- 07 Oct, 2019 30 commits
-
-
Daniel Drake authored
[ Upstream commit d21b8adb ] When cold-booting Asus X434DA, GPIO 7 is found to be already configured as an interrupt, and the GPIO level is found to be in a state that causes the interrupt to fire. As soon as pinctrl-amd probes, this interrupt fires and invokes amd_gpio_irq_handler(). The IRQ is acked, but no GPIO-IRQ handler was invoked, so the GPIO level being unchanged just causes another interrupt to fire again immediately after. This results in an interrupt storm causing this platform to hang during boot, right after pinctrl-amd is probed. Detect this situation and disable the GPIO interrupt when this happens. This enables the affected platform to boot as normal. GPIO 7 actually is the I2C touchpad interrupt line, and later on, i2c-multitouch loads and re-enables this interrupt when it is ready to handle it. Instead of this approach, I considered disabling all GPIO interrupts at probe time, however that seems a little risky, and I also confirmed that Windows does not seem to have this behaviour: the same 41 GPIO IRQs are enabled under both Linux and Windows, which is a far larger collection than the GPIOs referenced by the DSDT on this platform. Signed-off-by:
Daniel Drake <drake@endlessm.com> Link: https://lore.kernel.org/r/20190814090540.7152-1-drake@endlessm.comSigned-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Mark Menzynski authored
[ Upstream commit a1af2afb ] Some, mostly Fermi, vbioses appear to have zero max voltage. That causes Nouveau to not parse voltage entries, thus users not being able to set higher clocks. When changing this value Nvidia driver still appeared to ignore it, and I wasn't able to find out why, thus the code is ignoring the value if it is zero. CC: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
Mark Menzynski <mmenzyns@redhat.com> Reviewed-by:
Karol Herbst <kherbst@redhat.com> Signed-off-by:
Ben Skeggs <bskeggs@redhat.com> Signed-off-by:
-
hexin authored
[ Upstream commit 92c80268 ] vfio_pci_enable() saves the device's initial configuration information with the intent that it is restored in vfio_pci_disable(). However, the commit referenced in Fixes: below replaced the call to __pci_reset_function_locked(), which is not wrapped in a state save and restore, with pci_try_reset_function(), which overwrites the restored device state with the current state before applying it to the device. Reinstate use of __pci_reset_function_locked() to return to the desired behavior. Fixes: 890ed578 ("vfio-pci: Use pci "try" reset interface") Signed-off-by:
hexin <hexin15@baidu.com> Signed-off-by:
Liu Qi <liuqi16@baidu.com> Signed-off-by:
Zhang Yu <zhangyu31@baidu.com> Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Sam Bobroff authored
[ Upstream commit aa06e3d6 ] The EEH_DEV_NO_HANDLER flag is used by the EEH system to prevent the use of driver callbacks in drivers that have been bound part way through the recovery process. This is necessary to prevent later stage handlers from being called when the earlier stage handlers haven't, which can be confusing for drivers. However, the flag is set for all devices that are added after boot time and only cleared at the end of the EEH recovery process. This results in hot plugged devices erroneously having the flag set during the first recovery after they are added (causing their driver's handlers to be incorrectly ignored). To remedy this, clear the flag at the beginning of recovery processing. The flag is still cleared at the end of recovery processing, although it is no longer really necessary. Also clear the flag during eeh_handle_special_event(), for the same reasons. Signed-off-by:
Sam Bobroff <sbobroff@linux.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/b8ca5629d27de74c957d4f4b250177d1b6fc4bbd.1565930772.git.sbobroff@linux.ibm.comSigned-off-by:
-
Sowjanya Komatineni authored
[ Upstream commit c2cf351e ] pmx_writel uses writel which inserts write barrier before the register write. This patch has fix to replace writel with writel_relaxed followed by a readback and memory barrier to ensure write operation is completed for successful pinctrl change. Acked-by:
Thierry Reding <treding@nvidia.com> Reviewed-by:
Dmitry Osipenko <digetx@gmail.com> Signed-off-by:
Sowjanya Komatineni <skomatineni@nvidia.com> Link: https://lore.kernel.org/r/1565984527-5272-2-git-send-email-skomatineni@nvidia.comSigned-off-by:
-
Nathan Lynch authored
[ Upstream commit ccfb5bd7 ] After a partition migration, pseries_devicetree_update() processes changes to the device tree communicated from the platform to Linux. This is a relatively heavyweight operation, with multiple device tree searches, memory allocations, and conversations with partition firmware. There's a few levels of nested loops which are bounded only by decisions made by the platform, outside of Linux's control, and indeed we have seen RCU stalls on large systems while executing this call graph. Use cond_resched() in these loops so that the cpu is yielded when needed. Signed-off-by:
Nathan Lynch <nathanl@linux.ibm.com> Signed-off-by:
-
Christophe Leroy authored
[ Upstream commit 38a0d0cd ] We see warnings such as: kernel/futex.c: In function 'do_futex': kernel/futex.c:1676:17: warning: 'oldval' may be used uninitialized in this function [-Wmaybe-uninitialized] return oldval == cmparg; ^ kernel/futex.c:1651:6: note: 'oldval' was declared here int oldval, ret; ^ This is because arch_futex_atomic_op_inuser() only sets *oval if ret is 0 and GCC doesn't see that it will only use it when ret is 0. Anyway, the non-zero ret path is an error path that won't suffer from setting *oval, and as *oval is a local var in futex_atomic_op_inuser() it will have no impact. Signed-off-by:
Christophe Leroy <christophe.leroy@c-s.fr> [mpe: reword change log slightly] Signed-off-by:
-
Nathan Lynch authored
[ Upstream commit a6717c01 ] The LPAR migration implementation and userspace-initiated cpu hotplug can interleave their executions like so: 1. Set cpu 7 offline via sysfs. 2. Begin a partition migration, whose implementation requires the OS to ensure all present cpus are online; cpu 7 is onlined: rtas_ibm_suspend_me -> rtas_online_cpus_mask -> cpu_up This sets cpu 7 online in all respects except for the cpu's corresponding struct device; dev->offline remains true. 3. Set cpu 7 online via sysfs. _cpu_up() determines that cpu 7 is already online and returns success. The driver core (device_online) sets dev->offline = false. 4. The migration completes and restores cpu 7 to offline state: rtas_ibm_suspend_me -> rtas_offline_cpus_mask -> cpu_down This leaves cpu7 in a state where the driver core considers the cpu device online, but in all other respects it is offline and unused. Attempts to online the cpu via sysfs appear to succeed but the driver core actually does not pass the request to the lower-level cpuhp support code. This makes the cpu unusable until the cpu device is manually set offline and then online again via sysfs. Instead of directly calling cpu_up/cpu_down, the migration code should use the higher-level device core APIs to maintain consistent state and serialize operations. Fixes: 120496ac ("powerpc: Bring all threads online prior to migration/hibernation") Signed-off-by:
Gautham R. Shenoy <ego@linux.vnet.ibm.com> Signed-off-by:
-
Cédric Le Goater authored
[ Upstream commit c3e0dbd7 ] Currently, the xmon 'dx' command calls OPAL to dump the XIVE state in the OPAL logs and also outputs some of the fields of the internal XIVE structures in Linux. The OPAL calls can only be done on baremetal (PowerNV) and they crash a pseries machine. Fix by checking the hypervisor feature of the CPU. Signed-off-by:
Cédric Le Goater <clg@kaod.org> Signed-off-by:
-
Stephen Boyd authored
[ Upstream commit 1a4549c1 ] A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions. Cc: Jun Nie <jun.nie@linaro.org> Cc: Shawn Guo <shawnguo@kernel.org> Signed-off-by:
Stephen Boyd <sboyd@kernel.org> Link: https://lkml.kernel.org/r/20190815160020.183334-3-sboyd@kernel.orgSigned-off-by:
-
Stephen Boyd authored
[ Upstream commit f6c90df8 ] A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions. Cc: Chunyan Zhang <zhang.chunyan@linaro.org> Cc: Baolin Wang <baolin.wang@linaro.org> Signed-off-by:
Baolin Wang <baolin.wang@linaro.org> Acked-by:
Chunyan Zhang <zhang.chunyan@linaro.org> Signed-off-by:
-
Stephen Boyd authored
[ Upstream commit af55dadf ] A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions. Cc: Guo Zeng <Guo.Zeng@csr.com> Cc: Barry Song <Baohua.Song@csr.com> Signed-off-by:
-
Stephen Boyd authored
[ Upstream commit cf9ec1fc ] A future patch is going to change semantics of clk_register() so that clk_hw::init is guaranteed to be NULL after a clk is registered. Avoid referencing this member here so that we don't run into NULL pointer exceptions. Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
Alexey Kardashevskiy authored
[ Upstream commit c37c792d ] We allocate only the first level of multilevel TCE tables for KVM already (alloc_userspace_copy==true), and the rest is allocated on demand. This is not enabled though for bare metal. This removes the KVM limitation (implicit, via the alloc_userspace_copy parameter) and always allocates just the first level. The on-demand allocation of missing levels is already implemented. As from now on DMA map might happen with disabled interrupts, this allocates TCEs with GFP_ATOMIC; otherwise lockdep reports errors 1]. In practice just a single page is allocated there so chances for failure are quite low. To save time when creating a new clean table, this skips non-allocated indirect TCE entries in pnv_tce_free just like we already do in the VFIO IOMMU TCE driver. This changes the default level number from 1 to 2 to reduce the amount of memory required for the default 32bit DMA window at the boot time. The default window size is up to 2GB which requires 4MB of TCEs which is unlikely to be used entirely or at all as most devices these days are 64bit capable so by switching to 2 levels by default we save 4032KB of RAM per a device. While at this, add __GFP_NOWARN to alloc_pages_node() as the userspace can trigger this path via VFIO, see the failure and try creating a table again with different parameters which might succeed. [1]: === BUG: sleeping function called from invalid context at mm/page_alloc.c:4596 in_atomic(): 1, irqs_disabled(): 1, pid: 1038, name: scsi_eh_1 2 locks held by scsi_eh_1/1038: #0: 000000005efd659a (&host->eh_mutex){+.+.}, at: ata_eh_acquire+0x34/0x80 #1: 0000000006cf56a6 (&(&host->lock)->rlock){....}, at: ata_exec_internal_sg+0xb0/0x5c0 irq event stamp: 500 hardirqs last enabled at (499): [<c000000000cb8a74>] _raw_spin_unlock_irqrestore+0x94/0xd0 hardirqs last disabled at (500): [<c000000000cb85c4>] _raw_spin_lock_irqsave+0x44/0x120 softirqs last enabled at (0): [<c000000000101120>] copy_process.isra.4.part.5+0x640/0x1a80 softirqs last disabled at (0): [<0000000000000000>] 0x0 CPU: 73 PID: 1038 Comm: scsi_eh_1 Not tainted 5.2.0-rc6-le_nv2_aikATfstn1-p1 #634 Call Trace: [c000003d064cef50] [c000000000c8e6c4] dump_stack+0xe8/0x164 (unreliable) [c000003d064cefa0] [c00000000014ed78] ___might_sleep+0x2f8/0x310 [c000003d064cf020] [c0000000003ca084] __alloc_pages_nodemask+0x2a4/0x1560 [c000003d064cf220] [c0000000000c2530] pnv_alloc_tce_level.isra.0+0x90/0x130 [c000003d064cf290] [c0000000000c2888] pnv_tce+0x128/0x3b0 [c000003d064cf360] [c0000000000c2c00] pnv_tce_build+0xb0/0xf0 [c000003d064cf3c0] [c0000000000bbd9c] pnv_ioda2_tce_build+0x3c/0xb0 [c000003d064cf400] [c00000000004cfe0] ppc_iommu_map_sg+0x210/0x550 [c000003d064cf510] [c00000000004b7a4] dma_iommu_map_sg+0x74/0xb0 [c000003d064cf530] [c000000000863944] ata_qc_issue+0x134/0x470 [c000003d064cf5b0] [c000000000863ec4] ata_exec_internal_sg+0x244/0x5c0 [c000003d064cf700] [c0000000008642d0] ata_exec_internal+0x90/0xe0 [c000003d064cf780] [c0000000008650ac] ata_dev_read_id+0x2ec/0x640 [c000003d064cf8d0] [c000000000878e28] ata_eh_recover+0x948/0x16d0 [c000003d064cfa10] [c00000000087d760] sata_pmp_error_handler+0x480/0xbf0 [c000003d064cfbc0] [c000000000884624] ahci_error_handler+0x74/0xe0 [c000003d064cfbf0] [c000000000879fa8] ata_scsi_port_error_handler+0x2d8/0x7c0 [c000003d064cfca0] [c00000000087a544] ata_scsi_error+0xb4/0x100 [c000003d064cfd00] [c000000000802450] scsi_error_handler+0x120/0x510 [c000003d064cfdb0] [c000000000140c48] kthread+0x1b8/0x1c0 [c000003d064cfe20] [c00000000000bd8c] ret_from_kernel_thread+0x5c/0x70 ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) irq event stamp: 2305 ======================================================== hardirqs last enabled at (2305): [<c00000000000e4c8>] fast_exc_return_irq+0x28/0x34 hardirqs last disabled at (2303): [<c000000000cb9fd0>] __do_softirq+0x4a0/0x654 WARNING: possible irq lock inversion dependency detected 5.2.0-rc6-le_nv2_aikATfstn1-p1 #634 Tainted: G W softirqs last enabled at (2304): [<c000000000cba054>] __do_softirq+0x524/0x654 softirqs last disabled at (2297): [<c00000000010f278>] irq_exit+0x128/0x180 -------------------------------------------------------- swapper/0/0 just changed the state of lock: 0000000006cf56a6 (&(&host->lock)->rlock){-...}, at: ahci_single_level_irq_intr+0xac/0x120 but this lock took another, HARDIRQ-unsafe lock in the past: (fs_reclaim){+.+.} and interrupts could create inverse lock ordering between them. other info that might help us debug this: Possible interrupt unsafe locking scenario: CPU0 CPU1 ---- ---- lock(fs_reclaim); local_irq_disable(); lock(&(&host->lock)->rlock); lock(fs_reclaim); <Interrupt> lock(&(&host->lock)->rlock); *** DEADLOCK *** no locks held by swapper/0/0. the shortest dependencies between 2nd lock and 1st lock: -> (fs_reclaim){+.+.} ops: 167579 { HARDIRQ-ON-W at: lock_acquire+0xf8/0x2a0 fs_reclaim_acquire.part.23+0x44/0x60 kmem_cache_alloc_node_trace+0x80/0x590 alloc_desc+0x64/0x270 __irq_alloc_descs+0x2e4/0x3a0 irq_domain_alloc_descs+0xb0/0x150 irq_create_mapping+0x168/0x2c0 xics_smp_probe+0x2c/0x98 pnv_smp_probe+0x40/0x9c smp_prepare_cpus+0x524/0x6c4 kernel_init_freeable+0x1b4/0x650 kernel_init+0x2c/0x148 ret_from_kernel_thread+0x5c/0x70 SOFTIRQ-ON-W at: lock_acquire+0xf8/0x2a0 fs_reclaim_acquire.part.23+0x44/0x60 kmem_cache_alloc_node_trace+0x80/0x590 alloc_desc+0x64/0x270 __irq_alloc_descs+0x2e4/0x3a0 irq_domain_alloc_descs+0xb0/0x150 irq_create_mapping+0x168/0x2c0 xics_smp_probe+0x2c/0x98 pnv_smp_probe+0x40/0x9c smp_prepare_cpus+0x524/0x6c4 kernel_init_freeable+0x1b4/0x650 kernel_init+0x2c/0x148 ret_from_kernel_thread+0x5c/0x70 INITIAL USE at: lock_acquire+0xf8/0x2a0 fs_reclaim_acquire.part.23+0x44/0x60 kmem_cache_alloc_node_trace+0x80/0x590 alloc_desc+0x64/0x270 __irq_alloc_descs+0x2e4/0x3a0 irq_domain_alloc_descs+0xb0/0x150 irq_create_mapping+0x168/0x2c0 xics_smp_probe+0x2c/0x98 pnv_smp_probe+0x40/0x9c smp_prepare_cpus+0x524/0x6c4 kernel_init_freeable+0x1b4/0x650 kernel_init+0x2c/0x148 ret_from_kernel_thread+0x5c/0x70 } === Signed-off-by:
Alexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by:
Alistair Popple <alistair@popple.id.au> Signed-off-by:
-
Lewis Huang authored
[ Upstream commit e5382701 ] [Why] The vm config will be clear to 0 when system enter S4. It will cause hubbub didn't know how to fetch data when system resume. The flip always pending because earliest_inuse_address and request_address are different. [How] Reprogram VM config when system resume Signed-off-by:
Lewis Huang <Lewis.Huang@amd.com> Reviewed-by:
Jun Lei <Jun.Lei@amd.com> Acked-by:
Eric Yang <eric.yang2@amd.com> Acked-by:
Leo Li <sunpeng.li@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Anthony Koo authored
[ Upstream commit 1cbcfc97 ] [Why] When endpoint is at the boundary of a region, such as at 2^0=1 we find that the last segment has a sharp slope and some points are clipped at the top. [How] If end point is 1, which is exactly at the 2^0 region boundary, we need to program an additional region beyond this point. Signed-off-by:
Anthony Koo <Anthony.Koo@amd.com> Reviewed-by:
Aric Cyr <Aric.Cyr@amd.com> Acked-by:
-
Icenowy Zheng authored
[ Upstream commit 72009960 ] The MMC2 clock slices are currently not defined in V3s CCU driver, which makes MMC2 not working. Fix this issue. Fixes: d0f11d14 ("clk: sunxi-ng: add support for V3s CCU") Signed-off-by:
Icenowy Zheng <icenowy@aosc.io> Signed-off-by:
Maxime Ripard <maxime.ripard@bootlin.com> Signed-off-by:
-
Nathan Huckleberry authored
[ Upstream commit a95fb581 ] drivers/clk/clk-qoriq.c:138:38: warning: unused variable 'p5020_cmux_grp1' [-Wunused-const-variable] static const struct clockgen_muxinfo p5020_cmux_grp1 drivers/clk/clk-qoriq.c:146:38: warning: unused variable 'p5020_cmux_grp2' [-Wunused-const-variable] static const struct clockgen_muxinfo p5020_cmux_grp2 In the definition of the p5020 chip, the p2041 chip's info was used instead. The p5020 and p2041 chips have different info. This is most likely a typo. Link: https://github.com/ClangBuiltLinux/linux/issues/525 Cc: clang-built-linux@googlegroups.com Signed-off-by:
Nathan Huckleberry <nhuck@google.com> Link: https://lkml.kernel.org/r/20190627220642.78575-1-nhuck@google.comReviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Acked-by:
Scott Wood <oss@buserror.net> Signed-off-by:
-
Corey Minyard authored
[ Upstream commit 340ff31a ] ipmi_thread() uses back-to-back schedule() to poll for command completion which, on some machines, can push up CPU consumption and heavily tax the scheduler locks leading to noticeable overall performance degradation. This was originally added so firmware updates through IPMI would complete in a timely manner. But we can't kill the scheduler locks for that one use case. Instead, only run schedule() continuously in maintenance mode, where firmware updates should run. Signed-off-by:
Corey Minyard <cminyard@mvista.com> Signed-off-by:
-
Nathan Chancellor authored
[ Upstream commit 0df3e421 ] When building with -Wsometimes-uninitialized, clang warns: drivers/pci/hotplug/rpaphp_core.c:243:14: warning: variable 'fndit' is used uninitialized whenever 'for' loop exits because its condition is false [-Wsometimes-uninitialized] for (j = 0; j < entries; j++) { ^~~~~~~~~~~ drivers/pci/hotplug/rpaphp_core.c:256:6: note: uninitialized use occurs here if (fndit) ^~~~~ drivers/pci/hotplug/rpaphp_core.c:243:14: note: remove the condition if it is always true for (j = 0; j < entries; j++) { ^~~~~~~~~~~ drivers/pci/hotplug/rpaphp_core.c:233:14: note: initialize the variable 'fndit' to silence this warning int j, fndit; ^ = 0 fndit is only used to gate a sprintf call, which can be moved into the loop to simplify the code and eliminate the local variable, which will fix this warning. Fixes: 2fcf3ae5 ("hotplug/drc-info: Add code to search ibm,drc-info property") Suggested-by:
Nathan Chancellor <natechancellor@gmail.com> Acked-by:
Tyrel Datwyler <tyreld@linux.ibm.com> Acked-by:
Joel Savitz <jsavitz@redhat.com> Signed-off-by:
-
Jia-Ju Bai authored
[ Upstream commit f3eb9b8f ] In radeon_connector_set_property(), there is an if statement on line 743 to check whether connector->encoder is NULL: if (connector->encoder) When connector->encoder is NULL, it is used on line 755: if (connector->encoder->crtc) Thus, a possible null-pointer dereference may occur. To fix this bug, connector->encoder is checked before being used. This bug is found by a static analysis tool STCheck written by us. Signed-off-by:
Jia-Ju Bai <baijiaju1990@gmail.com> Signed-off-by:
-
KyleMahlkuch authored
[ Upstream commit 6f7fe9a9 ] During kexec some adapters hit an EEH since they are not properly shut down in the radeon_pci_shutdown() function. Adding radeon_suspend_kms() fixes this issue. Signed-off-by:
KyleMahlkuch <kmahlkuc@linux.vnet.ibm.com> Signed-off-by:
-
Sean Paul authored
[ Upstream commit ad309284 ] Once we start shutting off the link during PSR, we're going to want fast training to work. If the display doesn't support fast training, don't enable psr. Changes in v2: - None Changes in v3: - None Changes in v4: - None Changes in v5: - None Link to v1: https://patchwork.freedesktop.org/patch/msgid/20190228210939.83386-3-sean@poorly.run Link to v2: https://patchwork.freedesktop.org/patch/msgid/20190326204509.96515-2-sean@poorly.run Link to v3: https://patchwork.freedesktop.org/patch/msgid/20190502194956.218441-9-sean@poorly.run Link to v4: https://patchwork.freedesktop.org/patch/msgid/20190508160920.144739-8-sean@poorly.run Cc: Zain Wang <wzz@rock-chips.com> Cc: Tomasz Figa <tfiga@chromium.org> Tested-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
Sean Paul <seanpaul@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190611160844.257498-8-sean@poorly.runSigned-off-by:
-
Navid Emamdoost authored
[ Upstream commit afd6d4f5 ] The following function calls may fail and return NULL, so the null check is added. of_graph_get_next_endpoint of_graph_get_remote_port_parent of_graph_get_remote_port Update: Thanks to Sam Ravnborg, for suggession on the use of goto to avoid leaking endpoint. Signed-off-by:
Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by:
Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190724195534.9303-1-navid.emamdoost@gmail.comSigned-off-by:
-
Ahmad Fatoum authored
[ Upstream commit 8fabc9c3 ] To properly synchronize with other devices the fence from the GEM object backing the framebuffer needs to be attached to the atomic state, so the commit work can wait on fence signaling. Signed-off-by:
Ahmad Fatoum <a.fatoum@pengutronix.de> Signed-off-by:
Lucas Stach <l.stach@pengutronix.de> Acked-by:
Philippe Cornu <philippe.cornu@st.com> Tested-by:
Benjamin Gaignard <benjamin.gaignard@linaro.org> Link: https://patchwork.freedesktop.org/patch/msgid/20190712084228.8338-1-l.stach@pengutronix.deSigned-off-by:
-
Marko Kohtala authored
[ Upstream commit dd978283 ] The page_offset was only applied to the end of the page range. This caused the display updates to cause a scrolling effect on the display because the amount of data written to the display did not match the range display expected. Fixes: 301bc067 ("video: ssd1307fb: Make use of horizontal addressing mode") Signed-off-by:
Marko Kohtala <marko.kohtala@okoko.fi> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Rob Herring <robh+dt@kernel.org> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: David Airlie <airlied@linux.ie> Cc: Michal Vokáč <michal.vokac@ysoft.com> Signed-off-by:
Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190618074111.9309-4-marko.kohtala@okoko.fiSigned-off-by:
-
Lucas Stach authored
[ Upstream commit f8c6bfc6 ] The horizontal blanking periods are too short, as the values are specified for a single LVDS channel. Since this panel is dual LVDS they need to be doubled. With this change the panel reaches its nominal vrefresh rate of 60Fps, instead of the 64Fps with the current wrong blanking. Philipp Zabel added: The datasheet specifies 960 active clocks + 40/128/160 clocks blanking on each of the two LVDS channels (min/typical/max), so doubled this is now correct. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by:
-
Andrey Smirnov authored
[ Upstream commit e0655fea ] According to the datasheet tc358767 can transfer up to 16 bytes via its AUX channel, so the artificial limit of 8 appears to be too low. However only up to 15-bytes seem to be actually supported and trying to use 16-byte transfers results in transfers failing sporadically (with bogus status in case of I2C transfers), so limit it to 15. Signed-off-by:
Andrey Smirnov <andrew.smirnov@gmail.com> Reviewed-by:
Andrzej Hajda <a.hajda@samsung.com> Reviewed-by:
Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Andrzej Hajda <a.hajda@samsung.com> Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com> Cc: Philipp Zabel <p.zabel@pengutronix.de> Cc: Cory Tusar <cory.tusar@zii.aero> Cc: Chris Healy <cphealy@gmail.com> Cc: Lucas Stach <l.stach@pengutronix.de> Cc: dri-devel@lists.freedesktop.org Cc: linux-kernel@vger.kernel.org Signed-off-by:
-
Vadim Sukhomlinov authored
commit db4d8cb9 upstream TPM 2.0 Shutdown involve sending TPM2_Shutdown to TPM chip and disabling future TPM operations. TPM 1.2 behavior was different, future TPM operations weren't disabled, causing rare issues. This patch ensures that future TPM operations are disabled. Fixes: d1bd4a79 ("tpm: Issue a TPM2_Shutdown for TPM2 devices.") Cc: stable@vger.kernel.org Signed-off-by:
Vadim Sukhomlinov <sukhomlinov@google.com> [dianders: resolved merge conflicts with mainline] Signed-off-by:
Douglas Anderson <dianders@chromium.org> Reviewed-by:
Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com> Signed-off-by:
-
Jarkko Sakkinen authored
commit 2677ca98 upstream Use tpm_try_get_ops() in tpm-sysfs.c so that we can consider moving other decorations (locking, localities, power management for example) inside it. This direction can be of course taken only after other call sites for tpm_transmit() have been treated in the same way. Signed-off-by:
Stefan Berger <stefanb@linux.ibm.com> Tested-by:
Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by:
James Bottomley <James.Bottomley@HansenPartnership.com> Tested-by:
Alexander Steffen <Alexander.Steffen@infineon.com> Signed-off-by:
-
- 05 Oct, 2019 10 commits
-
-
Greg Kroah-Hartman authored
-
Kai-Heng Feng authored
commit bb264220 upstream. Laptops with AMD APU doesn't restore display backlight brightness after system resume. This issue started when DC was introduced. Let's use BL_CORE_SUSPENDRESUME so the backlight core calls update_status callback after system resume to restore the backlight level. Tested on Dell Inspiron 3180 (Stoney Ridge) and Dell Latitude 5495 (Raven Ridge). Cc: <stable@vger.kernel.org> Signed-off-by:
Kai-Heng Feng <kai.heng.feng@canonical.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Yafang Shao authored
[ Upstream commit a94b5252 ] total_{migrate,free}_scanned will be added to COMPACTMIGRATE_SCANNED and COMPACTFREE_SCANNED in compact_zone(). We should clear them before scanning a new zone. In the proc triggered compaction, we forgot clearing them. [laoar.shao@gmail.com: introduce a helper compact_zone_counters_init()] Link: http://lkml.kernel.org/r/1563869295-25748-1-git-send-email-laoar.shao@gmail.com [akpm@linux-foundation.org: expand compact_zone_counters_init() into its single callsite, per mhocko] [vbabka@suse.cz: squash compact_zone() list_head init as well] Link: http://lkml.kernel.org/r/1fb6f7da-f776-9e42-22f8-bbb79b030b98@suse.cz [akpm@linux-foundation.org: kcompactd_do_work(): avoid unnecessary initialization of cc.zone] Link: http://lkml.kernel.org/r/1563789275-9639-1-git-send-email-laoar.shao@gmail.com Fixes: 7f354a54 ("mm, compaction: add vmstats for kcompactd work") Signed-off-by:
Yafang Shao <laoar.shao@gmail.com> Signed-off-by:
Vlastimil Babka <vbabka@suse.cz> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Eric Biggers authored
[ Upstream commit 76e43c8c ] When IOCB_CMD_POLL is used on the FUSE device, aio_poll() disables IRQs and takes kioctx::ctx_lock, then fuse_iqueue::waitq.lock. This may have to wait for fuse_iqueue::waitq.lock to be released by one of many places that take it with IRQs enabled. Since the IRQ handler may take kioctx::ctx_lock, lockdep reports that a deadlock is possible. Fix it by protecting the state of struct fuse_iqueue with a separate spinlock, and only accessing fuse_iqueue::waitq using the versions of the waitqueue functions which do IRQ-safe locking internally. Reproducer: #include <fcntl.h> #include <stdio.h> #include <sys/mount.h> #include <sys/stat.h> #include <sys/syscall.h> #include <unistd.h> #include <linux/aio_abi.h> int main() { char opts[128]; int fd = open("/dev/fuse", O_RDWR); aio_context_t ctx = 0; struct iocb cb = { .aio_lio_opcode = IOCB_CMD_POLL, .aio_fildes = fd }; struct iocb *cbp = &cb; sprintf(opts, "fd=%d,rootmode=040000,user_id=0,group_id=0", fd); mkdir("mnt", 0700); mount("foo", "mnt", "fuse", 0, opts); syscall(__NR_io_setup, 1, &ctx); syscall(__NR_io_submit, ctx, 1, &cbp); } Beginning of lockdep output: ===================================================== WARNING: SOFTIRQ-safe -> SOFTIRQ-unsafe lock order detected 5.3.0-rc5 #9 Not tainted ----------------------------------------------------- syz_fuse/135 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire: 000000003590ceda (&fiq->waitq){+.+.}, at: spin_lock include/linux/spinlock.h:338 [inline] 000000003590ceda (&fiq->waitq){+.+.}, at: aio_poll fs/aio.c:1751 [inline] 000000003590ceda (&fiq->waitq){+.+.}, at: __io_submit_one.constprop.0+0x203/0x5b0 fs/aio.c:1825 and this task is already holding: 0000000075037284 (&(&ctx->ctx_lock)->rlock){..-.}, at: spin_lock_irq include/linux/spinlock.h:363 [inline] 0000000075037284 (&(&ctx->ctx_lock)->rlock){..-.}, at: aio_poll fs/aio.c:1749 [inline] 0000000075037284 (&(&ctx->ctx_lock)->rlock){..-.}, at: __io_submit_one.constprop.0+0x1f4/0x5b0 fs/aio.c:1825 which would create a new lock dependency: (&(&ctx->ctx_lock)->rlock){..-.} -> (&fiq->waitq){+.+.} but this new dependency connects a SOFTIRQ-irq-safe lock: (&(&ctx->ctx_lock)->rlock){..-.} [...] Reported-by: syzbot+af05535bb79520f95431@syzkaller.appspotmail.com Reported-by: syzbot+d86c4426a01f60feddc7@syzkaller.appspotmail.com Fixes: bfe4037e ("aio: implement IOCB_CMD_POLL") Cc: <stable@vger.kernel.org> # v4.19+ Cc: Christoph Hellwig <hch@lst.de> Signed-off-by:
Eric Biggers <ebiggers@google.com> Signed-off-by:
Miklos Szeredi <mszeredi@redhat.com> Signed-off-by:
-
NeilBrown authored
[ Upstream commit c84a1372 ] If the drives in a RAID0 are not all the same size, the array is divided into zones. The first zone covers all drives, to the size of the smallest. The second zone covers all drives larger than the smallest, up to the size of the second smallest - etc. A change in Linux 3.14 unintentionally changed the layout for the second and subsequent zones. All the correct data is still stored, but each chunk may be assigned to a different device than in pre-3.14 kernels. This can lead to data corruption. It is not possible to determine what layout to use - it depends which kernel the data was written by. So we add a module parameter to allow the old (0) or new (1) layout to be specified, and refused to assemble an affected array if that parameter is not set. Fixes: 20d0189b ("block: Introduce new bio_split()") cc: stable@vger.kernel.org (3.14+) Acked-by:
Guoqing Jiang <guoqing.jiang@cloud.ionos.com> Signed-off-by:
NeilBrown <neilb@suse.de> Signed-off-by:
Song Liu <songliubraving@fb.com> Signed-off-by:
-
Pavel Shilovsky authored
commit a016e279 upstream. There may be situations when a server negotiates SMB 2.1 protocol version or higher but responds to a CREATE request with an oplock rather than a lease. Currently the client doesn't handle such a case correctly: when another CREATE comes in the server sends an oplock break to the initial CREATE and the client doesn't send an ack back due to a wrong caching level being set (READ instead of RWH). Missing an oplock break ack makes the server wait until the break times out which dramatically increases the latency of the second CREATE. Fix this by properly detecting oplocks when using SMB 2.1 protocol version and higher. Cc: <stable@vger.kernel.org> Signed-off-by:
Pavel Shilovsky <pshilov@microsoft.com> Signed-off-by:
Steve French <stfrench@microsoft.com> Reviewed-by:
Ronnie Sahlberg <lsahlber@redhat.com> Signed-off-by:
-
Murphy Zhou authored
commit 63d37fb4 upstream. It should not be larger then the slab max buf size. If user specifies a larger size, it passes this check and goes straightly to SMB2_set_info_init performing an insecure memcpy. Signed-off-by:
Murphy Zhou <jencce.kernel@gmail.com> Reviewed-by:
Aurelien Aptel <aaptel@suse.com> CC: Stable <stable@vger.kernel.org> Signed-off-by:
-
Chris Brandt authored
commit a71e2ac1 upstream. The NACKF flag should be cleared in INTRIICNAKI interrupt processing as description in HW manual. This issue shows up quickly when PREEMPT_RT is applied and a device is probed that is not plugged in (like a touchscreen controller). The result is endless interrupts that halt system boot. Fixes: 310c18a4 ("i2c: riic: add driver") Cc: stable@vger.kernel.org Reported-by:
Chien Nguyen <chien.nguyen.eb@rvc.renesas.com> Signed-off-by:
Chris Brandt <chris.brandt@renesas.com> Signed-off-by:
Wolfram Sang <wsa@the-dreams.de> Signed-off-by:
-
Laurent Vivier authored
commit 78887832 upstream. add_early_randomness() is called by hwrng_register() when the hardware is added. If this hardware and its module are present at boot, and if there is no data available the boot hangs until data are available and can't be interrupted. For instance, in the case of virtio-rng, in some cases the host can be not able to provide enough entropy for all the guests. We can have two easy ways to reproduce the problem but they rely on misconfiguration of the hypervisor or the egd daemon: - if virtio-rng device is configured to connect to the egd daemon of the host but when the virtio-rng driver asks for data the daemon is not connected, - if virtio-rng device is configured to connect to the egd daemon of the host but the egd daemon doesn't provide data. The guest kernel will hang at boot until the virtio-rng driver provides enough data. To avoid that, call rng_get_data() in non-blocking mode (wait=0) from add_early_randomness(). Signed-off-by:
Laurent Vivier <lvivier@redhat.com> Fixes: d9e79726 ("hwrng: add randomness to system from rng...") Cc: <stable@vger.kernel.org> Reviewed-by:
Theodore Ts'o <tytso@mit.edu> Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Chao Yu authored
commit 6565c182 upstream. Quoted from commit 3da40c7b ("ext4: only call ext4_truncate when size <= isize") " At LSF we decided that if we truncate up from isize we shouldn't trim fallocated blocks that were fallocated with KEEP_SIZE and are past the new i_size. This patch fixes ext4 to do this. " And generic/092 of fstest have covered this case for long time, however is_quota_modification() didn't adjust based on that rule, so that in below condition, we will lose to quota block change: - fallocate blocks beyond EOF - remount - truncate(file_path, file_size) Fix it. Link: https://lore.kernel.org/r/20190911093650.35329-1-yuchao0@huawei.com Fixes: 3da40c7b ("ext4: only call ext4_truncate when size <= isize") CC: stable@vger.kernel.org Signed-off-by:
Chao Yu <yuchao0@huawei.com> Signed-off-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
