- 26 Feb, 2017 20 commits
-
-
Johan Hovold authored
commit a6bb1e17 upstream. FTDI devices use a receive latency timer to periodically empty the receive buffer and report modem and line status (also when the buffer is empty). When a break or error condition is detected the corresponding status flags will be set on a packet with nonzero data payload and the flags are not updated until the break is over or further characters are received. In order to avoid over-reporting break and error conditions, these flags must therefore only be processed for packets with payload. This specifically fixes the case where after an overrun, the error condition is continuously reported and NULL-characters inserted until further data is received. Reported-by:
Michael Walle <michael@walle.cc> Fixes: 72fda3ca ("USB: serial: ftd_sio: implement sysrq handling on break") Fixes: 166ceb69 ("USB: ftdi_sio: clean up line-status handling") Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Johan Hovold authored
commit c6dce262 upstream. Since commit 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag") the FTDI driver has been using a receive latency-timer value of 1 ms instead of the device default of 16 ms. The latency timer is used to periodically empty a non-full receive buffer, but a status header is always sent when the timer expires including when the buffer is empty. This means that a two-byte bulk message is received every millisecond also for an otherwise idle port as long as it is open. Let's restore the pre-2009 behaviour which reduces the rate of the status messages to 1/16th (e.g. interrupt frequency drops from 1 kHz to 62.5 Hz) by not setting ASYNC_LOW_LATENCY by default. Anyone willing to pay the price for the minimum-latency behaviour should set the flag explicitly instead using the TIOCSSERIAL ioctl or a tool such as setserial (e.g. setserial /dev/ttyUSB0 low_latency). Note that since commit 0cbd81a9 ("USB: ftdi_sio: remove tty->low_latency") the ASYNC_LOW_LATENCY flag has no other effects but to set a minimal latency timer. Reported-by:
Antoine Aubert <a.aubert@overkiz.com> Fixes: 557aaa7f ("ft232: support the ASYNC_LOW_LATENCY flag") Signed-off-by:
-
Johan Hovold authored
commit 427c3a95 upstream. Make sure to detect short responses when fetching the modem status in order to avoid parsing uninitialised buffer data and having bits of it leak to user space. Note that we still allow for short 1-byte responses. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reviewed-by:
-
Ken Lin authored
commit 9a593656 upstream. Add new USB IDs for cp2104/5 devices on Bx50v3 boards due to the design change. Signed-off-by:
Ken Lin <yungching0725@gmail.com> Signed-off-by:
-
Johan Hovold authored
commit 5182c2cf upstream. Fix another NULL-pointer dereference at open should a malicious device lack an interrupt-in endpoint. Note that the driver has a broken check for an interrupt-in endpoint which means that an interrupt URB has never even been submitted. Fixes: 3f542974 ("USB: Moschip 7840 USB-Serial Driver") Reviewed-by:
-
Javier Martinez Canillas authored
commit abe81f3b upstream. If the driver is built as a module, autoload won't work because the module alias information is not filled. So user-space can't match the registered device with the corresponding module. Export the module alias information using the MODULE_DEVICE_TABLE() macro. Before this patch: $ modinfo drivers/tty/serial/msm_serial.ko | grep alias $ After this patch: $ modinfo drivers/tty/serial/msm_serial.ko | grep alias alias: of:N*T*Cqcom,msm-uartdmC* alias: of:N*T*Cqcom,msm-uartdm alias: of:N*T*Cqcom,msm-uartC* alias: of:N*T*Cqcom,msm-uart Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Acked-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Maxime Jayat authored
[ Upstream commit e623a9e9 ] Commit 34b88a68 ("net: Fix use after free in the recvmmsg exit path"), changed the exit path of recvmmsg to always return the datagrams variable and modified the error paths to set the variable to the error code returned by recvmsg if necessary. However in the case sock_error returned an error, the error code was then ignored, and recvmmsg returned 0. Change the error path of recvmmsg to correctly return the error code of sock_error. The bug was triggered by using recvmmsg on a CAN interface which was not up. Linux 4.6 and later return 0 in this case while earlier releases returned -ENETDOWN. Fixes: 34b88a68 ("net: Fix use after free in the recvmmsg exit path") Signed-off-by:
Maxime Jayat <maxime.jayat@mobile-devices.fr> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Paolo Abeni authored
[ Upstream commit ca4ef457 ] The skbs processed by ip_cmsg_recv() are not guaranteed to be linear e.g. when sending UDP packets over loopback with MSGMORE. Using csum_partial() on [potentially] the whole skb len is dangerous; instead be on the safe side and use skb_checksum(). Thanks to syzkaller team to detect the issue and provide the reproducer. v1 -> v2: - move the variable declaration in a tighter scope Fixes: ad6f939a ("ip: Add offset parameter to ip_cmsg_recv") Reported-by:
Andrey Konovalov <andreyknvl@google.com> Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Acked-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Michael S. Tsirkin authored
[ Upstream commit e7169530 ] Resizing currently drops consumer lock. This can cause entries to be reordered, which isn't good in itself. More importantly, consumer can detect a false ring empty condition and block forever. Further, nesting of consumer within producer lock is problematic for tun, since it produces entries in a BH, which causes a lock order reversal: CPU0 CPU1 ---- ---- consume: lock(&(&r->consumer_lock)->rlock); resize: local_irq_disable(); lock(&(&r->producer_lock)->rlock); lock(&(&r->consumer_lock)->rlock); <Interrupt> produce: lock(&(&r->producer_lock)->rlock); To fix, nest producer lock within consumer lock during resize, and keep consumer lock during the whole swap operation. Reported-by:
Dmitry Vyukov <dvyukov@google.com> Cc: stable@vger.kernel.org Cc: "David S. Miller" <davem@davemloft.net> Acked-by:
Jason Wang <jasowang@redhat.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Signed-off-by:
-
David S. Miller authored
[ Upstream commit 4c03b862 ] A nested lock depth was added to the hasbin_delete() code but it doesn't actually work some well and results in tons of lockdep splats. Fix the code instead to properly drop the lock around the operation and just keep peeking the head of the hashbin queue. Reported-by:
-
Paolo Abeni authored
[ Upstream commit 22f0708a ] Since the commit 0c1d70af ("net: use dst_cache for vxlan device") vxlan_fill_metadata_dst() calls vxlan_get_route() passing a NULL dst_cache pointer, so the latter should explicitly check for valid dst_cache ptr. Unfortunately the commit d71785ff ("net: add dst_cache to ovs vxlan lwtunnel") removed said check. As a result is possible to trigger a null pointer access calling vxlan_fill_metadata_dst(), e.g. with: ovs-vsctl add-br ovs-br0 ovs-vsctl add-port ovs-br0 vxlan0 -- set interface vxlan0 \ type=vxlan options:remote_ip=192.168.1.1 \ options:key=1234 options:dst_port=4789 ofport_request=10 ip address add dev ovs-br0 172.16.1.2/24 ovs-vsctl set Bridge ovs-br0 ipfix=@i -- --id=@i create IPFIX \ targets=\"172.16.1.1:1234\" sampling=1 iperf -c 172.16.1.1 -u -l 1000 -b 10M -t 1 -p 1234 This commit addresses the issue passing to vxlan_get_route() the dst_cache already available into the lwt info processed by vxlan_fill_metadata_dst(). Fixes: d71785ff ("net: add dst_cache to ovs vxlan lwtunnel") Signed-off-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Andrey Konovalov authored
[ Upstream commit 5edabca9 ] In the current DCCP implementation an skb for a DCCP_PKT_REQUEST packet is forcibly freed via __kfree_skb in dccp_rcv_state_process if dccp_v6_conn_request successfully returns. However, if IPV6_RECVPKTINFO is set on a socket, the address of the skb is saved to ireq->pktopts and the ref count for skb is incremented in dccp_v6_conn_request, so skb is still in use. Nevertheless, it gets freed in dccp_rcv_state_process. Fix by calling consume_skb instead of doing goto discard and therefore calling __kfree_skb. Similar fixes for TCP: fb7e2399 [TCP]: skb is unexpectedly freed. 0aea76d3 tcp: SYN packets are now simply consumed Signed-off-by:
-
Marcus Huewe authored
[ Upstream commit 7627ae60 ] When setting a neigh related sysctl parameter, we always send a NETEVENT_DELAY_PROBE_TIME_UPDATE netevent. For instance, when executing sysctl net.ipv6.neigh.wlp3s0.retrans_time_ms=2000 a NETEVENT_DELAY_PROBE_TIME_UPDATE netevent is generated. This is caused by commit 2a4501ae ("neigh: Send a notification when DELAY_PROBE_TIME changes"). According to the commit's description, it was intended to generate such an event when setting the "delay_first_probe_time" sysctl parameter. In order to fix this, only generate this event when actually setting the "delay_first_probe_time" sysctl parameter. This fix should not have any unintended side-effects, because all but one registered netevent callbacks check for other netevent event types (the registered callbacks were obtained by grepping for "register_netevent_notifier"). The only callback that uses the NETEVENT_DELAY_PROBE_TIME_UPDATE event is mlxsw_sp_router_netevent_event() (in drivers/net/ethernet/mellanox/mlxsw/spectrum_router.c): in case of this event, it only accesses the DELAY_PROBE_TIME of the passed neigh_parms. Fixes: 2a4501ae ("neigh: Send a notification when DELAY_PROBE_TIME changes") Signed-off-by:
Marcus Huewe <suse-tux@gmx.de> Reviewed-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Anoob Soman authored
[ Upstream commit 2bd624b4 ] Commit 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev"), unfortunately, introduced the following issues. 1. calling mutex_lock(&fanout_mutex) (fanout_release()) from inside rcu_read-side critical section. rcu_read_lock disables preemption, most often, which prohibits calling sleeping functions. [ ] include/linux/rcupdate.h:560 Illegal context switch in RCU read-side critical section! [ ] [ ] rcu_scheduler_active = 1, debug_locks = 0 [ ] 4 locks held by ovs-vswitchd/1969: [ ] #0: (cb_lock){++++++}, at: [<ffffffff8158a6c9>] genl_rcv+0x19/0x40 [ ] #1: (ovs_mutex){+.+.+.}, at: [<ffffffffa04878ca>] ovs_vport_cmd_del+0x4a/0x100 [openvswitch] [ ] #2: (rtnl_mutex){+.+.+.}, at: [<ffffffff81564157>] rtnl_lock+0x17/0x20 [ ] #3: (rcu_read_lock){......}, at: [<ffffffff81614165>] packet_notifier+0x5/0x3f0 [ ] [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff810c9077>] lockdep_rcu_suspicious+0x107/0x110 [ ] [<ffffffff810a2da7>] ___might_sleep+0x57/0x210 [ ] [<ffffffff810a2fd0>] __might_sleep+0x70/0x90 [ ] [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0 [ ] [<ffffffff810de93f>] ? vprintk_default+0x1f/0x30 [ ] [<ffffffff81186e88>] ? printk+0x4d/0x4f [ ] [<ffffffff816106dd>] fanout_release+0x1d/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 2. calling mutex_lock(&fanout_mutex) inside spin_lock(&po->bind_lock). "sleeping function called from invalid context" [ ] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:620 [ ] in_atomic(): 1, irqs_disabled(): 0, pid: 1969, name: ovs-vswitchd [ ] INFO: lockdep is turned off. [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff810a2f52>] ___might_sleep+0x202/0x210 [ ] [<ffffffff810a2fd0>] __might_sleep+0x70/0x90 [ ] [<ffffffff8162e80c>] mutex_lock_nested+0x3c/0x3a0 [ ] [<ffffffff816106dd>] fanout_release+0x1d/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 3. calling dev_remove_pack(&fanout->prot_hook), from inside spin_lock(&po->bind_lock) or rcu_read-side critical-section. dev_remove_pack() -> synchronize_net(), which might sleep. [ ] BUG: scheduling while atomic: ovs-vswitchd/1969/0x00000002 [ ] INFO: lockdep is turned off. [ ] Call Trace: [ ] [<ffffffff813770c1>] dump_stack+0x85/0xc4 [ ] [<ffffffff81186274>] __schedule_bug+0x64/0x73 [ ] [<ffffffff8162b8cb>] __schedule+0x6b/0xd10 [ ] [<ffffffff8162c5db>] schedule+0x6b/0x80 [ ] [<ffffffff81630b1d>] schedule_timeout+0x38d/0x410 [ ] [<ffffffff810ea3fd>] synchronize_sched_expedited+0x53d/0x810 [ ] [<ffffffff810ea6de>] synchronize_rcu_expedited+0xe/0x10 [ ] [<ffffffff8154eab5>] synchronize_net+0x35/0x50 [ ] [<ffffffff8154eae3>] dev_remove_pack+0x13/0x20 [ ] [<ffffffff8161077e>] fanout_release+0xbe/0xe0 [ ] [<ffffffff81614459>] packet_notifier+0x2f9/0x3f0 4. fanout_release() races with calls from different CPU. To fix the above problems, remove the call to fanout_release() under rcu_read_lock(). Instead, call __dev_remove_pack(&fanout->prot_hook) and netdev_run_todo will be happy that &dev->ptype_specific list is empty. In order to achieve this, I moved dev_{add,remove}_pack() out of fanout_{add,release} to __fanout_{link,unlink}. So, call to {,__}unregister_prot_hook() will make sure fanout->prot_hook is removed as well. Fixes: 66644982 ("packet: call fanout_release, while UNREGISTERING a netdev") Reported-by:
Anoob Soman <anoob.soman@citrix.com> Acked-by:
-
Eric Dumazet authored
[ Upstream commit d199fab6 ] Multiple threads can call fanout_add() at the same time. We need to grab fanout_mutex earlier to avoid races that could lead to one thread freeing po->rollover that was set by another thread. Do the same in fanout_release(), for peace of mind, and to help us finding lockdep issues earlier. Fixes: dc99f600 ("packet: Add fanout support.") Fixes: 0648ab70 ("packet: rollover prepare: per-socket state") Signed-off-by:
-
Ivan Khoronzhuk authored
[ Upstream commit a60ced99 ] There is a copy-paste error, which hides breaking of resume for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev) in suspend, but left it unchanged in resume. Fixes: 606f3993 (ti: cpsw: move platform data and slaves info to cpsw_common) Reported-by:
Alexey Starikovskiy <AStarikovskiy@topcon.com> Signed-off-by:
Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org> Signed-off-by:
-
Eric Dumazet authored
[ Upstream commit 8b74d439 ] It seems nobody used LLC since linux-3.12. Fortunately fuzzers like syzkaller still know how to run this code, otherwise it would be no fun. Setting skb->sk without skb->destructor leads to all kinds of bugs, we now prefer to be very strict about it. Ideally here we would use skb_set_owner() but this helper does not exist yet, only CAN seems to have a private helper for that. Fixes: 376c7311 ("net: add a temporary sanity check in skb_orphan()") Signed-off-by:
-
Or Gerlitz authored
[ Upstream commit fed06ee8 ] When called by HW offloading drivers, the TC action (e.g net/sched/act_mirred.c) code uses this_cpu logic, e.g _bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets) per the kernel documention, preemption should be disabled, add that. Before the fix, when running with CONFIG_PREEMPT set, we get a BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793 asserion from the TC action (mirred) stats_update callback. Fixes: aad7e08d ('net/mlx5e: Hardware offloaded flower filter statistics support') Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit cd27b96b ] In commit 98e3862c ("kcm: fix 0-length case for kcm_sendmsg()") I tried to avoid skb allocation for 0-length case, but missed a check for NULL pointer in the non EOR case. Fixes: 98e3862c ("kcm: fix 0-length case for kcm_sendmsg()") Reported-by:
Cong Wang <xiyou.wangcong@gmail.com> Acked-by:
Tom Herbert <tom@herbertland.com> Signed-off-by:
-
WANG Cong authored
[ Upstream commit 98e3862c ] Dmitry reported a kernel warning: WARNING: CPU: 3 PID: 2936 at net/kcm/kcmsock.c:627 kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627 CPU: 3 PID: 2936 Comm: a.out Not tainted 4.10.0-rc6+ #209 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:15 [inline] dump_stack+0x2ee/0x3ef lib/dump_stack.c:51 panic+0x1fb/0x412 kernel/panic.c:179 __warn+0x1c4/0x1e0 kernel/panic.c:539 warn_slowpath_null+0x2c/0x40 kernel/panic.c:582 kcm_write_msgs+0x12e3/0x1b90 net/kcm/kcmsock.c:627 kcm_sendmsg+0x163a/0x2200 net/kcm/kcmsock.c:1029 sock_sendmsg_nosec net/socket.c:635 [inline] sock_sendmsg+0xca/0x110 net/socket.c:645 sock_write_iter+0x326/0x600 net/socket.c:848 new_sync_write fs/read_write.c:499 [inline] __vfs_write+0x483/0x740 fs/read_write.c:512 vfs_write+0x187/0x530 fs/read_write.c:560 SYSC_write fs/read_write.c:607 [inline] SyS_write+0xfb/0x230 fs/read_write.c:599 entry_SYSCALL_64_fastpath+0x1f/0xc2 when calling syscall(__NR_write, sock2, 0x208aaf27ul, 0x0ul) on a KCM seqpacket socket. It appears that kcm_sendmsg() does not handle len==0 case correctly, which causes an empty skb is allocated and queued. Fix this by skipping the skb allocation for len==0 case. Reported-by:
-
- 23 Feb, 2017 20 commits
-
-
Greg Kroah-Hartman authored
-
Hans Verkuil authored
commit 35879ee4 upstream. This reverts 'commit 7e0739cd ("[media] videodev2.h: fix sYCC/AdobeYCC default quantization range"). The problem is that many drivers can convert R'G'B' content (often from sensors) to Y'CbCr, but they all produce limited range Y'CbCr. To stay backwards compatible the default quantization range for sRGB and AdobeRGB Y'CbCr encoding should be limited range, not full range, even though the corresponding standards specify full range. Update the V4L2_MAP_QUANTIZATION_DEFAULT define accordingly and also update the documentation. Fixes: 7e0739cd ("[media] videodev2.h: fix sYCC/AdobeYCC default quantization range") Signed-off-by:
Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@s-opensource.com> Signed-off-by:
-
Kent Overstreet authored
commit be628be0 upstream. Signed-off-by:
Kent Overstreet <kent.overstreet@gmail.com> Cc: Coly Li <colyli@suse.de> Signed-off-by:
-
Thomas VanSelus authored
commit 8fcd0950 upstream. Fix typo causing ntb_transport_create_queue to select the first queue every time, instead of using the next free queue. Signed-off-by:
Thomas VanSelus <tvanselus@xes-inc.com> Signed-off-by:
Aaron Sierra <asierra@xes-inc.com> Acked-by:
Allen Hubbe <Allen.Hubbe@dell.com> Fixes: fce8a7bb ("PCI-Express Non-Transparent Bridge Support") Signed-off-by:
Jon Mason <jdmason@kudzu.us> Signed-off-by:
-
Dave Jiang authored
commit 9644347c upstream. In the normal I/O execution path, ntb_perf is missing a call to dmaengine_unmap_put() after submission. That causes us to leak unmap objects. Signed-off-by:
Dave Jiang <dave.jiang@intel.com> Fixes: 8a7b6a77 ("ntb: ntb perf tool") Signed-off-by:
-
Allen Hubbe authored
commit dd62245e upstream. The call to debugfs_remove_recursive(qp->debugfs_dir) of the sub-level directory must not be later than debugfs_remove_recursive(nt_debugfs_dir) of the top-level directory. Otherwise, the sub-level directory will not exist, and it would be invalid (panic) to attempt to remove it. This removes the top-level directory last, after sub-level directories have been cleaned up. Signed-off-by:
-
Sergey Senozhatsky authored
commit f222449c upstream. We cannot do printk() from tk_debug_account_sleep_time(), because tk_debug_account_sleep_time() is called under tk_core seq lock. The reason why printk() is unsafe there is that console_sem may invoke scheduler (up()->wake_up_process()->activate_task()), which, in turn, can return back to timekeeping code, for instance, via get_time()->ktime_get(), deadlocking the system on tk_core seq lock. [ 48.950592] ====================================================== [ 48.950622] [ INFO: possible circular locking dependency detected ] [ 48.950622] 4.10.0-rc7-next-20170213+ #101 Not tainted [ 48.950622] ------------------------------------------------------- [ 48.950622] kworker/0:0/3 is trying to acquire lock: [ 48.950653] (tk_core){----..}, at: [<c01cc624>] retrigger_next_event+0x4c/0x90 [ 48.950683] but task is already holding lock: [ 48.950683] (hrtimer_bases.lock){-.-...}, at: [<c01cc610>] retrigger_next_event+0x38/0x90 [ 48.950714] which lock already depends on the new lock. [ 48.950714] the existing dependency chain (in reverse order) is: [ 48.950714] -> #5 (hrtimer_bases.lock){-.-...}: [ 48.950744] _raw_spin_lock_irqsave+0x50/0x64 [ 48.950775] lock_hrtimer_base+0x28/0x58 [ 48.950775] hrtimer_start_range_ns+0x20/0x5c8 [ 48.950775] __enqueue_rt_entity+0x320/0x360 [ 48.950805] enqueue_rt_entity+0x2c/0x44 [ 48.950805] enqueue_task_rt+0x24/0x94 [ 48.950836] ttwu_do_activate+0x54/0xc0 [ 48.950836] try_to_wake_up+0x248/0x5c8 [ 48.950836] __setup_irq+0x420/0x5f0 [ 48.950836] request_threaded_irq+0xdc/0x184 [ 48.950866] devm_request_threaded_irq+0x58/0xa4 [ 48.950866] omap_i2c_probe+0x530/0x6a0 [ 48.950897] platform_drv_probe+0x50/0xb0 [ 48.950897] driver_probe_device+0x1f8/0x2cc [ 48.950897] __driver_attach+0xc0/0xc4 [ 48.950927] bus_for_each_dev+0x6c/0xa0 [ 48.950927] bus_add_driver+0x100/0x210 [ 48.950927] driver_register+0x78/0xf4 [ 48.950958] do_one_initcall+0x3c/0x16c [ 48.950958] kernel_init_freeable+0x20c/0x2d8 [ 48.950958] kernel_init+0x8/0x110 [ 48.950988] ret_from_fork+0x14/0x24 [ 48.950988] -> #4 (&rt_b->rt_runtime_lock){-.-...}: [ 48.951019] _raw_spin_lock+0x40/0x50 [ 48.951019] rq_offline_rt+0x9c/0x2bc [ 48.951019] set_rq_offline.part.2+0x2c/0x58 [ 48.951049] rq_attach_root+0x134/0x144 [ 48.951049] cpu_attach_domain+0x18c/0x6f4 [ 48.951049] build_sched_domains+0xba4/0xd80 [ 48.951080] sched_init_smp+0x68/0x10c [ 48.951080] kernel_init_freeable+0x160/0x2d8 [ 48.951080] kernel_init+0x8/0x110 [ 48.951080] ret_from_fork+0x14/0x24 [ 48.951110] -> #3 (&rq->lock){-.-.-.}: [ 48.951110] _raw_spin_lock+0x40/0x50 [ 48.951141] task_fork_fair+0x30/0x124 [ 48.951141] sched_fork+0x194/0x2e0 [ 48.951141] copy_process.part.5+0x448/0x1a20 [ 48.951171] _do_fork+0x98/0x7e8 [ 48.951171] kernel_thread+0x2c/0x34 [ 48.951171] rest_init+0x1c/0x18c [ 48.951202] start_kernel+0x35c/0x3d4 [ 48.951202] 0x8000807c [ 48.951202] -> #2 (&p->pi_lock){-.-.-.}: [ 48.951232] _raw_spin_lock_irqsave+0x50/0x64 [ 48.951232] try_to_wake_up+0x30/0x5c8 [ 48.951232] up+0x4c/0x60 [ 48.951263] __up_console_sem+0x2c/0x58 [ 48.951263] console_unlock+0x3b4/0x650 [ 48.951263] vprintk_emit+0x270/0x474 [ 48.951293] vprintk_default+0x20/0x28 [ 48.951293] printk+0x20/0x30 [ 48.951324] kauditd_hold_skb+0x94/0xb8 [ 48.951324] kauditd_thread+0x1a4/0x56c [ 48.951324] kthread+0x104/0x148 [ 48.951354] ret_from_fork+0x14/0x24 [ 48.951354] -> #1 ((console_sem).lock){-.....}: [ 48.951385] _raw_spin_lock_irqsave+0x50/0x64 [ 48.951385] down_trylock+0xc/0x2c [ 48.951385] __down_trylock_console_sem+0x24/0x80 [ 48.951385] console_trylock+0x10/0x8c [ 48.951416] vprintk_emit+0x264/0x474 [ 48.951416] vprintk_default+0x20/0x28 [ 48.951416] printk+0x20/0x30 [ 48.951446] tk_debug_account_sleep_time+0x5c/0x70 [ 48.951446] __timekeeping_inject_sleeptime.constprop.3+0x170/0x1a0 [ 48.951446] timekeeping_resume+0x218/0x23c [ 48.951477] syscore_resume+0x94/0x42c [ 48.951477] suspend_enter+0x554/0x9b4 [ 48.951477] suspend_devices_and_enter+0xd8/0x4b4 [ 48.951507] enter_state+0x934/0xbd4 [ 48.951507] pm_suspend+0x14/0x70 [ 48.951507] state_store+0x68/0xc8 [ 48.951538] kernfs_fop_write+0xf4/0x1f8 [ 48.951538] __vfs_write+0x1c/0x114 [ 48.951538] vfs_write+0xa0/0x168 [ 48.951568] SyS_write+0x3c/0x90 [ 48.951568] __sys_trace_return+0x0/0x10 [ 48.951568] -> #0 (tk_core){----..}: [ 48.951599] lock_acquire+0xe0/0x294 [ 48.951599] ktime_get_update_offsets_now+0x5c/0x1d4 [ 48.951629] retrigger_next_event+0x4c/0x90 [ 48.951629] on_each_cpu+0x40/0x7c [ 48.951629] clock_was_set_work+0x14/0x20 [ 48.951660] process_one_work+0x2b4/0x808 [ 48.951660] worker_thread+0x3c/0x550 [ 48.951660] kthread+0x104/0x148 [ 48.951690] ret_from_fork+0x14/0x24 [ 48.951690] other info that might help us debug this: [ 48.951690] Chain exists of: tk_core --> &rt_b->rt_runtime_lock --> hrtimer_bases.lock [ 48.951721] Possible unsafe locking scenario: [ 48.951721] CPU0 CPU1 [ 48.951721] ---- ---- [ 48.951721] lock(hrtimer_bases.lock); [ 48.951751] lock(&rt_b->rt_runtime_lock); [ 48.951751] lock(hrtimer_bases.lock); [ 48.951751] lock(tk_core); [ 48.951782] *** DEADLOCK *** [ 48.951782] 3 locks held by kworker/0:0/3: [ 48.951782] #0: ("events"){.+.+.+}, at: [<c0156590>] process_one_work+0x1f8/0x808 [ 48.951812] #1: (hrtimer_work){+.+...}, at: [<c0156590>] process_one_work+0x1f8/0x808 [ 48.951843] #2: (hrtimer_bases.lock){-.-...}, at: [<c01cc610>] retrigger_next_event+0x38/0x90 [ 48.951843] stack backtrace: [ 48.951873] CPU: 0 PID: 3 Comm: kworker/0:0 Not tainted 4.10.0-rc7-next-20170213+ [ 48.951904] Workqueue: events clock_was_set_work [ 48.951904] [<c0110208>] (unwind_backtrace) from [<c010c224>] (show_stack+0x10/0x14) [ 48.951934] [<c010c224>] (show_stack) from [<c04ca6c0>] (dump_stack+0xac/0xe0) [ 48.951934] [<c04ca6c0>] (dump_stack) from [<c019b5cc>] (print_circular_bug+0x1d0/0x308) [ 48.951965] [<c019b5cc>] (print_circular_bug) from [<c019d2a8>] (validate_chain+0xf50/0x1324) [ 48.951965] [<c019d2a8>] (validate_chain) from [<c019ec18>] (__lock_acquire+0x468/0x7e8) [ 48.951995] [<c019ec18>] (__lock_acquire) from [<c019f634>] (lock_acquire+0xe0/0x294) [ 48.951995] [<c019f634>] (lock_acquire) from [<c01d0ea0>] (ktime_get_update_offsets_now+0x5c/0x1d4) [ 48.952026] [<c01d0ea0>] (ktime_get_update_offsets_now) from [<c01cc624>] (retrigger_next_event+0x4c/0x90) [ 48.952026] [<c01cc624>] (retrigger_next_event) from [<c01e4e24>] (on_each_cpu+0x40/0x7c) [ 48.952056] [<c01e4e24>] (on_each_cpu) from [<c01cafc4>] (clock_was_set_work+0x14/0x20) [ 48.952056] [<c01cafc4>] (clock_was_set_work) from [<c015664c>] (process_one_work+0x2b4/0x808) [ 48.952087] [<c015664c>] (process_one_work) from [<c0157774>] (worker_thread+0x3c/0x550) [ 48.952087] [<c0157774>] (worker_thread) from [<c015d644>] (kthread+0x104/0x148) [ 48.952087] [<c015d644>] (kthread) from [<c0107830>] (ret_from_fork+0x14/0x24) Replace printk() with printk_deferred(), which does not call into the scheduler. Fixes: 0bf43f15 ("timekeeping: Prints the amounts of time spent during suspend") Reported-and-tested-by:
Tony Lindgren <tony@atomide.com> Signed-off-by:
Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Cc: Petr Mladek <pmladek@suse.com> Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: "Rafael J . Wysocki" <rjw@rjwysocki.net> Cc: Steven Rostedt <rostedt@goodmis.org> Cc: John Stultz <john.stultz@linaro.org> Link: http://lkml.kernel.org/r/20170215044332.30449-1-sergey.senozhatsky@gmail.comSigned-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
-
Sergey Senozhatsky authored
commit fc98c3c8 upstream. Use rcuidle console tracepoint because, apparently, it may be issued from an idle CPU: hw-breakpoint: Failed to enable monitor mode on CPU 0. hw-breakpoint: CPU 0 failed to disable vector catch =============================== [ ERR: suspicious RCU usage. ] 4.10.0-rc8-next-20170215+ #119 Not tainted ------------------------------- ./include/trace/events/printk.h:32 suspicious rcu_dereference_check() usage! other info that might help us debug this: RCU used illegally from idle CPU! rcu_scheduler_active = 2, debug_locks = 0 RCU used illegally from extended quiescent state! 2 locks held by swapper/0/0: #0: (cpu_pm_notifier_lock){......}, at: [<c0237e2c>] cpu_pm_exit+0x10/0x54 #1: (console_lock){+.+.+.}, at: [<c01ab350>] vprintk_emit+0x264/0x474 stack backtrace: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.10.0-rc8-next-20170215+ #119 Hardware name: Generic OMAP4 (Flattened Device Tree) console_unlock vprintk_emit vprintk_default printk reset_ctrl_regs dbg_cpu_pm_notify notifier_call_chain cpu_pm_exit omap_enter_idle_coupled cpuidle_enter_state cpuidle_enter_state_coupled do_idle cpu_startup_entry start_kernel This RCU warning, however, is suppressed by lockdep_off() in printk(). lockdep_off() increments the ->lockdep_recursion counter and thus disables RCU_LOCKDEP_WARN() and debug_lockdep_rcu_enabled(), which want lockdep to be enabled "current->lockdep_recursion == 0". Link: http://lkml.kernel.org/r/20170217015932.11898-1-sergey.senozhatsky@gmail.comSigned-off-by:
Paul E. McKenney <paulmck@linux.vnet.ibm.com> Acked-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Cc: Petr Mladek <pmladek@suse.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Tony Lindgren <tony@atomide.com> Cc: Russell King <rmk@armlinux.org.uk> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Yinghai Lu authored
commit afe3e4d1 upstream. In addition to making PME non-modular, d7def204 ("PCI/PME: Make explicitly non-modular") removed the pcie_pme_driver .remove() method, pcie_pme_remove(). pcie_pme_remove() freed the PME IRQ that was requested in pci_pme_probe(). The fact that we don't free the IRQ after d7def204 causes the following crash when removing a PCIe port device via /sys: ------------[ cut here ]------------ kernel BUG at drivers/pci/msi.c:370! invalid opcode: 0000 [#1] SMP Modules linked in: CPU: 1 PID: 14509 Comm: sh Tainted: G W 4.8.0-rc1-yh-00012-gd29438d6 RIP: 0010:[<ffffffff9758bbf5>] free_msi_irqs+0x65/0x190 ... Call Trace: [<ffffffff9758cda4>] pci_disable_msi+0x34/0x40 [<ffffffff97583817>] cleanup_service_irqs+0x27/0x30 [<ffffffff97583e9a>] pcie_port_device_remove+0x2a/0x40 [<ffffffff97584250>] pcie_portdrv_remove+0x40/0x50 [<ffffffff97576d7b>] pci_device_remove+0x4b/0xc0 [<ffffffff9785ebe6>] __device_release_driver+0xb6/0x150 [<ffffffff9785eca5>] device_release_driver+0x25/0x40 [<ffffffff975702e4>] pci_stop_bus_device+0x74/0xa0 [<ffffffff975704ea>] pci_stop_and_remove_bus_device_locked+0x1a/0x30 [<ffffffff97578810>] remove_store+0x50/0x70 [<ffffffff9785a378>] dev_attr_store+0x18/0x30 [<ffffffff97260b64>] sysfs_kf_write+0x44/0x60 [<ffffffff9725feae>] kernfs_fop_write+0x10e/0x190 [<ffffffff971e13f8>] __vfs_write+0x28/0x110 [<ffffffff970b0fa4>] ? percpu_down_read+0x44/0x80 [<ffffffff971e53a7>] ? __sb_start_write+0xa7/0xe0 [<ffffffff971e53a7>] ? __sb_start_write+0xa7/0xe0 [<ffffffff971e1f04>] vfs_write+0xc4/0x180 [<ffffffff971e3089>] SyS_write+0x49/0xa0 [<ffffffff97001a46>] do_syscall_64+0xa6/0x1b0 [<ffffffff9819201e>] entry_SYSCALL64_slow_path+0x25/0x25 ... RIP [<ffffffff9758bbf5>] free_msi_irqs+0x65/0x190 RSP <ffff89ad3085bc48> ---[ end trace f4505e1dac5b95d3 ]--- Segmentation fault Restore pcie_pme_remove(). [bhelgaas: changelog] Fixes: d7def204 ("PCI/PME: Make explicitly non-modular") Signed-off-by:
Yinghai Lu <yinghai@kernel.org> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Acked-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Jarkko Nikula authored
commit 12688dc2 upstream. This reverts commit 63d0f0a6. It caused a regression on platforms where I2C controller is synthesized with dynamic TAR update disabled. Detection code is testing is bit DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to restore original value in case bit is read-write. Instead of fixing this we revert the commit since it was preparation for the commit 0317e6c0 ("i2c: designware: do not disable adapter after transfer") which was also reverted. Reported-by:
Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com> Reported-by:
Suravee Suthikulpanit <suravee.suthikulpanit@amd.com> Acked-By:
Lucas De Marchi <lucas.demarchi@intel.com> Fixes: 63d0f0a6 ("i2c: designware: detect when dynamic tar update is possible") Signed-off-by:
Jarkko Nikula <jarkko.nikula@linux.intel.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Kees Cook authored
commit 9e344048 upstream. The 64-bit get_user() wasn't clearing the high word due to a typo in the error handler. The exception handler entry was already correct, though. Noticed during recent usercopy test additions in lib/test_user_copy.c. Signed-off-by:
Kees Cook <keescook@chromium.org> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Yang Yang authored
commit 25f71d1c upstream. The UEVENT user mode helper is enabled before the initcalls are executed and is available when the root filesystem has been mounted. The user mode helper is triggered by device init calls and the executable might use the futex syscall. futex_init() is marked __initcall which maps to device_initcall, but there is no guarantee that futex_init() is invoked _before_ the first device init call which triggers the UEVENT user mode helper. If the user mode helper uses the futex syscall before futex_init() then the syscall crashes with a NULL pointer dereference because the futex subsystem has not been initialized yet. Move futex_init() to core_initcall so futexes are initialized before the root filesystem is mounted and the usermode helper becomes available. [ tglx: Rewrote changelog ] Signed-off-by:
Yang Yang <yang.yang29@zte.com.cn> Cc: jiang.biao2@zte.com.cn Cc: jiang.zhengxiong@zte.com.cn Cc: zhong.weidong@zte.com.cn Cc: deng.huali@zte.com.cn Cc: Peter Zijlstra <peterz@infradead.org> Link: http://lkml.kernel.org/r/1483085875-6130-1-git-send-email-yang.yang29@zte.com.cnSigned-off-by:
-
Pierre-Louis Bossart authored
commit bb08c04d upstream. 100% reproducible issue found on SKL SkullCanyon NUC with two external DP daisy-chained monitors in DP/MST mode. When turning off or changing the input of the second monitor the machine stops with a kernel oops. This issue happened with 4.8.8 as well as drm/drm-intel-nightly. This issue is traced to an inconsistent control flow in drm_dp_update_payload_part1(): the 'port' pointer is set to NULL at the same time as 'req_payload.num_slots' is set to zero, but the pointer is dereferenced even when req_payload.num_slot is zero. The problematic dereference was introduced in commit dfda0df3 ("drm/mst: rework payload table allocation to conform better") and may impact all versions since v3.18 The fix suggested by Chris Wilson removes the kernel oops and was found to work well after 10mn of monkey-testing with the second monitor power and input buttons Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98990 Fixes: dfda0df3 ("drm/mst: rework payload table allocation to conform better.") Cc: Dave Airlie <airlied@redhat.com> Cc: Chris Wilson <chris@chris-wilson.co.uk> Cc: Nathan D Ciobanu <nathan.d.ciobanu@linux.intel.com> Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Cc: Sean Paul <seanpaul@chromium.org> Tested-by:
Nathan D Ciobanu <nathan.d.ciobanu@linux.intel.com> Reviewed-by:
Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com> Signed-off-by:
Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com> Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1487076561-2169-1-git-send-email-jani.nikula@intel.comSigned-off-by:
-
Michel Dänzer authored
commit d74c67dd upstream. The crtc_h/vdisplay fields may not match the CRTC viewport dimensions with special modes such as interlaced ones. Fixes the HW cursor disappearing in the bottom half of the screen with interlaced modes. Fixes: 6b16cf77 ("drm/radeon: Hide the HW cursor while it's out of bounds") Reported-by:
Ashutosh Kumar <ashutosh.kumar@amd.com> Tested-by:
Sonny Jiang <sonny.jiang@amd.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Signed-off-by:
-
IHARA Hiroka authored
commit 722c5ac7 upstream. ELAN0605 has been confirmed to be a variant of ELAN0600, which is blacklisted in the hid-core to be managed by elan_i2c. This device can be found in Lenovo ideapad 310s (80U4000). Signed-off-by:
Hiroka IHARA <ihara_h@live.jp> Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Al Viro authored
commit 137d01df upstream. What happens is that a write to /dev/sg is given a request with non-zero ->iovec_count combined with zero ->dxfer_len. Or with ->dxferp pointing to an array full of empty iovecs. Having write permission to /dev/sg shouldn't be equivalent to the ability to trigger BUG_ON() while holding spinlocks... Found by Dmitry Vyukov and syzkaller. [ The BUG_ON() got changed to a WARN_ON_ONCE(), but this fixes the underlying issue. - Linus ] Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Reported-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Johannes Thumshirn authored
commit fd3fc0b4 upstream. Don't crash the machine just because of an empty transfer. Use WARN_ON() combined with returning an error. Found by Dmitry Vyukov and syzkaller. [ Changed to "WARN_ON_ONCE()". Al has a patch that should fix the root cause, but a BUG_ON() is not acceptable in any case, and a WARN_ON() might still be a cause of excessive log spamming. NOTE! If this warning ever triggers, we may end up leaking resources, since this doesn't bother to try to clean the command up. So this WARN_ON_ONCE() triggering does imply real problems. But BUG_ON() is much worse. People really need to stop using BUG_ON() for "this shouldn't ever happen". It makes pretty much any bug worse. - Linus ] Signed-off-by:
Johannes Thumshirn <jthumshirn@suse.de> Reported-by:
-
Paul Mackerras authored
commit 3f91a89d upstream. Currently, if the kernel is running on a POWER9 processor under a hypervisor, it may try to use the radix MMU even though it doesn't have the necessary code to do so (it doesn't negotiate use of radix, and it doesn't do the H_REGISTER_PROC_TBL hcall). If the hypervisor supports both radix and HPT, then it will set up the guest to use HPT (since the guest doesn't request radix in the CAS call), but if the radix feature bit is set in the ibm,pa-features property (which is valid, since ibm,pa-features is defined to represent the capabilities of the processor) the guest will try to use radix, resulting in a crash when it turns the MMU on. This makes the minimal fix for the current code, which is to disable radix unless we are running in hypervisor mode. Fixes: 2bfd65e4 ("powerpc/mm/radix: Add radix callbacks for early init routines") Signed-off-by:
Paul Mackerras <paulus@ozlabs.org> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Anssi Hannula authored
commit 3d4ef329 upstream. Commit 577fb131 ("mmc: rework selection of bus speed mode") refactored bus width selection code to mmc_select_bus_width(). However, it also altered the behavior to not call the selection code in non-high-speed modes anymore. This causes 1-bit mode to always be used when the high-speed mode is not enabled, even though 4-bit and 8-bit bus are valid bus widths in the backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed Modes in JEDEC 84-B50). This results in a significant regression in transfer speeds. Fix the code to allow 4-bit and 8-bit widths even without high-speed mode, as before. Tested with a Zynq-7000 PicoZed 7020 board. Fixes: 577fb131 ("mmc: rework selection of bus speed mode") Signed-off-by:
Anssi Hannula <anssi.hannula@bitwise.fi> Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
-
Miklos Szeredi authored
commit 84588a93 upstream. Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Fixes: d82718e3 ("fuse_dev_splice_read(): switch to add_to_pipe()") Signed-off-by:
-
