If a command status of CMD_PROTOCOL_ERR is received, this
information should be conveyed to the SCSI mid layer, not
dropped on the floor.  CMD_PROTOCOL_ERR may be received
from the Smart Array for any commands destined for an external
RAID controller such as a P2000, or commands destined for tape
drives or CD/DVD-ROM drives, if for instance a cable is
disconnected.  This mostly affects multipath configurations, as
disconnecting a cable on a non-multipath configuration is not
going to do anything good regardless of whether CMD_PROTOCOL_ERR
is handled correctly or not.  Not handling CMD_PROTOCOL_ERR
correctly in a multipath configaration involving external RAID
controllers may cause data corruption, so this is quite a serious
bug.  This bug should not normally cause a problem for direct
attached disk storage.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch checks whether HBA is SAS2008 B0 controller.
if it is a SAS2008 B0 controller then it use IO-APIC interrupt instead of MSIX,
as SAS2008 B0 controller doesn't support MSIX interrupts.

[jejb: fix whitespace problems]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@lsi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch fixes the following kernel panic invoked by uninitialized fields
in the chip initialization for the 1G bnx2 iSCSI offload.

One of the bits in the chip initialization is being used by the latest
firmware to control overflow packets.  When this control bit gets enabled
erroneously, it would ultimately result in a bad packet placement which would
cause the bnx2 driver to dereference a NULL ptr in the placement handler.

This can happen under certain stress I/O environment under the Linux
iSCSI offload operation.

This change only affects Broadcom's 5709 chipset.

Unable to handle kernel NULL pointer dereference at 0000000000000008 RIP:
 [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
Pid: 0, comm: swapper Tainted: G     ---- 2.6.18-333.el5debug #2
RIP: 0010:[<ffffffff881f0e7d>]  [<ffffffff881f0e7d>] :bnx2:bnx2_poll_work+0xd0d/0x13c5
RSP: 0018:ffff8101b575bd50  EFLAGS: 00010216
RAX: 0000000000000005 RBX: ffff81007c5fb180 RCX: 0000000000000000
RDX: 0000000000000ffc RSI: 00000000817e8000 RDI: 0000000000000220
RBP: ffff81015bbd7ec0 R08: ffff8100817e9000 R09: 0000000000000000
R10: ffff81007c5fb180 R11: 00000000000000c8 R12: 000000007a25a010
R13: 0000000000000000 R14: 0000000000000005 R15: ffff810159f80558
FS:  0000000000000000(0000) GS:ffff8101afebc240(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000008 CR3: 0000000000201000 CR4: 00000000000006a0
Process swapper (pid: 0, threadinfo ffff8101b5754000, task ffff8101afebd820)
Stack:  000000000000000b ffff810159f80000 0000000000000040 ffff810159f80520
 ffff810159f80500 00cf00cf8008e84b ffffc200100939e0 ffff810009035b20
 0000502900000000 000000be00000001 ffff8100817e7810 00d08101b575bea8
Call Trace:
 <IRQ>  [<ffffffff8008e0d0>] show_schedstat+0x1c2/0x25b
 [<ffffffff881f1886>] :bnx2:bnx2_poll+0xf6/0x231
 [<ffffffff8000c9b9>] net_rx_action+0xac/0x1b1
 [<ffffffff800125a0>] __do_softirq+0x89/0x133
 [<ffffffff8005e30c>] call_softirq+0x1c/0x28
 [<ffffffff8006d5de>] do_softirq+0x2c/0x7d
 [<ffffffff8006d46e>] do_IRQ+0xee/0xf7
 [<ffffffff8005d625>] ret_from_intr+0x0/0xa
 <EOI>  [<ffffffff801a5780>] acpi_processor_idle_simple+0x1c5/0x341
 [<ffffffff801a573d>] acpi_processor_idle_simple+0x182/0x341
 [<ffffffff801a55bb>] acpi_processor_idle_simple+0x0/0x341
 [<ffffffff80049560>] cpu_idle+0x95/0xb8
 [<ffffffff80078b1c>] start_secondary+0x479/0x488
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Cc: stable@vger.kernel.org
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

When using the commands below to write some data to a virtio-scsi LUN of the
QEMU guest(32-bit) with 1G physical memory(qemu -m 1024), the qemu will crash.

        # sudo mkfs.ext4 /dev/sdb  (/dev/sdb is the virtio-scsi LUN.)
        # sudo mount /dev/sdb /mnt
        # dd if=/dev/zero of=/mnt/file bs=1M count=1024

In current implementation, sg_set_buf is called to add buffers to sg list which
is put into the virtqueue eventually. But if there are some HighMem pages in
table->sgl you can not get virtual address by sg_virt. So, sg_virt(sg_elem) may
return NULL value. This will cause QEMU exit when virtqueue_map_sg is called
in QEMU because an invalid GPA is passed by virtqueue.

Two solutions are discussed here:
http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/00675.html

Finally, value assignment approach was adopted because:

Value assignment creates a well-formed scatterlist, because the termination
marker in source sg_list has been set in blk_rq_map_sg(). The last entry of the
source sg_list is just copied to the the last entry in destination list.  Note
that, for now, virtio_ring does not care about the form of the scatterlist and
simply processes the first out_num + in_num consecutive elements of the sg[]
array.

I have tested the patch on my workstation. QEMU would not crash any more.

Cc: <stable@vger.kernel.org> # 3.4: 4fe74b1c: [SCSI] virtio-scsi: SCSI driver
Signed-off-by: Wang Sen <senwang@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Pull workqueue fixes from Tejun Heo:
 "It's later than I'd like but well the timing just didn't work out this
  time.

  There are three bug fixes.  One from before 3.6-rc1 and two from the
  new CPU hotplug code.  Kudos to Lai for discovering all of them and
  providing fixes.

   * Atomicity bug when clearing a flag and setting another.  The two
     operation should have been atomic but wasn't.  This bug has existed
     for a long time but is unlikely to have actually happened.  Fix is
     safe.  Marked for -stable.

   * If CPU hotplug cycles happen back-to-back before workers finish the
     previous cycle, the states could get out of sync and it could get
     stuck.  Fixed by waiting for workers to complete before finishing
     hotplug cycle.

   * While CPU hotplug is in progress, idle workers could be depleted
     which can then lead to deadlock.  I think both happening together
     is highly unlikely but still better to fix it and the fix isn't too
     scary.

  There's another workqueue related regression which reported a few days
  ago:

    https://bugzilla.kernel.org/show_bug.cgi?id=47301

  It's a bit of head scratcher but there is a semi-reliable reproduce
  case, so I'm hoping to resolve it soonish."

* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: fix possible idle worker depletion across CPU hotplug
  workqueue: restore POOL_MANAGING_WORKERS
  workqueue: fix possible deadlock in idle worker rebinding
  workqueue: move WORKER_REBIND clearing in rebind_workers() to the end of the function
  workqueue: UNBOUND -> REBIND morphing in rebind_workers() should be atomic

Pull crypto fixes from Herbert Xu:
 "This fixes the authenc self-test crash as well as a missing export of
  a symbol used by a module."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: authenc - Fix crash with zero-length assoc data
  crypto/caam: Export gen_split_key symbol for other modules

Pull blackfin updates from Bob Liu:
 "One kbuild and a smp build fix."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lliubbo/blackfin:
  kbuild: add symbol prefix arg to kallsyms
  blackfin: smp: adapt to generic smp helpers

The authenc code doesn't deal with zero-length associated data
correctly and ends up constructing a zero-length sg entry which
causes a crash when it's fed into the crypto system.

This patch fixes this by avoiding the code-path that triggers
the SG construction if we have no associated data.

This isn't the most optimal fix as it means that we'll end up
using the fallback code-path even when we could still execute
the digest function.  However, this isn't a big deal as nobody
but the test path would supply zero-length associated data.
Reported-by: Romain Francoise <romain@orebokech.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tested-by: Romain Francoise <romain@orebokech.com>

Commit 1f2bfbd0 ("kbuild: link of
vmlinux moved to a script") introduced in v3.5-rc1 broke kallsyms on
architectures which have symbol prefixes.

The --symbol-prefix argument used to be added to the KALLSYMS command
line from the architecture Makefile, however this isn't picked up by the
new scripts/link-vmlinux.sh. This resulted in symbols like
kallsyms_addresses being added which weren't correctly overriding the
weak symbols such as _kallsyms_addresses. These could then trigger
BUG_ONs in kallsyms code.

This is fixed by removing the KALLSYMS addition from the architecture
Makefile, and using CONFIG_SYMBOL_PREFIX in the link-vmlinux.sh script
to determine whether to add the --symbol-prefix argument.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>

Pull SCSI fixes from James Bottomley:
 "I had actually prepared this fix set before I left for KS + Plumbers,
  so it's been incubating much longer than it should have.  I'll be
  picking up my three week backlog this week, so more fixes will then be
  forthcoming

  This set consist of three minor and one fairly major (the device not
  ready causing offlining problem which is a serious regression
  introduced by the media change update) fixes.

  Signed-off-by: James Bottomley <JBottomley@Parallels.com>"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  [SCSI] Fix 'Device not ready' issue on mpt2sas
  [SCSI] scsi_lib: fix scsi_io_completion's SG_IO error propagation
  [SCSI] megaraid_sas: Move poll_aen_lock initializer
  [SCSI] mpt2sas: Fix for Driver oops, when loading driver with max_queue_depth command line option to a very small value

Pull KVM updates from Avi Kivity:
 "A trio of KVM fixes: incorrect lookup of guest cpuid, an uninitialized
  variable fix, and error path cleanup fix."

* tag 'kvm-3.6-2' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: fix error paths for failed gfn_to_page() calls
  KVM: x86: Check INVPCID feature bit in EBX of leaf 7
  KVM: PIC: fix use of uninitialised variable.

Pull FUSE fixes from Miklos Szeredi:
 "This contains bugfixes for FUSE and CUSE and a compile warning fix."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: fix retrieve length
  fuse: mark variables uninitialized
  cuse: kill connection on initialization error
  cuse: fix fuse_conn_kill()

Pull CIFS fixes from Steve French.

* 'for-linus' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Fix endianness conversion
  CIFS: Fix error handling in cifs_push_mandatory_locks

Pull UDF and ext3 fixes from Jan Kara:
 "One UDF data corruption fix and one ext3 fix where we didn't write
  everything to disk on fsync in one corner case."

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  udf: Fix data corruption for files in ICB
  ext3: Fix fdatasync() for files with only i_size changes

Pull i2c subsystem fixes from Jean Delvare.

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-core: Fix for lockdep validator
  i2c-designware: Fix build error if CONFIG_I2C_DESIGNWARE_PLATFORM=y && CONFIG_I2C_DESIGNWARE_PCI=y
  i2c-i801: Add Device IDs for Intel Lynx Point-LP PCH

To simplify both normal and CPU hotplug paths, worker management is
prevented while CPU hoplug is in progress.  This is achieved by CPU
hotplug holding the same exclusion mechanism used by workers to ensure
there's only one manager per pool.

If someone else seems to be performing the manager role, workers
proceed to execute work items.  CPU hotplug using the same mechanism
can lead to idle worker depletion because all workers could proceed to
execute work items while CPU hotplug is in progress and CPU hotplug
itself wouldn't actually perform the worker management duty - it
doesn't guarantee that there's an idle worker left when it releases
management.

This idle worker depletion, under extreme circumstances, can break
forward-progress guarantee and thus lead to deadlock.

This patch fixes the bug by using separate mechanisms for manager
exclusion among workers and hotplug exclusion.  For manager exclusion,
POOL_MANAGING_WORKERS which was restored by the previous patch is
used.  pool->manager_mutex is now only used for exclusion between the
elected manager and CPU hotplug.  The elected manager won't proceed
without holding pool->manager_mutex.

This ensures that the worker which won the manager position can't skip
managing while CPU hotplug is in progress.  It will block on
manager_mutex and perform management after CPU hotplug is complete.

Note that hotplug may happen while waiting for manager_mutex.  A
manager isn't either on idle or busy list and thus the hoplug code
can't unbind/rebind it.  Make the manager handle its own un/rebinding.

tj: Updated comment and description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

Pull drm fixes from Dave Airlie:
 "Just noticed I hadn't send these out, nothing majorly urgent, I know
  AMD guys have some regression fixes coming soon.

  This contains:
   2 nouveau fixes so it loads on the retina MBP systems properly,
   2 vmwgfx fixes to load the driver earlier, and allow distros config it
   1 error->debug fix in ast
  and Keith was playing with 32-on-64 and decided we may as well stick
  the compat ioctl in all the drivers.  It fixes udl for him."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/vmwgfx: add MODULE_DEVICE_TABLE so vmwgfx loads at boot
  drm/vmwgfx: allow a kconfig option to choose if fbcon is enabled
  drm: use drm_compat_ioctl for 32-bit apps
  drm/ast: drop debug level on error printk
  drm/nv50-/gpio: initialise to vbios defaults during init
  drm/nvd0/disp: hopefully fix selection of 6/8bpc mode on DP outputs

This patch restores POOL_MANAGING_WORKERS which was replaced by
pool->manager_mutex by 60373152 "workqueue: use mutex for global_cwq
manager exclusion".

There's a subtle idle worker depletion bug across CPU hotplug events
and we need to distinguish an actual manager and CPU hotplug
preventing management.  POOL_MANAGING_WORKERS will be used for the
former and manager_mutex the later.

This patch just lays POOL_MANAGING_WORKERS on top of the existing
manager_mutex and doesn't introduce any synchronization changes.  The
next patch will update it.

Note that this patch fixes a non-critical anomaly where
too_many_workers() may return %true spuriously while CPU hotplug is in
progress.  While the issue could schedule idle timer spuriously, it
didn't trigger any actual misbehavior.

tj: Rewrote patch description.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

This bug was triggered:
[ 4220.198458] BUG: unable to handle kernel paging request at fffffffffffffffe
[ 4220.203907] IP: [<ffffffff81104d85>] put_page+0xf/0x34
......
[ 4220.237326] Call Trace:
[ 4220.237361]  [<ffffffffa03830d0>] kvm_arch_destroy_vm+0xf9/0x101 [kvm]
[ 4220.237382]  [<ffffffffa036fe53>] kvm_put_kvm+0xcc/0x127 [kvm]
[ 4220.237401]  [<ffffffffa03702bc>] kvm_vcpu_release+0x18/0x1c [kvm]
[ 4220.237407]  [<ffffffff81145425>] __fput+0x111/0x1ed
[ 4220.237411]  [<ffffffff8114550f>] ____fput+0xe/0x10
[ 4220.237418]  [<ffffffff81063511>] task_work_run+0x5d/0x88
[ 4220.237424]  [<ffffffff8104c3f7>] do_exit+0x2bf/0x7ca

The test case:

	printf(fmt, ##args);		\
	exit(-1);} while (0)

static int create_vm(void)
{
	int sys_fd, vm_fd;

	sys_fd = open("/dev/kvm", O_RDWR);
	if (sys_fd < 0)
		die("open /dev/kvm fail.\n");

	vm_fd = ioctl(sys_fd, KVM_CREATE_VM, 0);
	if (vm_fd < 0)
		die("KVM_CREATE_VM fail.\n");

	return vm_fd;
}

static int create_vcpu(int vm_fd)
{
	int vcpu_fd;

	vcpu_fd = ioctl(vm_fd, KVM_CREATE_VCPU, 0);
	if (vcpu_fd < 0)
		die("KVM_CREATE_VCPU ioctl.\n");
	printf("Create vcpu.\n");
	return vcpu_fd;
}

static void *vcpu_thread(void *arg)
{
	int vm_fd = (int)(long)arg;

	create_vcpu(vm_fd);
	return NULL;
}

int main(int argc, char *argv[])
{
	pthread_t thread;
	int vm_fd;

	(void)argc;
	(void)argv;

	vm_fd = create_vm();
	pthread_create(&thread, NULL, vcpu_thread, (void *)(long)vm_fd);
	printf("Exit.\n");
	return 0;
}

It caused by release kvm->arch.ept_identity_map_addr which is the
error page.

The parent thread can send KILL signal to the vcpu thread when it was
exiting which stops faulting pages and potentially allocating memory.
So gfn_to_pfn/gfn_to_page may fail at this time

Fixed by checking the page before it is used
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>

If kernel is compiled with CONFIG_PROVE_LOCKING the
validator raises an error when a multiplexer is removed
via sysfs and sub-clients are connected to it. This is a
false positive.
Documentation/lockdep-design.txt recommends to handle this
via calls to mutex_lock_nested().

Based on an earlier fix from Michael Lawnick.

Note that the extra code resolves to nothing unless
CONFIG_DEBUG_LOCK_ALLOC=y.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Michael Lawnick <ml.lawnick@gmx.de>

This patch adds config I2C_DESIGNWARE_CORE in Kconfig, and let
I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI select I2C_DESIGNWARE_CORE.

Because both I2C_DESIGNWARE_PLATFORM and I2C_DESIGNWARE_PCI can be built as
built-in or module, we also need to export the functions in i2c-designware-core.

This fixes below build error when CONFIG_I2C_DESIGNWARE_PLATFORM=y &&
CONFIG_I2C_DESIGNWARE_PCI=y:

  LD      drivers/i2c/busses/built-in.o
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_clear_int':
i2c-designware-core.c:(.text+0xa10): multiple definition of `i2c_dw_clear_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x928): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_init':
i2c-designware-core.c:(.text+0x178): multiple definition of `i2c_dw_init'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x90): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_readl':
i2c-designware-core.c:(.text+0xe8): multiple definition of `dw_readl'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_isr':
i2c-designware-core.c:(.text+0x724): multiple definition of `i2c_dw_isr'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x63c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer':
i2c-designware-core.c:(.text+0x4b0): multiple definition of `i2c_dw_xfer'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c8): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_is_enabled':
i2c-designware-core.c:(.text+0x9d4): multiple definition of `i2c_dw_is_enabled'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8ec): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `dw_writel':
i2c-designware-core.c:(.text+0x124): multiple definition of `dw_writel'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x3c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_xfer_msg':
i2c-designware-core.c:(.text+0x2e8): multiple definition of `i2c_dw_xfer_msg'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x200): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_enable':
i2c-designware-core.c:(.text+0x9c8): multiple definition of `i2c_dw_enable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8e0): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_read_comp_param':
i2c-designware-core.c:(.text+0xa24): multiple definition of `i2c_dw_read_comp_param'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x93c): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable':
i2c-designware-core.c:(.text+0x9dc): multiple definition of `i2c_dw_disable'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x8f4): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_func':
i2c-designware-core.c:(.text+0x710): multiple definition of `i2c_dw_func'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x628): first defined here
drivers/i2c/busses/i2c-designware-pci.o: In function `i2c_dw_disable_int':
i2c-designware-core.c:(.text+0xa18): multiple definition of `i2c_dw_disable_int'
drivers/i2c/busses/i2c-designware-platform.o:i2c-designware-platdrv.c:(.text+0x930): first defined here
make[3]: *** [drivers/i2c/busses/built-in.o] Error 1
make[2]: *** [drivers/i2c/busses] Error 2
make[1]: *** [drivers/i2c] Error 2
make: *** [drivers] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Jiri Slaby <jslaby@suse.cz>
Cc: stable@vger.kernel.org [3.2+]

Add the SMBus Device IDs for the Intel Lynx Point-LP PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

Checks and operations on the INVPCID feature bit should use EBX
of CPUID leaf 7 instead of ECX.
Signed-off-by: Junjie Mao <junjie.mao@intel.com>
Signed-off-by: Yongjie Ren <yongjien.ren@intel.com>
Signed-off-by: Avi Kivity <avi@redhat.com>

Pull DMA-mapping fixes from Marek Szyprowski:
 "Another set of fixes for ARM dma-mapping subsystem.

  Commit e9da6e99 replaced custom consistent buffer remapping code
  with generic vmalloc areas.  It however introduced some regressions
  caused by limited support for allocations in atomic context.  This
  series contains fixes for those regressions.

  For some subplatforms the default, pre-allocated pool for atomic
  allocations turned out to be too small, so a function for setting its
  size has been added.

  Another set of patches adds support for atomic allocations to
  IOMMU-aware DMA-mapping implementation.

  The last part of this pull request contains two fixes for Contiguous
  Memory Allocator, which relax too strict requirements."

* 'fixes-for-3.6' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  ARM: dma-mapping: IOMMU allocates pages from atomic_pool with GFP_ATOMIC
  ARM: dma-mapping: Introduce __atomic_get_pages() for __iommu_get_pages()
  ARM: dma-mapping: Refactor out to introduce __in_atomic_pool
  ARM: dma-mapping: atomic_pool with struct page **pages
  ARM: Kirkwood: increase atomic coherent pool size
  ARM: DMA-Mapping: print warning when atomic coherent allocation fails
  ARM: DMA-Mapping: add function for setting coherent pool size from platform code
  ARM: relax conditions required for enabling Contiguous Memory Allocator
  mm: cma: fix alignment requirements for contiguous regions

Pull input subsystem updates from Dmitry Torokhov.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: wacom - add support for EMR on Cintiq 24HD touch
  Input: i8042 - add Gigabyte T1005 series netbooks to noloop table
  Input: imx_keypad - reset the hardware before enabling
  Input: edt-ft5x06 - fix build error when compiling wthout CONFIG_DEBUG_FS

Pull HID updates from Jiri Kosina:
 "It contains a fix for Eaton Ellipse MAX UPS from Alan Stern,
  performance improvement (not processing debug data if noone is
  interested), by Henrik Rydberg, and allowing tpkbd-driven devices to
  work even with generic driver in a crippled mode, by Andres Freund."

* 'upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
  HID: Only dump input if someone is listening
  HID: add NOGET quirk for Eaton Ellipse MAX UPS

c1dcad2d added a new driver configured by
HID_LENOVO_TPKBD but made the hid_have_special_driver entry non-optional which
lead to a recognized but non-working device if the new driver wasn't
configured (which is the correct default).
Signed-off-by: Andres Freund <andres@anarazel.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>

Replace blackfin ipi message queue with generic smp helper function.
Signed-off-by: Steven Miao <realmz6@gmail.com>
Signed-off-by: Bob Liu <lliubbo@gmail.com>

This will cause udev to load vmwgfx instead of waiting for X
to do it.
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

This makes things easier for distros where we'd like to have fbcon
enabled all the time.
Signed-off-by: Dave Airlie <airlied@redhat.com>

Merge tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
 * Fix for TLB flushing introduced in v3.6
 * Fix Xen-SWIOTLB not using proper DMA mask - device had 64bit but
   in a 32-bit kernel we need to allocate for coherent pages from a
   32-bit pool.
 * When trying to re-use P2M nodes we had a one-off error and triggered
   a BUG_ON check with specific CONFIG_ option.
 * When doing FLR in Xen-PCI-backend we would first do FLR then save the
   PCI configuration space. We needed to do it the other way around.

* tag 'stable/for-linus-3.6-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/pciback: Fix proper FLR steps.
  xen: Use correct masking in xen_swiotlb_alloc_coherent.
  xen: fix logical error in tlb flushing
  xen/p2m: Fix one-off error in checking the P2M tree directory.

Pull PCI updates from Bjorn Helgaas:
 "Power management
    - PCI/PM: Enable D3/D3cold by default for most devices
    - PCI/PM: Keep parent bridge active when probing device
    - PCI/PM: Fix config reg access for D3cold and bridge suspending
    - PCI/PM: Add ABI document for sysfs file d3cold_allowed
  Core
    - PCI: Don't print anything while decoding is disabled"

* tag '3.6-pci-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: Don't print anything while decoding is disabled
  PCI/PM: Add ABI document for sysfs file d3cold_allowed
  PCI/PM: Fix config reg access for D3cold and bridge suspending
  PCI/PM: Keep parent bridge active when probing device
  PCI/PM: Enable D3/D3cold by default for most devices

In 3.6-rc3, without this patch, the following error occurs with a modular build:

ERROR: "gen_split_key" [drivers/crypto/caam/caamhash.ko] undefined!
ERROR: "gen_split_key" [drivers/crypto/caam/caamalg.ko] undefined!
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Yuan Kang <Yuan.Kang@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: Pavel Shilovsky <pshilovsky@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>

Cc: <stable@vger.kernel.org>
Signed-off-by: Pavel Shilovsky <pshilovsky@etersoft.ru>
Signed-off-by: Steve French <smfrench@gmail.com>

Pull ARM SoC bug fixes from Olof Johansson:
 "Mostly Renesas and Atmel bugfixes this time, targeting boot and build
  problems.  A couple of patches for gemini and kirkwood as well.  On a
  whole nothing very controversial."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: gemini: fix the gemini build
  ARM: shmobile: armadillo800eva: enable rw rootfs mount
  ARM: Kirkwood: Fix 'SZ_1M' undeclared here for db88f6281-bp-setup.c
  ARM: shmobile: mackerel: fixup usb module order
  ARM: shmobile: armadillo800eva: fixup: sound card detection order
  ARM: shmobile: marzen: fixup smsc911x id for regulator
  ARM: at91/feature-removal-schedule: delay at91_mci removal
  ARM: mach-shmobile: armadillo800eva: Enable power button as wakeup source
  ARM: mach-shmobile: armadillo800eva: Fix GPIO buttons descriptions
  ARM: at91/dts: remove partial parameter in at91sam9g25ek.dts
  ARM: at91/clock: fix PLLA overclock warning
  ARM: at91: fix rtc-at91sam9 irq issue due to sparse irq support
  ARM: at91: fix system timer irq issue due to sparse irq support
  ARM: shmobile: sh73a0: fixup RELOC_BASE of intca_irq_pins_desc

Pull a hwmon fix from Guenter Roeck:
 "One patch, fixing DIV_ROUND_CLOSEST to support negative dividends.

  While the changes are not in the drivers/hwmon directory, the problem
  primarily affects hwmon drivers, and it makes sense to push the patch
  through the hwmon tree."

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  linux/kernel.h: Fix DIV_ROUND_CLOSEST to support negative dividends

Pull kbuild fixes from Michal Marek:
 "These are two fixes that should go into 3.6.  The link-vmlinux.sh one
  is obvious.

  The other one fixes make firmware_install with certain configurations,
  where a file in the toplevel firmware tree gets installed first, and
  $(INSTALL_FW_PATH)/$$(dir <file>) results in /lib/firmware/./, which
  confuses make 3.82 for some reason."

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  firmware: fix directory creation rule matching with make 3.82
  link-vmlinux.sh: Fix stray "echo" in error message

Trivially triggerable, found by trinity:

  kernel BUG at mm/mempolicy.c:2546!
  Process trinity-child2 (pid: 23988, threadinfo ffff88010197e000, task ffff88007821a670)
  Call Trace:
    show_numa_map+0xd5/0x450
    show_pid_numa_map+0x13/0x20
    traverse+0xf2/0x230
    seq_read+0x34b/0x3e0
    vfs_read+0xac/0x180
    sys_pread64+0xa2/0xc0
    system_call_fastpath+0x1a/0x1f
  RIP: mpol_to_str+0x156/0x360

Cc: stable@vger.kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>