The maximum size of a shmem/tmpfs file has been limited by the maximum
size of its triple-indirect swap vector.  With 4kB page size, maximum
filesize was just over 2TB on a 32-bit kernel, but sadly one eighth of
that on a 64-bit kernel.  (With 8kB page size, maximum filesize was just
over 4TB on a 64-bit kernel, but 16TB on a 32-bit kernel,
MAX_LFS_FILESIZE being then more restrictive than swap vector layout.)

It's a shame that tmpfs should be more restrictive than ramfs, and this
limitation has now been noticed.  Add another level to the swap vector?
No, it became obscure and hard to maintain, once I complicated it to
make use of highmem pages nine years ago: better choose another way.

Surely, if 2.4 had had the radix tree pagecache introduced in 2.5, then
tmpfs would never have invented its own peculiar radix tree: we would
have fitted swap entries into the common radix tree instead, in much the
same way as we fit swap entries into page tables.

And why should each file have a separate radix tree for its pages and
for its swap entries? The swap entries are required precisely where and
when the pages are not.  We want to put them together in a single radix
tree: which can then avoid much of the locking which was needed to
prevent them from being exchanged underneath us.

This also avoids the waste of memory devoted to swap vectors, first in
the shmem_inode itself, then at least two more pages once a file grew
beyond 16 data pages (pages accounted by df and du, but not by memcg).
Allocated upfront, to avoid allocation when under swapping pressure, but
pure waste when CONFIG_SWAP is not set - I have never spattered around
the ifdefs to prevent that, preferring this move to sharing the common
radix tree instead.

There are three downsides to sharing the radix tree.  One, that it binds
tmpfs more tightly to the rest of mm, either requiring knowledge of swap
entries in radix tree there, or duplication of its code here in shmem.c.
I believe that the simplications and memory savings (and probable higher
performance, not yet measured) justify that.

Two, that on HIGHMEM systems with SWAP enabled, it's the lowmem radix
nodes that cannot be freed under memory pressure - whereas before it was
the less precious highmem swap vector pages that could not be freed.
I'm hoping that 64-bit has now been accessible for long enough, that the
highmem argument has grown much less persuasive.

Three, that swapoff is slower than it used to be on tmpfs files, since
it's using a simple generic mechanism not tailored to it: I find this
noticeable, and shall want to improve, but maybe nobody else will
notice.

So...  now remove most of the old swap vector code from shmem.c.  But,
for the moment, keep the simple i_direct vector of 16 pages, with simple
accessors shmem_put_swap() and shmem_get_swap(), as a toy implementation
to help mark where swap needs to be handled in subsequent patches.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

If swap entries are to be stored along with struct page pointers in a
radix tree, they need to be distinguished as exceptional entries.

Most of the handling of swap entries in radix tree will be contained in
shmem.c, but a few functions in filemap.c's common code need to check
for their appearance: find_get_page(), find_lock_page(),
find_get_pages() and find_get_pages_contig().

So as not to slow their fast paths, tuck those checks inside the
existing checks for unlikely radix_tree_deref_slot(); except for
find_lock_page(), where it is an added test.  And make it a BUG in
find_get_pages_tag(), which is not applied to tmpfs files.

A part of the reason for eliminating shmem_readpage() earlier, was to
minimize the places where common code would need to allow for swap
entries.

The swp_entry_t known to swapfile.c must be massaged into a slightly
different form when stored in the radix tree, just as it gets massaged
into a pte_t when stored in page tables.

In an i386 kernel this limits its information (type and page offset) to
30 bits: given 32 "types" of swapfile and 4kB pagesize, that's a maximum
swapfile size of 128GB.  Which is less than the 512GB we previously
allowed with X86_PAE (where the swap entry can occupy the entire upper
32 bits of a pte_t), but not a new limitation on 32-bit without PAE; and
there's not a new limitation on 64-bit (where swap filesize is already
limited to 16TB by a 32-bit page offset).  Thirty areas of 128GB is
probably still enough swap for a 64GB 32-bit machine.

Provide swp_to_radix_entry() and radix_to_swp_entry() conversions, and
enforce filesize limit in read_swap_header(), just as for ptes.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

A patchset to extend tmpfs to MAX_LFS_FILESIZE by abandoning its
peculiar swap vector, instead keeping a file's swap entries in the same
radix tree as its struct page pointers: thus saving memory, and
simplifying its code and locking.

This patch:

The radix_tree is used by several subsystems for different purposes.  A
major use is to store the struct page pointers of a file's pagecache for
memory management.  But what if mm wanted to store something other than
page pointers there too?

The low bit of a radix_tree entry is already used to denote an indirect
pointer, for internal use, and the unlikely radix_tree_deref_retry()
case.

Define the next bit as denoting an exceptional entry, and supply inline
functions radix_tree_exception() to return non-0 in either unlikely
case, and radix_tree_exceptional_entry() to return non-0 in the second
case.

If a subsystem already uses radix_tree with that bit set, no problem: it
does not affect internal workings at all, but is defined for the
convenience of those storing well-aligned pointers in the radix_tree.

The radix_tree_gang_lookups have an implicit assumption that the caller
can deduce the offset of each entry returned e.g.  by the page->index of
a struct page.  But that may not be feasible for some kinds of item to
be stored there.

radix_tree_gang_lookup_slot() allow for an optional indices argument,
output array in which to return those offsets.  The same could be added
to other radix_tree_gang_lookups, but for now keep it to the only one
for which we need it.
Signed-off-by: Hugh Dickins <hughd@google.com>
Acked-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

i386 allmodconfig:

  drivers/built-in.o: In function `aat2870_bl_remove':
  aat2870_bl.c:(.text+0x414f9): undefined reference to `backlight_device_unregister'
  drivers/built-in.o: In function `aat2870_bl_probe':
  aat2870_bl.c:(.text+0x418fc): undefined reference to `backlight_device_register'
  aat2870_bl.c:(.text+0x41a31): undefined reference to `backlight_device_unregiste

Cc: Jin Park <jinyoungp@nvidia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

 - Current implementation tests wrong value for setting
   aat2870_bl->max_current.

 - In the current implementation, we cannot differentiate between 2 cases:

   a) if pdata->max_current is not set , or

   b) pdata->max_current is set to AAT2870_CURRENT_0_45 (which is also 0).

   Fix it by setting AAT2870_CURRENT_0_45 to be 1 and adjust the equation in
   aat2870_brightness() accordingly.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Tested-by: Jin Park <jinyoungp@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

backlight_device_register() returns ERR_PTR() on error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Jin Park <jinyoungp@nvidia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix:

  arch/cris/arch-v10/kernel/irq.c:239: error: implicit declaration of function 'kgdb_init'
  arch/cris/arch-v10/kernel/irq.c:240: error: implicit declaration of function 'breakpoint'

Declare these two functions.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix:

  arch/cris/arch-v10/drivers/sync_serial.c:961: error: conflicting types for 'sync_serial_ioctl'
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix:

  arch/cris/arch-v10/drivers/sync_serial.c:628: error: 'ret' undeclared (first use in this function)

'ret' should be 'err'.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix this error:

  kernel/fork.c:267: error: implicit declaration of function 'alloc_thread_info_node'

This is due to renaming alloc_thread_info() to alloc_thread_info_node().

[akpm@linux-foundation.org: coding-style fixes]
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix tpm_tis.c build when CONFIG_ACPI is not enabled by providing a stub
function.  Fixes many build errors/warnings:

  drivers/char/tpm/tpm_tis.c:89: error: dereferencing pointer to incomplete type
  drivers/char/tpm/tpm_tis.c:89: warning: type defaults to 'int' in declaration of 'type name'
  drivers/char/tpm/tpm_tis.c:89: error: request for member 'list' in something not a structure or union
  ...
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Leendert van Doorn <leendert@watson.ibm.com>
Cc: James Morris <jmorris@namei.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

__GFP_OTHER_NODE is used for NUMA allocations on behalf of other nodes.
It's supposed to be passed through from the page allocator to
zone_statistics(), but it never gets there as gfp_allowed_mask is not
wide enough and masks out the flag early in the allocation path.

The result is an accounting glitch where successful NUMA allocations
by-agent are not properly attributed as local.

Increase __GFP_BITS_SHIFT so that it includes __GFP_OTHER_NODE.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Andi Kleen <ak@linux.intel.com>
Reviewed-by: Minchan Kim <minchan.kim@gmail.com>
Acked-by: Mel Gorman <mgorman@suse.de>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update the module parameters when platform data is used.  This means
that they can be read from /sys/module/ramoops/parameters in order to
parse the memory area.
Signed-off-by: Sergiu Iordache <sergiu@chromium.org>
Cc: Marco Stornelli <marco.stornelli@gmail.com>
Cc: Seiji Aguchi <seiji.aguchi@hds.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Update kernel-parameters.txt to point users to the authoritative comment
for name_to_dev_t.  In addition, updates other places where some
name_to_dev_t behavior was discussed.  All other references to root=
appear to be for explicit sample usage or just side comments when
discussing other kernel parameters.
Signed-off-by: Will Drewry <wad@chromium.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Namhyung Kim <namhyung@gmail.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix new kernel-doc warning in fs/dcache.c:

  Warning(fs/dcache.c:797): No description found for parameter 'sb'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The current hyper-optimized functions are overkill if you simply want to
allocate an id for a device.  Create versions which use an internal
lock.

In followup patches, numerous drivers are converted to use this
interface.

Thanks to Tejun for feedback.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

When send_cpu_listeners() finds the orphaned listener it marks it as
!valid and drops listeners->sem.  Before it takes this sem for writing,
s->pid can be reused and add_del_listener() can wrongly try to re-use
this entry.

Change add_del_listener() to check ->valid = T.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Cc: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

1. Commit 26c4caea "don't allow duplicate entries in listener mode"
   changed add_del_listener(REGISTER) so that "next_cpu:" can reuse the
   listener allocated for the previous cpu, this doesn't look exactly
   right even if minor.

   Change the code to kfree() in the already-registered case, this case
   is unlikely anyway so the extra kmalloc_node() shouldn't hurt but
   looke more correct and clean.

2. use the plain list_for_each_entry() instead of _safe() to scan
   listeners->list.

3. Remove the unneeded INIT_LIST_HEAD(&s->list), we are going to
   list_add(&s->list).
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Reviewed-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Balbir Singh <bsingharora@gmail.com>
Reviewed-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As the comment explains, the intention of the code is to clear the
OMAP_RTC_CTRL_MODE_12_24 bit, but instead it only clears the
OMAP_RTC_CTRL_SPLIT and OMAP_RTC_CTRL_AUTO_COMP bits, which should be
kept.  OMAP_RTC_CTRL_DISABLE, OMAP_RTC_CTRL_SET_32_COUNTER,
OMAP_RTC_CTRL_TEST, and OMAP_RTC_CTRL_ROUND_30S are also better off
being cleared.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

init_fault_attr_dentries() is used to export fault_attr via debugfs.
But it can only export it in debugfs root directory.

Per Forlin is working on mmc_fail_request which adds support to inject
data errors after a completed host transfer in MMC subsystem.

The fault_attr for mmc_fail_request should be defined per mmc host and
export it in debugfs directory per mmc host like
/sys/kernel/debug/mmc0/mmc_fail_request.

init_fault_attr_dentries() doesn't help for mmc_fail_request.  So this
introduces fault_create_debugfs_attr() which is able to create a
directory in the arbitrary directory and replace
init_fault_attr_dentries().

[akpm@linux-foundation.org: extraneous semicolon, per Randy]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Per Forlin <per.forlin@linaro.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'pstore-efi' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  efivars: fix warnings when CONFIG_PSTORE=n

* 'tools-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
  tools/power turbostat: fit output into 80 columns on snb-ep
  tools/power x86_energy_perf_policy: fix print of uninitialized string

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (28 commits)
  ACPI:  delete stale reference in kernel-parameters.txt
  ACPI: add missing _OSI strings
  ACPI: remove NID_INVAL
  thermal: make THERMAL_HWMON implementation fully internal
  thermal: split hwmon lookup to a separate function
  thermal: hide CONFIG_THERMAL_HWMON
  ACPI print OSI(Linux) warning only once
  ACPI: DMI workaround for Asus A8N-SLI Premium and Asus A8N-SLI DELUX
  ACPI / Battery: propagate sysfs error in acpi_battery_add()
  ACPI / Battery: avoid acpi_battery_add() use-after-free
  ACPI: introduce "acpi_rsdp=" parameter for kdump
  ACPI: constify ops structs
  ACPI: fix CONFIG_X86_REROUTE_FOR_BROKEN_BOOT_IRQS
  ACPI: fix 80 char overflow
  ACPI / Battery: Resolve the race condition in the sysfs_remove_battery()
  ACPI / Battery: Add the check before refresh sysfs in the battery_notify()
  ACPI / Battery: Add the hibernation process in the battery_notify()
  ACPI / Battery: Rename acpi_battery_quirks2 with acpi_battery_quirks
  ACPI / Battery: Change 16-bit signed negative battery current into correct value
  ACPI / Battery: Add the power unit macro
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile/mm/init.c: trivial: use BUG_ON
  arch/tile: remove useless set_fixmap_nocache() macro
  arch/tile: add hypervisor-based character driver for SPI flash ROM
  ioctl-number.txt: add the tile hardwall ioctl range
  tile: use generic-y format for one-line asm-generic headers
  clocksource: tile: convert to use clocksource_register_hz

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable: (31 commits)
  Btrfs: don't call writepages from within write_full_page
  Btrfs: Remove unused variable 'last_index' in file.c
  Btrfs: clean up for find_first_extent_bit()
  Btrfs: clean up for wait_extent_bit()
  Btrfs: clean up for insert_state()
  Btrfs: remove unused members from struct extent_state
  Btrfs: clean up code for merging extent maps
  Btrfs: clean up code for extent_map lookup
  Btrfs: clean up search_extent_mapping()
  Btrfs: remove redundant code for dir item lookup
  Btrfs: make acl functions really no-op if acl is not enabled
  Btrfs: remove remaining ref-cache code
  Btrfs: remove a BUG_ON() in btrfs_commit_transaction()
  Btrfs: use wait_event()
  Btrfs: check the nodatasum flag when writing compressed files
  Btrfs: copy string correctly in INO_LOOKUP ioctl
  Btrfs: don't print the leaf if we had an error
  btrfs: make btrfs_set_root_node void
  Btrfs: fix oops while writing data to SSD partitions
  Btrfs: Protect the readonly flag of block group
  ...

Fix up trivial conflicts (due to acl and writeback cleanups) in
 - fs/btrfs/acl.c
 - fs/btrfs/ctree.h
 - fs/btrfs/extent_io.c

* 'devicetree/next' of git://git.secretlab.ca/git/linux-2.6:
  MAINTAINERS: Add keyword match for of_match_table to device tree section
  of: constify property name parameters for helper functions
  input: xilinx_ps2: Add missing of_address.h header
  of: address: use resource_size helper

* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
  spi/pl022: remove function cannot exit

* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: (34 commits)
  dm table: set flush capability based on underlying devices
  dm crypt: optionally support discard requests
  dm raid: add md raid1 support
  dm raid: support metadata devices
  dm raid: add write_mostly parameter
  dm raid: add region_size parameter
  dm raid: improve table parameters documentation
  dm ioctl: forbid multiple device specifiers
  dm ioctl: introduce __get_dev_cell
  dm ioctl: fill in device parameters in more ioctls
  dm flakey: add corrupt_bio_byte feature
  dm flakey: add drop_writes
  dm flakey: support feature args
  dm flakey: use dm_target_offset and support discards
  dm table: share target argument parsing functions
  dm snapshot: skip reading origin when overwriting complete chunk
  dm: ignore merge_bvec for snapshots when safe
  dm table: clean dm_get_device and move exports
  dm raid: tidy includes
  dm ioctl: prevent empty message
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-watchdog:
  watchdog: Cleanup WATCHDOG_CORE help text
  watchdog: Fix POST failure on ASUS P5N32-E SLI and similar boards
  watchdog: shwdt: fix usage of mod_timer

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: asihpi - Clarify adapter index validity check
  ALSA: asihpi - Don't leak firmware if mem alloc fails
  ALSA: rtctimer.c needs module.h
  ASoC: Fix txx9aclc.c build
  ALSA: hdspm - Add firmware revision 0xcc for RME MADI
  ALSA: hdspm - Fix reported external sample rate on RME MADI and MADIface
  ALSA: hdspm - Provide MADI speed mode selector on RME MADI and MADIface
  ALSA: sound/core/pcm_compat.c: adjust array index

Reduce columns for package number to 1.
If you can afford more than 9 packages,
you can also afford a terminal with more than 80 columns:-)

Also shave a column also off the package C-states
Signed-off-by: Len Brown <len.brown@intel.com>

drivers/firmware/efivars.c:161: warning: ‘utf16_strlen’ defined but not used
utf16_strlen() is only used inside CONFIG_PSTORE - make this "static inline"
to shut the compiler up [thanks to hpa for the suggestion].

drivers/firmware/efivars.c:602: warning: initialization from incompatible pointer type
Between v1 and v2 of this patch series we decided to make the "part" number
unsigned - but missed fixing the stub version of efi_pstore_write()
Acked-by: Matthew Garrett <mjg@redhat.com>
Acked-by: Mike Waychison <mikew@google.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>

Merge branches 'acpica', 'battery', 'boot-irqs', 'bz-24492', 'bz-9528', 'from-akpm', 'kexec-param' and 'misc' into release

Conflicts:
	Documentation/kernel-parameters.txt
Signed-off-by: Len Brown <len.brown@intel.com>

Says for acpi=
                        See also Documentation/power/pm.txt, pci=noacpi

but this file does not exist
Reported-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Len Brown <len.brown@intel.com>

Use BUG_ON(x) rather than if(x) BUG();

The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@ identifier x; @@
-if (x) BUG();
+BUG_ON(x);

@@ identifier x; @@
-if (!x) BUG();
+BUG_ON(!x);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>

Linux supports some optional features, but it should notify the BIOS about
them via the _OSI method.  Currently Linux doesn't notify any, which might
make such features not work because the BIOS doesn't know about them.

Jarosz has a system which needs this to make ACPI processor aggregator
device work.
Reported-by: "Jarosz, Sebastian" <sebastian.jarosz@intel.com>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>

b552a8c5 ("ACPI: remove NID_INVAL") removed the left over uses of
NID_INVAL, but didn't actually remove the definition.  Remove it.
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>

THERMAL_HWMON is implemented inside the thermal_sys driver and has no
effect on drivers implementing thermal zones, so they shouldn't see
anything related to it in <linux/thermal.h>.  Making the THERMAL_HWMON
implementation fully internal has two advantages beyond the cleaner
design:

* This avoids rebuilding all thermal drivers if the THERMAL_HWMON
  implementation changes, or if CONFIG_THERMAL_HWMON gets enabled or
  disabled.

* This avoids breaking the thermal kABI in these cases too, which should
  make distributions happy.

The only drawback I can see is slightly higher memory fragmentation, as
the number of kzalloc() calls will increase by one per thermal zone.  But
I doubt it will be a problem in practice, as I've never seen a system with
more than two thermal zones.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rene Herman <rene.herman@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>

We'll soon need to reuse it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Rene Herman <rene.herman@gmail.com>
Acked-by: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>