebuilds"); however, this change in kbuild only exposes an
error that has been in the code since 2005 when this source file was
created.  That was with commit 9994a338 ("powerpc: Introduce
entry_{32,64}.S, misc_{32,64}.S, systbl.S").

The offending line does not make a lot of sense.  This error does not
seem to cause any errors in the executable, thus I am not recommending
that it be applied to any stable versions.

Thanks to Nicholas Piggin for suggesting this solution.

Fixes: 9994a338 ("powerpc: Introduce entry_{32,64}.S, misc_{32,64}.S, systbl.S")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The timer type simplifications caused a new gcc warning:

  drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
  drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
     elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));

despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.

The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.

Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer type cleanups from Thomas Gleixner:
 "This series does a tree wide cleanup of types related to
  timers/timekeeping.

   - Get rid of cycles_t and use a plain u64. The type is not really
     helpful and caused more confusion than clarity

   - Get rid of the ktime union. The union has become useless as we use
     the scalar nanoseconds storage unconditionally now. The 32bit
     timespec alike storage got removed due to the Y2038 limitations
     some time ago.

     That leaves the odd union access around for no reason. Clean it up.

  Both changes have been done with coccinelle and a small amount of
  manual mopping up"

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  ktime: Get rid of ktime_equal()
  ktime: Cleanup ktime_set() usage
  ktime: Get rid of the union
  clocksource: Use a plain u64 instead of cycle_t