Conflicts (resolved):
	arch/x86/configs/x86_64_defconfig
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: defconfig change

Enable MCE in the 32-bit defconfig.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: defconfig change

Enable MCE in the 64-bit defconfig.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Impact: Fix marginal race condition

One the first CPU the machine checks are enabled early before
the local APIC is enabled. This could in theory lead
to some lost CMCI events very early during boot because
CMCIs cannot be delivered with disabled LAPIC.

The poller also doesn't recover from this because it doesn't
check CMCI banks.

Add an explicit CMCI banks check after the LAPIC is enabled.
This is only done for CPU #0, the other CPUs only initialize
machine checks after the LAPIC is on.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: Avoids confusing other OSes.

Disable the CMCI vector on reboot to avoid confusing other OS.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: Bug fix on UP

The MCE code is reinitialized from resume, so we can't use
__cpuinit/__cpuexit for most of the code.  Remove those annotations
for anything downstream of mce_init().
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: Major new feature

Intel CMCI (Corrected Machine Check Interrupt) is a new
feature on Nehalem CPUs. It allows the CPU to trigger
interrupts on corrected events, which allows faster
reaction to them instead of with the traditional
polling timer.

Also use CMCI to discover shared banks. Machine check banks
can be shared by CPU threads or even cores. Using the CMCI enable
bit it is possible to detect the fact that another CPU already
saw a specific bank. Use this to assign shared banks only
to one CPU to avoid reporting duplicated events.

On CPU hot unplug bank sharing is re discovered. This is done
using a thread that cycles through all the CPUs.

To avoid races between the poller and CMCI we only poll
for banks that are not CMCI capable and only check CMCI
owned banks on a interrupt.

The shared banks ownership information is currently only used for
CMCI interrupts, not polled banks.

The sharing discovery code follows the algorithm recommended in the
IA32 SDM Vol3a 14.5.2.1

The CMCI interrupt handler just calls the machine check poller to
pick up the machine check event that caused the interrupt.

I decided not to implement a separate threshold event like
the AMD version has, because the threshold is always one currently
and adding another event didn't seem to add any value.

Some code inspired by Yunhong Jiang's Xen implementation,
which was in term inspired by a earlier CMCI implementation
by me.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: New register definitions only

CMCI means support for raising an interrupt on a corrected machine
check event instead of having to poll for it. It's a new feature in
Intel Nehalem CPUs available on some machine check banks.

For details see the IA32 SDM Vol3a 14.5

Define the registers for it as a preparation for further patches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Define a per cpu bitmap that contains the banks polled by the machine
check poller. This is needed for the CMCI code in the next patches
to be able to disable polling on specific banks.

The bank by default contains all banks, so there is no behaviour
change. Only future code will remove some banks from the polling
set.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: behavior change, use common code

Use a standard leaky bucket ratelimit for the machine check
warning print interval instead of waiting every check_interval.
Also decrease the limit to twice per minute.
This interacts better with threshold interrupts because
they can happen more often than check_interval.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: minor bugfix

The threshold handler on AMD (and soon on Intel) could be theoretically
reentered by the hardware. This could lead to corrupted events
because the machine check poll code assumes it is not reentered.

Move the APIC ACK to the end of the interrupt handler to let
the hardware avoid that.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: cleanup; preparation for feature

The mce_amd_64 code has an own private MC threshold vector with an own
interrupt handler. Since Intel needs a similar handler
it makes sense to share the vector because both can not
be active at the same time.

I factored the common APIC handler code into a separate file which can
be used by both the Intel or AMD MC code.

This is needed for the next patch which adds an Intel specific
CMCI handler.

This patch should be a nop for AMD, it just moves some code
around.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: Cleanup (code movement)

Move MAX_NR_BANKS into mce.h because it's needed there
for followup patches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>

Impact: Bug fix when CPU hotplug is disabled

Correct the following broken __cpuinit/__cpuexit annotations:

- mce_cpu_features() is called from mce_resume(), and so cannot be
  __cpuinit.
- mce_disable_cpu() and mce_reenable_cpu() are called from
  mce_cpu_callback(), and so cannot be __cpuexit().

Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>

Add missing parameter value to list of available values
for acpi=<value>.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
  drm/i915: Add missing mutex_lock(&dev->struct_mutex)
  drm/i915: fix WC mapping in non-GEM i915 code.
  drm/i915: Fix regression in 95ca9d
  drm/i915: Retire requests from i915_gem_busy_ioctl.
  drm/i915: suspend/resume GEM when KMS is active
  drm/i915: Don't let a device flush to prepare buffers clear new write_domains.
  drm/i915: Cut two args to set_to_gpu_domain that confused this tricky path.

there might be a nicer way to fix this but this is the simplest for now.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>

[airlied - taken from mailing list posting]
Signed-off-by: Dave Airlie <airlied@redhat.com>

The object is dereferenced before the NULL check. Oops.

Fixes http://bugs.freedesktop.org/show_bug.cgi?id=20235Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This ensures that the user gets the latest information from the hardware
on whether the buffer is busy, potentially reducing the working set of objects
that the user chooses.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

In the KMS case, we need to suspend/resume GEM as well.  So on suspend, make
sure we idle GEM and stop any new rendering from coming in, and on resume,
re-init the framebuffer and clear the suspended flag.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The problem was that object_set_to_gpu_domain would set the new write_domains
that are getting set by this batchbuffer, then the accumulated flushes required
for all the objects in preparation for this batchbuffer were posted, and the
brand new write domain would get cleared by the flush being posted.  Instead,
hang on to the new (or old if we're not changing it) value and set it after
the flush is queued.

Results from this noticably included conformance test failures from reads
shortly after writes (where the new write domain had been lost and thus not
flushed and waited on), but is a suspected cause of hangs in some apps when
a write domain is lost on a buffer that gets reused for instruction or
commmand state.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

While not strictly required, it helped while thinking about the following
change.  This change should be invariant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>

At some point we (okay, I) managed to break the ability for users to use the
setsockopt() syscall to set IPv4 options when NetLabel was not active on the
socket in question.  The problem was noticed by someone trying to use the
"-R" (record route) option of ping:

 # ping -R 10.0.0.1
 ping: record route: No message of desired type

The solution is relatively simple, we catch the unlabeled socket case and
clear the error code, allowing the operation to succeed.  Please note that we
still deny users the ability to override IPv4 options on socket's which have
NetLabel labeling active; this is done to ensure the labeling remains intact.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

The CIPSO protocol engine incorrectly stated that the FIPS-188 specification
could be found in the kernel's Documentation directory.  This patch corrects
that by removing the comment and directing users to the FIPS-188 documented
hosted online.  For the sake of completeness I've also included a link to the
CIPSO draft specification on the NetLabel website.

Thanks to Randy Dunlap for spotting the error and letting me know.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>

* 'core/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  PM: Split up sysdev_[suspend|resume] from device_power_[down|up], fix

Impact: module build fix

Fix:

 ERROR: "sysdev_resume" [arch/x86/kernel/apm.ko] undefined!
 ERROR: "sysdev_suspend" [arch/x86/kernel/apm.ko] undefined!

As these APIs are now used by the APM driver, which can be built
as a module.

Also fix a few extra (and inconsistent) newlines in comment blocks
preceding these functions.
Signed-off-by: Ingo Molnar <mingo@elte.hu>

The kernel-api docbook was much larger than any of the others,
so processing it took longer and needed some docbook extras in
some cases, so split it into kernel-api (infrastructure etc.)
and device drivers/device subsystems.  This allows these docbooks
to be generated in parallel.  (This reduced the docbook processing
time on my 4-proc system with make -j4 from about 5min:16sec to
about 2min:01sec.)

The chapters that were moved from kernel-api to device-drivers are:

Driver Basics
Device drivers infrastructure
Parallel Port Devices
Message-based devices
Sound Devices
16x50 UART Driver
Frame Buffer Library
Input Subsystem
Serial Peripheral Interface (SPI)
I2C and SMBus Subsystem
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Move the sysdev_suspend/resume from the callee to the callers, with
no real change in semantics, so that we can rework the disabling of
interrupts during suspend/hibernation.

This is based on an earlier patch from Linus.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Right now nobody cares, but the suspend/resume code will eventually want
to suspend device interrupts without suspending the timer, and will
depend on this flag to know.

The modern x86 timer infrastructure uses the local APIC timers and never
shows up as a device interrupt at all, so it isn't affected and doesn't
need any of this.

Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI: remove CONFIG_ACPI_SYSTEM
  fujitsu-laptop: Use RFKILL support bitmask from firmware
  x86_64: Fix S3 fail path
  x86_64: acpi/wakeup_64 cleanup
  battery: don't assume we are fully charged when not charging or discharging
  ACPI: EC: Add delay for slow MSI controller

Fix descriptions of device attributes to be consistent with the actual
implementations in include/linux/device.h

Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Fix the presented definition of struct device_attribute to match the
actual definition in include/linux/device.h

Signed-off-by: Mike Murphy <mamurph[at]cs.clemson.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

http://kisskb.ellerman.id.au/kisskb/buildresult/72115/:
| net/mac80211/ieee80211_i.h:327: error: syntax error before 'volatile'
| net/mac80211/ieee80211_i.h:350: error: syntax error before '}' token
| net/mac80211/ieee80211_i.h:455: error: field 'sta' has incomplete type
| distcc[19430] ERROR: compile net/mac80211/main.c on sprygo/32 failed

This is caused by

| # define mfp ((*(volatile struct MFP*)MFP_BAS))

in arch/m68k/include/asm/atarihw.h, which conflicts with the new "mfp" enum in
net/mac80211/ieee80211_i.h.

Rename "mfp" to "st_mfp", as it's a way too generic name for a global #define.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Remove CONFIG_ACPI_SYSTEM.  It was always set the same as CONFIG_ACPI,
and it had no menu label, so there was no way to set it to anything
other than "y".

Some things under CONFIG_ACPI_SYSTEM (acpi_irq_handled, acpi_os_gpe_count(),
event_is_open, register_acpi_notifier(), etc.) are used unconditionally
by the CA, the OSPM, and drivers, so we depend on them always being
present.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Len Brown <len.brown@intel.com>

Up until now, we polled the rfkill status for every incoming FUJ02E3 ACPI event.
It turns out that the firmware has a bitmask which indicates what rfkill-related
state it can report.
The rfkill_supported bitmask is now used to avoid polling for rfkill at all in
the notification handler if there is no support. Also, it is used in the platform
device callbacks. As before we register all callbacks and report "unknown" if the
firmware does not give us status updates for that particular bit.

This was fed through checkpatch.pl and tested on the S6420, S7020 and P8010
platforms.
Signed-off-by: Tony Vroon <tony@linx.net>
Tested-by: Stephen Gildea <stepheng+linux@gildea.com>
Acked-by: Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
Signed-off-by: Len Brown <len.brown@intel.com>

As acpi_enter_sleep_state can fail, take this into account in
do_suspend_lowlevel and don't return to the do_suspend_lowlevel's
caller. This would break (currently) fpu status and preempt count.

Technically, this means use `call' instead of `jmp' and `jmp' to
the `resume_point' after the `call' (i.e. if
acpi_enter_sleep_state returns=fails). `resume_point' will handle
the restore of fpu and preempt count gracefully.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>