Make AF_KCM sendmsg() support MSG_SPLICE_PAGES.  This causes pages to be
spliced from the source iterator if possible.

This allows ->sendpage() to be replaced by something that can handle
multiple multipage folios in a single transaction.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Tom Herbert <tom@herbertland.com>
cc: Tom Herbert <tom@quantonium.net>
cc: Cong Wang <cong.wang@bytedance.com>
cc: Jens Axboe <axboe@kernel.dk>
cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Saeed Mahameed says:

====================
mlx5-updates-2023-05-31

net/mlx5: Support 4 ports VF LAG, part 1/2

This series continues the series[1] "Support 4 ports HCAs LAG mode"
by Mark Bloch. This series adds support for 4 ports VF LAG (single FDB
E-Switch).

This series of patches focuses on refactoring different sections of the
code that make assumptions about VF LAG supporting only two ports. For
instance, it assumes that each device can only have one peer.

Patches 1-5:
- Refactor ETH handling of TC rules of eswitches with peers.
Patch 6:
- Refactors peer miss group table.
Patches 7-9:
- Refactor single FDB E-Switch creation.
Patch 10:
- Refactor the DR layer.
Patches 11-14:
- Refactors devcom layer.

Next series will refactor LAG layer and enable 4 ports VF LAG.
This series specifically allows HCAs with 4 ports to create a VF LAG
with only 4 ports. It is not possible to create a VF LAG with 2 or 3
ports using HCAs that have 4 ports.

Currently, the Merged E-Switch feature only supports HCAs with 2 ports.
However, upcoming patches will introduce support for HCAs with 4 ports.

In order to activate VF LAG a user can execute:

devlink dev eswitch set pci/0000:08:00.0 mode switchdev
devlink dev eswitch set pci/0000:08:00.1 mode switchdev
devlink dev eswitch set pci/0000:08:00.2 mode switchdev
devlink dev eswitch set pci/0000:08:00.3 mode switchdev
ip link add name bond0 type bond
ip link set dev bond0 type bond mode 802.3ad
ip link set dev eth2 master bond0
ip link set dev eth3 master bond0
ip link set dev eth4 master bond0
ip link set dev eth5 master bond0

Where eth2, eth3, eth4 and eth5 are net-interfaces of pci/0000:08:00.0
pci/0000:08:00.1 pci/0000:08:00.2 pci/0000:08:00.3 respectively.

User can verify LAG state and type via debugfs:
/sys/kernel/debug/mlx5/0000\:08\:00.0/lag/state
/sys/kernel/debug/mlx5/0000\:08\:00.0/lag/type

[1]
https://lore.kernel.org/netdev/20220510055743.118828-1-saeedm@nvidia.com/

* tag 'mlx5-updates-2023-05-31' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Devcom, extend mlx5_devcom_send_event to work with more than two devices
  net/mlx5: Devcom, introduce devcom_for_each_peer_entry
  net/mlx5: E-switch, mark devcom as not ready when all eswitches are unpaired
  net/mlx5: Devcom, Rename paired to ready
  net/mlx5: DR, handle more than one peer domain
  net/mlx5: E-switch, generalize shared FDB creation
  net/mlx5: E-switch, Handle multiple master egress rules
  net/mlx5: E-switch, refactor FDB miss rule add/remove
  net/mlx5: E-switch, enlarge peer miss group table
  net/mlx5e: Handle offloads flows per peer
  net/mlx5e: en_tc, re-factor query route port
  net/mlx5e: rep, store send to vport rules per peer
  net/mlx5e: tc, Refactor peer add/del flow
  net/mlx5e: en_tc, Extend peer flows to a list
====================

Link: https://lore.kernel.org/r/20230602191301.47004-1-saeed@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Andrzej Hajda says:

====================
drm/i915: use ref_tracker library for tracking wakerefs

This is reviewed series of ref_tracker patches, ready to merge
via network tree, rebased on net-next/main.
i915 patches will be merged later via intel-gfx tree.
====================

Merge on top of an -rc tag in case it's needed in another tree.

Link: https://lore.kernel.org/r/20230224-track_gt-v9-0-5b47a33f55d1@intel.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Library can handle allocation failures. To avoid allocation warnings
__GFP_NOWARN has been added everywhere. Moreover GFP_ATOMIC has been
replaced with GFP_NOWAIT in case of stack allocation on tracker free
call.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Similar to stack_(depot|trace)_snprint the patch
adds helper to printing stats to memory buffer.
It will be helpful in case of debugfs.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

In case the library is tracking busy subsystem, simply
printing stack for every active reference will spam log
with long, hard to read, redundant stack traces. To improve
readabilty following changes have been made:
- reports are printed per stack_handle - log is more compact,
- added display name for ref_tracker_dir - it will differentiate
  multiple subsystems,
- stack trace is printed indented, in the same printk call,
- info about dropped references is printed as well.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

To have reliable detection of leaks, caller must be able to check under
the same lock both: tracked counter and the leaks. dir.lock is natural
candidate for such lock and unlocked print helper can be called with this
lock taken.
As a bonus we can reuse this helper in ref_tracker_dir_exit.
Signed-off-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says:

====================
mlxsw, selftests: Cleanups

This patchset consolidates a number of disparate items that can all be
considered cleanups. They are all related to mlxsw in that they are
directly in mlxsw code, or in selftests that mlxsw heavily uses.

- patch #1 fixes a comment, patch #2 propagates an extack

- patches #3 and #4 tweak several loops to query a resource once and cache
  in a local variable instead of querying on each iteration

- patches #5 and #6 fix selftest diagrams, and #7 adds a missing diagram
  into an existing test

- patch #8 disables a PVID on a bridge in a selftest that should not need
  said PVID
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When everything is configured, VLAN membership on the bridge in this
selftest are as follows:

    # bridge vlan show
    port              vlan-id
    swp2              1 PVID Egress Untagged
                      555
    br1               1 Egress Untagged
                      555 PVID Egress Untagged

Note that it is possible for untagged traffic to just flow through as VLAN
1, instead of using VLAN 555 as intended by the test. This configuration
seems too close to "works by accident", and it would be better to just shut
out VLAN 1 altogether.

To that end, configure vlan_default_pvid of 0:

    # bridge vlan show
    port              vlan-id
    swp2              555
    br1               555 PVID Egress Untagged
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a topology diagram to this selftest to make the configuration easier to
understand.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The topology diagram implies that $swp1 and $swp2 are members of the bridge
br0, when in fact only their uppers, $swp1.10 and $swp2.10 are. Adjust the
diagram.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The topology diagram implies that $swp1 and $swp2 are members of the bridge
br0, when in fact only their uppers, $swp1.10 and $swp2.10 are. Adjust the
diagram.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MLXSW_CORE_RES_GET involves a call to spectrum_core, a separate module.
Instead of making the call on every iteration, cache it up front, and use
the value.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

MLXSW_CORE_RES_GET involves a call to spectrum_core, a separate module.
Instead of making the call on every iteration, cache it up front, and use
the value.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In commit 26029225 ("mlxsw: spectrum_router: Propagate extack
further"), the mlxsw_sp_rif_ops.configure callback got a new argument,
extack. However the callbacks that deal with tunnel configuration,
mlxsw_sp1_rif_ipip_lb_configure() and mlxsw_sp2_rif_ipip_lb_configure(),
were never updated to pass the parameter further. Do that now.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

"Reserved for X" usually means that only X is supposed to use a given
object. Here, it is used in the sense that X should consider the object
"reserved", as in "restricted".

Replace the comment simply by "X", with the implication that that's where
the field is used.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Amit Cohen <amcohen@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Russell King says:

====================
convert sja1105 xpcs creation and remove xpcs_create

This series of three patches converts sja1105 to use the newly
provided xpcs_create_mdiodev(), and as there become no users of
xpcs_create(), removes this function from the global namespace to
discourage future direct use.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

There are now no callers of xpcs_create(), so let's remove it from
public view to discourage future direct usage.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new xpcs_create_mdiodev() creator, which simplifies the
creation and destruction of the mdio device associated with xpcs.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Put the mdiodev after xpcs_create() so that the XPCS driver can manage
the lifetime of the mdiodev its using.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Maxime Chevallier says:

====================
net: add a regmap-based mdio driver and drop TSE PCS

This is the V4 of a series that follows-up on the work [1] aiming to drop the
altera TSE PCS driver, as it turns out to be a version of the Lynx PCS exposed
as a memory-mapped block, instead of living on an MDIO bus.

One step of this removal involved creating a regmap-based mdio driver
that translates MDIO accesses into the actual underlying bus that
exposes the register. The register layout must of course match the
standard MDIO layout, but we can now account for differences in stride
with recent work on the regmap subsystem [2].

Sorry for repeating this, but I didn't hear anything on this matter in previous
iterations, Mark, Net maintainers, this series depends on the patch
e12ff287 that was recently merged into the regmap tree [3].

For this series to be usable in net-next, this patch must be applied
beforehand. Should Mark create a tag that would then be merged into
net-next ? Or should we just wait for the next release to merge this
into net-next ?

This series introduces a new MDIO driver, and uses it to convert Altera
TSE from the actual TSE PCS driver to Lynx PCS.

Since it turns out dwmac_socfpga also uses a TSE PCS block, port that
driver to Lynx as well.

Changes in V4 :
 - Use new pcs_lynx_create/destroy helpers added by Russell
 - Rework the cleanup sequence to avoid leaking data
 - Rework a bit KConfig to properly select dependencies
 - Fix a few hiccups with misplaced hunks in 2 commits

Changes in V3 :
 - Use a dedicated struct for the mii bus's priv data, to avoid
   duplicating the whole struct mdio_regmap_config, from which 2 fields
   only are necessary after init, as suggested by Russell
 - Use ~0 instead of ~0UL for the no-scan bitmask, following Simon's
   review.

Changes in V2 :
 - Use phy_mask to avoid unnecessarily scanning the whole mdio bus
 - Go one step further and completely disable scanning if users
   set the .autoscan flag to false, in case the mdiodevice isn't an
   actual PHY (a PCS for example).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

dwmac_socfpga re-implements support for the TSE PCS, which is identical
to the already existing TSE PCS, which in turn is the same as the Lynx
PCS. Drop the existing TSE re-implemenation and use the Lynx PCS
instead, relying on the regmap-mdio driver to translate MDIO accesses
into mmio accesses.

Add a lynx_pcs reference in the stmmac's internal structure, and use
.mac_select_pcs() to return the relevant PCS to be used.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that we can easily create a mdio-device that represents a
memory-mapped device that exposes an MDIO-like register layout, we don't
need the Altera TSE PCS anymore, since we can use the Lynx PCS instead.
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The newly introduced regmap-based MDIO driver allows for an easy mapping
of an mdiodevice onto the memory-mapped TSE PCS, which is actually a
Lynx PCS.

Convert Altera TSE to use this PCS instead of the pcs-altera-tse, which
is nothing more than a memory-mapped Lynx PCS.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There exists several examples today of devices that embed an ethernet
PHY or PCS directly inside an SoC. In this situation, either the device
is controlled through a vendor-specific register set, or sometimes
exposes the standard 802.3 registers that are typically accessed over
MDIO.

As phylib and phylink are designed to use mdiodevices, this driver
allows creating a virtual MDIO bus, that translates mdiodev register
accesses to regmap accesses.

The reason we use regmap is because there are at least 3 such devices
known today, 2 of them are Altera TSE PCS's, memory-mapped, exposed
with a 4-byte stride in stmmac's dwmac-socfpga variant, and a 2-byte
stride in altera-tse. The other one (nxp,sja1110-base-tx-mdio) is
exposed over SPI.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This following message is printed in the console each time a network
device configured with an IPv6 addresses is ready to be used:

  ADDRCONF(NETDEV_CHANGE): <iface>: link becomes ready

When netns are being extensively used -- e.g. by re-creating netns' with
veth to discuss with each others for testing purposes like mptcp_join.sh
selftest does -- it generates a lot of messages like that: more than 700
when executing mptcp_join.sh with the latest version.

It looks like this message is not that helpful after all: maybe it can
be used as a sign to know if there is something wrong, e.g. if a device
is being regularly reconfigured by accident? But even then, there are
better ways to monitor and diagnose such issues.

When looking at commit 3c21edbd ("[IPV6]: Defer IPv6 device
initialization until the link becomes ready.") which introduces this new
message, it seems it had been added to verify that the new feature was
working as expected. It could have then used a lower level than "info"
from the beginning but it was fine like that back then: 17 years ago.

It seems then OK today to simply lower its level, similar to commit
7c62b8dd ("net/ipv6: lower the level of "link is not ready" messages")
and as suggested by Mat [1], Stephen and David [2].

Link: https://lore.kernel.org/mptcp/614e76ac-184e-c553-af72-084f792e60b0@kernel.org/T/ [1]
Link: https://lore.kernel.org/netdev/68035bad-b53e-91cb-0e4a-007f27d62b05@tessares.net/T/ [2]
Suggested-by: Mat Martineau <martineau@kernel.org>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Suggested-by: David Ahern <dsahern@kernel.org>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dan Carpenter reported a signedness bug in genphy_loopback(). Andrew
reports that:

"It is common to get this wrong in general with PHY drivers. Dan
regularly posts fixes like this soon after a PHY driver patch it
merged. I really wish we could somehow get the compiler to warn when
the result from phy_read() is stored into a unsigned type. It would
save Dan a lot of work."

Let's make phy_read*_poll_timeout() immune to further issues when "val"
is an unsigned type by storing the read function's result in a signed
int as well as "val", and using the signed variable both to check for
an error and for propagating that error to the caller.

The advantage of this method is we don't change where the cast from
the signed return code to the user's variable occurs - so users will
see no change.

Previously Heiner changed phy_read_poll_timeout() to check for an error
before evaluating the user supplied condition, but didn't update
phy_read_mmd_poll_timeout(). Make that change there too.

Link: https://lore.kernel.org/r/d7bb312e-2428-45f6-b9b3-59ba544e8b94@kili.mountainSigned-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1q4kX6-00BNuM-Mx@rmk-PC.armlinux.org.ukSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Jakub Kicinski says:

====================
tools: ynl-gen: dust off the user space code

Every now and then I wish I finished the user space part of
the netlink specs, Python scripts kind of stole the show but
C is useful for selftests and stuff which needs to be fast.
Recently someone asked me how to access devlink and ethtool
from C++ which pushed me over the edge.

Fix things which bit rotted and finish notification handling.
This series contains code gen changes only. I'll follow up
with the fixed component, samples and docs as soon as it's
merged.
====================

Link: https://lore.kernel.org/r/20230602023548.463441-1-kuba@kernel.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Notifications may come in at any time. The family must be always
ready to parse a random incoming notification. Generate notification
table for parsing and tell YNL which request we're processing
to distinguish responses from notifications.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We'll want to store static info about the family soon.
Generate a struct. This changes creation from, e.g.:

	 ys = ynl_sock_create("netdev", &yerr);
to:
	 ys = ynl_sock_create(&ynl_netdev_family, &yerr);

on user's side.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We expect user to allocate requests with calloc(),
make things a bit more consistent and provide helpers.
Generate free calls, too.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

We generate send() and recv() calls and all msg handling for
each operation. It's a lot of repeated code and will only grow
with notification handling. Call back to a helper YNL lib instead.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

It's sometimes useful to print the name of an enum value,
flag or name of the op. Python can do it, add C helper
code gen for getting names of things.

Example:

  static const char * const netdev_xdp_act_strmap[] = {
	[0] = "basic",
	[1] = "redirect",
	[2] = "ndo-xmit",
	[3] = "xsk-zerocopy",
	[4] = "hw-offload",
	[5] = "rx-sg",
	[6] = "ndo-xmit-sg",
  };

  const char *netdev_xdp_act_str(enum netdev_xdp_act value)
  {
	value = ffs(value) - 1;
	if (value < 0 || value >= (int)MNL_ARRAY_SIZE(netdev_xdp_act_strmap))
		return NULL;
	return netdev_xdp_act_strmap[value];
  }
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Parsing nested types may return an error, propagate it.
Not marking as a fix, because nothing uses YNL upstream.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Both event and notify types are always consistent. Rewrite
the condition checking if we can reuse reply types to be
less picky and let notify thru.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

For pure structs (parsed nested attributes) we track what
forms of the struct exist in request and reply directions.
Make sure we don't overwrite the recorded struct each time,
otherwise the information is lost.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Unused and Pad attributes don't carry information.
Unused should never exist, and be rejected.
Pad should be silently skipped.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Make sure all relevant headers are included, we allocate memory,
use memcpy() and Linux types without including the headers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlx5_devcom_send_event is used to send event from one eswitch to the
other. In other words, only one event is sent, which means, no error
mechanism is needed.
However, In case devcom have more than two eswitches, a proper error
mechanism is needed. Hence, in case of error, devcom will perform the
error unwind, since devcom knows how many events were successful.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Introduce generic APIs which will retrieve all peers.
This API replace mlx5_devcom_get/release_peer_data which retrieve
only a single peer.
Signed-off-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Vlad Buslov <vladbu@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>