Ido Schimmel says:

====================
mlxsw: spectrum_router: Add GRE tunnel support for Spectrum-2

Nir says:

In Spectrum-2, HW implementation of layer 3 tunnels differs from
Spectrum-1 when it comes to the underlay routing table selection.
Spectrum-2 uses a dedicated RIF that points to the virtual router used
for forwarding the encapsulated packets, while Spectrum-1 explicitly
specifies the virtual router itself.

Patches #1 and #2 add additional fields in RITR - Router interface table
register and RTDP - Routing tunnel decap properties respectively, the
fields are required for the new underlay RIF needed for Spectrum-2.

Patches #3-4 allow different set of RIF operations per ASIC type. The
first patch splits the operations and the following patch sets RIF ops
according to ASIC type.

Patches #5-9 introduce small changes to existing code to allow existence
of a dedicated underlay RIF along with the underlay virtual router, and
to support that new type of RIF that has no device.

Patch #10 takes care of updating the tunnel decap properties egress
underlay RIF required for Spectrum-2.

Patch #11 adds the implementation of Spectrum-2 specific RIF operations
and essentially enables layer 3 GRE tunnels on Spectrum-2.

Finally patches #12-18 add tests for GRE IP-in-IP tunnels, both in flat
and hierarchical topologies.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on hierarchical topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on hierarchical topology described
in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on hierarchical topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where an ikey/okey pair is set. This test is based on flat topology
described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
where a key is set. This test is based on flat topology described in file
ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a test that checks IP-in-IP GRE tunneling and MTU change of tunnel,
based on flat topology described in file ipip_lib.sh.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a library with helper functions, to be used in testing IP-in-IP and GRE
tunnels, both in flat and in hierarchical topologies.
The topologies used in this library cover the three scenarios of tunnels -
a tunel with no bound device, a tunnel with bound device in the same VRF
and a tunnel with a bound device in a different VRF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 GRE tunnel implementation requires a specific underlay RIF that
points to the virtual router used for forwarding the encapsulated packet.

Add Spectrum-2 specific loopback router interface creation methods which
may create or reuse the dedicated underlay RIF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 requires to specify the egress RIF when setting tunnel decap
properties. Add a method for accessing the underlay RIF index and then use
it when setting decap properties.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 underlay RIF is merely an auxiliary RIF that points to the
virtual router used for encapsulated packets lookup. It exists only when
its overlay RIF exists but may be shared with other overlay RIFs.
Hence it is undesired to mark any device as related to it.

Therefore allow usage of NULL device when allocating RIF.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For the sake of Spectrum-2 GRE support, as ul_vr_id field is reserved for
Spectrum-2, Change mlxsw_sp_ipip_lb_ul_vr_id() implementation not to use
the reserved field.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Spectrum-2 GRE tunnels underlay should be given not only the virtual router
information for an encapsulated packet lookup, but also an underlay RIF
object which belongs to a virtual router.

Therefore add ul_rif_id field in struct mlxsw_sp_rif_ipip_lb, to be used
later in Spectrum-2 underlay RIF implementation. This field complements
ul_vr_id field, already present and defined as reserved for Spectrum-2.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The presence of an allocated RIF in mlxsw_sp->router->rifs[rif_index] marks
that rif_index as taken.
Set the marking of a taken RIF to happen before calling ops->create in
order to allow creation of a GRE underlay RIF, which may be allocated and
created as part of an overlay RIF creation.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Spectrum-2, the underlay routing table is pointed by an underlay router
interface in contrary to Spectrum where only an underlay virtual router
should be set. That makes the underlay virtual router field in RITR
reserved for Spectrum-2.

Change loopback RIF creation function to support the new underlay RIF
field, however leave this field reserved for Spectrum-1 updates.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Set RIF ops array as member of mlxsw_sp in order to control which RIF
operations callbacks are called per ASIC type. This is needed to control
per ASIC handling of loopback RIF configurations.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Split RIF ops array for Spectrum-1 and Spectrum-2 callbacks in order to
support different sets of operations for loopback RIF handling, as
underlying implementation differs between the ASICs.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In Spectrum-2 we need to specify the underlay egress router interface
when performing IP-in-IP and NVE packet decapsulation in the underlay
router.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add fields relevant for Spectrum-2 Loopback IPinIP router interface
creation. Add additional Loopback RIF protocol value - Generic, used for
creation of an explicit underlay RIF, and also add a field named
underlay_rif used for specifying the underlay RIF of a tunnel.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: series with smaller improvements

Series with smaller improvements.

v2:
- fixed a small copy & paste error in patch 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl_init_one() is complex enough, so we better factor out getting the
ether_clk.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Accessing the phy_device indirectly via the netdevice causes few issues:
- Accessing the phy_device when it's not attached may cause a NPE.
- If we have to access the phy_device when it's not attached we have
  to use mdiobus_get_phy() to get a reference to the phy_device.

Therefore store a phy_device reference in struct rtl8169_private directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Triggering an asynchronous reset is problematic for the following
reasons, therefore reset the chip synchronously.

- The reset routine resets registers and parameters behind our back
  what may collide with code executed after triggering the reset.

- __rtl8169_resume() is called as part of pm_runtime_get_sync() and
  callers expect that the chip is fully resumed afterwards.

In context of this driver triggering an asynchonous reset should be
considered an emergency procedure.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add helpers for locking / unlocking the config registers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All calls to this function have the enable parameter set to false.
So we can replace the function with a disable-only version.

v2:
- fixed copy & paste error
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

It's sufficient to initialize the workqueue once, therefore remove the
additional initialization whenever rtl_open() is called.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl8169_hw_reset() is called as part of the reset routine which is
scheduled in the line after. So we can remove the call to
rtl8169_hw_reset() here.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This helper is used only once, so remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to u32 filter, it is useful to know how many times
we reach each basic filter and how many times we pass the
ematch attached to it.

Sample output:

filter protocol arp pref 49152 basic chain 0
filter protocol arp pref 49152 basic chain 0 handle 0x1  (rule hit 3 success 3)
	action order 1: gact action pass
	 random type none pass val 0
	 index 1 ref 1 bind 1 installed 81 sec used 4 sec
	Action statistics:
	Sent 126 bytes 3 pkt (dropped 0, overlimits 0 requeues 0)
	backlog 0b 0p requeues 0

Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The only call site of sk_clone_lock is in inet_csk_clone_lock,
and sk_cookie will be set there.
So we don't need to set sk_cookie in sk_clone_lock().
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

remove unneeded semicolon
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/usb/rtl8150.c: In function 'read_bulk_callback':
drivers/net/usb/rtl8150.c:391:6: warning:
 variable 'rx_stat' set but not used [-Wunused-but-set-variable]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ioana Ciornei says:

====================
dpaa2-eth: add debugfs statistics

This patch set exports detailed driver counters through debugfs.
Counters which are already available through ethtool are now
presented in a structured manner (per-core, per-FQ and
per-channel) in debugfs.

The first patch is changing the dpaa2_eth_queue_count into a macro
(in order to avoid a warning) while the second one is adding the
debugfs support.

Changes in v2:
  - remove the _exit annotation of dpaa2_eth_dbg_exit
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Export detailed driver counters through debugfs.

Statistics already available in ethtool are presented in a
structured manner. Includes per-core, per-FQ and per-channel statistics.

Also transition from module_fsl_mc_driver to explicit module_init/exit
in order to create the debugfs directory besides registering the driver.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Transform dpaa2_eth_queue_count into a macro to follow the
the convention used by dpaa2_eth_fs_count and other functions.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
net: use strict checks in doit handlers

This series extends strict argument checking to doit handlers
of the GET* nature.  This is a bit tricky since strict checking
flag has already been released..

iproute2 did not have a release with strick checks enabled,
and it will only need a minor one-liner to pass strick checks
after all the work that DaveA has already done.

Big thanks to Dave Ahern for help and guidence.

v2:
 - remove unnecessary check in patch 5 (Nicolas);
 - add path 7 (DaveA);
 - improve messages in patch 8 (DaveA).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Make RTM_GETNETCONF's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make RTM_GETROUTE's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make RTM_GETADDRLABEL's doit handler use strict checks when
NETLINK_F_STRICT_CHK is set.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>