- 03 Nov, 2014 25 commits
-
-
nibble.max authored
DVBSky s960ci dvb-s/s2 usb ci box: 1>dvb frontend: M88TS2022(tuner),M88DS3103(demod) 2>usb controller: CY7C86013A 3>ci controller: CIMAX SP2 or its clone. Signed-off-by:
Nibble Max <nibble.max@gmail.com> Reviewed-by:
Olli Salonen <olli.salonen@iki.fi> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com>
-
Mauro Carvalho Chehab authored
Some new devices got added. Update cardlists. Signed-off-by: -
Witold Krecicki authored
Leadtek VC100 is a simple USB capture stick, similar to Yakumo Movie Mixer. Signed-off-by:
Witold Krecicki <wpk+lkml@culm.net> Signed-off-by:
-
Olli Salonen authored
Add an option to disable remote controller for DVBSky devices by specifying the disable_rc option at modprobe. Signed-off-by:
-
Olli Salonen authored
dev_err includes the function name in the log printout, so there is no need to include it manually. While here, fix a small grammatical error in the i2c error message. Signed-off-by:
-
Olli Salonen authored
The dvb-usb-v2 already prints out the MAC address, no need to print it out also here. Signed-off-by:
-
Joe Perches authored
Use dev_err instead of pt1_printk o reduce object code size o remove now unused pt1_printk macro Neaten dev_<level> uses in pt3 o add missing newlines o align arguments o remove unnecessary OOM messages as there's a generic one o typo fixes in messages Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
ほち authored
Toshiba TC90522 is wrongly categorized, fix it Signed-off-by:
ほち, AreMa Inc <knightrider@are.ma> Signed-off-by:
-
Amber Thrall authored
lirc_imon.c and lirc_sasem.c contain an incoming_packet method that is using deprecated printk's. Removed blocks replacing with single dev_info with a %*ph format instead. Signed-off-by:
Amber Thrall <amber.rose.thrall@gmail.com> Signed-off-by:
-
Hans Verkuil authored
Now works with both NTSC and PAL. Tested with CC/XDS for NTSC and teletext/WSS for PAL. The start lines were wrong, the WSS signal wasn't captured and there was no difference between NTSC and PAL w.r.t. the count[] values so NTSC returned way too many lines. Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
-
Hans Verkuil authored
Move pci_disable_device() down otherwise it will complain about an unfreed irq. Signed-off-by:
-
Hans Verkuil authored
Don't mix UNSET and TUNER_ABSENT: you have to pick one or the other. For this driver selecting UNSET to represent an absent tuner resulting in the fewest changes. Signed-off-by:
-
Hans Verkuil authored
Make sure that changing the standard or format is not allowed while one or more of the video, vbi or mpeg vb2 queues are busy. Signed-off-by:
-
Hans Verkuil authored
The vb2 framework knows if streaming is in progress, no need to use a separate field for that. Signed-off-by:
-
Hans Verkuil authored
The width, height and field values are core fields since both vbi, video and blackbird use the same video input. Move those fields to the correct struct. Also fix the field checks in the try_fmt functions: add V4L2_FIELD_SEQ_BT/TB support and map incorrect field values to a correct field value instead of returning an error. Signed-off-by:
-
Hans Verkuil authored
There is no reason to dump the sram code to the kernel log when you stop streaming. Remove those calls to cx88_sram_channel_dump. Signed-off-by:
-
Hans Verkuil authored
The timeout is way too small. Especially complicated command like CX2341X_ENC_STOP_CAPTURE takes much more time than 10 ms. Increase the timeout to 1 second, just as ivtv does (the cx88-blackbird has the same IP core for MPEG compression as ivtv). This solves a nasty issue where STOP_CAPTURE would timeout and the mailbox is left in a busy state, making it impossible to start streaming a second time without reloading the driver first. Signed-off-by:
-
Hans Verkuil authored
btcx-risc is for the bt8xx driver and other drivers shouldn't depend on it. There is no benefit to use that module just to do a pci_zalloc_consistent. Signed-off-by:
-
Hans Verkuil authored
Remove this function. This makes all vb2 queues behave the same, which simplifies comparing the various vb2 queue op implementations. Signed-off-by:
-
Hans Verkuil authored
Don't return -1, return a proper error. Replace dprintk(0, ...) by pr_err since firmware load errors should just be reported as an error. Signed-off-by:
-
Hans Verkuil authored
drivers/media/pci/cx88/cx88-blackbird.c:476:25: warning: cast to restricted __le32 Signed-off-by:
-
Hans Verkuil authored
As usual, this patch is very large due to the fact that half a vb2 conversion isn't possible. And since this affects blackbird, alsa, core, dvb, vbi and video the changes are all over. What made this more difficult was the peculiar way the risc program was setup. The driver allowed for running out of buffers in which case the DMA would stop and restart when the next buffer was queued. There was also a complicated timeout system for when buffers weren't filled. This was replaced by a much simpler scheme where there is always one buffer around and the DMA will just cycle that buffer until a new buffer is queued. In that case the previous buffer will be chained to the new buffer. An interrupt is generated at the start of the new buffer telling the driver that the previous buffer can be passed on to userspace. Much simpler and more robust. Signed-off-by:
-
Hans Verkuil authored
The alsa driver uses videobuf low-level functions that are not available in vb2, so replace them by driver-specific functions. Signed-off-by:
-
Hans Verkuil authored
This list is only used if the width, height and/or format of a buffer has changed, but that can never happen. Remove it and all associated code. Signed-off-by:
-
Hans Verkuil authored
This is a duplicate of dev->fmt and can be removed. As a consequence a lot of tests that check if the format has changed midstream can be removed as well: the format cannot change midstream, so this is a bogus check. Signed-off-by:
-
- 01 Nov, 2014 1 commit
-
-
Matthias Schwarzott authored
The only remaining place that modifies the relevant bit is in function cx231xx_set_Colibri_For_LowIF Signed-off-by:
Matthias Schwarzott <zzam@gentoo.org> Signed-off-by:
-
- 30 Oct, 2014 14 commits
-
-
Matthias Schwarzott authored
The scanning itself just fails (as before this series) but now the correct busses are scanned. Signed-off-by:
Antti Palosaari <crope@iki.fi> Signed-off-by:
-
Matthias Schwarzott authored
All switching should be done by i2c mux adapters. Drop explicit dont_use_port_3 flag. Drop info message about switch. Only the removed code in start_streaming is questionable: It did switch the port_3 flag without accessing i2c in between. Signed-off-by:
-
Matthias Schwarzott authored
I2C bus 1 has internally a switch. Use it as I2C_1_MUX_1 and I2C_1_MUX_3, letting the I2C core handling the switch. Signed-off-by:
-
Matthias Schwarzott authored
change almost all instances of I2C_1 to I2C_1_MUX_3 Only these cases are changed to I2C_1_MUX_1: * All that have dont_use_port_3 set. * CX231XX_BOARD_HAUPPAUGE_EXETER, old code did explicitly not switch to port3. * eeprom access for 930C Signed-off-by:
-
Matthias Schwarzott authored
Get used i2c port from bus_nr and status of port_3 switch. Signed-off-by:
-
Matthias Schwarzott authored
This is used later for is_tuner function that switches i2c behaviour for some tuners. [mchehab@osg.samsung.com: Fix CodingStyle on a multi-line comment] Signed-off-by:
-
Matthias Schwarzott authored
This is a preparation for mapping I2C_1_MUX_1 and I2C_1_MUX_3 later to the seperate muxed i2c adapters. Map mux adapters to I2C_1 for now. Add local variables for i2c_adapters in dvb_init to get line lengths shorter. Signed-off-by:
-
Matthias Schwarzott authored
Replace numbers by the constants of same value and same meaning. Signed-off-by:
-
Matthias Schwarzott authored
Change to I2C_0 ... I2C_2 for the master ports and add I2C_1_MUX_1 and I2C_1_MUX_3 for the muxed ones. V2: Renamed mux adapters to seperate them from master adapters. Signed-off-by:
-
Matthias Schwarzott authored
Instead of using the same name for all 3 i2c physical buses inside cx231xx, name them differently, adding a number to it. This helps to better deal with the logs. [mchehab@osg.samsung.com: removed an unused bus_name var from the original patch] Signed-off-by:
-
Matthias Schwarzott authored
For each i2c master there is a i2c_client allocated that could be deleted now that its only two users have been changed to use their own i2c_client. Signed-off-by:
-
Matthias Schwarzott authored
This is a preparation for deleting the otherwise useless i2c_clients that are allocated for all the i2c master adapters. Signed-off-by:
-
Matthias Schwarzott authored
This is a preparation for deleting the otherwise useless i2c_clients that are allocated for all the i2c master adapters. Signed-off-by:
-
Tomas Melin authored
lockdep reports a potential circular dependecy deadlock when registering input device. Unlock mutex rc_dev->lock prior to calling ir_raw_event_register to avoid the circular dependency since that function also calls input_register_device and rc_open. ====================================================== [ INFO: possible circular locking dependency detected ] 3.17.0-rc7+ #24 Not tainted ------------------------------------------------------- modprobe/647 is trying to acquire lock: (input_mutex){+.+.+.}, at: [<ffffffff812ed81c>] input_register_device+0x2ba/0x381 but task is already holding lock: (ir_raw_handler_lock){+.+.+.}, at: [<ffffffff813186ed>] ir_raw_event_register+0x102/0x190 which lock already depends on the new lock. [cut text] other info that might help us debug this: Chain exists of: input_mutex --> &dev->lock --> ir_raw_handler_lock Possible unsafe locking scenario: CPU0 CPU1 ---- ---- lock(ir_raw_handler_lock); lock(&dev->lock); lock(ir_raw_handler_lock); lock(input_mutex); *** DEADLOCK *** 4 locks held by modprobe/647: #0: (&dev->mutex){......}, at: [<ffffffff812d19f3>] device_lock+0xf/0x11 #1: (&dev->mutex){......}, at: [<ffffffff812d19f3>] device_lock+0xf/0x11 #2: (&dev->lock){+.+.+.}, at: [<ffffffff81317fff>] rc_register_device+0x55d/0x58a #3: (ir_raw_handler_lock){+.+.+.}, at: [<ffffffff813186ed>] ir_raw_event_register+0x102/0x190 stack backtrace: CPU: 0 PID: 647 Comm: modprobe Not tainted 3.17.0-rc7+ #24 Call Trace: [<ffffffff81489d6a>] dump_stack+0x46/0x58 [<ffffffff81487699>] print_circular_bug+0x1f8/0x209 [<ffffffff81074353>] __lock_acquire+0xb54/0xeda [<ffffffff81080f17>] ? console_unlock+0x34d/0x399 [<ffffffff81074c01>] lock_acquire+0xd9/0x111 [<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381 [<ffffffff8148e650>] mutex_lock_interruptible_nested+0x57/0x381 [<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381 [<ffffffff81124e03>] ? kfree+0x7c/0x96 [<ffffffff812ed81c>] ? input_register_device+0x2ba/0x381 [<ffffffff81072531>] ? trace_hardirqs_on+0xd/0xf [<ffffffff812ed81c>] input_register_device+0x2ba/0x381 [<ffffffff8131a537>] ir_mce_kbd_register+0x109/0x139 [<ffffffff81318728>] ir_raw_event_register+0x13d/0x190 [<ffffffff81317e40>] rc_register_device+0x39e/0x58a [<ffffffff81072531>] ? trace_hardirqs_on+0xd/0xf [<ffffffffa00cf2e3>] nvt_probe+0x5ad/0xd52 [nuvoton_cir] [<ffffffffa00ced36>] ? nvt_resume+0x80/0x80 [nuvoton_cir] [<ffffffff81296003>] pnp_device_probe+0x8c/0xa9 [<ffffffff812d1b94>] ? driver_sysfs_add+0x6e/0x93 [<ffffffff812d203a>] driver_probe_device+0xa1/0x1e3 [<ffffffff812d217c>] ? driver_probe_device+0x1e3/0x1e3 [<ffffffff812d21ca>] __driver_attach+0x4e/0x6f [<ffffffff812d075b>] bus_for_each_dev+0x5a/0x8c [<ffffffff812d1b24>] driver_attach+0x19/0x1b [<ffffffff812d1879>] bus_add_driver+0xf1/0x1d6 [<ffffffff812d2817>] driver_register+0x87/0xbe [<ffffffffa0120000>] ? 0xffffffffa0120000 [<ffffffff81295da4>] pnp_register_driver+0x1c/0x1e [<ffffffffa0120010>] nvt_init+0x10/0x1000 [nuvoton_cir] [<ffffffff8100030e>] do_one_initcall+0xea/0x18c [<ffffffff8111497f>] ? __vunmap+0x9d/0xc7 [<ffffffff810a3ca1>] load_module+0x1c21/0x1f2c [<ffffffff810a0bce>] ? show_initstate+0x44/0x44 [<ffffffff810a404e>] SyS_init_module+0xa2/0xb1 [<ffffffff81490ed2>] system_call_fastpath+0x16/0x1b Signed-off-by:Tomas Melin <tomas.melin@iki.fi> Signed-off-by:
-
