- 21 Mar, 2016 40 commits
-
-
Mathias Nyman authored
commit 7895086a upstream. We need to check that a TRB is part of the current segment before calculating its DMA address. Previously a ring segment didn't use a full memory page, and every new ring segment got a new memory page, so the off by one error in checking the upper bound was never seen. Now that we use a full memory page, 256 TRBs (4096 bytes), the off by one didn't catch the case when a TRB was the first element of the next segment. This is triggered if the virtual memory pages for a ring segment are next to each in increasing order where the ring buffer wraps around and causes errors like: [ 106.398223] xhci_hcd 0000:00:14.0: ERROR Transfer event TRB DMA ptr not part of current TD ep_index 0 comp_code 1 [ 106.398230] xhci_hcd 0000:00:14.0: Looking for event-dma fffd3000 trb-start fffd4fd0 trb-end fffd5000 seg-start fffd4000 seg-end fffd4ff0 The trb-end address is one outside the end-seg address. Tested-by:
Arkadiusz Miśkiewicz <arekm@maven.pl> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Zefan Li <lizefan@huawei.com>
-
Felix Fietkau authored
commit 1d62d737 upstream. p->thread.user_cpus_allowed is zero-initialized and is only filled on the first sched_setaffinity call. To avoid adding overhead in the task initialization codepath, simply OR the returned mask in sched_getaffinity with p->cpus_allowed. Signed-off-by:
Felix Fietkau <nbd@openwrt.org> Cc: linux-mips@linux-mips.org Patchwork: https://patchwork.linux-mips.org/patch/10740/Signed-off-by:
Ralf Baechle <ralf@linux-mips.org> Signed-off-by:
-
NeilBrown authored
commit 423f04d6 upstream. raid1_end_read_request() assumes that the In_sync bits are consistent with the ->degaded count. raid1_spare_active updates the In_sync bit before the ->degraded count and so exposes an inconsistency, as does error() So extend the spinlock in raid1_spare_active() and error() to hide those inconsistencies. This should probably be part of Commit: 34cab6f4 ("md/raid1: fix test for 'was read error from last working device'.") as it addresses the same issue. It fixes the same bug and should go to -stable for same reasons. Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
NeilBrown <neilb@suse.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Andy Lutomirski authored
commit 37868fe1 upstream. modify_ldt() has questionable locking and does not synchronize threads. Improve it: redesign the locking and synchronize all threads' LDTs using an IPI on all modifications. This will dramatically slow down modify_ldt in multithreaded programs, but there shouldn't be any multithreaded programs that care about modify_ldt's performance in the first place. This fixes some fallout from the CVE-2015-5157 fixes. Signed-off-by:
Andy Lutomirski <luto@kernel.org> Reviewed-by:
Borislav Petkov <bp@suse.de> Cc: Andrew Cooper <andrew.cooper3@citrix.com> Cc: Andy Lutomirski <luto@amacapital.net> Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com> Cc: Borislav Petkov <bp@alien8.de> Cc: Brian Gerst <brgerst@gmail.com> Cc: Denys Vlasenko <dvlasenk@redhat.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Jan Beulich <jbeulich@suse.com> Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Sasha Levin <sasha.levin@oracle.com> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: security@kernel.org <security@kernel.org> Cc: xen-devel <xen-devel@lists.xen.org> Link: http://lkml.kernel.org/r/4c6978476782160600471bd865b318db34c7b628.1438291540.git.luto@kernel.orgSigned-off-by:
Ingo Molnar <mingo@kernel.org> [bwh: Backported to 3.2: - Adjust context - Drop comment changes in switch_mm() - Drop changes to get_segment_base() in arch/x86/kernel/cpu/perf_event.c - Open-code lockless_dereference(), smp_store_release(), on_each_cpu_mask()] Signed-off-by:
Ben Hutchings <ben@decadent.org.uk> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Andy Lutomirski authored
commit aa1acff3 upstream. The update_va_mapping hypercall can fail if the VA isn't present in the guest's page tables. Under certain loads, this can result in an OOPS when the target address is in unpopulated vmap space. While we're at it, add comments to help explain what's going on. This isn't a great long-term fix. This code should probably be changed to use something like set_memory_ro. Signed-off-by:
-
Alexei Potashnik authored
commit 9547308b upstream. Make sure all non-READ SCSI commands get targ_xfer_tag initialized to 0xffffffff, not just WRITEs. Double-free of a TUR cmd object occurs under the following scenario: 1. TUR received (targ_xfer_tag is uninitialized and left at 0) 2. TUR status sent 3. First unsolicited NOPIN is sent to initiator (gets targ_xfer_tag of 0) 4. NOPOUT for NOPIN (with TTT=0) arrives - its ExpStatSN acks TUR status, TUR is queued for removal - LIO tries to find NOPIN with TTT=0, but finds the same TUR instead, TUR is queued for removal for the 2nd time (Drop unbalanced conditional bracket usage - nab) Signed-off-by:
Alexei Potashnik <alexei@purestorage.com> Signed-off-by:
Spencer Baugh <sbaugh@catern.com> Signed-off-by:
Nicholas Bellinger <nab@linux-iscsi.org> [lizf: Backported to 3.4: - adjust context - leave the braces as it is] Signed-off-by:
-
Alex Deucher authored
commit 0a90a0cf upstream. Fixes a broken hsync start value uncovered by: abc0b144 (drm: Perform basic sanity checks on probed modes) The driver handled the bad hsync start elsewhere, but the above commit prevented it from getting added. bug: https://bugs.freedesktop.org/show_bug.cgi?id=91401Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Yao-Wen Mao authored
commit 2d1cb7f6 upstream. Add the correct dB ranges of Bose Companion 5 and Drangonfly DAC 1.2. Signed-off-by:
Yao-Wen Mao <yaowen@google.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Dirk Behme authored
commit 74472233 upstream. Add support for the Sierra Wireless AR8550 device with USB descriptor 0x1199, 0x68AB. It is common with MC879x modules 1199:683c/683d which also are composite devices with 7 interfaces (0..6) and also MDM62xx based as the AR8550. The major difference are only the interface attributes 02/02/01 on interfaces 3 and 4 on the AR8550. They are vendor specific ff/ff/ff on MC879x modules. lsusb reports: Bus 001 Device 004: ID 1199:68ab Sierra Wireless, Inc. Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1199 Sierra Wireless, Inc. idProduct 0x68ab bcdDevice 0.06 iManufacturer 3 Sierra Wireless, Incorporated iProduct 2 AR8550 iSerial 0 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 198 bNumInterfaces 7 bConfigurationValue 1 iConfiguration 1 Sierra Configuration bmAttributes 0xe0 Self Powered Remote Wakeup MaxPower 0mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x01 EP 1 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x82 EP 2 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 2 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x83 EP 3 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x03 EP 3 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 3 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x84 EP 4 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x85 EP 5 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x04 EP 4 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 4 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 1 AT-commands (v.25ter) iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x86 EP 6 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x05 EP 5 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 5 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x88 EP 8 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x89 EP 9 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x06 EP 6 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 6 bAlternateSetting 0 bNumEndpoints 3 bInterfaceClass 255 Vendor Specific Class bInterfaceSubClass 255 Vendor Specific Subclass bInterfaceProtocol 255 Vendor Specific Protocol iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8a EP 10 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 5 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x8b EP 11 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x07 EP 7 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0200 1x 512 bytes bInterval 32 Device Qualifier (for other device speed): bLength 10 bDescriptorType 6 bcdUSB 2.00 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 bNumConfigurations 1 Device Status: 0x0001 Self Powered Signed-off-by:
Dirk Behme <dirk.behme@de.bosch.com> Cc: Lars Melin <larsm17@gmail.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Marc-André Lureau authored
commit 7932c0bd upstream. While reviewing vhost log code, I found out that log_file is never set. Note: I haven't tested the change (QEMU doesn't use LOG_FD yet). Signed-off-by:
Marc-André Lureau <marcandre.lureau@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
Jiri Pirko authored
commit 42288830 upstream. Fixes: a3138df9 ("[NIU]: Add Sun Neptune ethernet driver.") Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Nicholas Bellinger authored
commit 417c20a9 upstream. This patch fixes a use-after-free bug in iscsit_release_sessions_for_tpg() where se_portal_group->session_lock was incorrectly released/re-acquired while walking the active se_portal_group->tpg_sess_list. The can result in a NULL pointer dereference when iscsit_close_session() shutdown happens in the normal path asynchronously to this code, causing a bogus dereference of an already freed list entry to occur. To address this bug, walk the session list checking for the same state as before, but move entries to a local list to avoid dropping the lock while walking the active list. As before, signal using iscsi_session->session_restatement=1 for those list entries to be released locally by iscsit_free_session() code. Reported-by:
Sunilkumar Nadumuttlu <sjn@datera.io> Cc: Sunilkumar Nadumuttlu <sjn@datera.io> Signed-off-by:
-
Herbert Xu authored
commit f898c522 upstream. This patch removes a bogus BUG_ON in the ablkcipher path that triggers when the destination buffer is different from the source buffer and is scattered. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Joe Stringer authored
commit 4b31814d upstream. When zones were originally introduced, the expectation functions were all extended to perform lookup using the zone. However, insertion was not modified to check the zone. This means that two expectations which are intended to apply for different connections that have the same tuple but exist in different zones cannot both be tracked. Fixes: 5d0aa2cc (netfilter: nf_conntrack: add support for "conntrack zones") Signed-off-by:
Joe Stringer <joestringer@nicira.com> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Tomas Winkler authored
commit 9098f84c upstream. Enclosing mmc_blk_put() is missing in power_ro_lock_show() sysfs handler, let's add it. Fixes: add710ea ("mmc: boot partition ro lock support") Signed-off-by:
Tomas Winkler <tomas.winkler@intel.com> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
NeilBrown authored
commit 34cab6f4 upstream. When we get a read error from the last working device, we don't try to repair it, and don't fail the device. We simple report a read error to the caller. However the current test for 'is this the last working device' is wrong. When there is only one fully working device, it assumes that a non-faulty device is that device. However a spare which is rebuilding would be non-faulty but so not the only working device. So change the test from "!Faulty" to "In_sync". If ->degraded says there is only one fully working device and this device is in_sync, this must be the one. This bug has existed since we allowed read_balance to read from a recovering spare in v3.0 Reported-and-tested-by:
Alexander Lyakas <alex.bolshoy@gmail.com> Fixes: 76073054 ("md/raid1: clean up read_balance.") Signed-off-by:
-
Bernhard Bender authored
commit 96849170 upstream. This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30 touch screen. Due to a missing delay between the RESET and SET_RATE commands, the touch screen may become unresponsive during system startup or driver loading. According to the DMC documentation, a delay is needed after the RESET command to allow the chip to complete its internal initialization. As this delay is not guaranteed, we had a system where the touch screen occasionally did not send any touch data. There was no other indication of the problem. The patch fixes the problem by adding a 150ms delay between the RESET and SET_RATE commands. Suggested-by:
Jakob Mustafa <jakob.mustafa@bytecmed.com> Signed-off-by:
Bernhard Bender <bernhard.bender@bytecmed.com> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Chris Metcalf authored
commit 3f81d244 upstream. We were previously using free_bootmem() and just getting lucky that nothing too bad happened. Signed-off-by:
Chris Metcalf <cmetcalf@ezchip.com> Signed-off-by:
-
Oliver Neukum authored
commit 5fb2c782 upstream. This device automatically switches itself to another mode (0x1405) unless the specific access pattern of Windows is followed in its initial mode. That makes a dirty unmount of the internal storage devices inevitable if they are mounted. So the card reader of such a device should be ignored, lest an unclean removal become inevitable. This replaces an earlier patch that ignored all LUNs of this device. That patch was overly broad. Signed-off-by:
Oliver Neukum <oneukum@suse.com> Reviewed-by:
Lars Melin <larsm17@gmail.com> Signed-off-by:
-
Zhuang Jin Can authored
commit fac4271d upstream. When the link is just waken, it's in Resume state, and driver sets PLS to U0. This refers to Phase 1. Phase 2 refers to when the link has completed the transition from Resume state to U0. With the fix of xhci: report U3 when link is in resume state, it also exposes an issue that usb3 roothub and controller can suspend right after phase 1, and this causes a hard hang in controller. To fix the issue, we need to prevent usb3 bus suspend if any port is resuming in phase 1. [merge separate USB2 and USB3 port resume checking to one -Mathias] Signed-off-by:
Zhuang Jin Can <jin.can.zhuang@intel.com> Signed-off-by:
-
Zhuang Jin Can authored
commit 243292a2 upstream. xhci_hub_report_usb3_link_state() returns pls as U0 when the link is in resume state, and this causes usb core to think the link is in U0 while actually it's in resume state. When usb core transfers control request on the link, it fails with TRB error as the link is not ready for transfer. To fix the issue, report U3 when the link is in resume state, thus usb core knows the link it's not ready for transfer. Signed-off-by:
-
Brian Campbell authored
commit 326124a0 upstream. When resetting a device the number of active TTs may need to be corrected by xhci_update_tt_active_eps, but the number of old active endpoints supplied to it was always zero, so the number of TTs and the bandwidth reserved for them was not updated, and could rise unnecessarily. This affected systems using Intel's Patherpoint chipset, which rely on software bandwidth checking. For example, a Lenovo X230 would lose the ability to use ports on the docking station after enough suspend/resume cycles because the bandwidth calculated would rise with every cycle when a suitable device is attached. The correct number of active endpoints is calculated in the same way as in xhci_reserve_bandwidth. Signed-off-by:
Brian Campbell <bacam@z273.org.uk> Signed-off-by:
-
AMAN DEEP authored
commit 34968106 upstream. virt_dev->num_cached_rings counts on freed ring and is not updated correctly. In xhci_free_or_cache_endpoint_ring() function, the free ring is added into cache and then num_rings_cache is incremented as below: virt_dev->ring_cache[rings_cached] = virt_dev->eps[ep_index].ring; virt_dev->num_rings_cached++; here, free ring pointer is added to a current index and then index is incremented. So current index always points to empty location in the ring cache. For getting available free ring, current index should be decremented first and then corresponding ring buffer value should be taken from ring cache. But In function xhci_endpoint_init(), the num_rings_cached index is accessed before decrement. virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; virt_dev->num_rings_cached--; This is bug in manipulating the index of ring cache. And it should be as below: virt_dev->num_rings_cached--; virt_dev->eps[ep_index].new_ring = virt_dev->ring_cache[virt_dev->num_rings_cached]; virt_dev->ring_cache[virt_dev->num_rings_cached] = NULL; Signed-off-by:
Aman Deep <aman.deep@samsung.com> Signed-off-by:
-
John Youn authored
commit aebda618 upstream. This fixes an issue introduced in commit b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) that made sure we would only use DEPSTARTCFG once per SetConfig. The trick is that we should use one DEPSTARTCFG per SetConfig *OR* SetInterface. SetInterface was completely missed from the original patch. This problem became aparent after commit 76e838c9 (usb: dwc3: gadget: return error if command sent to DEPCMD register fails) added checking of the return status of device endpoint commands. 'Set Endpoint Transfer Resource' command was caught failing occasionally. This is because the Transfer Resource Index was not getting reset during a SET_INTERFACE request. Finally, to fix the issue, was we have to do is make sure that our start_config_issued flag gets reset whenever we receive a SetInterface request. To verify the problem (and its fix), all we have to do is run test 9 from testusb with 'testusb -t 9 -s 2048 -a -c 5000'. Tested-by:
Huang Rui <ray.huang@amd.com> Tested-by:
Subbaraya Sundeep Bhatta <subbaraya.sundeep.bhatta@xilinx.com> Fixes: b23c8439 (usb: dwc3: gadget: fix DEPSTARTCFG for non-EP0 EPs) Signed-off-by:
John Youn <johnyoun@synopsys.com> Signed-off-by:
Felipe Balbi <balbi@ti.com> [lizf: Backported to 3.4: use dev_vdbg() instead of dwc3_trace()] Signed-off-by:
-
NeilBrown authored
commit ee5d004f upstream. The 'event_work' worker used by dm-raid may still be running when the array is stopped. This can result in an oops. So flush the workqueue on which it is run after detaching and before destroying the device. Reported-by:
Heinz Mauelshagen <heinzm@redhat.com> Signed-off-by:
-
NeilBrown authored
commit 5eff3c43 upstream. md_stop() would stop an array, but not free various attached data structures. For internal arrays, these are freed later in do_md_stop() or mddev_put(), but they don't apply for dm-raid arrays. So get md_stop() to free them, and only all it from dm-raid. For internal arrays we now call __md_stop. Reported-by:
majianpeng <majianpeng@gmail.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
-
Edward Hyunkoo Jee authored
commit 0848f642 upstream. When ip_frag_queue() computes positions, it assumes that the passed sk_buff does not contain L2 headers. However, when PACKET_FANOUT_FLAG_DEFRAG is used, IP reassembly functions can be called on outgoing packets that contain L2 headers. Also, IPv4 checksum is not corrected after reassembly. Fixes: 7736d33f ("packet: Add pre-defragmentation support for ipv4 fanouts.") Signed-off-by:
Edward Hyunkoo Jee <edjee@google.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willem de Bruijn <willemb@google.com> Cc: Jerry Chu <hkchu@google.com> Signed-off-by:
-
Tom Hughes authored
commit 4479004e upstream. If we don't do this, and we then fail to recreate the debugfs directory during a mode change, then we will fail later trying to add stations to this now bogus directory: BUG: unable to handle kernel NULL pointer dereference at 0000006c IP: [<c0a92202>] mutex_lock+0x12/0x30 Call Trace: [<c0678ab4>] start_creating+0x44/0xc0 [<c0679203>] debugfs_create_dir+0x13/0xf0 [<f8a938ae>] ieee80211_sta_debugfs_add+0x6e/0x490 [mac80211] Signed-off-by:
Tom Hughes <tom@compton.nu> Signed-off-by:
Johannes Berg <johannes.berg@intel.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Stefan Agner authored
commit 25b401c1 upstream. If a valid power regulator or a dummy regulator is used (which happens to be the case when no regulator is specified), restart_work is queued no matter whether the device was running or not at suspend time. Since work queues get initialized in the ndo_open callback, resuming leads to a NULL pointer exception. Reverse exactly the steps executed at suspend time: - Enable the power regulator in any case - Enable the transceiver regulator if the device was running, even in case we have a power regulator - Queue restart_work only in case the device was running Fixes: bf66f373 ("can: mcp251x: Move to threaded interrupts instead of workqueues.") Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> [lizf: Backported to 3.4: - adjust filename - adjust context] Signed-off-by:
-
Herbert Xu authored
commit 738ac1eb upstream. Shared skbs must not be modified and this is crucial for broadcast and/or multicast paths where we use it as an optimisation to avoid unnecessary cloning. The function skb_recv_datagram breaks this rule by setting peeked without cloning the skb first. This causes funky races which leads to double-free. This patch fixes this by cloning the skb and replacing the skb in the list when setting skb->peeked. Fixes: a59322be ("[UDP]: Only increment counter on first peek/recv") Reported-by:
Konstantin Khlebnikov <khlebnikov@yandex-team.ru> Signed-off-by:
-
Mikulas Patocka authored
commit d531be2c upstream. I have a ST4000DM000 disk. If Linux is booted while the disk is spun down, the command that sets transfer mode causes the disk to spin up. The spin-up takes longer than the default 5s timeout, so the command fails and timeout is reported. Fix this by increasing the timeout to 15s, which is enough for the disk to spin up. Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Arne Fitzenreiter authored
commit cda57b1b upstream. This device loses blocks, often the partition table area, on trim. Disable TRIM. http://pcengines.ch/msata16a.htmSigned-off-by:
Arne Fitzenreiter <arne_f@ipfire.org> Signed-off-by:
-
Arne Fitzenreiter authored
commit 71d126fd upstream. Some devices lose data on TRIM whether queued or not. This patch adds a horkage to disable TRIM. tj: Collapsed unnecessary if() nesting. Signed-off-by:
-
Aleksei Mamlin authored
commit 08c85d2a upstream. Enabling AA on HP 250GB SATA disk VB0250EAVER causes errors: [ 3.788362] ata3.00: failed to enable AA (error_mask=0x1) [ 3.789243] ata3.00: failed to enable AA (error_mask=0x1) Add the ATA_HORKAGE_BROKEN_FPDMA_AA for this specific harddisk. tj: Collected FPDMA_AA entries and updated comment. Signed-off-by:
Aleksei Mamlin <mamlinav@gmail.com> Signed-off-by:
-
Lior Amsalem authored
commit 945b4744 upstream. This commit adds the necessary quirk to make the Marvell 4140 SATA PMP work properly. This PMP doesn't like SRST on port number 4 (the host port) so this commit marks this port as not supporting SRST. Signed-off-by:
Lior Amsalem <alior@marvell.com> Reviewed-by:
Nadav Haklai <nadavh@marvell.com> Signed-off-by:
Thomas Petazzoni <thomas.petazzoni@free-electrons.com> Signed-off-by:
-
Seymour, Shane M authored
commit e7ac6c66 upstream. Two SLES11 SP3 servers encountered similar crashes simultaneously following some kind of SAN/tape target issue: ... qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-801c:3: Abort command issued nexus=3:0:2 -- 1 2002. qla2xxx [0000:81:00.0]-8009:3: DEVICE RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: DEVICE RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8009:3: TARGET RESET ISSUED nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800c:3: do_reset failed for cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-800f:3: TARGET RESET FAILED: Task management failed nexus=3:0:2 cmd=ffff882f89c2c7c0. qla2xxx [0000:81:00.0]-8012:3: BUS RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-802b:3: BUS RESET SUCCEEDED nexus=3:0:2. qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8018:3: ADAPTER RESET ISSUED nexus=3:0:2. qla2xxx [0000:81:00.0]-00af:3: Performing ISP error recovery - ha=ffff88bf04d18000. rport-3:0-0: blocked FC remote port time out: removing target and saving binding qla2xxx [0000:81:00.0]-505f:3: Link is operational (8 Gbps). qla2xxx [0000:81:00.0]-8017:3: ADAPTER RESET SUCCEEDED nexus=3:0:2. rport-2:0-0: blocked FC remote port time out: removing target and saving binding sg_rq_end_io: device detached BUG: unable to handle kernel NULL pointer dereference at 00000000000002a8 IP: [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 PGD 7e6586f067 PUD 7e5af06067 PMD 0 [1739975.390354] Oops: 0002 [#1] SMP CPU 0 ... Supported: No, Proprietary modules are loaded [1739975.390463] Pid: 27965, comm: ABCD Tainted: PF X 3.0.101-0.29-default #1 HP ProLiant DL580 Gen8 RIP: 0010:[<ffffffff8133b268>] [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP: 0018:ffff8839dc1e7c68 EFLAGS: 00010202 RAX: 0000000000000000 RBX: ffff883f0592fc00 RCX: 0000000000000090 RDX: 0000000000000000 RSI: 0000000000000004 RDI: 0000000000000138 RBP: 0000000000000138 R08: 0000000000000010 R09: ffffffff81bd39d0 R10: 00000000000009c0 R11: ffffffff81025790 R12: 0000000000000001 R13: ffff883022212b80 R14: 0000000000000004 R15: ffff883022212b80 FS: 00007f8e54560720(0000) GS:ffff88407f800000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 00000000000002a8 CR3: 0000007e6ced6000 CR4: 00000000001407f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process ABCD (pid: 27965, threadinfo ffff8839dc1e6000, task ffff883592e0c640) Stack: ffff883f0592fc00 00000000fffffffa 0000000000000001 ffff883022212b80 ffff883eff772400 ffffffffa03fa309 0000000000000000 0000000000000000 ffffffffa04003a0 ffff883f063196c0 ffff887f0379a930 ffffffff8115ea1e Call Trace: [<ffffffffa03fa309>] st_open+0x129/0x240 [st] [<ffffffff8115ea1e>] chrdev_open+0x13e/0x200 [<ffffffff811588a8>] __dentry_open+0x198/0x310 [<ffffffff81167d74>] do_last+0x1f4/0x800 [<ffffffff81168fe9>] path_openat+0xd9/0x420 [<ffffffff8116946c>] do_filp_open+0x4c/0xc0 [<ffffffff8115a00f>] do_sys_open+0x17f/0x250 [<ffffffff81468d92>] system_call_fastpath+0x16/0x1b [<00007f8e4f617fd0>] 0x7f8e4f617fcf Code: eb d3 90 48 83 ec 28 40 f6 c6 04 48 89 6c 24 08 4c 89 74 24 20 48 89 fd 48 89 1c 24 4c 89 64 24 10 41 89 f6 4c 89 6c 24 18 74 11 <f0> ff 8f 70 01 00 00 0f 94 c0 45 31 ed 84 c0 74 2b 4c 8d a5 a0 RIP [<ffffffff8133b268>] __pm_runtime_idle+0x28/0x90 RSP <ffff8839dc1e7c68> CR2: 00000000000002a8 Analysis reveals the cause of the crash to be due to STp->device being NULL. The pointer was NULLed via scsi_tape_put(STp) when it calls scsi_tape_release(). In st_open() we jump to err_out after scsi_block_when_processing_errors() completes and returns the device as offline (sdev_state was SDEV_DEL): 1180 /* Open the device. Needs to take the BKL only because of incrementing the SCSI host 1181 module count. */ 1182 static int st_open(struct inode *inode, struct file *filp) 1183 { 1184 int i, retval = (-EIO); 1185 int resumed = 0; 1186 struct scsi_tape *STp; 1187 struct st_partstat *STps; 1188 int dev = TAPE_NR(inode); 1189 char *name; ... 1217 if (scsi_autopm_get_device(STp->device) < 0) { 1218 retval = -EIO; 1219 goto err_out; 1220 } 1221 resumed = 1; 1222 if (!scsi_block_when_processing_errors(STp->device)) { 1223 retval = (-ENXIO); 1224 goto err_out; 1225 } ... 1264 err_out: 1265 normalize_buffer(STp->buffer); 1266 spin_lock(&st_use_lock); 1267 STp->in_use = 0; 1268 spin_unlock(&st_use_lock); 1269 scsi_tape_put(STp); <-- STp->device = 0 after this 1270 if (resumed) 1271 scsi_autopm_put_device(STp->device); 1272 return retval; The ref count for the struct scsi_tape had already been reduced to 1 when the .remove method of the st module had been called. The kref_put() in scsi_tape_put() caused scsi_tape_release() to be called: 0266 static void scsi_tape_put(struct scsi_tape *STp) 0267 { 0268 struct scsi_device *sdev = STp->device; 0269 0270 mutex_lock(&st_ref_mutex); 0271 kref_put(&STp->kref, scsi_tape_release); <-- calls this 0272 scsi_device_put(sdev); 0273 mutex_unlock(&st_ref_mutex); 0274 } In scsi_tape_release() the struct scsi_device in the struct scsi_tape gets set to NULL: 4273 static void scsi_tape_release(struct kref *kref) 4274 { 4275 struct scsi_tape *tpnt = to_scsi_tape(kref); 4276 struct gendisk *disk = tpnt->disk; 4277 4278 tpnt->device = NULL; <<<---- where the dev is nulled 4279 4280 if (tpnt->buffer) { 4281 normalize_buffer(tpnt->buffer); 4282 kfree(tpnt->buffer->reserved_pages); 4283 kfree(tpnt->buffer); 4284 } 4285 4286 disk->private_data = NULL; 4287 put_disk(disk); 4288 kfree(tpnt); 4289 return; 4290 } Although the problem was reported on SLES11.3 the problem appears in linux-next as well. The crash is fixed by reordering the code so we no longer access the struct scsi_tape after the kref_put() is done on it in st_open(). Signed-off-by:
Shane Seymour <shane.seymour@hp.com> Signed-off-by:
Darren Lavender <darren.lavender@hp.com> Reviewed-by:
Johannes Thumshirn <jthumshirn@suse.com> Acked-by:
Kai Mäkisara <kai.makisara@kolumbus.fi> Signed-off-by:
James Bottomley <JBottomley@Odin.com> Signed-off-by:
-
Wengang Wang authored
commit 4fabb594 upstream. Fixes: 3e0249f9 ("RDS/IB: add refcount tracking to struct rds_ib_device") There lacks a dropping on rds_ib_device.refcount in case rds_ib_alloc_fmr failed(mr pool running out). this lead to the refcount overflow. A complain in line 117(see following) is seen. From vmcore: s_ib_rdma_mr_pool_depleted is 2147485544 and rds_ibdev->refcount is -2147475448. That is the evidence the mr pool is used up. so rds_ib_alloc_fmr is very likely to return ERR_PTR(-EAGAIN). 115 void rds_ib_dev_put(struct rds_ib_device *rds_ibdev) 116 { 117 BUG_ON(atomic_read(&rds_ibdev->refcount) <= 0); 118 if (atomic_dec_and_test(&rds_ibdev->refcount)) 119 queue_work(rds_wq, &rds_ibdev->free_work); 120 } fix is to drop refcount when rds_ib_alloc_fmr failed. Signed-off-by:
Wengang Wang <wen.gang.wang@oracle.com> Reviewed-by:
Haggai Eran <haggaie@mellanox.com> Signed-off-by:
Doug Ledford <dledford@redhat.com> Signed-off-by:
-
Heiko Carstens authored
commit e47994dd upstream. The sfpc inline assembly within execve_tail() may incorrectly set bits 28-31 of the sfpc instruction to a value which is not zero. These bits however are currently unused and therefore should be zero so we won't get surprised if these bits will be used in the future. Therefore remove the second operand from the inline assembly. Signed-off-by:
Heiko Carstens <heiko.carstens@de.ibm.com> Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> [lizf: Backported to 3.4: adjust context] Signed-off-by:
-
Julian Anastasov authored
commit 2c17d27c upstream. Incoming packet should be either in backlog queue or in RCU read-side section. Otherwise, the final sequence of flush_backlog() and synchronize_net() may miss packets that can run without device reference: CPU 1 CPU 2 skb->dev: no reference process_backlog:__skb_dequeue process_backlog:local_irq_enable on_each_cpu for flush_backlog => IPI(hardirq): flush_backlog - packet not found in backlog CPU delayed ... synchronize_net - no ongoing RCU read-side sections netdev_run_todo, rcu_barrier: no ongoing callbacks __netif_receive_skb_core:rcu_read_lock - too late free dev process packet for freed dev Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue") Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
Julian Anastasov <ja@ssi.bg> Signed-off-by:
-
Julian Anastasov authored
commit e9e4dd32 upstream. commit 381c759d ("ipv4: Avoid crashing in ip_error") fixes a problem where processed packet comes from device with destroyed inetdev (dev->ip_ptr). This is not expected because inetdev_destroy is called in NETDEV_UNREGISTER phase and packets should not be processed after dev_close_many() and synchronize_net(). Above fix is still required because inetdev_destroy can be called for other reasons. But it shows the real problem: backlog can keep packets for long time and they do not hold reference to device. Such packets are then delivered to upper levels at the same time when device is unregistered. Calling flush_backlog after NETDEV_UNREGISTER_FINAL still accounts all packets from backlog but before that some packets continue to be delivered to upper levels long after the synchronize_net call which is supposed to wait the last ones. Also, as Eric pointed out, processed packets, mostly from other devices, can continue to add new packets to backlog. Fix the problem by moving flush_backlog early, after the device driver is stopped and before the synchronize_net() call. Then use netif_running check to make sure we do not add more packets to backlog. We have to do it in enqueue_to_backlog context when the local IRQ is disabled. As result, after the flush_backlog and synchronize_net sequence all packets should be accounted. Thanks to Eric W. Biederman for the test script and his valuable feedback! Reported-by:
Vittorio Gambaletta <linuxbugs@vittgam.net> Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue") Cc: Eric W. Biederman <ebiederm@xmission.com> Cc: Stephen Hemminger <stephen@networkplumber.org> Signed-off-by:
-
