Currently qcaspi_netdev_setup accidentally clears IFF_BROADCAST.
So fix this by keeping the flags from ether_setup.
Reported-by: Michael Heimpold <michael.heimpold@i2se.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 291ab06e (net: qualcomm: new Ethernet over SPI driver for QCA7000)
Signed-off-by: David S. Miller <davem@davemloft.net>

Nik pointed that the VRF driver should be using skb_header_pointer
instead of accessing skb->data and bits beyond directly which can
be garbage.

Fixes: 35402e31 ("net: Add IPv6 support to VRF device")
Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The JMC260 network card fails to suspend/resume because the call to
jme_start_irq() was too early, moving the call to jme_start_irq() after
the call to jme_reset_link() makes it work.

Prior this change suspend/resume would fail unless /sys/power/pm_async=0
was explicitly specified.

Relevant bug report: https://bugzilla.kernel.org/show_bug.cgi?id=112351Signed-off-by: Diego Viola <diego.viola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Merge tag 'mac80211-for-davem-2016-02-23' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
Another small set of fixes:
 * stop critical protocol session on disconnect to avoid
   it getting stuck
 * wext: fix two RTNL message ordering issues
 * fix an uninitialized value (found by KASAN)
 * fix an out-of-bounds access (also found by KASAN)
 * clear connection keys when freeing them in all cases
   (IBSS, all other places already did so)
 * fix expected throughput unit to get consistent values
 * set default TX aggregation timeout to 0 in minstrel
   to avoid (really just hide) issues and perform better
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The fix in 35e2d115 ("tunnels: Allow IPv6 UDP checksums to be correctly
controlled.") changed behavior for bpf_set_tunnel_key() when in use with
IPv6 and thus uncovered a bug that TUNNEL_CSUM needed to be set but wasn't.
As a result, the stack dropped ingress vxlan IPv6 packets, that have been
sent via eBPF through collect meta data mode due to checksum now being zero.

Since after LCO, we enable IPv4 checksum by default, so make that analogous
and only provide a flag BPF_F_ZERO_CSUM_TX for the user to turn it off in
IPv4 case.

Fixes: 35e2d115 ("tunnels: Allow IPv6 UDP checksums to be correctly controlled.")
Fixes: c6c33454 ("bpf: support ipv6 for bpf_skb_{set,get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Otherwise we break the contract with GSO to only pass CHECKSUM_PARTIAL
skbs down. This can easily happen with UDP+IPv4 sockets with the first
MSG_MORE write smaller than the MTU, second write is a sendfile.

Returning -EOPNOTSUPP lets the callers fall back into normal sendmsg path,
were we calculate the checksum manually during copying.

Commit d749c9cb ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked
sockets") started to exposes this bug.

Fixes: d749c9cb ("ipv4: no CHECKSUM_PARTIAL on MSG_MORE corked sockets")
Reported-by: Jiri Benc <jbenc@redhat.com>
Cc: Jiri Benc <jbenc@redhat.com>
Reported-by: Wakko Warner <wakko@animx.eu.org>
Cc: Wakko Warner <wakko@animx.eu.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Under some circumstances, e.g. when connecting to a switch, the ethernet
port will not be connected to a PHY. In that case a "fixed-link" DT node
can be used to replace it.

https://stackoverflow.com/questions/31046172/device-tree-for-phy-less-connection-to-a-dsa-switch

This patch adds support for the "fixed-link" node to the nb8800 driver.
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Acked-by: Mans Rullgard <mans@mansr.com>
Cc: Mason <slash.tmp@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

The arithmetic to zero pad the last 64-bit word in the push buffer is not
correct.

1. It should be pdata + length to get to the end.
2. 'pdata' is void pointer and passing it to PTR_ALIGN() will cast the
aligned pointer to void.  Pass 'end' which is u64 pointer to PTR_ALIGN()
instead so that the aligned pointer - 1 is the last 64-bit pointer to data.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.

This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.

The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.

The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently it's converted into msecs, thus HZ=1000 intact.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Fixes: 740b0f18 ("tcp: switch rtt estimations to usec resolution")
Signed-off-by: David S. Miller <davem@davemloft.net>

New revison of Dell Wireless 5809e Gobi 4G HSPA+ Mobile Broadband Card has new idProduct

Bus 002 Device 006: ID 413c:81b3 Dell Computer Corp.
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0
  bDeviceSubClass         0
  bDeviceProtocol         0
  bMaxPacketSize0        64
  idVendor           0x413c Dell Computer Corp.
  idProduct          0x81b3
  bcdDevice            0.06
  iManufacturer           1 Sierra Wireless, Incorporated
  iProduct                2 Dell Wireless 5809e Gobi™ 4G HSPA+ Mobile Broadband Card
  iSerial                 3
  bNumConfigurations      2
Signed-off-by: Patrik Halfar <patrik_halfar@halfarit.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

When user-space has started a critical protocol session and a disconnect
event occurs, the rdev::crit_prot_nlportid remains set. This caused a
subsequent NL80211_CMD_CRIT_PROTO_START to fail (-EBUSY). Fix this by
clearing the rdev attribute and call .crit_proto_stop() callback upon
disconnect event.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The connection keys are zeroed out in all other cases except this
one. Let's fix the last one as well.
Signed-off-by: Ola Olsson <ola.olsson@sonymobile.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The value 5000 was put here with the addition of the timeout field to
ieee80211_start_tx_ba_session. It was originally added in mac80211 to
save resources for drivers like iwlwifi, which only supports a limited
number of concurrent aggregation sessions.

Since iwlwifi does not use minstrel_ht and other drivers don't need
this, 0 is a better default - especially since there have been
recent reports of aggregation setup related issues reproduced with
ath9k. This should improve stability without causing any adverse
effects.

Cc: stable@vger.kernel.org
Acked-by: Avery Pennarun <apenwarr@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Pull networking fixes from David Miller:
 "Looks like a lot, but mostly driver fixes scattered all over as usual.

  Of note:

   1) Add conditional sched in nf conntrack in cleanup to avoid NMI
      watchdogs.  From Florian Westphal.

   2) Fix deadlock in nfnetlink cttimeout, also from Floarian.

   3) Fix handling of slaves in bonding ARP monitor validation, from Jay
      Vosburgh.

   4) Callers of ip_cmsg_send() are responsible for freeing IP options,
      some were not doing so.  Fix from Eric Dumazet.

   5) Fix per-cpu bugs in mvneta driver, from Gregory CLEMENT.

   6) Fix vlan handling in mv88e6xxx DSA driver, from Vivien Didelot.

   7) bcm7xxx PHY driver bug fixes from Florian Fainelli.

   8) Avoid unaligned accesses to protocol headers wrt.  GRE, from
      Alexander Duyck.

   9) SKB leaks and other problems in arc_emac driver, from Alexander
      Kochetkov.

  10) tcp_v4_inbound_md5_hash() releases listener socket instead of
      request socket on error path, oops.  Fix from Eric Dumazet.

  11) Missing socket release in pppoe_rcv_core() that seems to have
      existed basically forever.  From Guillaume Nault.

  12) Missing slave_dev unregister in dsa_slave_create() error path,
      from Florian Fainelli.

  13) crypto_alloc_hash() never returns NULL, fix return value check in
      __tcp_alloc_md5sig_pool.  From Insu Yun.

  14) Properly expire exception route entries in ipv4, from Xin Long.

  15) Fix races in tcp/dccp listener socket dismantle, from Eric
      Dumazet.

  16) Don't set IFF_TX_SKB_SHARING in vxlan, geneve, or GRE, it's not
      legal.  These drivers modify the SKB on transmit.  From Jiri Benc.

  17) Fix regression in the initialziation of netdev->tx_queue_len.
      From Phil Sutter.

  18) Missing unlock in tipc_nl_add_bc_link() error path, from Insu Yun.

  19) SCTP port hash sizing does not properly ensure that table is a
      power of two in size.  From Neil Horman.

  20) Fix initializing of software copy of MAC address in fmvj18x_cs
      driver, from Ken Kawasaki"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (129 commits)
  bnx2x: Fix 84833 phy command handler
  bnx2x: Fix led setting for 84858 phy.
  bnx2x: Correct 84858 PHY fw version
  bnx2x: Fix 84833 RX CRC
  bnx2x: Fix link-forcing for KR2
  net: ethernet: davicom: fix devicetree irq resource
  fmvj18x_cs: fix incorrect indexing of dev->dev_addr[] when copying the MAC address
  Driver: Vmxnet3: Update Rx ring 2 max size
  net: netcp: rework the code for get/set sw_data in dma desc
  soc: ti: knav_dma: rename pad in struct knav_dma_desc to sw_data
  net: ti: netcp: restore get/set_pad_info() functionality
  MAINTAINERS: Drop myself as xen netback maintainer
  sctp: Fix port hash table size computation
  can: ems_usb: Fix possible tx overflow
  Bluetooth: hci_core: Avoid mixing up req_complete and req_complete_skb
  net: bcmgenet: Fix internal PHY link state
  af_unix: Don't use continue to re-execute unix_stream_read_generic loop
  unix_diag: fix incorrect sign extension in unix_lookup_by_ino
  bnxt_en: Failure to update PHY is not fatal condition.
  bnxt_en: Remove unnecessary call to update PHY settings.
  ...

Merge tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fixes from Guenter Roeck:
 "Two fixes headed for stable:

   - Remove an unnecessary speed_index lookup for thermal hook in the
     gpio-fan driver.  The unnecessary speed lookup can hog the system.

   - Handle negative conversion values correctly in the ads1015 driver"

* tag 'hwmon-for-linus-v4.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (gpio-fan) Remove un-necessary speed_index lookup for thermal hook
  hwmon: (ads1015) Handle negative conversion values correctly

Pull rdma fixes from Doug Ledford:
 "One ocrdma fix:

   - The new CQ API support was added to ocrdma, but they got the arming
     logic wrong, so without this, transfers eventually fail when they
     fail to arm the interrupt properly under load

  Two related fixes for mlx4:

   - When we added the 64bit extended counters support to the core IB
     code, they forgot to update the RoCE side of the mlx4 driver (the
     IB side they properly updated).

     I debated whether or not to include these patches as they could be
     considered feature enablement patches, but the existing code will
     blindy copy the 32bit counters, whether any counters were requested
     at all (a bug).

     These two patches make it (a) check to see that counters were
     requested and (b) copy the right counters (the 64bit support is
     new, the 32bit is not).  For that reason I went ahead and took
     them"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
  IB/mlx4: Add support for the port info class for RoCE ports
  IB/mlx4: Add support for extended counters over RoCE ports
  RDMA/ocrdma: Fix arm logic to align with new cq API

Pull i2c fixes from Wolfram Sang:
 "Some bugfixes from I2C for you:

  A fix for a RuntimePM regression with OMAP, a fix to enable TCO for
  Lewisburg platforms, and a typo fix while we are here"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: i801: Adding Intel Lewisburg support for iTCO
  i2c: uniphier: fix typos in error messages
  i2c: omap: Fix PM regression with deferred probe for pm_runtime_reinit

Merge tag 'linux-can-fixes-for-4.5-20160221' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2016-02-21

this is a pull reqeust of one patch for net/master.

The patch is by Gerhard Uttenthaler and fixes a potential tx overflow in the
ems_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: Fix 848xx phys

This series contains link-related fixes, mostly for the 848xx phys
[2 patches are for 84833, and 2 patches are for 84858].
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Current initialization sequence is lacking, causing some configurations
to fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The phy's firmware version isn't being parsed properly as it's
currently parsed like the rest of the 848xx phys.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's a problem in current 84833 phy configuration -
in case 1Gb link is configured and jumbo-sized packets are being
used, device will experience RX crc errors.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, when link is using KR2 it cannot be forced to any speed other
than 20g.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.om>
Signed-off-by: David S. Miller <davem@davemloft.net>

Johan Hedberg says:

====================
pull request: bluetooth 2016-02-20

Here's an important patch for 4.5 which fixes potential invalid pointer
access when processing completed Bluetooth HCI commands.

Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The dm9000 driver doesn't work in at least one device-tree
configuration, spitting an error message on irq resource :
[    1.062495] dm9000 8000000.ethernet: insufficient resources
[    1.068439] dm9000 8000000.ethernet: not found (-2).
[    1.073451] dm9000: probe of 8000000.ethernet failed with error -2

The reason behind is that the interrupt might be provided by a gpio
controller, not probed when dm9000 is probed, and needing the probe
deferral mechanism to apply.

Currently, the interrupt is directly taken from resources. This patch
changes this to use the more generic platform_get_irq(), which handles
the deferral.

Moreover, since commit Fixes: 7085a740 ("drivers: platform: parse
IRQ flags from resources"), the interrupt trigger flags are honored in
platform_get_irq(), so remove the needless code in dm9000.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Tested-by: Sergei Ianovich <ynvich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

fix incorrect indexing of dev->dev_addr[] when copying the MAC address
of FMV-J182 at buf[5].
Signed-off-by: Ken Kawasaki <ken_kawasaki@nifty.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Device emulation supports max size of 4096.
Signed-off-by: Shrikrishna Khare <skhare@vmware.com>
Signed-off-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Murali Karicheri says:

====================
net: ti: netcp: restore get/set_pad_info() functionality

This series fixes a regression and add some improvements for the ease
of maintainance. Incorporated comments against v1.

Changelogs:

 v2 : combined 2-3 into one patch as this involves a header change
      fixed a parse warning in 3/4 per comment from Arnd.
      Removed Sign-off from Arnd against 1/4
      added comments in 3/3 to alert on the usage of sw data per review
      comments
 v1 : added 2-4 to accomodate feedback received from review
 v0 : initial version to fix the regression (From Grygorii)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.

Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.

Rename the helpers to match with the updated dma desc field sw_data.

Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 89907779 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.

The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.

Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].

Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.

[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Arnd Bergmann <arnd@arndb.de>
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

Wei has been picking this up for quite a while now.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Wei Liu <wei.liu2@citrix.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Dmitry Vyukov noted recently that the sctp_port_hashtable had an error in
its size computation, observing that the current method never guaranteed
that the hashsize (measured in number of entries) would be a power of two,
which the input hash function for that table requires.  The root cause of
the problem is that two values need to be computed (one, the allocation
order of the storage requries, as passed to __get_free_pages, and two the
number of entries for the hash table).  Both need to be ^2, but for
different reasons, and the existing code is simply computing one order
value, and using it as the basis for both, which is wrong (i.e. it assumes
that ((1<<order)*PAGE_SIZE)/sizeof(bucket) is still ^2 when its not).

To fix this, we change the logic slightly.  We start by computing a goal
allocation order (which is limited by the maximum size hash table we want
to support.  Then we attempt to allocate that size table, decreasing the
order until a successful allocation is made.  Then, with the resultant
successful order we compute the number of buckets that hash table supports,
which we then round down to the nearest power of two, giving us the number
of entries the table actually supports.

I've tested this locally here, using non-debug and spinlock-debug kernels,
and the number of entries in the hashtable consistently work out to be
powers of two in all cases.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Dmitry Vyukov <dvyukov@google.com>
CC: Vladislav Yasevich <vyasevich@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch fixes the problem that more CAN messages could be sent to the
interface as could be send on the CAN bus. This was more likely for slow baud
rates. The sleeping _start_xmit was woken up in the _write_bulk_callback. Under
heavy TX load this produced another bulk transfer without checking the
free_slots variable and hence caused the overflow in the interface.
Signed-off-by: Gerhard Uttenthaler <uttenthaler@ems-wuensche.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Pull x86 fixes from Ingo Molnar:
 "This is unusually large, partly due to the EFI fixes that prevent
  accidental deletion of EFI variables through efivarfs that may brick
  machines.  These fixes are somewhat involved to maintain compatibility
  with existing install methods and other usage modes, while trying to
  turn off the 'rm -rf' bricking vector.

  Other fixes are for large page ioremap()s and for non-temporal
  user-memcpy()s"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/mm: Fix vmalloc_fault() to handle large pages properly
  hpet: Drop stale URLs
  x86/uaccess/64: Handle the caching of 4-byte nocache copies properly in __copy_user_nocache()
  x86/uaccess/64: Make the __copy_user_nocache() assembly code more readable
  lib/ucs2_string: Correct ucs2 -> utf8 conversion
  efi: Add pstore variables to the deletion whitelist
  efi: Make efivarfs entries immutable by default
  efi: Make our variable validation list include the guid
  efi: Do variable name validation tests in utf8
  efi: Use ucs2_as_utf8 in efivarfs instead of open coding a bad version
  lib/ucs2_string: Add ucs2 -> utf8 helper functions

Pull perf fixes from Ingo Molnar:
 "A handful of CPU hotplug related fixes"

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/core: Plug potential memory leak in CPU_UP_PREPARE
  perf/core: Remove the bogus and dangerous CPU_DOWN_FAILED hotplug state
  perf/core: Remove bogus UP_CANCELED hotplug state
  perf/x86/amd/uncore: Plug reference leak

Pull powerpc fixes from Michael Ellerman:
 - Fix build error on 32-bit with checkpoint restart from Aneesh Kumar
 - Fix dedotify for binutils >= 2.26 from Andreas Schwab
 - Don't trace hcalls on offline CPUs from Denis Kirjanov
 - eeh: Fix stale cached primary bus from Gavin Shan
 - eeh: Fix stale PE primary bus from Gavin Shan
 - mm: Fix Multi hit ERAT cause by recent THP update from Aneesh Kumar K.V
 - ioda: Set "read" permission when "write" is set from Alexey Kardashevskiy

* tag 'powerpc-4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/ioda: Set "read" permission when "write" is set
  powerpc/mm: Fix Multi hit ERAT cause by recent THP update
  powerpc/powernv: Fix stale PE primary bus
  powerpc/eeh: Fix stale cached primary bus
  powerpc/pseries: Don't trace hcalls on offline CPUs
  powerpc: Fix dedotify for binutils >= 2.26
  powerpc/book3s_32: Fix build error with checkpoint restart