- 01 Dec, 2021 2 commits
-
-
Srinivas Kandagatla authored
Currently each channel is added as list to dai channel list, however there is danger of adding same channel to multiple dai channel list which endups corrupting the other list where its already added. This patch ensures that the channel is actually free before adding to the dai channel list and also ensures that the channel is on the list before deleting it. This check was missing previously, and we did not hit this issue as we were testing very simple usecases with sequence of amixer commands. Fixes: a70d9245 ("ASoC: wcd934x: add capture dapm widgets") Fixes: dd9eb19b ("ASoC: wcd934x: add playback dapm widgets") Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20211130160507.22180-2-srinivas.kandagatla@linaro.orgSigned-off-by:
Mark Brown <broonie@kernel.org>
-
Srinivas Kandagatla authored
msm_routing_put_audio_mixer() can return incorrect value in various scenarios. scenario 1: amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1 amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0 return value is 0 instead of 1 eventhough value was changed scenario 2: amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1 amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 1 return value is 1 instead of 0 eventhough the value was not changed scenario 3: amixer cset iface=MIXER,name='SLIMBUS_0_RX Audio Mixer MultiMedia1' 0 return value is 1 instead of 0 eventhough the value was not changed Fix this by adding checks, so that change notifications are sent correctly. Fixes: e3a33673 ("ASoC: qdsp6: q6routing: Add q6routing driver") Signed-off-by:
-
- 30 Nov, 2021 3 commits
-
-
Hui Wang authored
On the latest Lenovo Thinkstation laptops, we often experience the speaker failure after rebooting, check the dmesg, we could see: sof-audio-pci-intel-tgl 0000:00:1f.3: codec #0 probe error, ret: -5 The analogue codec on the machine is ALC287, then we designed a testcase to reboot and check the codec probing result repeatedly, we found the analogue codec probing always failed at least once within several minutes to several hours (roughly 1 reboot per min). This issue happens on all laptops of this Thinkstation model, but with legacy HDA driver, we couldn't reproduce this issue on those laptops. And so far, this issue is not reproduced on machines which don't belong to this model. We tried to make the hda_dsp_ctrl_init_chip() same as hda_intel_init_chip() which is the controller init routine in the legacy HDA driver, but it didn't help. We found when issue happens, the resp is -1, and if we let driver re-run send_cmd() and get_response(), it will get the correct response 10ec0287, then driver continues the rest work, finally boot to the desktop and all audio function work well. Here adding codec probing retries to 3 times, it could fix the issue on this Thinkstation model, and it doesn't bring impact to other machines. Reviewed-by:
Bard Liao <bard.liao@intel.com> Reviewed-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
Hui Wang <hui.wang@canonical.com> Signed-off-by:
Kai Vehmanen <kai.vehmanen@linux.intel.com> Link: https://lore.kernel.org/r/20211130090606.529348-1-kai.vehmanen@linux.intel.comSigned-off-by:
-
Dan Carpenter authored
The "index" is potentially used without being initialized on the error path. Fixes: fc329c1d ("ASoC: amd: add platform devices for acp6x pdm driver and dmic driver") Signed-off-by:
Dan Carpenter <dan.carpenter@oracle.com> Link: https://lore.kernel.org/r/20211130125633.GA24941@kiliSigned-off-by:
-
Nicolas Frattaroli authored
Previously, the DAI template was used directly, which lead to fun bugs such as "why is my channels_max changing?" when one instantiated more than one i2s_tdm IP block in a device tree. This change makes it so that we instead duplicate the template struct, and then use that. Fixes: 081068fd ("ASoC: rockchip: add support for i2s-tdm controller") Signed-off-by:
Nicolas Frattaroli <frattaroli.nicolas@gmail.com> Link: https://lore.kernel.org/r/20211125084900.417102-1-frattaroli.nicolas@gmail.comSigned-off-by:
-
- 27 Nov, 2021 1 commit
-
-
Mark Brown authored
Merge series from Sameer Pujar <spujar@nvidia.com>: This series addresses following problems: * The runtime PM is not balanced in MVC driver, whenever mute or volume mixer controls are set. * Some of the AHUB devices (SFC, MVC, Mixer, AMX and ADX) use late system sleep. Suspend failure is seen on Jetson TX2 platform.
-
- 26 Nov, 2021 8 commits
-
-
Rob Clark authored
Move the declaration of temporary arrays to somewhere that won't go out of scope before the devm_clk_hw_register() call, lest we be at the whim of the compiler for whether those stack variables get overwritten. Fixes a crash seen with gcc version 11.2.1 20210728 (Red Hat 11.2.1-1) Fixes: bdd229ab ("ASoC: rt5682s: Add driver for ALC5682I-VS codec") Signed-off-by:
Rob Clark <robdclark@chromium.org> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20211118010453.843286-2-robdclark@gmail.comSigned-off-by:
-
Rob Clark authored
Move the declaration of temporary arrays to somewhere that won't go out of scope before the devm_clk_hw_register() call, lest we be at the whim of the compiler for whether those stack variables get overwritten. Fixes a crash seen with gcc version 11.2.1 20210728 (Red Hat 11.2.1-1) Fixes: edbd24ea ("ASoC: rt5682: Drop usage of __clk_get_name()") Signed-off-by:
-
Sameer Pujar authored
The driver currently subscribes for a late system sleep call. The initcall_debug log shows that suspend call for ADX device happens after the parent device (AHUB). This seems to cause suspend failure on Jetson TX2 platform. Also there is no use of having late system sleep specifically for ADX device. Fix the order by using normal system sleep. Fixes: a99ab6f3 ("ASoC: tegra: Add Tegra210 based ADX driver") Cc: stable@vger.kernel.org Signed-off-by:
Sameer Pujar <spujar@nvidia.com> Link: https://lore.kernel.org/r/1637676459-31191-7-git-send-email-spujar@nvidia.comSigned-off-by:
-
Sameer Pujar authored
The driver currently subscribes for a late system sleep call. The initcall_debug log shows that suspend call for AMX device happens after the parent device (AHUB). This seems to cause suspend failure on Jetson TX2 platform. Also there is no use of having late system sleep specifically for AMX device. Fix the order by using normal system sleep. Fixes: 77f7df34 ("ASoC: tegra: Add Tegra210 based AMX driver") Cc: stable@vger.kernel.org Signed-off-by:
-
Sameer Pujar authored
The driver currently subscribes for a late system sleep call. The initcall_debug log shows that suspend call for Mixer device happens after the parent device (AHUB). This seems to cause suspend failure on Jetson TX2 platform. Also there is no use of having late system sleep specifically for Mixer device. Fix the order by using normal system sleep. Fixes: 05bb3d5e ("ASoC: tegra: Add Tegra210 based Mixer driver") Cc: stable@vger.kernel.org Signed-off-by:
-
Sameer Pujar authored
The driver currently subscribes for a late system sleep call. The initcall_debug log shows that suspend call for MVC device happens after the parent device (AHUB). This seems to cause suspend failure on Jetson TX2 platform. Also there is no use of having late system sleep specifically for MVC device. Fix the order by using normal system sleep. Fixes: e539891f ("ASoC: tegra: Add Tegra210 based MVC driver") Cc: stable@vger.kernel.org Signed-off-by:
-
Sameer Pujar authored
The driver currently subscribes for a late system sleep call. The initcall_debug log shows that suspend call for SFC device happens after the parent device (AHUB). This seems to cause suspend failure on Jetson TX2 platform. Also there is no use of having late system sleep specifically for SFC device. Fix the order by using normal system sleep. Fixes: b2f74ec5 ("ASoC: tegra: Add Tegra210 based SFC driver") Cc: stable@vger.kernel.org Signed-off-by:
-
Sameer Pujar authored
After successful application of volume/mute settings via mixer control put calls, the control returns without balancing the runtime PM count. This makes device to be always runtime active. Fix this by allowing control to reach pm_runtime_put() call. Fixes: e539891f ("ASoC: tegra: Add Tegra210 based MVC driver") Cc: stable@vger.kernel.org Signed-off-by:
-
- 25 Nov, 2021 1 commit
-
-
David Heidelberg authored
Both, hardware and drivers does support interrupts. Fix warnings as: arch/arm/boot/dts/tegra30-microsoft-surface-rt-efi.dt.yaml: audio-codec@1a: 'interrupt-parent', 'interrupts' do not match any of the regexes: 'pinctrl-[0-9]+' From schema: /home/runner/work/linux/linux/Documentation/devicetree/bindings/sound/wlf,wm8962.yaml Fixes: cd51b942 ("ASoC: dt-bindings: wlf,wm8962: Convert to json-schema") Signed-off-by:
David Heidelberg <david@ixit.cz> Acked-by:
Charles Keepax <ckeepax@opensource.cirrus.com> Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Link: https://lore.kernel.org/r/20211124155101.59694-1-david@ixit.czSigned-off-by:
-
- 24 Nov, 2021 2 commits
-
-
Ranjani Sridharan authored
It is not unusual for ALSA/ASoC hw_params callbacks to be invoked multiple times. Reset and free the DAI widget before reconfiguring it to keep the DAI widget use_count balanced. Fixes: 0acb48dd ("ASoC: SOF: Intel: hda: make sure DAI widget is set up before IPC") Signed-off-by:
Ranjani Sridharan <ranjani.sridharan@linux.intel.com> Reviewed-by:
Paul Olaru <paul.olaru@oss.nxp.com> Reviewed-by:
-
Lucas Tanure authored
Higher speeds are only supported when PLL is enabled, but the current driver doesn't enable PLL outside of stream use cases, so better to set the lowest SPI speed accepted by the entire device. Move the current frequency set to the spi sub-driver so the whole device can benefit from that speed. spi-max-frequency property could be used, but ACPI systems don't support it, so by setting it in the spi sub-driver probe both Device Trees and ACPI systems are supported. Signed-off-by:
Lucas Tanure <tanureal@opensource.cirrus.com> Reviewed-by:
-
- 23 Nov, 2021 1 commit
-
-
Pierre-Louis Bossart authored
We have configurations for this codec on APL, GLK, JSL and TGL, somehow the information that some designs rely on CometLake was not shared. BugLink: https://github.com/thesofproject/linux/issues/3248 Fixes: 790049fb ("ASoC: Intel: soc-acpi: apl/glk/tgl: add entry for devices based on ES8336 codec") Signed-off-by:
-
- 22 Nov, 2021 2 commits
-
-
Nicolas Frattaroli authored
Without a module alias, autoloading the driver does not occurr when it is built as a module. By adding a module alias, the driver now probes fine automatically and therefore analog audio output works as it should. Fixes: 0d6a04da ("ASoC: Add Rockchip rk817 audio CODEC support") Signed-off-by:
-
Hans de Goede authored
Commit dac7cbd5 ("ASoC: Intel: soc-acpi-byt: shrink tables using compatible IDs") and commit 959ae821 ("ASoC: Intel: soc-acpi-cht: shrink tables using compatible IDs") simplified the match tables in soc-acpi-intel-byt-match.c and soc-acpi-intel-cht-match.c by merging identical entries using the new .comp_ids snd_soc_acpi_mach field to point a single entry to multiple ACPI HIDs and clearing the previously unique per entry .id field. But various machine drivers from sound/soc/intel/boards rely on mach->id in one or more ways, e.g. some drivers contain the following snippets: adev = acpi_dev_get_first_match_dev(mach->id, NULL, -1); pkg_found = snd_soc_acpi_find_package_from_hid(mach->id, ... if (!strncmp(snd_soc_cards[i].codec_id, mach->id, 8)) { ... All of which are broken by the match table shrinking. Make the snd_soc_acpi_mach.id field non const (the storage for the tables already is non const) and on a comps_ids match copy the matching HID to the id field to fix this. Fixes: dac7cbd5 ("ASoC: Intel: soc-acpi-byt: shrink tables using compatible IDs") Fixes: 959ae821 ("ASoC: Intel: soc-acpi-cht: shrink tables using compatible IDs") Suggested-by:
Hans de Goede <hdegoede@redhat.com> Reviewed-by:
-
- 18 Nov, 2021 16 commits
-
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Filter out duplicate updates in Mixer driver. Fixes: 05bb3d5e ("ASoC: tegra: Add Tegra210 based Mixer driver") Signed-off-by:
Jaroslav Kysela <perex@perex.cz> Suggested-by:
Takashi Iwai <tiwai@suse.de> Link: https://lore.kernel.org/r/1637219231-406-17-git-send-email-spujar@nvidia.comSigned-off-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Filter out duplicate updates in ADX driver. Fixes: a99ab6f3 ("ASoC: tegra: Add Tegra210 based ADX driver") Signed-off-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Filter out duplicate updates in AMX driver. Fixes: 77f7df34 ("ASoC: tegra: Add Tegra210 based AMX driver") Signed-off-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Filter out duplicate updates in SFC driver. Fixes: b2f74ec5 ("ASoC: tegra: Add Tegra210 based SFC driver") Signed-off-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Filter out duplicate updates in MVC driver. Fixes: e539891f ("ASoC: tegra: Add Tegra210 based MVC driver") Signed-off-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Update the AHUB driver accordingly. Fixes: 16e1bcc2 ("ASoC: tegra: Add Tegra210 based AHUB driver") Signed-off-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Update the DSPK driver accordingly. Fixes: 327ef647 ("ASoC: tegra: Add Tegra186 based DSPK driver") Suggested-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Update the DMIC driver accordingly. Fixes: 8c8ff982 ("ASoC: tegra: Add Tegra210 based DMIC driver") Suggested-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Update the I2S driver accordingly. Fixes: c0bfa983 ("ASoC: tegra: Add Tegra210 based I2S driver") Suggested-by:
-
Sameer Pujar authored
The kcontrol put callback is expected to return 1 when there is change in HW or when the update is acknowledged by driver. This would ensure that change notifications are sent to subscribed applications. Update the ADMAIF driver accordingly. Fixes: f74028e1 ("ASoC: tegra: Add Tegra210 based ADMAIF driver") Suggested-by:
-
Sameer Pujar authored
The enum controls are expected to use enumerated value type. Update relevant references in control get/put callbacks. Fixes: e539891f ("ASoC: tegra: Add Tegra210 based MVC driver") Suggested-by:
-
Sameer Pujar authored
The enum controls are expected to use enumerated value type. Update relevant references in control get/put callbacks. Fixes: b2f74ec5 ("ASoC: tegra: Add Tegra210 based SFC driver") Suggested-by:
-
Sameer Pujar authored
The enum controls are expected to use enumerated value type. Update relevant references in control get/put callbacks. Fixes: 327ef647 ("ASoC: tegra: Add Tegra186 based DSPK driver") Suggested-by:
-
Sameer Pujar authored
The enum controls are expected to use enumerated value type. Update relevant references in control get/put callbacks. Fixes: 8c8ff982 ("ASoC: tegra: Add Tegra210 based DMIC driver") Suggested-by:
-
Sameer Pujar authored
The enum controls are expected to use enumerated value type. Update relevant references in control get/put callbacks. Fixes: c0bfa983 ("ASoC: tegra: Add Tegra210 based I2S driver") Suggested-by:
-
Sameer Pujar authored
The enum controls are expected to use enumerated value type. Update relevant references in control get/put callbacks. Fixes: f74028e1 ("ASoC: tegra: Add Tegra210 based ADMAIF driver") Suggested-by:
-
- 17 Nov, 2021 1 commit
-
-
Olivier Moysan authored
Fix divider calculation in the case of 32 bits channel configuration, when no master clock is used. Fixes: e4e6ec7b ("ASoC: stm32: Add I2S driver") Signed-off-by:
Olivier Moysan <olivier.moysan@foss.st.com> Link: https://lore.kernel.org/r/20211117104404.3832-1-olivier.moysan@foss.st.comSigned-off-by:
-
- 16 Nov, 2021 3 commits
-
-
Srinivas Kandagatla authored
For some reason we ended up using snd_soc_component_write_field for HPHL and snd_soc_component_update_bits for HPHR, so fix this. Fixes: af3d54b9 ("ASoC: codecs: lpass-rx-macro: add support for lpass rx macro") Signed-off-by:
-
Srinivas Kandagatla authored
Error returned from wcd934x_slim_set_hw_params() are not passed to upper layer, this could be misleading to the user which can start sending stream leading to unnecessary errors. Fix this by properly returning the errors. Fixes: a61f3b4f ("ASoC: wcd934x: add support to wcd9340/wcd9341 codec") Signed-off-by:
-
Srinivas Kandagatla authored
Interrupt Clear registers WCD938X_INTR_CLEAR_0 - WCD938X_INTR_CLEAR_2 are not marked as volatile. This has resulted in a missing interrupt bug while performing runtime pm. regcache_sync() during runtime pm resume path will write to Interrupt clear registers with previous values which basically clears the pending interrupt and actual interrupt handler never sees this interrupt. This issue is more visible with headset plug-in plug-out case compared to headset button. Fix this by adding the Interrupt clear registers to volatile range Fixes: 8d78602a ("ASoC: codecs: wcd938x: add basic driver") Signed-off-by:
-
