In some weird cases it might be possible that the TPM does not set
STS.VALID within the given timeout time (or ever) but sets STS.EXPECT
(STS=0x0C) In this case the driver gets stuck in the while loop of
tpm_tis_send_data and loops endlessly.

Checking the return value of wait_for_tpm_stat fixes this and the driver
bails out correctly.  While at it fixing all other users since if the
TPM does not manage to set STS.VALID within the reasonable timeframe
something is definitely wrong and the driver should react correctly.
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Utilize runtime_pm for driving tpm crb idle states.
The framework calls cmd_ready from the pm_runtime_resume handler
and go idle from the pm_runtime_suspend handler.
The TPM framework should wake the device before transmit and receive.
In case the runtime_pm framework is not compiled in or enabled, the device
will be in the permanent ready state.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

This is preparation step for implementing tpm crb
runtime pm. We need to have tpm chip allocated
and populated before we access the runtime handlers.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

There is a HW bug in Skylake, and Broxton PCH Intel PTT device, where
most of the registers in the control area except START, REQUEST, CANCEL,
and LOC_CTRL lost retention when the device is in the idle state. Hence
we need to bring the device to ready state before accessing the other
registers. The fix brings device to ready state before trying to read
command and response buffer addresses in order to remap the for access.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinn@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

The register TPM_CRB_CTRL_REQ_x contains bits goIdle and cmdReady for
SW to indicate that the device can enter or should exit the idle state.

The legacy ACPI-start (SMI + DMA) based devices do not support these
bits and the idle state management is not exposed to the host SW.
Thus, this functionality only is enabled only for a CRB start (MMIO)
based devices.

Based on Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
original patch:
'tpm_crb: implement power tpm crb power management'

To keep the implementation local to the hw we don't use wait_for_tpm_stat
for polling the TPM_CRB_CTRL_REQ.

[jarkko.sakkinen@linux.intel.com: removed cmdReady debug trace on a
 success case due the heavy amount of log traffic it causes.]
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>

Merge branch 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/zohar/linux-integrity into next

Convert isec->lock from a mutex into a spinlock.  Instead of holding
the lock while sleeping in inode_doinit_with_dentry, set
isec->initialized to LABEL_PENDING and release the lock.  Then, when
the sid has been determined, re-acquire the lock.  If isec->initialized
is still set to LABEL_PENDING, set isec->sid; otherwise, the sid has
been set by another task (LABEL_INITIALIZED) or invalidated
(LABEL_INVALID) in the meantime.

This fixes a deadlock on gfs2 where

 * one task is in inode_doinit_with_dentry -> gfs2_getxattr, holds
   isec->lock, and tries to acquire the inode's glock, and

 * another task is in do_xmote -> inode_go_inval ->
   selinux_inode_invalidate_secctx, holds the inode's glock, and
   tries to acquire isec->lock.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
[PM: minor tweaks to keep checkpatch.pl happy]
Signed-off-by: Paul Moore <paul@paul-moore.com>

When a new capability is defined, SELinux needs to be updated.
Trigger a build error if a new capability is defined without
corresponding update to security/selinux/include/classmap.h's
COMMON_CAP2_PERMS.  This is similar to BUILD_BUG_ON() guards
in the SELinux nlmsgtab code to ensure that SELinux tracks
new netlink message types as needed.

Note that there is already a similar build guard in
security/selinux/hooks.c to detect when more than 64
capabilities are defined, since that will require adding
a third capability class to SELinux.

A nicer way to do this would be to extend scripts/selinux/genheaders
or a similar tool to auto-generate the necessary definitions and code
for SELinux capability checking from include/uapi/linux/capability.h.
AppArmor does something similar in its Makefile, although it only
needs to generate a single table of names.  That is left as future
work.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
[PM: reformat the description to keep checkpatch.pl happy]
Signed-off-by: Paul Moore <paul@paul-moore.com>

At present, one can write any signed integer value to
/sys/fs/selinux/enforce and it will be stored,
e.g. echo -1 > /sys/fs/selinux/enforce or echo 2 >
/sys/fs/selinux/enforce. This makes no real difference
to the kernel, since it only ever cares if it is zero or non-zero,
but some userspace code compares it with 1 to decide if SELinux
is enforcing, and this could confuse it. Only a process that is
already root and is allowed the setenforce permission in SELinux
policy can write to /sys/fs/selinux/enforce, so this is not considered
to be a security issue, but it should be fixed.
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Paul Moore <paul@paul-moore.com>

The invalid Smack label ("") and the Huh ("?") Smack label
serve the same purpose and having both is unnecessary.
While pulling out the invalid label it became clear that
the use of smack_from_secid() was inconsistent, so that
is repaired. The setting of inode labels to the invalid
label could never happen in a functional system, has
never been observed in the wild and is not what you'd
really want for a failure behavior in any case. That is
removed.
Signed-off-by: Casey Schaufler <casey@schaufler-ca.com>

Since smack_parse_opts_str() is calling match_strdup() which uses
GFP_KERNEL, it is safe to use GFP_KERNEL from kcalloc() which is
called by smack_parse_opts_str().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>

Now that isec->initialized == LABEL_INITIALIZED implies that
isec->sclass is valid, skip such inodes immediately in
inode_doinit_with_dentry.

For the remaining inodes, initialize isec->sclass at the beginning of
inode_doinit_with_dentry to simplify the code.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>

Pass the file mode of the proc inode to be created to
proc_pid_make_inode.  In proc_pid_make_inode, initialize inode->i_mode
before calling security_task_to_inode.  This allows selinux to set
isec->sclass right away without introducing "half-initialized" inode
security structs.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>

Fix the comment for function __inode_security_revalidate, which returns
an integer.

Use the LABEL_* constants consistently for isec->initialized.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>

Since selinux_parse_opts_str() is calling match_strdup() which uses
GFP_KERNEL, it is safe to use GFP_KERNEL from kcalloc() which is
called by selinux_parse_opts_str().
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Paul Moore <paul@paul-moore.com>

In general the handling of IMA/EVM xattrs is good, but I found
a few locations where either the xattr size or the value of the
type field in the xattr are not checked. Add a few simple checks
to these locations to prevent malformed or malicious xattrs from
causing problems.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>

This patch includes the reason for going into TPM-bypass mode
and not using the TPM.

Signed-off-by: Mimi Zohar (zohar@linux.vnet.ibm>

Userspace applications have been modified to write security xattrs,
but they are not context aware.  In the case of security.ima, the
security xattr can be either a file hash or a file signature.
Permitting writing one, but not the other requires the application to
be context aware.

In addition, userspace applications might write files to a staging
area, which might not be in policy, and then change some file metadata
(eg. owner) making it in policy.  As a result, these files are not
labeled properly.

This reverts commit c68ed80c, which
prevents writing file hashes as security.ima xattrs.
Requested-by: Patrick Ohly <patrick.ohly@intel.com>
Cc: Dmitry Kasatkin <dmitry.kasatkin@gmail.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>

When the "policy" securityfs file is opened for read, it is opened as a
sequential file. However, when it is eventually released, there is no
cleanup for the sequential file, therefore some memory is leaked.

This patch adds a call to seq_release() in ima_release_policy() to clean up
the memory when the file is opened for read.

Fixes: 80eae209 IMA: allow reading back the current policy
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Eric Richter <erichte@linux.vnet.ibm.com>
Tested-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>

Pull KVM fixes from Paolo Bonzini:
 "ARM fixes.  There are a couple pending x86 patches but they'll have to
  wait for next week"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: arm/arm64: vgic: Kick VCPUs when queueing already pending IRQs
  KVM: arm/arm64: vgic: Prevent access to invalid SPIs
  arm/arm64: KVM: Perform local TLB invalidation when multiplexing vcpus on a single CPU

Merge media fixes from Mauro Carvalho Chehab:
 "This contains two patches fixing problems with my patch series meant
  to make USB drivers to work again after the DMA on stack changes.

  The last patch on this series is actually not related to DMA on stack.
  It solves a longstanding bug affecting module unload, causing
  module_put() to be called twice. It was reported by the user who
  reported and tested the issues with the gp8psk driver with the DMA
  fixup patches. As we're late at -rc cycle, maybe you prefer to not
  apply it right now. If this is the case, I'll add to the pile of
  patches for 4.10.

  Exceptionally this time, I'm sending the patches via e-mail, because
  I'm on another trip, and won't be able to use the usual procedure
  until Monday. Also, it is only three patches, and you followed already
  the discussions about the first one"

* emailed patches from Mauro Carvalho Chehab <mchehab@osg.samsung.com>:
  gp8psk: Fix DVB frontend attach
  gp8psk: fix gp8psk_usb_in_op() logic
  dvb-usb: move data_mutex to struct dvb_usb_device

Pull char/misc fixes from Greg KH:
 "Here are three small driver fixes for some reported issues for
  4.9-rc5.

  One for the hyper-v subsystem, fixing up a naming issue that showed up
  in 4.9-rc1, one mei driver fix, and one fix for parallel ports,
  resolving a reported regression.

  All have been in linux-next with no reported issues"

* tag 'char-misc-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  ppdev: fix double-free of pp->pdev->name
  vmbus: make sysfs names consistent with PCI
  mei: bus: fix received data size check in NFC fixup

Pull driver core fixes from Greg KH:
 "Here are two driver core fixes for 4.9-rc5.

  The first resolves an issue with some drivers not liking to be unbound
  and bound again (if CONFIG_DEBUG_TEST_DRIVER_REMOVE is enabled), which
  solves some reported problems with graphics and storage drivers. The
  other resolves a smatch error with the 4.9-rc1 driver core changes
  around this feature.

  Both have been in linux-next with no reported issues"

* tag 'driver-core-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  driver core: fix smatch warning on dev->bus check
  driver core: skip removal test for non-removable drivers

Pull staging/IIO fixes from Grek KH:
 "Here are a few small staging and iio driver fixes for reported issues.

  The last one was cherry-picked from my -next branch to resolve a build
  warning that Arnd fixed, in his quest to be able to turn
  -Wmaybe-uninitialized back on again. That patch, and all of the
  others, have been in linux-next for a while with no reported issues"

* tag 'staging-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  iio: maxim_thermocouple: detect invalid storage size in read()
  staging: nvec: remove managed resource from PS2 driver
  Revert "staging: nvec: ps2: change serio type to passthrough"
  drivers: staging: nvec: remove bogus reset command for PS/2 interface
  staging: greybus: arche-platform: fix device reference leak
  staging: comedi: ni_tio: fix buggy ni_tio_clock_period_ps() return value
  staging: sm750fb: Fix bugs introduced by early commits
  iio: hid-sensors: Increase the precision of scale to fix wrong reading interpretation.
  iio: orientation: hid-sensor-rotation: Add PM function (fix non working driver)
  iio: st_sensors: fix scale configuration for h3lis331dl
  staging: iio: ad5933: avoid uninitialized variable in error case

Pull USB / PHY fixes from Greg KH:
 "Here are a number of small USB and PHY driver fixes for 4.9-rc5

  Nothing major, just small fixes for reported issues, all of these have
  been in linux-next for a while with no reported issues"

* tag 'usb-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  USB: cdc-acm: fix TIOCMIWAIT
  cdc-acm: fix uninitialized variable
  drivers/usb: Skip auto handoff for TI and RENESAS usb controllers
  usb: musb: remove duplicated actions
  usb: musb: da8xx: Don't print phy error on -EPROBE_DEFER
  phy: sun4i: check PMU presence when poking unknown bit of pmu
  phy-rockchip-pcie: remove deassert of phy_rst from exit callback
  phy: da8xx-usb: rename the ohci device to ohci-da8xx
  phy: Add reset callback for not generic phy
  uwb: fix device reference leaks
  usb: gadget: u_ether: remove interrupt throttling
  usb: dwc3: st: add missing <linux/pinctrl/consumer.h> include
  usb: dwc3: Fix error handling for core init

Pull more block fixes from Jens Axboe:
 "Since I mistakenly left out the lightnvm regression fix yesterday and
  the aoeblk seems adequately tested at this point, might as well send
  out another pull to make -rc5"

* 'for-linus' of git://git.kernel.dk/linux-block:
  aoe: fix crash in page count manipulation
  lightnvm: invalid offset calculation for lba_shift

Pull SCSI fixes from James Bottomley:
 "The megaraid_sas patch in here fixes a major regression in the last
  fix set that made all megaraid_sas cards unusable. It turns out no-one
  had actually tested such an "obvious" fix, sigh. The fix for the fix
  has been tested ...

  The next most serious is the vmw_pvscsi abort problem which basically
  means that aborts don't work on the vmware paravirt devices and error
  handling always escalates to reset.

  The rest are an assortment of missed reference counting in certain
  paths and corner case bugs that show up on some architectures"

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: megaraid_sas: fix macro MEGASAS_IS_LOGICAL to avoid regression
  scsi: qla2xxx: fix invalid DMA access after command aborts in PCI device remove
  scsi: qla2xxx: do not queue commands when unloading
  scsi: libcxgbi: fix incorrect DDP resource cleanup
  scsi: qla2xxx: Fix scsi scan hang triggered if adapter fails during init
  scsi: scsi_dh_alua: Fix a reference counting bug
  scsi: vmw_pvscsi: return SUCCESS for successful command aborts
  scsi: mpt3sas: Fix for block device of raid exists even after deleting raid disk
  scsi: scsi_dh_alua: fix missing kref_put() in alua_rtpg_work()

Pull clk fixes from Stephen Boyd:
 "The typical collection of minor bug fixes in clk drivers. We don't
  have anything in the core framework here, just driver fixes.

  There's a boot fix for Samsung devices and a safety measure for qoriq
  to prevent CPUs from running too fast. There's also a fix for i.MX6Q
  to properly handle audio clock rates. We also have some "that's
  obviously wrong" fixes like bad NULL pointer checks in the MPP driver
  and a poor usage of __pa in the xgene clk driver that are fixed here"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: mmp: pxa910: fix return value check in pxa910_clk_init()
  clk: mmp: pxa168: fix return value check in pxa168_clk_init()
  clk: mmp: mmp2: fix return value check in mmp2_clk_init()
  clk: qoriq: Don't allow CPU clocks higher than starting value
  clk: imx: fix integer overflow in AV PLL round rate
  clk: xgene: Don't call __pa on ioremaped address
  clk/samsung: Use CLK_OF_DECLARE_DRIVER initialization method for CLKOUT
  clk: rockchip: don't return NULL when failing to register ddrclk branch

The DVB binding schema at the DVB core assumes that the frontend is a
separate driver.  Faling to do that causes OOPS when the module is
removed, as it tries to do a symbol_put_addr on an internal symbol,
causing craches like:

    WARNING: CPU: 1 PID: 28102 at kernel/module.c:1108 module_put+0x57/0x70
    Modules linked in: dvb_usb_gp8psk(-) dvb_usb dvb_core nvidia_drm(PO) nvidia_modeset(PO) snd_hda_codec_hdmi snd_hda_intel snd_hda_codec snd_hwdep snd_hda_core snd_pcm snd_timer snd soundcore nvidia(PO) [last unloaded: rc_core]
    CPU: 1 PID: 28102 Comm: rmmod Tainted: P        WC O 4.8.4-build.1 #1
    Hardware name: MSI MS-7309/MS-7309, BIOS V1.12 02/23/2009
    Call Trace:
       dump_stack+0x44/0x64
       __warn+0xfa/0x120
       module_put+0x57/0x70
       module_put+0x57/0x70
       warn_slowpath_null+0x23/0x30
       module_put+0x57/0x70
       gp8psk_fe_set_frontend+0x460/0x460 [dvb_usb_gp8psk]
       symbol_put_addr+0x27/0x50
       dvb_usb_adapter_frontend_exit+0x3a/0x70 [dvb_usb]

From Derek's tests:
    "Attach bug is fixed, tuning works, module unloads without
     crashing. Everything seems ok!"
Reported-by: Derek <user.vdr@gmail.com>
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bc29131ecb10 ("[media] gp8psk: don't do DMA on stack") fixed the
usage of DMA on stack, but the memcpy was wrong for gp8psk_usb_in_op().
Fix it.

From Derek's email:
    "Fix confirmed using 2 different Skywalker models with
     HD mpeg4, SD mpeg2."
Suggested-by: Johannes Stezenbach <js@linuxtv.org>
Fixes: bc29131ecb10 ("[media] gp8psk: don't do DMA on stack")
Tested-by: Derek <user.vdr@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The data_mutex is initialized too late, as it is needed for
each device driver's power control, causing an OOPS:

    dvb-usb: found a 'TerraTec/qanu USB2.0 Highspeed DVB-T Receiver' in warm state.
    BUG: unable to handle kernel NULL pointer dereference at           (null)
    IP: [<ffffffff846617af>] __mutex_lock_slowpath+0x6f/0x100 PGD 0
    Oops: 0002 [#1] SMP
    Modules linked in: dvb_usb_cinergyT2(+) dvb_usb
    CPU: 0 PID: 2029 Comm: modprobe Not tainted 4.9.0-rc4-dvbmod #24
    Hardware name: FUJITSU LIFEBOOK A544/FJNBB35 , BIOS Version 1.17 05/09/2014
    task: ffff88020e943840 task.stack: ffff8801f36ec000
    RIP: 0010:[<ffffffff846617af>]  [<ffffffff846617af>] __mutex_lock_slowpath+0x6f/0x100
    RSP: 0018:ffff8801f36efb10  EFLAGS: 00010282
    RAX: 0000000000000000 RBX: ffff88021509bdc8 RCX: 00000000c0000100
    RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff88021509bdcc
    RBP: ffff8801f36efb58 R08: ffff88021f216320 R09: 0000000000100000
    R10: ffff88021f216320 R11: 00000023fee6c5a1 R12: ffff88020e943840
    R13: ffff88021509bdcc R14: 00000000ffffffff R15: ffff88021509bdd0
    FS:  00007f21adb86740(0000) GS:ffff88021f200000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
    CR2: 0000000000000000 CR3: 0000000215bce000 CR4: 00000000001406f0
    Call Trace:
       mutex_lock+0x16/0x25
       cinergyt2_power_ctrl+0x1f/0x60 [dvb_usb_cinergyT2]
       dvb_usb_device_init+0x21e/0x5d0 [dvb_usb]
       cinergyt2_usb_probe+0x21/0x50 [dvb_usb_cinergyT2]
       usb_probe_interface+0xf3/0x2a0
       driver_probe_device+0x208/0x2b0
       __driver_attach+0x87/0x90
       driver_probe_device+0x2b0/0x2b0
       bus_for_each_dev+0x52/0x80
       bus_add_driver+0x1a3/0x220
       driver_register+0x56/0xd0
       usb_register_driver+0x77/0x130
       do_one_initcall+0x46/0x180
       free_vmap_area_noflush+0x38/0x70
       kmem_cache_alloc+0x84/0xc0
       do_init_module+0x50/0x1be
       load_module+0x1d8b/0x2100
       find_symbol_in_section+0xa0/0xa0
       SyS_finit_module+0x89/0x90
       entry_SYSCALL_64_fastpath+0x13/0x94
    Code: e8 a7 1d 00 00 8b 03 83 f8 01 0f 84 97 00 00 00 48 8b 43 10 4c 8d 7b 08 48 89 63 10 4c 89 3c 24 41 be ff ff ff ff 48 89 44 24 08 <48> 89 20 4c 89 64 24 10 eb 1a 49 c7 44 24 08 02 00 00 00 c6 43 RIP  [<ffffffff846617af>] __mutex_lock_slowpath+0x6f/0x100 RSP <ffff8801f36efb10>
    CR2: 0000000000000000

So, move it to the struct dvb_usb_device and initialize it
before calling the driver's callbacks.
Reported-by: Jörg Otte <jrg.otte@gmail.com>
Tested-by: Jörg Otte <jrg.otte@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

As found by gcc -Wmaybe-uninitialized, having a storage_bytes value other
than 2 or 4 will result in undefined behavior:

drivers/iio/temperature/maxim_thermocouple.c: In function 'maxim_thermocouple_read':
drivers/iio/temperature/maxim_thermocouple.c:141:5: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]

This probably cannot happen, but returning -EINVAL here is appropriate
and makes gcc happy and the code more robust.

Fixes: 231147ee ("iio: maxim_thermocouple: Align 16 bit big endian value of raw reads")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
(cherry picked from commit 32cb7d27)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

aoeblk contains some mysterious code, that wants to elevate the bio
vec page counts while it's under IO. That is not needed, it's
fragile, and it's causing kernel oopses for some.
Reported-by: Tested-by: Don Koch <kochd@us.ibm.com>
Tested-by: Tested-by: Don Koch <kochd@us.ibm.com>
Signed-off-by: Jens Axboe <axboe@fb.com>

The ns->lba_shift assumes its value to be the logarithmic of the
LA size. A previous patch duplicated the lba_shift calculation into
lightnvm. It prematurely also subtracted a 512byte shift, which commonly
is applied per-command. The 512byte shift being subtracted twice led to
data loss when restoring the logical to physical mapping table from
device and when issuing I/O commands using rrpc.

Fix offset by removing the 512byte shift subtraction when calculating
lba_shift.

Fixes: b0b4e09c "lightnvm: control life of nvm_dev in driver"
Reported-by: Javier González <javier@cnexlabs.com>
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>

Pull ACPI fix from Rafael Wysocki:
 "Fix a recent regression in the 8250_dw serial driver introduced by
  adding a quirk for the APM X-Gene SoC to it which uncovered an issue
  related to the handling of built-in device properties in the core ACPI
  device enumeration code (Heikki Krogerus)"

* tag 'acpi-4.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / platform: Add support for build-in properties