Sometimes ucc_geth fails to suspend with the following trace:

 ucc_geth e0103000.ucc: suspend
 ucc_geth e0102000.ucc: suspend
 NETDEV WATCHDOG: eth0 (ucc_geth): transmit queue 0 timed out
 ------------[ cut here ]------------
 Badness at net/sched/sch_generic.c:255
 NIP: c021cb5c LR: c021cb5c CTR: c01ab4b4
 [...]
 NIP [c021cb5c] dev_watchdog+0x298/0x2a8
 LR [c021cb5c] dev_watchdog+0x298/0x2a8
 Call Trace:
 [c0389da0] [c021cb5c] dev_watchdog+0x298/0x2a8 (unreliable)
 [c0389e00] [c0031ed8] run_timer_softirq+0x16c/0x1dc
 [c0389e50] [c002c638] __do_softirq+0xa4/0x11c
 [...]

This patch fixes the issue by properly detaching the device on
suspend, and attaching it back on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since hibernation assumes power loss, we should fully reinitialize
PHYs (including platform fixups), as if PHYs were just attached.

This patch factors phy_init_hw() out of phy_attach_direct(), then
converts mdio_bus to dev_pm_ops and adds an appropriate restore()
callback.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Sometimes kernel hangs on resume with the following trace:

 ucc_geth e0102000.ucc: resume
 INFO: task bash:1764 blocked for more than 120 seconds.
 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
 bash          D 0fecf43c     0  1764   1763 0x00000000
 Call Trace:
 [cf9a7c10] [c0012868] ret_from_except+0x0/0x14 (unreliable)
 --- Exception: cf9a7ce0 at __switch_to+0x4c/0x6c
     LR = 0xcf9a7cc0
 [cf9a7cd0] [c0008c14] __switch_to+0x4c/0x6c (unreliable)
 [cf9a7ce0] [c028bcfc] schedule+0x158/0x260
 [cf9a7d10] [c028c720] __mutex_lock_slowpath+0x80/0xd8
 [cf9a7d40] [c01cf388] phy_stop+0x20/0x70
 [cf9a7d50] [c01d514c] ugeth_resume+0x6c/0x13c
 [...]

Here is why.

On suspend:

- PM core starts suspending devices, ucc_geth_suspend gets called;

- ucc_geth calls phy_stop() on suspend. Note that phy_stop() is
  mostly asynchronous so it doesn't block ucc_geth's suspend routine,
  it just sets PHY_HALTED state and disables PHY's interrupts;

- Suddenly the state machine gets scheduled, it grabs the phydev->lock
  mutex and tries to process the PHY_HALTED state, so it calls
  phydev->adjust_link(phydev->attached_dev). In ucc_geth case
  adjust_link() calls msleep(), which reschedules the code flow back to
  PM core, which now finishes suspend and so we end up sleeping with
  phydev->lock mutex held.

On resume:

- PM core starts resuming devices (notice that nobody rescheduled
  the state machine yet, so the mutex is still held), the core calls
  ucc_geth's resume routine;

- ucc_geth_resume restarts the PHY with phy_stop()/phy_start()
  sequence, and the phy_*() calls are trying to grab the phydev->lock
  mutex. Here comes the deadlock.

This patch fixes the issue by stopping the state machine on suspend
and starting it again on resume.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This reverts commit 9bd568a5.

That commit is shown to cause allocation failures during initialization
on some machines.

http://bugzilla.kernel.org/show_bug.cgi?id=14844Signed-off-by: John W. Linville <linville@tuxdriver.com>

Allocate priv->rx_packets[IWM_RX_ID_HASH + 1] because the max array
index is IWM_RX_ID_HASH according to IWM_RX_ID_GET_HASH().

Cc: stable@kernel.org
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

`loop' reaches INIT_LOOP + 1 after the loop. so if ACX_INTR_INIT_COMPLETE
occurs in the last iteration the write occurs but also the error out as if a
timeout occurred. This is probably very unlikely to ever occur.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

mac80211 does not propagate failed hardware reconfiguration
requests. For suspend and resume this is important due to all
the possible issues that can come out of the suspend <-> resume
cycle. Not propagating the error means cfg80211 will assume
the resume for the device went through fine and mac80211 will
continue on trying to poke at the hardware, enable timers,
queue work, and so on for a device which is completley
unfunctional.

The least we can do is to propagate device start issues and
warn when this occurs upon resume. A side effect of this patch
is we also now propagate the start errors upon harware
reconfigurations (non-suspend), but this should also be desirable
anyway, there is not point in continuing to reconfigure a
device if mac80211 was unable to start the device.

For further details refer to the thread:

http://marc.info/?t=126151038700001&r=1&w=2

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When mac80211 suspends it calls a driver's suspend callback
as a last step and after that the driver assumes no calls will
be made to it until we resume and its start callback is kicked.
If such calls are made, however, suspend can end up throwing
hardware in an unexpected state and making the device unusable
upon resume.

Fix this by preventing mac80211 to schedule dynamic_ps_disable_work
by checking for when mac80211 starts to suspend and starts
quiescing. Frames should be allowed to go through though as
that is part of the quiescing steps and we do not flush the
mac80211 workqueue since it was already done towards the
beginning of suspend cycle.

The other mac80211 issue will be hanled in the next patch.

For further details see refer to the thread:

http://marc.info/?t=126144866100001&r=1&w=2

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

My previous change added in:

 commit 815833e7
    ath9k: fix tx status reporting

was not checking all possible tx error conditions. This could possibly
lead to throughput issues due to slow rate control adaption or missed
retransmissions of failed A-MPDU frames.

This patch adds a mask for all possible error conditions and uses it
in the xmit ok check.

Cc: stable@kernel.org
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

AMDPDU actions poke hardware for TX operation, as such
we want to turn hardware on for these actions. AMDPU RX operations
do not require hardware on as nothing is done in hardware for
those actions. Without this we cannot guarantee hardware has
been programmed correctly for each AMPDU TX action.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When we remove a IBSS/AP/Mesh interface we stop DMA
but to do this we should ensure hardware is on. Awaken
the device prior to these calls. This should ensure
DMA is stopped upon suspend and plain device removal.

Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Ensure the device is awake prior to trying to tell hardware
to stop it. Impact of not doing this is we can likely leave
the device in an undefined state likely causing issues with
suspend and resume. This patch ensures harware is where it
should be prior to suspend.

Cc: stable@kernel.org
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If there's an invalid channel or SSID, the code leaks
the scan request. Always free the scan request, unless
it was successfully given to the driver.
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is just a clean up and doesn't make a functional difference.  It keeps the
lint checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Kalle Valo <kalle.valo@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Joseph Nahmias reported, in http://bugs.debian.org/562016,
that he was getting the following warning (with some log
around the issue):

  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: direct probe responded
  ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: authenticated
  ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: RX AssocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
  ath0: associated
  ------------[ cut here ]------------
  WARNING: at net/wireless/mlme.c:97 cfg80211_send_rx_assoc+0x14d/0x152 [cfg80211]()
  Hardware name: 7658CTO
  ...
  Pid: 761, comm: phy0 Not tainted 2.6.32-trunk-686 #1
  Call Trace:
   [<c1030a5d>] ? warn_slowpath_common+0x5e/0x8a
   [<c1030a93>] ? warn_slowpath_null+0xa/0xc
   [<f86cafc7>] ? cfg80211_send_rx_assoc+0x14d/0x152
  ...
  ath0: link becomes ready
  ath0: deauthenticating from 00:11:95:77:e0:b0 by local choice (reason=3)
  ath0: no IPv6 routers present
  ath0: link is not ready
  ath0: direct probe to AP 00:11:95:77:e0:b0 (try 1)
  ath0: direct probe responded
  ath0: authenticate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: authenticated
  ath0: associate with AP 00:11:95:77:e0:b0 (try 1)
  ath0: RX ReassocResp from 00:11:95:77:e0:b0 (capab=0x421 status=0 aid=2)
  ath0: associated

It is not clear to me how the first "direct probe" here
happens, but this seems to be a race condition, if the
user requests to deauth after requesting assoc, but before
the assoc response is received. In that case, it may
happen that mac80211 tries to report the assoc success to
cfg80211, but gets blocked on the wdev lock that is held
because the user is requesting the deauth.

The result is that we run into a warning. This is mostly
harmless, but maybe cause an unexpected event to be sent
to userspace; we'd send an assoc success event although
userspace was no longer expecting that.

To fix this, remove the warning and check whether the
race happened and in that case abort processing.
Reported-by: Joseph Nahmias <joe@nahmias.net>
Cc: stable@kernel.org
Cc: 562016-quiet@bugs.debian.org
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This is a rt2870 based device.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The calibration period is now invoked by triggering a software
interrupt from within the ISR by ath5k_hw_calibration_poll()
instead of via a timer.

However, the calibration interval isn't initialized before
interrupts are enabled, so we can have a situation where an
interrupt occurs before the interval is assigned, so the
interval is actually negative.  As a result, the ISR will
arm a software interrupt to schedule the tasklet, and then
rearm it when the SWI is processed, and so on, leading to a
softlockup at modprobe time.

Move the initialization order around so the calibration interval
is set before interrupts are active.  Another possible fix
is to schedule the tasklet directly from the poll routine,
but I think there are additional plans for the SWI.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>

When fixed bssid is requested when joining an ibss network, incoming
beacons that match the configured bssid cause mac80211 to create new
sta entries, even before the ibss interface is in joined state.
When that happens, it fails to bring up the interface entirely, because
it checks for existing sta entries before joining.
This patch fixes this bug by refusing to create sta info entries before
the interface is fully operational.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

There is no reason to signal a carrier off when doing a 802.11 scan.

Cc: Holger Schurig <holgerschurig@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

orinoco_set_key is called from two places both with interrupts disabled
(under orinoco_lock). Use GFP_ATOMIC instead of GFP_KERNEL. Fixes following
warning:

[   77.254109] WARNING: at /home/bor/src/linux-git/kernel/lockdep.c:2465 lockdep_trace_alloc+0x9a/0xa0()
[   77.254109] Hardware name: PORTEGE 4000
[   77.254109] Modules linked in: af_packet irnet ppp_generic slhc ircomm_tty ircomm binfmt_misc dm_mirror dm_region_hash dm_log dm_round_robin dm_multipath dm_mod loop nvram toshiba cryptomgr aead pcompress crypto_blkcipher michael_mic crypto_hash crypto_algapi orinoco_cs orinoco cfg80211 smsc_ircc2 pcmcia irda toshiba_acpi yenta_socket video i2c_ali1535 backlight rsrc_nonstatic ali_agp pcmcia_core psmouse output crc_ccitt i2c_core alim1535_wdt rfkill sg evdev ohci_hcd agpgart usbcore pata_ali libata reiserfs [last unloaded: scsi_wait_scan]
[   77.254109] Pid: 2296, comm: wpa_supplicant Not tainted 2.6.32-1avb #1
[   77.254109] Call Trace:
[   77.254109]  [<c011f0ad>] warn_slowpath_common+0x6d/0xa0
[   77.254109]  [<c014206a>] ? lockdep_trace_alloc+0x9a/0xa0
[   77.254109]  [<c014206a>] ? lockdep_trace_alloc+0x9a/0xa0
[   77.254109]  [<c011f0f5>] warn_slowpath_null+0x15/0x20
[   77.254109]  [<c014206a>] lockdep_trace_alloc+0x9a/0xa0
[   77.254109]  [<c018d296>] __kmalloc+0x36/0x130
[   77.254109]  [<dffcb6a8>] ? orinoco_set_key+0x48/0x1c0 [orinoco]
[   77.254109]  [<dffcb6a8>] orinoco_set_key+0x48/0x1c0 [orinoco]
[   77.254109]  [<dffcb9fc>] orinoco_ioctl_set_encodeext+0x1dc/0x2d0 [orinoco]
[   77.254109]  [<c035b117>] ioctl_standard_call+0x207/0x3b0
[   77.254109]  [<dffcb820>] ? orinoco_ioctl_set_encodeext+0x0/0x2d0 [orinoco]
[   77.254109]  [<c0307f1f>] ? rtnl_lock+0xf/0x20
[   77.254109]  [<c0307f1f>] ? rtnl_lock+0xf/0x20
[   77.254109]  [<c02fb115>] ? __dev_get_by_name+0x85/0xb0
[   77.254109]  [<c035b616>] wext_handle_ioctl+0x176/0x200
[   77.254109]  [<dffcb820>] ? orinoco_ioctl_set_encodeext+0x0/0x2d0 [orinoco]
[   77.254109]  [<c030020f>] dev_ioctl+0x6af/0x730
[   77.254109]  [<c02eec65>] ? move_addr_to_kernel+0x55/0x60
[   77.254109]  [<c02eed59>] ? sys_sendto+0xe9/0x130
[   77.254109]  [<c02ed77e>] sock_ioctl+0x7e/0x250
[   77.254109]  [<c02ed700>] ? sock_ioctl+0x0/0x250
[   77.254109]  [<c019cf4c>] vfs_ioctl+0x1c/0x70
[   77.254109]  [<c019d1fa>] do_vfs_ioctl+0x6a/0x590
[   77.254109]  [<c0178e50>] ? might_fault+0x90/0xa0
[   77.254109]  [<c0178e0a>] ? might_fault+0x4a/0xa0
[   77.254109]  [<c02ef90e>] ? sys_socketcall+0x17e/0x280
[   77.254109]  [<c019d759>] sys_ioctl+0x39/0x60
[   77.254109]  [<c0102e3b>] sysenter_do_call+0x12/0x32
[   77.254109] ---[ end trace 95ef563548d21efd ]---
Signed-off-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

 net/xfrm/xfrm_policy.c |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
Signed-off-by: David S. Miller <davem@davemloft.net>

A few lines earlier we assume that best->slave could be either null or non-null so
we should check it here as well.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f001fde5 changed
net_device.dev_addr from a 32-byte array to a pointer.

I found 4 ethernet drivers which rely on sizeof(dev_addr), which are now
only copying 4 bytes of the address information on 32bit systems.

Fix them to use ETH_ALEN.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Reviewed-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The gfar_select_queue() function was used to set queue mapping
only for forwarding/bridging applications and the condition
for locally generated packets was completely ignored.

The solution is to remove the gfar_select_queue() function and
use skb_record_rx_queue to set queue mapping for
forwarding/bridging applications. This will ensure that in case of
forwarding/bridging applications txq = rxq will be selected and
skb_tx_hash will be used to pick up a txq for locally generated packets.
Signed-off-by: Sandeep Gopalpet <Sandeep.Kumar@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Using macro tun_sk is more clear and shorter. However tun.c has tun_sk,
but doesn't use it.
Signed-off-by: Vitaliy Gusev <vgusev@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

If PHY doesn't have an IRQ, phylib would poll for link changes, and
would call adjust_link() every second. In that case we disable and
enable the controller every second.

Let's better check if there is actually anything changed, and, if so,
change the MAC settings.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 864fdf88 ("ucc_geth:
Fix hangs after switching from full to half duplex") ucc_geth driver
disables the controller during MAC configuration changes. Though,
disabling the controller might take quite awhile, and so the netdev
watchdog might get upset:

 NETDEV WATCHDOG: eth2 (ucc_geth): transmit queue 0 timed out
 ------------[ cut here ]------------
 Badness at c02729a8 [verbose debug info unavailable]
 NIP: c02729a8 LR: c02729a8 CTR: c01b6088
 REGS: c0451c40 TRAP: 0700   Not tainted  (2.6.32-trunk-8360e)
 [...]
 NIP [c02729a8] dev_watchdog+0x280/0x290
 LR [c02729a8] dev_watchdog+0x280/0x290
 Call Trace:
 [c0451cf0] [c02729a8] dev_watchdog+0x280/0x290 (unreliable)
 [c0451d50] [c00377c4] run_timer_softirq+0x164/0x224
 [c0451da0] [c0032a38] __do_softirq+0xb8/0x13c
 [c0451df0] [c00065cc] do_softirq+0xa0/0xac
 [c0451e00] [c003280c] irq_exit+0x7c/0x9c
 [c0451e10] [c00640c4] __ipipe_sync_stage+0x248/0x24c
 [...]

This patch fixes the issue by detaching the netdev during the
time we change the configuration.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>

Following oops was seen with the ucc_geth driver:

 Unable to handle kernel paging request for data at address 0x00000058
 Faulting instruction address: 0xc024f2fc
 Oops: Kernel access of bad area, sig: 11 [#1]
 [...]
 NIP [c024f2fc] skb_recycle_check+0x14/0x100
 LR [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
 Call Trace:
 [df857d50] [c000b03c] __ipipe_grab_irq+0x3c/0xa4 (unreliable)
 [df857d60] [e30aa0a4] ucc_geth_poll+0xd8/0x4e0 [ucc_geth_driver]
 [df857dd0] [c0258cf8] net_rx_action+0xf8/0x1b8
 [df857e10] [c0032a38] __do_softirq+0xb8/0x13c
 [df857e60] [c00065cc] do_softirq+0xa0/0xac
 [...]

This is because ucc_geth_tx() tries to process an empty queue when
queues are logically stopped. Stopping the queues doesn't disable
polling, and since nowadays ucc_geth_tx() is actually called from
the polling routine, the oops above might pop up.

Fix this by removing 'netif_queue_stopped() == 0' check.
Reported-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Tested-by: Lennart Sorensen <lsorense@csclub.uwaterloo.ca>
Cc: Stable <stable@vger.kernel.org> [2.6.32]
Signed-off-by: David S. Miller <davem@davemloft.net>

Use DMA_BIT_MASK instead of plain values.
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

when using policy routing and the skb mark:
there are cases where a back path validation requires us
to use a different routing table for src ip validation than
the one used for mapping ingress dst ip.
One such a case is transparent proxying where we pretend to be
the destination system and therefore the local table
is used for incoming packets but possibly a main table would
be used on outbound.
Make the default behavior to allow the above and if users
need to turn on the symmetry via sysctl src_valid_mark
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the device is reset during MTU change, ring size change, or self
test, etc, the cnic status block needs to be properly initialized if
cnic is registered.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This updates pktgen so that it does not decrement skb->users
when it receives valid NET_XMIT_xxx values.  These are now
valid return values from ndo_start_xmit in net-next-2.6.
They also indicate the skb has been consumed.

This fixes pktgen to work correctly with vlan devices.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There are BUGs "scheduling while atomic" triggered by the timer
rhine_tx_timeout(). They are caused by calling napi_disable() (with
msleep()). This patch fixes it by moving most of the timer content to
the workqueue function (similarly to other drivers, like tg3), with
spin_lock() changed to BH version.

Additionally, there is spin_lock_irq() moved in rhine_close() to
exclude napi_disable() etc., also tg3's way.
Reported-by: Andrey Rahmatullin <wrar@altlinux.org>
Tested-by: Andrey Rahmatullin <wrar@altlinux.org>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds a pci_save_state() call in ixgbe_resume() after
pci_restore_state(). A similar change was made in ixgbe_io_slot_reset()
that accommodates pci_restore_state() new behavior. This change makes
pci_restore_state() clear the saved_state flag This is necessary due
to a resent kernel change to pci_restore_state() so that it now clears
the saved_state flag of the device right after the device.s standard
configuration registers have been poplulated with the previously saved
values.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Changes to return correct values for transceiver and supported in
ethtool get_settings function.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

NIC controller has to be set to an appropriate mode before doing a loopback
test. Test will fail otherwise.
Signed-off-by: Sarveshwar Bandi <sarveshwarb@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>