Also do not override any other configuration in this register.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Device driver for Mellanox I2C controller logic, implemented in Lattice
CPLD device.
Device supports:
 - Master mode
 - One physical bus
 - Polling mode

The Kconfig currently controlling compilation of this code is:
drivers/i2c/busses/Kconfig:config I2C_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The ACPI companion of the adapter has to be set for I2C controller
code to read and attach the slave devices described in the ACPI table
with the I2CSerialBus resource descriptor. Used ACPI_COMPANION_SET
macro to set this.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Documentation/CodingStyle recommends to use label names which say
what the goto does or why the goto exists.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Allow more flexibility to bus speed selection. Now if there are I2C
slave connections defined in ACPI the speed of slowest device on the bus
will define the bus speed. However if also "clock-frequency" device
property is defined we should use the slowest of these two.

This is targeted to maker boards where developer may want to connect
slower I2C slave devices to the bus than defined in existing ACPI I2C
slave connections.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Free and Open IPMI use SMBUS BLOCK Read/Write to support SSIF protocol.
However, I2C Designware Core Driver doesn't handle the case at the moment.
The below patch supports this feature.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Check for i2c_adapter_quirks structures that are only stored in the
quirks field of an i2c_adapter structure.  This field is declared
const, so i2c_adapter_quirks structures that have this property can be
declared as const also.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ray Jui <ray.jui@broadcom.com> # for bcm-iproc
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The Kconfig currently controlling compilation of this code is:

drivers/i2c/busses/Kconfig:config I2C_PXA_PCI
drivers/i2c/busses/Kconfig:     def_bool I2C_PXA && X86_32 && PCI && OF

...meaning that it currently is not being built as a module by anyone.

Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.

We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.

Since module_pci_driver() uses the same init level priority as
builtin_pci_driver() the init ordering remains unchanged with
this commit.

Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.

We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This driver allows I2C routing controlled through CPLD select registers on
a wide range of Mellanox systems (CPLD Lattice device).
MUX selection is provided by digital and analog HW. Analog part is not
under SW control.
Digital part is under CPLD control (channel selection/de-selection).

Connectivity schema.
.---.             .-------------.
| l |             |             |-- i2cx1 -- i2cx8
| i |-- i2cn --+--| mlxcpld mux |
| n |          |  |             |-- i2cy1 -- i2cy8
| u |          |  '-------------'
| x |          |         |
'---'          '---------'

i2c-mux-mlxpcld does not necessarily require i2c-mlxcpld. It can be used
along with another bus driver, and still control i2c routing through CPLD
mux selection, in case the system is equipped with CPLD capable of mux
selection control.

The Kconfig currently controlling compilation of this code is:
drivers/i2c/muxes/Kconfig:config I2C_MUX_MLXCPLD
Signed-off-by: Michael Shych <michaelsh@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

As part of an effort to rid the mostly unused second parameter for I2C
related .probe() functions and to conform to other existing frameworks
we're moving over to a temporary replacement .probe() call-back.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This will aid the seamless removal of the current probe()'s, more
commonly unused than used second parameter.  Most I2C drivers can
simply switch over to the new interface, others which have DT
support can use its own matching instead and others can call
i2c_match_id() themselves.  This brings I2C's device probe method
into line with other similar interfaces in the kernel and prevents
the requirement to pass an i2c_device_id table.
Suggested-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: fix rebase conflicts and adapt for dev_pm_domain_{attach,detach}]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

When there was no other way to match a I2C device to driver i2c_match_id()
was exclusively used.  However, now there are other types of tables which
are commonly supplied, matching on an i2c_device_id table is used less
frequently.  Instead of _always_ calling i2c_match_id() from within the
framework, we only need to do so from drivers which have no other way of
matching.  This patch makes i2c_match_id() available to the aforementioned
device drivers.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Currently the I2C framework insists on devices supplying an I2C ID
table.  Many of the devices which do so unnecessarily adding quite a
few wasted lines to kernel code.  This patch allows drivers a means
to 'not' supply the aforementioned table and match on DT match tables
instead.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This function provides a single call for all I2C devices which need to
match firstly using traditional OF means i.e by of_node, then if that
fails we attempt to match using the supplied I2C client name with a
list of supplied compatible strings with the '<vendor>,' string
removed.  The latter is required due to the unruly naming conventions
used currently by I2C devices.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
[Kieran: Fix static inline usage on !CONFIG_OF]
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

A great deal of I2C devices are currently matched via DT node name, and
as such the compatible naming convention of '<vendor>,<device>' has gone
somewhat awry - some nodes don't supply one, some supply an arbitrary
string and others the correct device name with an arbitrary vendor prefix.

In an effort to correct this problem we have to supply a mechanism to
match a device by compatible string AND by simple device name.  This
function strips off the '<vendor>,' part of a supplied compatible string
and attempts to match without it.

It is also used for sysfs, where a user can choose to instantiate a
device on an i2c bus using the sysfs interface by providing a string and
address to match and communicate with the device on the bus. Presently
this string is only matched against the old i2c device id style strings,
even in the presence of full device tree compatible strings with vendor
prefixes.

Providing a vendor-prefixed string to the sysfs interface will not match
against the device tree of_match_device() calls as there is no device
tree node to parse from the sysfs interface.

This function can match both vendor prefixed and stripped compatible
strings on the sysfs interface.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Here we're providing dereference protection for i2c_match_id(), which
saves us having to do it each time it's called.  We're also stripping
out the (now) needless checks in i2c_device_match().  This patch paves
the way for other, similar code trimming.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Kieran Bingham <kieran@bingham.xyz>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Kieran Bingham <kieran@bingham.xyz>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Support a dynamic clock by reading the frequency and setting the
divisor in the transfer function instead of during probe.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Use i2c_adapter->timeout for the completion timeout value. The core
default is 1 second.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Documentation/i2c/i2c-protocol states that Combined transactions should
separate messages with a Start bit and end the whole transaction with a
Stop bit. This patch adds support for issuing only a Start between
messages instead of a Stop followed by a Start.

This implementation differs from downstream i2c-bcm2708 in 2 respects:
- it uses an interrupt to detect that the transfer is active instead
  of using polling. There is no interrupt for Transfer Active, but by
  not prefilling the FIFO it's possible to use the TXW interrupt.
- when resetting/disabling the controller between transfers it writes
  CLEAR to the control register instead of just zero.
  Using just zero gave many errors. This might be the reason why
  downstream had to disable this feature and make it available with a
  module parameter.

I have run thousands of transfers to a DS1307 (rtc), MMA8451 (accel)
and AT24C32 (eeprom) in parallel without problems.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The controller can't support this flag, so remove it.

Documentation/i2c/i2c-protocol states that all of the message is sent:

I2C_M_IGNORE_NAK:
    Normally message is interrupted immediately if there is [NA] from the
    client. Setting this flag treats any [NA] as [A], and all of
    message is sent.

>From the BCM2835 ARM Peripherals datasheet:

    The ERR field is set when the slave fails to acknowledge either
    its address or a data byte written to it.

So when the controller doesn't receive an ack, it sets ERR and raises
an interrupt. In other words, the whole message is not sent.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Writing to an AT24C32 generates on average 2x i2c transfer errors per
32-byte page write. Which amounts to a lot for a 4k write. This is due
to the fact that the chip doesn't respond during it's internal write
cycle when the at24 driver tries and retries the next write.
Only a handful drivers use dev_err() on transfer error, so switch to
dev_dbg() instead.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

If an unexpected TXW or RXR interrupt occurs (msg_buf_remaining == 0),
the driver has no way to fill/drain the FIFO to stop the interrupts.
In this case the controller has to be disabled and the transfer
completed to avoid hang.

(CLKT | ERR) and DONE interrupts are completed in their own paths, and
the controller is disabled in the transfer function after completion.
Unite the code paths and do disabling inside the interrupt routine.

Clear interrupt status bits in the united completion path instead of
trying to do it on every interrupt which isn't necessary.
Only CLKT, ERR and DONE can be cleared that way.

Add the status value to the error value in case of TXW/RXR errors to
distinguish them from the other S_LEN error.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Writing messages larger than the FIFO size results in a hang, rendering
the machine unusable. This is because the RXD status flag is set on the
first interrupt which results in bcm2835_drain_rxfifo() stealing bytes
from the buffer. The controller continues to trigger interrupts waiting
for the missing bytes, but bcm2835_fill_txfifo() has none to give.
In this situation wait_for_completion_timeout() apparently is unable to
stop the madness.

The BCM2835 ARM Peripherals datasheet has this to say about the flags:
  TXD: is set when the FIFO has space for at least one byte of data.
  RXD: is set when the FIFO contains at least one byte of data.
  TXW: is set during a write transfer and the FIFO is less than full.
  RXR: is set during a read transfer and the FIFO is or more full.

Implementing the logic from the downstream i2c-bcm2708 driver solved
the hang problem.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull i2c fix from Wolfram Sang:
 "A bugfix for the I2C core fixing a (rare) race condition"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: core: fix NULL pointer dereference under race condition

Merge branches 'sched-urgent-for-linus' and 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull stack vmap fixups from Thomas Gleixner:
 "Two small patches related to sched_show_task():

   - make sure to hold a reference on the task stack while accessing it

   - remove the thread_saved_pc printout

  .. and add a sanity check into release_task_stack() to catch problems
  with task stack references"

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/core: Remove pointless printout in sched_show_task()
  sched/core: Fix oops in sched_show_task()

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  fork: Add task stack refcounting sanity check and prevent premature task stack freeing

Pull MD fixes from Shaohua Li:
 "There are several bug fixes queued:

   - fix raid5-cache recovery bugs

   - fix discard IO error handling for raid1/10

   - fix array sync writes bogus position to superblock

   - fix IO error handling for raid array with external metadata"

* tag 'md/4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md:
  md: be careful not lot leak internal curr_resync value into metadata. -- (all)
  raid1: handle read error also in readonly mode
  raid5-cache: correct condition for empty metadata write
  md: report 'write_pending' state when array in sync
  md/raid5: write an empty meta-block when creating log super-block
  md/raid5: initialize next_checkpoint field before use
  RAID10: ignore discard error
  RAID1: ignore discard error

Pull SCSI fixes from James Bottomley:
 "Two more important data integrity fixes related to RAID device drivers
  which wrongly throw away the SYNCHRONIZE CACHE command in the non-RAID
  path and a memory leak in the scsi_debug driver"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: arcmsr: Send SYNCHRONIZE_CACHE command to firmware
  scsi: scsi_debug: Fix memory leak if LBP enabled and module is unloaded
  scsi: megaraid_sas: Fix data integrity failure for JBOD (passthrough) devices

Pull input subsystem updates from Dmitry Torokhov.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: psmouse - cleanup Focaltech code
  Input: i8042 - add XMG C504 to keyboard reset table

Pull FireWire (IEEE 1394) fixes from Stefan Richter:

 - add missing input validation to the firewire-net driver. Invalid
   IP-over-1394 encapsulation headers could trigger buffer overflows
   (CVE 2016-8633).

 - IP-over-1394 link fragmentation headers were read and written
   incorrectly, breaking fragmented RX/TX with other OS's stacks.

* tag 'firewire-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394:
  firewire: net: fix fragmented datagram_size off-by-one
  firewire: net: guard against rx buffer overflows

Pull media fixes from Mauro Carvalho Chehab:
 "A series of fixup patches meant to fix the usage of DMA on stack, plus
  one warning fixup"

* tag 'media/v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (32 commits)
  [media] radio-bcm2048: don't ignore errors
  [media] pctv452e: fix semicolon.cocci warnings
  [media] flexcop-usb: don't use stack for DMA
  [media] stk-webcam: don't use stack for DMA
  [media] s2255drv: don't use stack for DMA
  [media] cpia2_usb: don't use stack for DMA
  [media] digitv: handle error code on RC query
  [media] dw2102: return error if su3000_power_ctrl() fails
  [media] nova-t-usb2: handle error code on RC query
  [media] technisat-usb2: use DMA buffers for I2C transfers
  [media] pctv452e: don't call BUG_ON() on non-fatal error
  [media] pctv452e: don't do DMA on stack
  [media] nova-t-usb2: don't do DMA on stack
  [media] gp8psk: don't go past the buffer size
  [media] gp8psk: don't do DMA on stack
  [media] dtv5100: don't do DMA on stack
  [media] dtt200u: handle USB control message errors
  [media] dtt200u: don't do DMA on stack
  [media] dtt200u-fe: handle errors on USB control messages
  [media] dtt200u-fe: don't do DMA on stack
  ...

Pull PCI fixes from Bjorn Helgaas:

 - fix for a Qualcomm driver issue that causes a use-before-set crash

 - fix for DesignWare iATU unroll support that causes external aborts
   when enabling the host bridge

* tag 'pci-v4.9-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: designware: Check for iATU unroll support after initializing host
  PCI: qcom: Fix pp->dev usage before assignment

Pull MTD fixes from Brian Norris:

 - MAINTAINERS updates to reflect some new maintainers/submaintainers.

   We have some great volunteers who've been developing and reviewing
   already. We're going to try a group maintainership model, so
   eventually you'll probably see pull requests from people besides me.

 - NAND fixes from Boris:
    "Three simple fixes:

      - fix a non-critical bug in the gpmi driver
      - fix a bug in the 'automatic NAND timings selection' feature
        introduced in 4.9-rc1
      - fix a false positive uninitialized-var warning"

* tag 'for-linus-20161104' of git://git.infradead.org/linux-mtd:
  mtd: mtk: avoid warning in mtk_ecc_encode
  mtd: nand: Fix data interface configuration logic
  mtd: nand: gpmi: disable the clocks on errors
  MAINTAINERS: add more people to the MTD maintainer team
  MAINTAINERS: add a maintainer for the SPI NOR subsystem

Pull MMC fixes from Ulf Hansson:
 "MMC host:

   - sdhci-msm: Fix error path in probe
   - dw_mmc-pltfm: Avoid NULL pointer dereference"

* tag 'mmc-v4.9-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
  mmc: sdhci-msm: Fix error return code in sdhci_msm_probe()
  mmc: dw_mmc-pltfm: fix the potential NULL pointer dereference

Pull GPIO fixes from Linus Walleij:
 "Some GPIO fixes for the v4.9 series:

   - Fix a nasty file descriptor leak when getting line handles.

   - A fix for a cleanup that seemed innocent but created a problem for
     drivers instantiating several gpiochips for one single OF node.

   - Fix a unpredictable problem using irq_domain_simple() in the mvebu
     driver by converting it to a lineas irqdomain"

* tag 'gpio-v4.9-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/mvebu: Use irq_domain_add_linear
  gpio: of: fix GPIO drivers with multiple gpio_chip for a single node
  gpio: GPIO_GET_LINE{HANDLE,EVENT}_IOCTL: Fix file descriptor leak

Pull nfsd bugfixes from Bruce Fields:
 "Fixes for some recent regressions including fallout from the vmalloc'd
  stack change (after which we can no longer encrypt stuff on the
  stack)"

* tag 'nfsd-4.9-1' of git://linux-nfs.org/~bfields/linux:
  nfsd: Fix general protection fault in release_lock_stateid()
  svcrdma: backchannel cannot share a page for send and rcv buffers
  sunrpc: fix some missing rq_rbuffer assignments
  sunrpc: don't pass on-stack memory to sg_set_buf
  nfsd: move blocked lock handling under a dedicated spinlock

Pull btrfs fixes from Chris Mason:
 "Some fixes that Dave Sterba collected.  We held off on these last week
  because I was focused on the memory corruption testing"

* 'for-4.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  btrfs: fix WARNING in btrfs_select_ref_head()
  Btrfs: remove some no-op casts
  btrfs: pass correct args to btrfs_async_run_delayed_refs()
  btrfs: make file clone aware of fatal signals
  btrfs: qgroup: Prevent qgroup->reserved from going subzero
  Btrfs: kill BUG_ON in do_relocation

Pull overlayfs fixes from Miklos Szeredi:
 "Fix two more POSIX ACL bugs introduced in 4.8 and add a missing fsync
  during copy up to prevent possible data loss"

* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
  ovl: fsync after copy-up
  ovl: fix get_acl() on tmpfs
  ovl: update S_ISGID when setting posix ACLs

Pull drm fixes from Dave Airlie:
 "Fixes for amdgpu, radeon, intel, imx and virtio-gpu.

  This is a bit larger than I'd like, but I had some stuff I meant to
  send for -rc3 but was waiting for the PAT regression fix to land. So
  this is really fixes for rc3 and rc4 in one go.

  There are a set of fixes for an oops we've been seeing around MST
  display unplug, along with more suspend/resume and shutdown fixes for
  amdgpu, one power management follow on fix for nouveau, and set of imx
  fixes, and a single virtio-gpu regression fix"

* tag 'drm-fixes-for-v4.9-rc4' of git://people.freedesktop.org/~airlied/linux: (54 commits)
  virtio-gpu: fix vblank events
  drm/nouveau/acpi: fix check for power resources support
  drm/i915: Fix SKL+ 90/270 degree rotated plane coordinate computation
  drm/i915: Remove two invalid warns
  drm/i915: Rotated view does not need a fence
  drm/i915/fbc: fix CFB size calculation for gen8+
  drm: i915: Wait for fences on new fb, not old
  drm/i915: Clean up DDI DDC/AUX CH sanitation
  drm/i915: Respect alternate_aux_channel for all DDI ports
  drm/i915/gen9: fix watermarks when using the pipe scaler
  drm/i915: Fix mismatched INIT power domain disabling during suspend
  drm/i915: fix a read size argument
  drm/i915: Use fence_write() from rpm resume
  drm/i915/gen9: fix DDB partitioning for multi-screen cases
  drm/i915: workaround sparse warning on variable length arrays
  drm/i915: keep declarations in i915_drv.h
  drm/amd/powerplay: fix bug get wrong evv voltage of Polaris.
  drm/amdgpu/si_dpm: workaround for SI kickers
  drm/radeon/si_dpm: workaround for SI kickers
  drm/amdgpu: fix s3 resume back, uvd dpm randomly can't disable.
  ...