sctp: set the value of flowi6_oif to sk_bound_dev_if to make sctp_v6_get_dst to find the correct route entry.

if there are several same route entries with different outgoing net device,
application's socket specifies the oif through setsockopt with
SO_BINDTODEVICE, sctpv6 should choose the route entry whose outgoing net
device is the oif which was specified by socket, set the value of
flowi6_oif to sk->sk_bound_dev_if to make sctp_v6_get_dst to find the
correct route entry.
Signed-off-by: Zheng Li <james.z.li@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

copy_to_user() copies the struct the pointer is pointing to, but the
length check compares against sizeof(pointer) and not sizeof(struct).
On 32-bit the size is probably the same, so it might have worked
accidentally.
Signed-off-by: Matthias Rosenfelder <mrosenfelder.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes: 6797318e ("tcp: md5: add an address prefix for key lookup")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Lennert reported a failure to add different mpls encaps in a multipath
route:

  $ ip -6 route add 1234::/16 \
        nexthop encap mpls 10 via fe80::1 dev ens3 \
        nexthop encap mpls 20 via fe80::1 dev ens3
  RTNETLINK answers: File exists

The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.

Fixes: 19e42e45 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The code that detects a failed soft reset of Octeon is comparing the wrong
value against the reset value of the Octeon SLI_SCRATCH_1 register,
resulting in an inability to detect a soft reset failure.  Fix it by using
the correct value in the comparison, which is any non-zero value.

Fixes: f21fb3ed ("Add support of Cavium Liquidio ethernet adapters")
Fixes: c0eab5b3 ("liquidio: CN23XX firmware download")
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull another parisc update from Helge Deller:
 "Christoph Hellwig provided one patch for the parisc architecture to
  drop the DMA_ERROR_CODE define from the parisc architecture"

* 'parisc-4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: ->mapping_error

Pull arm64 updates from Will Deacon:

 - RAS reporting via GHES/APEI (ACPI)

 - Indirect ftrace trampolines for modules

 - Improvements to kernel fault reporting

 - Page poisoning

 - Sigframe cleanups and preparation for SVE context

 - Core dump fixes

 - Sparse fixes (mainly relating to endianness)

 - xgene SoC PMU v3 driver

 - Misc cleanups and non-critical fixes

* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (75 commits)
  arm64: fix endianness annotation for 'struct jit_ctx' and friends
  arm64: cpuinfo: constify attribute_group structures.
  arm64: ptrace: Fix incorrect get_user() use in compat_vfp_set()
  arm64: ptrace: Remove redundant overrun check from compat_vfp_set()
  arm64: ptrace: Avoid setting compat FP[SC]R to garbage if get_user fails
  arm64: fix endianness annotation for __apply_alternatives()/get_alt_insn()
  arm64: fix endianness annotation in get_kaslr_seed()
  arm64: add missing conversion to __wsum in ip_fast_csum()
  arm64: fix endianness annotation in acpi_parking_protocol.c
  arm64: use readq() instead of readl() to read 64bit entry_point
  arm64: fix endianness annotation for reloc_insn_movw() & reloc_insn_imm()
  arm64: fix endianness annotation for aarch64_insn_write()
  arm64: fix endianness annotation in aarch64_insn_read()
  arm64: fix endianness annotation in call_undef_hook()
  arm64: fix endianness annotation for debug-monitors.c
  ras: mark stub functions as 'inline'
  arm64: pass endianness info to sparse
  arm64: ftrace: fix !CONFIG_ARM64_MODULE_PLTS kernels
  arm64: signal: Allow expansion of the signal frame
  acpi: apei: check for pending errors when probing GHES entries
  ...

Pull mnt namespace updates from Eric Biederman:
 "A big break-through came during this development cycle as a way was
  found to maintain the existing umount -l semantics while allowing for
  optimizations that improve the performance. That is represented by the
  first change in this series moving the reparenting of mounts into
  their own pass. This has allowed addressing the horrific performance
  of umount -l on a carefully crafted tree of mounts with locks held
  (0.06s vs 60s in my testing). What allowed this was not changing where
  umounts propagate to while propgating umounts.

  The next change fixes the case where the order of the mount whose
  umount are being progated visits a tree where the mounts are stacked
  upon each other in another order. This is weird but not hard to
  implement.

  The final change takes advantage of the unchanging mount propgation
  tree to skip parts of the mount propgation tree that have already been
  visited. Yielding a very nice speed up in the worst case.

  There remains one outstanding question about the semantics of umount -l
  that I am still discussiong with Ram Pai. In practice that area of the
  semantics was changed by 1064f874 ("mnt: Tuck mounts under others
  instead of creating shadow/side mounts.") and no regressions have been
  reported. Still I intend to finish talking that out with him to ensure
  there is not something a more intense use of mount propagation in the
  future will not cause to become significant"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
  mnt: Make propagate_umount less slow for overlapping mount propagation trees
  mnt: In propgate_umount handle visiting mounts in any order
  mnt: In umount propagation reparent in a separate pass

Pull GFS2 updates from Bob Peterson:
 "We've got eight GFS2 patches for this merge window:

   - Andreas Gruenbacher has four patches related to cleaning up the
     GFS2 inode evict process. This is about half of his patches
     designed to fix a long-standing GFS2 hang related to the inode
     shrinker: Shrinker calls gfs2 evict, evict calls DLM, DLM requires
     memory and blocks on the shrinker.

     These four patches have been well tested. His second set of patches
     are still being tested, so I plan to hold them until the next merge
     window, after we have more weeks of testing. The first patch
     eliminates the flush_delayed_work, which can block.

   - Andreas's second patch protects setting of gl_object for rgrps with
     a spin_lock to prevent proven races.

   - His third patch introduces a centralized mechanism for queueing
     glock work with better reference counting, to prevent more races.

    -His fourth patch retains a reference to inode glocks when an error
     occurs while creating an inode. This keeps the subsequent evict
     from needing to reacquire the glock, which might call into DLM and
     block in low memory conditions.

   - Arvind Yadav has a patch to add const to attribute_group
     structures.

   - I have a patch to detect directory entry inconsistencies and
     withdraw the file system if any are found. Better that than silent
     corruption.

   - I have a patch to remove a vestigial variable from glock
     structures, saving some slab space.

   - I have another patch to remove a vestigial variable from the GFS2
     in-core superblock structure"

* tag 'gfs2-4.13.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/gfs2/linux-gfs2:
  GFS2: constify attribute_group structures.
  gfs2: gfs2_create_inode: Keep glock across iput
  gfs2: Clean up glock work enqueuing
  gfs2: Protect gl->gl_object by spin lock
  gfs2: Get rid of flush_delayed_work in gfs2_evict_inode
  GFS2: Eliminate vestigial sd_log_flush_wrapped
  GFS2: Remove gl_list from glock structure
  GFS2: Withdraw when directory entry inconsistencies are detected

Pull btrfs updates from David Sterba:
 "The core updates improve error handling (mostly related to bios), with
  the usual incremental work on the GFP_NOFS (mis)use removal,
  refactoring or cleanups. Except the two top patches, all have been in
  for-next for an extensive amount of time.

  User visible changes:

   - statx support

   - quota override tunable

   - improved compression thresholds

   - obsoleted mount option alloc_start

  Core updates:

   - bio-related updates:
       - faster bio cloning
       - no allocation failures
       - preallocated flush bios

   - more kvzalloc use, memalloc_nofs protections, GFP_NOFS updates

   - prep work for btree_inode removal

   - dir-item validation

   - qgoup fixes and updates

   - cleanups:
       - removed unused struct members, unused code, refactoring
       - argument refactoring (fs_info/root, caller -> callee sink)
       - SEARCH_TREE ioctl docs"

* 'for-4.13-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: (115 commits)
  btrfs: Remove false alert when fiemap range is smaller than on-disk extent
  btrfs: Don't clear SGID when inheriting ACLs
  btrfs: fix integer overflow in calc_reclaim_items_nr
  btrfs: scrub: fix target device intialization while setting up scrub context
  btrfs: qgroup: Fix qgroup reserved space underflow by only freeing reserved ranges
  btrfs: qgroup: Introduce extent changeset for qgroup reserve functions
  btrfs: qgroup: Fix qgroup reserved space underflow caused by buffered write and quotas being enabled
  btrfs: qgroup: Return actually freed bytes for qgroup release or free data
  btrfs: qgroup: Cleanup btrfs_qgroup_prepare_account_extents function
  btrfs: qgroup: Add quick exit for non-fs extents
  Btrfs: rework delayed ref total_bytes_pinned accounting
  Btrfs: return old and new total ref mods when adding delayed refs
  Btrfs: always account pinned bytes when dropping a tree block ref
  Btrfs: update total_bytes_pinned when pinning down extents
  Btrfs: make BUG_ON() in add_pinned_bytes() an ASSERT()
  Btrfs: make add_pinned_bytes() take an s64 num_bytes instead of u64
  btrfs: fix validation of XATTR_ITEM dir items
  btrfs: Verify dir_item in iterate_object_props
  btrfs: Check name_len before in btrfs_del_root_ref
  btrfs: Check name_len before reading btrfs_get_name
  ...

Pull memdup_user() conversions from Al Viro:
 "A fairly self-contained series - hunting down open-coded memdup_user()
  and memdup_user_nul() instances"

* 'work.memdup_user' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  bpf: don't open-code memdup_user()
  kimage_file_prepare_segments(): don't open-code memdup_user()
  ethtool: don't open-code memdup_user()
  do_ip_setsockopt(): don't open-code memdup_user()
  do_ipv6_setsockopt(): don't open-code memdup_user()
  irda: don't open-code memdup_user()
  xfrm_user_policy(): don't open-code memdup_user()
  ima_write_policy(): don't open-code memdup_user_nul()
  sel_write_validatetrans(): don't open-code memdup_user_nul()

Pull timer-related user access updates from Al Viro:
 "Continuation of timers-related stuff (there had been more, but my
  parts of that series are already merged via timers/core). This is more
  of y2038 work by Deepa Dinamani, partially disrupted by the
  unification of native and compat timers-related syscalls"

* 'timers-compat' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  posix_clocks: Use get_itimerspec64() and put_itimerspec64()
  timerfd: Use get_itimerspec64() and put_itimerspec64()
  nanosleep: Use get_timespec64() and put_timespec64()
  posix-timers: Use get_timespec64() and put_timespec64()
  posix-stubs: Conditionally include COMPAT_SYS_NI defines
  time: introduce {get,put}_itimerspec64
  time: add get_timespec64 and put_timespec64

Pull read/write updates from Al Viro:
 "Christoph's fs/read_write.c series - consolidation and cleanups"

* 'work.read_write' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  nfsd: remove nfsd_vfs_read
  nfsd: use vfs_iter_read/write
  fs: implement vfs_iter_write using do_iter_write
  fs: implement vfs_iter_read using do_iter_read
  fs: move more code into do_iter_read/do_iter_write
  fs: remove __do_readv_writev
  fs: remove do_compat_readv_writev
  fs: remove do_readv_writev

Pull wait syscall updates from Al Viro:
 "Consolidating sys_wait* and compat counterparts.

  Gets rid of set_fs()/double-copy mess, simplifies the whole thing
  (lifting the copyouts to the syscalls means less headache in the part
  that does actual work - fewer failure exits, to start with), gets rid
  of the overhead of field-by-field __put_user()"

* 'work.sys_wait' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  osf_wait4: switch to kernel_wait4()
  waitid(): switch copyout of siginfo to unsafe_put_user()
  wait_task_zombie: consolidate info logics
  kill wait_noreap_copyout()
  lift getrusage() from wait_noreap_copyout()
  waitid(2): leave copyout of siginfo to syscall itself
  kernel_wait4()/kernel_waitid(): delay copying status to userland
  wait4(2)/waitid(2): separate copying rusage to userland
  move compat wait4 and waitid next to native variants

Pull misc user access cleanups from Al Viro:
 "The first pile is assorted getting rid of cargo-culted access_ok(),
  cargo-culted set_fs() and field-by-field copyouts.

  The same description applies to a lot of stuff in other branches -
  this is just the stuff that didn't fit into a more specific topical
  branch"

* 'work.misc-set_fs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  Switch flock copyin/copyout primitives to copy_{from,to}_user()
  fs/fcntl: return -ESRCH in f_setown when pid/pgid can't be found
  fs/fcntl: f_setown, avoid undefined behaviour
  fs/fcntl: f_setown, allow returning error
  lpfc debugfs: get rid of pointless access_ok()
  adb: get rid of pointless access_ok()
  isdn: get rid of pointless access_ok()
  compat statfs: switch to copy_to_user()
  fs/locks: don't mess with the address limit in compat_fcntl64
  nfsd_readlink(): switch to vfs_get_link()
  drbd: ->sendpage() never needed set_fs()
  fs/locks: pass kernel struct flock to fcntl_getlk/setlk
  fs: locks: Fix some troubles at kernel-doc comments

Every developer always thinks that _their_ code is so special and
magical that it should be enabled by default.

And most of them are completely and utterly wrong.  That's definitely
the case when you write a specialty driver for a very unsual "security
processor". It does *not* get to mark itself as "default m".

If you solve world hunger, and make a driver that cures people of
cancer, by all means enable it by default.  But afaik, the Cavium
CNN55XX does neither.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

DMA_ERROR_CODE already went away in linux-next, but parisc unfortunately
added a new instance of it without any review as far as I can tell.

Move the two iommu drivers to report errors through ->mapping_error.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Helge Deller <deller@gmx.de>

Pull networking updates from David Miller:
 "Reasonably busy this cycle, but perhaps not as busy as in the 4.12
  merge window:

   1) Several optimizations for UDP processing under high load from
      Paolo Abeni.

   2) Support pacing internally in TCP when using the sch_fq packet
      scheduler for this is not practical. From Eric Dumazet.

   3) Support mutliple filter chains per qdisc, from Jiri Pirko.

   4) Move to 1ms TCP timestamp clock, from Eric Dumazet.

   5) Add batch dequeueing to vhost_net, from Jason Wang.

   6) Flesh out more completely SCTP checksum offload support, from
      Davide Caratti.

   7) More plumbing of extended netlink ACKs, from David Ahern, Pablo
      Neira Ayuso, and Matthias Schiffer.

   8) Add devlink support to nfp driver, from Simon Horman.

   9) Add RTM_F_FIB_MATCH flag to RTM_GETROUTE queries, from Roopa
      Prabhu.

  10) Add stack depth tracking to BPF verifier and use this information
      in the various eBPF JITs. From Alexei Starovoitov.

  11) Support XDP on qed device VFs, from Yuval Mintz.

  12) Introduce BPF PROG ID for better introspection of installed BPF
      programs. From Martin KaFai Lau.

  13) Add bpf_set_hash helper for TC bpf programs, from Daniel Borkmann.

  14) For loads, allow narrower accesses in bpf verifier checking, from
      Yonghong Song.

  15) Support MIPS in the BPF selftests and samples infrastructure, the
      MIPS eBPF JIT will be merged in via the MIPS GIT tree. From David
      Daney.

  16) Support kernel based TLS, from Dave Watson and others.

  17) Remove completely DST garbage collection, from Wei Wang.

  18) Allow installing TCP MD5 rules using prefixes, from Ivan
      Delalande.

  19) Add XDP support to Intel i40e driver, from Björn Töpel

  20) Add support for TC flower offload in nfp driver, from Simon
      Horman, Pieter Jansen van Vuuren, Benjamin LaHaise, Jakub
      Kicinski, and Bert van Leeuwen.

  21) IPSEC offloading support in mlx5, from Ilan Tayari.

  22) Add HW PTP support to macb driver, from Rafal Ozieblo.

  23) Networking refcount_t conversions, From Elena Reshetova.

  24) Add sock_ops support to BPF, from Lawrence Brako. This is useful
      for tuning the TCP sockopt settings of a group of applications,
      currently via CGROUPs"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1899 commits)
  net: phy: dp83867: add workaround for incorrect RX_CTRL pin strap
  dt-bindings: phy: dp83867: provide a workaround for incorrect RX_CTRL pin strap
  cxgb4: Support for get_ts_info ethtool method
  cxgb4: Add PTP Hardware Clock (PHC) support
  cxgb4: time stamping interface for PTP
  nfp: default to chained metadata prepend format
  nfp: remove legacy MAC address lookup
  nfp: improve order of interfaces in breakout mode
  net: macb: remove extraneous return when MACB_EXT_DESC is defined
  bpf: add missing break in for the TCP_BPF_SNDCWND_CLAMP case
  bpf: fix return in load_bpf_file
  mpls: fix rtm policy in mpls_getroute
  net, ax25: convert ax25_cb.refcount from atomic_t to refcount_t
  net, ax25: convert ax25_route.refcount from atomic_t to refcount_t
  net, ax25: convert ax25_uid_assoc.refcount from atomic_t to refcount_t
  net, sctp: convert sctp_ep_common.refcnt from atomic_t to refcount_t
  net, sctp: convert sctp_transport.refcnt from atomic_t to refcount_t
  net, sctp: convert sctp_chunk.refcnt from atomic_t to refcount_t
  net, sctp: convert sctp_datamsg.refcnt from atomic_t to refcount_t
  net, sctp: convert sctp_auth_bytes.refcnt from atomic_t to refcount_t
  ...

Pull crypto updates from Herbert Xu:
 "Algorithms:
   - add private key generation to ecdh

  Drivers:
   - add generic gcm(aes) to aesni-intel
   - add SafeXcel EIP197 crypto engine driver
   - add ecb(aes), cfb(aes) and ecb(des3_ede) to cavium
   - add support for CNN55XX adapters in cavium
   - add ctr mode to chcr
   - add support for gcm(aes) to omap"

* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (140 commits)
  crypto: testmgr - Reenable sha1/aes in FIPS mode
  crypto: ccp - Release locks before returning
  crypto: cavium/nitrox - dma_mapping_error() returns bool
  crypto: doc - fix typo in docs
  Documentation/bindings: Document the SafeXel cryptographic engine driver
  crypto: caam - fix gfp allocation flags (part II)
  crypto: caam - fix gfp allocation flags (part I)
  crypto: drbg - Fixes panic in wait_for_completion call
  crypto: caam - make of_device_ids const.
  crypto: vmx - remove unnecessary check
  crypto: n2 - make of_device_ids const
  crypto: inside-secure - use the base_end pointer in ring rollback
  crypto: inside-secure - increase the batch size
  crypto: inside-secure - only dequeue when needed
  crypto: inside-secure - get the backlog before dequeueing the request
  crypto: inside-secure - stop requeueing failed requests
  crypto: inside-secure - use one queue per hw ring
  crypto: inside-secure - update the context and request later
  crypto: inside-secure - align the cipher and hash send functions
  crypto: inside-secure - optimize DSE bufferability control
  ...

Pull GCC plugin updates from Kees Cook:
 "The big part is the randstruct plugin infrastructure.

  This is the first of two expected pull requests for randstruct since
  there are dependencies in other trees that would be easier to merge
  once those have landed. Notably, the IPC allocation refactoring in
  -mm, and many trivial merge conflicts across several trees when
  applying the __randomize_layout annotation.

  As a result, it seemed like I should send this now since it is
  relatively self-contained, and once the rest of the trees have landed,
  send the annotation patches. I'm expecting the final phase of
  randstruct (automatic struct selection) will land for v4.14, but if
  its other tree dependencies actually make it for v4.13, I can send
  that merge request too.

  Summary:

  - typo fix in Kconfig (Jean Delvare)

  - randstruct infrastructure"

* tag 'gcc-plugins-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  ARM: Prepare for randomized task_struct
  randstruct: Whitelist NIU struct page overloading
  randstruct: Whitelist big_key path struct overloading
  randstruct: Whitelist UNIXCB cast
  randstruct: Whitelist struct security_hook_heads cast
  gcc-plugins: Add the randstruct plugin
  Fix English in description of GCC_PLUGIN_STRUCTLEAK
  compiler: Add __designated_init annotation
  gcc-plugins: Detail c-common.h location for GCC 4.6

Pull pstore updates from Kees Cook:
 "Various fixes and tweaks for the pstore subsystem.

  Highlights:

   - use memdup_user() instead of open-coded copies (Geliang Tang)

   - fix record memory leak during initialization (Douglas Anderson)

   - avoid confused compressed record warning (Ankit Kumar)

   - prepopulate record timestamp and remove redundant logic from
     backends"

* tag 'pstore-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
  powerpc/nvram: use memdup_user
  pstore: use memdup_user
  pstore: Fix format string to use %u for record id
  pstore: Populate pstore record->time field
  pstore: Create common record initializer
  efi-pstore: Refactor erase routine
  pstore: Avoid potential infinite loop
  pstore: Fix leaked pstore_record in pstore_get_backend_records()
  pstore: Don't warn if data is uncompressed and type is not PSTORE_TYPE_DMESG

Pull security layer updates from James Morris:

 - a major update for AppArmor. From JJ:

     * several bug fixes and cleanups

     * the patch to add symlink support to securityfs that was floated
       on the list earlier and the apparmorfs changes that make use of
       securityfs symlinks

     * it introduces the domain labeling base code that Ubuntu has been
       carrying for several years, with several cleanups applied. And it
       converts the current mediation over to using the domain labeling
       base, which brings domain stacking support with it. This finally
       will bring the base upstream code in line with Ubuntu and provide
       a base to upstream the new feature work that Ubuntu carries.

     * This does _not_ contain any of the newer apparmor mediation
       features/controls (mount, signals, network, keys, ...) that
       Ubuntu is currently carrying, all of which will be RFC'd on top
       of this.

 - Notable also is the Infiniband work in SELinux, and the new file:map
   permission. From Paul:

      "While we're down to 21 patches for v4.13 (it was 31 for v4.12),
       the diffstat jumps up tremendously with over 2k of line changes.

       Almost all of these changes are the SELinux/IB work done by
       Daniel Jurgens; some other noteworthy changes include a NFS v4.2
       labeling fix, a new file:map permission, and reporting of policy
       capabilities on policy load"

   There's also now genfscon labeling support for tracefs, which was
   lost in v4.1 with the separation from debugfs.

 - Smack incorporates a safer socket check in file_receive, and adds a
   cap_capable call in privilege check.

 - TPM as usual has a bunch of fixes and enhancements.

 - Multiple calls to security_add_hooks() can now be made for the same
   LSM, to allow LSMs to have hook declarations across multiple files.

 - IMA now supports different "ima_appraise=" modes (eg. log, fix) from
   the boot command line.

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security: (126 commits)
  apparmor: put back designators in struct initialisers
  seccomp: Switch from atomic_t to recount_t
  seccomp: Adjust selftests to avoid double-join
  seccomp: Clean up core dump logic
  IMA: update IMA policy documentation to include pcr= option
  ima: Log the same audit cause whenever a file has no signature
  ima: Simplify policy_func_show.
  integrity: Small code improvements
  ima: fix get_binary_runtime_size()
  ima: use ima_parse_buf() to parse template data
  ima: use ima_parse_buf() to parse measurements headers
  ima: introduce ima_parse_buf()
  ima: Add cgroups2 to the defaults list
  ima: use memdup_user_nul
  ima: fix up #endif comments
  IMA: Correct Kconfig dependencies for hash selection
  ima: define is_ima_appraise_enabled()
  ima: define Kconfig IMA_APPRAISE_BOOTPARAM option
  ima: define a set of appraisal rules requiring file signatures
  ima: extend the "ima_policy" boot command line to support multiple policies
  ...

Pull audit updates from Paul Moore:
 "Things are relatively quiet on the audit front for v4.13, just five
  patches for a total diffstat of 102 lines.

  There are two patches from Richard to consistently record the POSIX
  capabilities and add the ambient capability information as well.

  I also chipped in two patches to fix a race condition with the auditd
  tracking code and ensure we don't skip sending any records to the
  audit multicast group.

  Finally a single style fix that I accepted because I must have been in
  a good mood that day.

  Everything passes our test suite, and should be relatively harmless,
  please merge for v4.13"

* 'stable-4.13' of git://git.infradead.org/users/pcmoore/audit:
  audit: make sure we never skip the multicast broadcast
  audit: fix a race condition with the auditd tracking code
  audit: style fix
  audit: add ambient capabilities to CAPSET and BPRM_FCAPS records
  audit: unswing cap_* fields in PATH records

Pull printk updates from Petr Mladek:

 - Store printk() messages into the main log buffer directly even in NMI
   when the lock is available. It is the best effort to print even large
   chunk of text. It is handy, for example, when all ftrace messages are
   printed during the system panic in NMI.

 - Add missing annotations to calm down compiler warnings

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk:
  printk: add __printf attributes to internal functions
  printk: Use the main logbuf in NMI when logbuf_lock is available

attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.

File size before:
   text	   data	    bss	    dec	    hex	filename
   5259	   1344	      8	   6611	   19d3	fs/gfs2/sys.o

File size After adding 'const':
   text	   data	    bss	    dec	    hex	filename
   5371	   1216	      8	   6595	   19c3	fs/gfs2/sys.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>

On failure, keep the inode glock across the final iput of the new inode
so that gfs2_evict_inode doesn't have to re-acquire the glock.  That
way, gfs2_evict_inode won't need to revalidate the block type.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>

This patch adds a standardized queueing mechanism for glock work
with spin_lock protection to prevent races.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>

Put all remaining accesses to gl->gl_object under the
gl->gl_lockref.lock spinlock to prevent races.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>

So far, gfs2_evict_inode clears gl->gl_object and then flushes the glock
work queue to make sure that inode glops which dereference gl->gl_object
have finished running before the inode is destroyed.  However, flushing
the work queue may do more work than needed, and in particular, it may
call into DLM, which we want to avoid here.  Use a bit lock
(GIF_GLOP_PENDING) to synchronize between the inode glops and
gfs2_evict_inode instead to get rid of the flushing.

In addition, flush the work queues of existing glocks before reusing
them for new inodes to get those glocks into a known state: the glock
state engine currently doesn't handle glock re-appropriation correctly.
(We may be able to fix the glock state engine instead later.)

Based on a patch by Steven Whitehouse <swhiteho@redhat.com>.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Bob Peterson <rpeterso@redhat.com>

Sekhar Nori says:

====================
net: phy: dp83867: workaround incorrect RX_CTRL pin strap

This patch series adds workaround for incorrect RX_CTRL pin strap
setting that can be found on some TI boards.

This is required to be complaint to PHY datamanual specification.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).

There are some boards which have the pin strapped this way and need
software workaround suggested by the data manual. Bit[7] of
Configuration Register 4 (address 0x0031) must be cleared to 0. This
ensures proper operation of the PHY.

Implement driver support for device-tree property meant to advertise
the wrong strapping.

[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdfSigned-off-by: Murali Karicheri <m-karicheri2@ti.com>
[nsekhar@ti.com: rebase to mainline, code simplification]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).

It further advises that if a board has this pin strapped in mode 1 and
mode 2, then to ensure proper operation of the PHY, a software workaround
must be implemented.

Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property for the board to
advertise this and allow corrective action in software.

[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdfSigned-off-by: Murali Karicheri <m-karicheri2@ti.com>
[nsekhar@ti.com: rebase to mainline, split documentation into separate patch]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Atul Gupta says:

====================
cxgb4: Add PTP Hardware Clock (PHC) support

V4:
	Splitting the patch again
V3:
        Releasing lock in the exit paths
V2:
        Splitting the patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add PTP IEEE-1588 support and make it accessible via PHC subsystem.
The functionality is enabled for T5/T6 adapters. Driver interfaces with
Firmware to program and adjust the clock offset.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Supports hardware and software time stamping via the
Linux SO_TIMESTAMPING socket option.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: port enumeration change and FW ABI adjustment

This set changes the way ports are numbered internally to avoid MAC address
changes and invalid link information when breakout is configured.  Second
patch gets rid of old way of looking up MAC addresses in device information
which caused all this confusion.

Patch 3 is a small adjustment to the new FW ABI version we introduced in
this release cycle.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

ABI 4.x introduced the chained metadata format and made it the
only one possible.  There are cases, however, where the old
format is preferred - mostly to make interoperation with VFs
using ABI 3.x easier for the datapath.  In ABI 5.x we allowed
for more flexibility by selecting the metadata format based
on capabilities.  The default was left to non-chained.

In case of fallback traffic, there is no capability telling the
driver there may be chained metadata.  With a very stripped-
-down FW the default old metadata format would be selected
making the driver drop all fallback traffic.

This patch changes the default selection in the driver. It
should not hurt with old firmwares, because if they don't
advertise RSS they will not produce metadata anyway.  New
firmwares advertising ABI 5.x, however, can depend on the
driver defaulting to chained format.

Fixes: f9380629 ("nfp: advertise support for NFD ABI 0.5")
Suggested-by: Michael Rapson <michael.rapson@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The legacy MAC address lookup doesn't work well with breakout
cables.  We are probably better off picking random addresses
than the wrong ones in the theoretical scenario where management
FW didn't tell us what the port config is.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For historical reasons we enumerate the vNICs in order.  This means
that if user configures breakout on a multiport card, the first
interface of the second port will have its MAC address changed.

What's worse, when moved from static information (HWInfo) to using
management FW (NSP), more features started depending on the port ids.
Right now in case of breakout first subport of the second port and
second subport of the first port will have their link info swapped.

Revise the ordering scheme so that first subport maintains its address.
Side effect of this change is that we will use base lane ids in
devlink (i.e. 40G ports will be 4 ids apart), e.g.:

pci/0000:04:00.0/0: type eth netdev p6p1
pci/0000:04:00.0/4: type eth netdev p6p2

Note that behaviour of phys_port_id is not changed since there is
a separate id number for the subport there.

Fixes: ec8b1fbe ("nfp: support port splitting via devlink")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>