Add Keystone platform USB PHY driver support. Current main purpose
of this driver is to enable the PHY reference clock gate on the
Keystone SoC. Otherwise it is a nop PHY.

[ balbi@ti.com : add COMPILE_TEST as a possible dependency
	make sure drvdata is initialized before adding PHY ]

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add Keystone platform specific glue layer to support
USB3 Host mode.

[ balbi@ti.com : fix order of clk_disable() and
	platform_device_unregister() ]

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

DWC3 requires epout to have buffer size aligned to MaxPacketSize value.
This patch sets necessary quirk for it.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Check gadget.quirk_ep_out_aligned_size to decide if buffer size requires
to be aligned to maxpacketsize of an out endpoint.  ffs_epfile_io() needs
to pad epout buffer to match above condition if quirk is found.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

When endpoint changes (due to it being disabled or alt setting changed),
mimic the action as if the change happened after the request has been
queued, instead of retrying with the new endpoint.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Due to USB controllers may have different restrictions, usb gadget layer
needs to provide a generic way to inform gadget functions to complain
with non-standard requirements.

This patch adds 'quirk_ep_out_aligned_size' field to struct usb_gadget
to inform when controller's epout requires buffer size to be aligned to
MaxPacketSize. A helper is also provided to align buffer size when
necessary.

Cc: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch moves all bitflags to the end of usb_gadget struct in order
to improve readability.
Signed-off-by: David Cohen <david.a.cohen@linux.intel.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Use usb_add_phy_dev instead of usb_add_phy, so that devices can
be bound to the phy. This is needed to set up USB phy for
some internal PCI USB host controllers on R-Car Gen2.
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

the lock was only taken inside the hardirq
handler, which runs with IRQs disabled. There's
no chance of any race condition happening, even
on SMP machines. It's safe to remove that
spinlock.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add Tahvo USB transceiver driver.

Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Transceivers need to manage OTG controller state on OMAP1 to enable
switching between peripheral and host modes. Provide a driver for that.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add extcon field to platform data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Move omap_usb_config to platform data, so that OTG driver can include it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Don't use DEFINE_PCI_DEVICE_TABLE macro, because this macro
is not preferred.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add support for using the sourcesink function in gadgets composed with
configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Add support for using the loopback USB function in gadgets composed with
configfs.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

alloc_ep_req() is a function repeated in several modules.
Make a common implementation and use it.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

If there are setup requests not directed to an endpont or an interface,
current config's setup() has been attempted so far.
This patch, in case the above fails, adds code which tries the setup() of
configuration's function if there is only one function in the configuration.

This behavior is required to provide equivalent of gadget zero with configfs.

The gadget zero has a "config driver" for sourcesink, but all it does is
delegating the request to the function proper. So when the equivalent gadget
is set up with configfs it needs to handle requests directed to
"config driver", but with configfs it is not possible to specify
"config drivers".
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Only start the otg_timer in dual role mode; otherwise in peripheral mode
when musb is disconnected from the host port, otg_timer starts and
continuously toggles the session, which causes VBUS pulse.
Signed-off-by: Bin Liu <b-liu@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

This patch removes dependency on Freescale USB UTG Transceiver
driver and makes OTG FSM implementation selectable.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Other USB drivers may want to use OTG final state machine
implementation, so make this header available for them.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

OTG Final State Machine calls functions which may sleep.

For example, start_gadget callback implementation can use
usb_gadget_vbus_connect(), whose context: can sleep.

If so, mutex should be used instead of spinlock.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

if this header is included twice, we would have
redefinition build errors. Fix this.
Signed-off-by: Anton Tikhomirov <av.tikhomirov@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

this header uses spinlocks and errno values, so
we must include <linux/spinlock.h> and <linux/errno.h>
to avoid build errors.
Signed-off-by: Felipe Balbi <balbi@ti.com>

These functions used to return negative errror codes but now they return
ERR_PTRs.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>

device_driver.name is "const char *"
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>

The stop_activity function never uses driver argument (even
though it modifies it) and thus it is safe to remove it.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

we have a helper to fetch endpoint type out of
a descriptor, let's use it.
Signed-off-by: Felipe Balbi <balbi@ti.com>

The dsps platform needs to save save some registers at suspend time and
restore them after resume. This patch adds a struct for these registers,
and also lets the musb core know that the core registers need to be
saved as well.

We also have to explicitly de-assert the port reset upon resume on this
platform, but musb_port_reset() should not be called from glue layers.

Hence, introduce a flag in struct musb_hdrc_config for this.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

rx_mode and tx_mode need to be read at suspend time and restored on
resume for dsps platforms. So add it to the wrapper struct first, and
initialize the values.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Make musb_port_suspend() externally available, and call it when to host
goes into suspend. This allows the core to go into suspend while a
device is connected.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

It appears not all platforms featuring a musb core need to save the musb
core registers at suspend time and restore them on resume.

The dsps platform does, however, and because it shouldn't cause any
trouble on other platforms, do it unconditionally for all of them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>

Due to inter dependencies of I2C and extcon by the time dwc3
checks for extcon device its not registered especially in case of J6.
In O5 the vbus regulator save us from getting to this point.
So for tiime being return PROBE_DEFER if extcon is enabled in dt.
Signed-off-by: George Cherian <george.cherian@ti.com>

This will tell glue layer which mode we want port
to be in.
Signed-off-by: Felipe Balbi <balbi@ti.com>

this will let us support broken designs such
as AM335x EVM SK where ID pin isn't routed
anywhere on a host port.

With this we can toggle internal IDDIG signal
and make sure MUSB goes into host mode as
necessary.
Signed-off-by: Felipe Balbi <balbi@ti.com>

Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.

Cc: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>