In 5GHz/802.11a, we are allowed to use short slot times. Doing this
may increases performance by 20% for legacy connections (54 MBit/s).
I can confirm this in my tests (27% more throughput using iperf), and
also have a small positive effect (5% more throughput) for HT rates,
tested on 1 stream.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Mathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix an error on mesh join when no channel has been
explicitly set beforehand.

Also remove a double semicolon.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If channel contexts are enabled, the CSA should not be processed
further. A return is missing here.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When a BSS struct is updated, the IEs are currently
overwritten or freed. This can lead to races if some
other CPU is accessing the BSS struct and using the
IEs concurrently.

Fix this by always allocating the IEs in a new struct
that holds the data and length and protecting access
to this new struct with RCU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of allocating a temporary buffer to build IEs
build them right into the SKB.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of assuming 200 bytes are always enough for
all the IEs we add, give the length of the buffer
to the function and warn instead of overrunning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The cmp_bss() comparator function uses memcmp() to
compare the SSID. This means that cmp_hidden_bss()
needs to similarly return a number bigger than zero
(use 1) instead of -1 when ie1 is bigger than ie2,
which is the case if an ie2 byte is non-zero.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Fix a number of indentation and similar issues.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There's no need to stop the machine, just leak
the BSS entry if there's an issue with its hold
counter when freeing.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This change allows userspace to register for probe request
frames on an IBSS interface. Userspace then has to handle
them and send replies.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently the mesh sync code checks, whether peers indicate TBTT adjustment,
but it never sets the corresponding flag itself.

By setting ifmsh->tbtt_adjusting to true, it will set the corresponding field
in the mesh configuration IE of own beacons.
This indication will be set in the current beacon. The TBTT adjustment will be
performed afterwards, affecting the next beacon. Thus, the first beacon with
stable TBTT will not indicate adjustment anymore and peers will continue
tracking the new offset.
Signed-off-by: Marco Porsch <marco.porsch@etit.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There is a standalone if, seems to be a regression of commit
"nl80211/cfg80211: add VHT MCS support".
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a debugfs file showing the rate at which
the last packet is received.
Signed-off-by: Saravana <saravanad@posedge.com>
[fix whitespace]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Currently the logic to fill a struct rate_info with
a STA's last RX rate is accessible only in the cfg.c.
As the RX rate calculation might be needed elsewhere,
split this out into a separate function.
Signed-off-by: Saravana <saravanad@posedge.com>
[fix various whitespace issues, reword commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a debugfs file showing the current tx rate.
The information available in the rc_stats file
doesn't evidently provides us the current tx rate.
This patch adds the support for the same.
Signed-off-by: Saravana <saravanad@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add a debugfs file showing the signal strength
of the ack frame that is received for the
currently sent tx packet
Signed-off-by: Saravana <saravanad@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Cleanup of unused VHT channel config related code.
Signed-off-by: Mahesh Palivela <maheshp@posedge.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This fixes some unintended resets of the rate control statistics
when minstrel_ht is used resulting in non-optimal throughput on mesh
links.
Tested-by: Emanuel Taube <emanuel.taube@gmail.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If a driver registers an address mask we should ensure that no
interface gets an address assigned that isn't covered by the
registered address mask. This prevents invalid configurations
from reaching the device and causing problems.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
[change function flow to reduce indentation, fix locking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Smatch complains that we could dereference skb later in the function.
It's probably unlikely, but we may as well return here and avoid it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[change summary]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The CQM TX-error rate/interval can't be less than
zero since they're unsigned values, remove checks.
Also fix indentation of the function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the low-level driver wants to support P2P GO
powersave configuration, it must set the cfg80211
flags and mac80211 will pass the parameters to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If a driver supports P2P GO powersave, allow it to
set the new feature flags for it and allow userspace
to configure the parameters for it. This can be done
at GO startup and later changed with SET_BSS.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add some information that we have about VHT to radiotap.
This at least lets one see the MCS and NSS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Determine the VHT channel from the AP's VHT operation IE
(if present) and configure the hardware to that channel
if it is supported. If channel contexts cause a channel
to not be usable, try a smaller bandwidth.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some of the chandef checking that we do in cfg80211
to check if a channel is supported or not is also
needed in mac80211, so rework that a bit and export
the functions that are needed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In some cases, e.g. probe_status, there were spaces
missing so the trace output was confusing. Also make
it more like mac80211 when printing netdevs/wiphys
to make reading a combined log easier.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The frequencies will be printed when actually
doing the scan, and the IEs can be captured
on the hwsim0 monitor.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

If the number of channels is > 1, which means that
hwsim will use mac80211 channel contexts, it can
also advertise VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add definitions for the VHT MCS support values that
are used to indicate, for each number of streams
(1 through 8) which MCSes are supported.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To achieve this, limit the number of retries to
31 (instead of 255) and use the three bits that
are then free for VHT flags.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add support to mac80211 for having drivers report
received VHT MCS information.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add support for reporting and calculating VHT MCSes.

Note that I'm not completely sure that the bitrate
calculations are correct, nor that they can't be
simplified.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>