- 08 Jul, 2018 39 commits
-
-
NeilBrown authored
commit b03e0ccb upstream. The '2' argument means "wake up anything that is waiting". This is an inelegant part of the design and was added to help support management of suspend_lo/suspend_hi setting. Now that suspend_lo/hi is managed in mddev_suspend/resume, that need is gone. These is still a couple of places where we call 'quiesce' with an argument of '2', but they can safely be changed to call ->quiesce(.., 1); ->quiesce(.., 0) which achieve the same result at the small cost of pausing IO briefly. This removes a small "optimization" from suspend_{hi,lo}_store, but it isn't clear that optimization served a useful purpose. The code now is a lot clearer. Suggested-by:
Shaohua Li <shli@kernel.org> Signed-off-by:
NeilBrown <neilb@suse.com> Signed-off-by:
Shaohua Li <shli@fb.com> Signed-off-by:
Jack Wang <jinpu.wang@profitbricks.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
NeilBrown authored
commit 35bfc521 upstream. There are various deadlocks that can occur when a thread holds reconfig_mutex and calls ->quiesce(mddev, 1). As some write request block waiting for metadata to be updated (e.g. to record device failure), and as the md thread updates the metadata while the reconfig mutex is held, holding the mutex can stop write requests completing, and this prevents ->quiesce(mddev, 1) from completing. ->quiesce() is now usually called from mddev_suspend(), and it is always called with reconfig_mutex held. So at this time it is safe for the thread to update metadata without explicitly taking the lock. So add 2 new flags, one which says the unlocked updates is allowed, and one which ways it is happening. Then allow it while the quiesce completes, and then wait for it to finish. Reported-and-tested-by:
Xiao Ni <xni@redhat.com> Signed-off-by:
-
NeilBrown authored
commit 9e1cc0a5 upstream. mddev_suspend() is a more general interface than calling ->quiesce() and is so more extensible. A future patch will make use of this. Signed-off-by:
-
NeilBrown authored
commit b3143b9a upstream. responding to ->suspend_lo and ->suspend_hi is similar to responding to ->suspended. It is best to wait in the common core code without incrementing ->active_io. This allows mddev_suspend()/mddev_resume() to work while requests are waiting for suspend_lo/hi to change. This is will be important after a subsequent patch which uses mddev_suspend() to synchronize updating for suspend_lo/hi. So move the code for testing suspend_lo/hi out of raid1.c and raid5.c, and place it in md.c Signed-off-by:
-
NeilBrown authored
commit 52a0d49d upstream. bitmap_create() allocates memory with GFP_KERNEL and so can wait for IO. If called while the array is quiesced, it could wait indefinitely for write out to the array - deadlock. So call bitmap_create() before quiescing the array. Signed-off-by:
-
NeilBrown authored
commit 4d5324f7 upstream. Most often mddev_suspend() is called with reconfig_mutex held. Make this a requirement in preparation a subsequent patch. Also require reconfig_mutex to be held for mddev_resume(), partly for symmetry and partly to guarantee no races with incr/decr of mddev->suspend. Taking the mutex in r5c_disable_writeback_async() is a little tricky as this is called from a work queue via log->disable_writeback_work, and flush_work() is called on that while holding ->reconfig_mutex. If the work item hasn't run before flush_work() is called, the work function will not be able to get the mutex. So we use mddev_trylock() inside the wait_event() call, and have that abort when conf->log is set to NULL, which happens before flush_work() is called. We wait in mddev->sb_wait and ensure this is woken when any of the conditions change. This requires waking mddev->sb_wait in mddev_unlock(). This is only like to trigger extra wake_ups of threads that needn't be woken when metadata is being written, and that doesn't happen often enough that the cost would be noticeable. Signed-off-by:
-
Taehee Yoo authored
commit 360cc79d upstream. The table field in nft_obj_filter is not an array. In order to check tablename, we should check if the pointer is set. Test commands: %nft add table ip filter %nft add counter ip filter ct1 %nft reset counters Splat looks like: [ 306.510504] kasan: CONFIG_KASAN_INLINE enabled [ 306.516184] kasan: GPF could be caused by NULL-ptr deref or user memory access [ 306.524775] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI [ 306.528284] Modules linked in: nft_objref nft_counter nf_tables nfnetlink ip_tables x_tables [ 306.528284] CPU: 0 PID: 1488 Comm: nft Not tainted 4.17.0-rc4+ #17 [ 306.528284] Hardware name: To be filled by O.E.M. To be filled by O.E.M./Aptio CRB, BIOS 5.6.5 07/08/2015 [ 306.528284] RIP: 0010:nf_tables_dump_obj+0x52c/0xa70 [nf_tables] [ 306.528284] RSP: 0018:ffff8800b6cb7520 EFLAGS: 00010246 [ 306.528284] RAX: 0000000000000000 RBX: ffff8800b6c49820 RCX: 0000000000000000 [ 306.528284] RDX: 0000000000000000 RSI: dffffc0000000000 RDI: ffffed0016d96e9a [ 306.528284] RBP: ffff8800b6cb75c0 R08: ffffed00236fce7c R09: ffffed00236fce7b [ 306.528284] R10: ffffffff9f6241e8 R11: ffffed00236fce7c R12: ffff880111365108 [ 306.528284] R13: 0000000000000000 R14: ffff8800b6c49860 R15: ffff8800b6c49860 [ 306.528284] FS: 00007f838b007700(0000) GS:ffff88011b600000(0000) knlGS:0000000000000000 [ 306.528284] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 306.528284] CR2: 00007ffeafabcf78 CR3: 00000000b6cbe000 CR4: 00000000001006f0 [ 306.528284] Call Trace: [ 306.528284] netlink_dump+0x470/0xa20 [ 306.528284] __netlink_dump_start+0x5ae/0x690 [ 306.528284] ? nf_tables_getobj+0x1b3/0x740 [nf_tables] [ 306.528284] nf_tables_getobj+0x2f5/0x740 [nf_tables] [ 306.528284] ? nft_obj_notify+0x100/0x100 [nf_tables] [ 306.528284] ? nf_tables_getobj+0x740/0x740 [nf_tables] [ 306.528284] ? nf_tables_dump_flowtable_done+0x70/0x70 [nf_tables] [ 306.528284] ? nft_obj_notify+0x100/0x100 [nf_tables] [ 306.528284] nfnetlink_rcv_msg+0x8ff/0x932 [nfnetlink] [ 306.528284] ? nfnetlink_rcv_msg+0x216/0x932 [nfnetlink] [ 306.528284] netlink_rcv_skb+0x1c9/0x2f0 [ 306.528284] ? nfnetlink_bind+0x1d0/0x1d0 [nfnetlink] [ 306.528284] ? debug_check_no_locks_freed+0x270/0x270 [ 306.528284] ? netlink_ack+0x7a0/0x7a0 [ 306.528284] ? ns_capable_common+0x6e/0x110 [ ... ] Fixes: e46abbcc ("netfilter: nf_tables: Allow table names of up to 255 chars") Signed-off-by:
Taehee Yoo <ap420073@gmail.com> Acked-by:
Florian Westphal <fw@strlen.de> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Florian Westphal authored
commit 467697d2 upstream. Fixes: 8aeff920 ("netfilter: nf_tables: add stateful object reference to set elements") Fixes: f25ad2e9 ("netfilter: nf_tables: prepare for expressions associated to set elements") Fixes: 1a94e38d ("netfilter: nf_tables: add NFTA_RULE_ID attribute") Signed-off-by:
-
Colin Ian King authored
commit f0dfd7a2 upstream. Currently the -EBUSY error return path is not free'ing resources allocated earlier, leaving a memory leak. Fix this by exiting via the error exit label err5 that performs the necessary resource clean up. Detected by CoverityScan, CID#1432975 ("Resource leak") Fixes: 9744a6fc ("netfilter: nf_tables: check if same extensions are set when adding elements") Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Taehee Yoo authored
commit bbb8c61f upstream. When a chain is updated, a counter can be attached. if so, the nft_counters_enabled should be increased. test commands: %nft add table ip filter %nft add chain ip filter input { type filter hook input priority 4\; } %iptables-compat -Z input %nft delete chain ip filter input we can see below messages. [ 286.443720] jump label: negative count! [ 286.448278] WARNING: CPU: 0 PID: 1459 at kernel/jump_label.c:197 __static_key_slow_dec_cpuslocked+0x6f/0xf0 [ 286.449144] Modules linked in: nf_tables nfnetlink ip_tables x_tables [ 286.449144] CPU: 0 PID: 1459 Comm: nft Tainted: G W 4.17.0-rc2+ #12 [ 286.449144] RIP: 0010:__static_key_slow_dec_cpuslocked+0x6f/0xf0 [ 286.449144] RSP: 0018:ffff88010e5176f0 EFLAGS: 00010286 [ 286.449144] RAX: 000000000000001b RBX: ffffffffc0179500 RCX: ffffffffb8a82522 [ 286.449144] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88011b7e5eac [ 286.449144] RBP: 0000000000000000 R08: ffffed00236fce5c R09: ffffed00236fce5b [ 286.449144] R10: ffffffffc0179503 R11: ffffed00236fce5c R12: 0000000000000000 [ 286.449144] R13: ffff88011a28e448 R14: ffff88011a28e470 R15: dffffc0000000000 [ 286.449144] FS: 00007f0384328700(0000) GS:ffff88011b600000(0000) knlGS:0000000000000000 [ 286.449144] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 286.449144] CR2: 00007f038394bf10 CR3: 0000000104a86000 CR4: 00000000001006f0 [ 286.449144] Call Trace: [ 286.449144] static_key_slow_dec+0x6a/0x70 [ 286.449144] nf_tables_chain_destroy+0x19d/0x210 [nf_tables] [ 286.449144] nf_tables_commit+0x1891/0x1c50 [nf_tables] [ 286.449144] nfnetlink_rcv+0x1148/0x13d0 [nfnetlink] [ ... ] Signed-off-by:
-
Pablo Neira Ayuso authored
commit ad9d9e85 upstream. This patch fixes the following splat. [118709.054937] BUG: using smp_processor_id() in preemptible [00000000] code: test/1571 [118709.054970] caller is nft_update_chain_stats.isra.4+0x53/0x97 [nf_tables] [118709.054980] CPU: 2 PID: 1571 Comm: test Not tainted 4.17.0-rc6+ #335 [...] [118709.054992] Call Trace: [118709.055011] dump_stack+0x5f/0x86 [118709.055026] check_preemption_disabled+0xd4/0xe4 Signed-off-by:
-
Taehee Yoo authored
commit 97a0549b upstream. In the nft_meta_set_eval, nftrace value is dereferenced as u32 from sreg. But correct type is u8. so that sometimes incorrect value is dereferenced. Steps to reproduce: %nft add table ip filter %nft add chain ip filter input { type filter hook input priority 4\; } %nft add rule ip filter input nftrace set 0 %nft monitor Sometimes, we can see trace messages. trace id 16767227 ip filter input packet: iif "enp2s0" ether saddr xx:xx:xx:xx:xx:xx ether daddr xx:xx:xx:xx:xx:xx ip saddr 192.168.0.1 ip daddr 255.255.255.255 ip dscp cs0 ip ecn not-ect ip trace id 16767227 ip filter input rule nftrace set 0 (verdict continue) trace id 16767227 ip filter input verdict continue trace id 16767227 ip filter input Signed-off-by:
-
Pablo Neira Ayuso authored
commit bb7b40ae upstream. When removing a rule that jumps to chain and such chain in the same batch, this bogusly hits EBUSY. Add activate and deactivate operations to expression that can be called from the preparation and the commit/abort phases. Signed-off-by:
-
Florian Westphal authored
commit 00924094 upstream. nft_chain_stats_replace() and all other spots assume ->stats can be NULL, but nft_update_chain_stats does not. It must do this check, just because the jump label is set doesn't mean all basechains have stats assigned. Signed-off-by:
-
Florian Westphal authored
commit 732a8049 upstream. currently matchinfo gets stored in the expression, but some xt matches are very large. To handle those we either need to switch nft core to kvmalloc and increase size limit, or allocate the info blob of large matches separately. This does the latter, this limits the scope of the changes to nft_compat. I picked a threshold of 192, this allows most matches to work as before and handle only few ones via separate alloation (cgroup, u32, sctp, rt). Signed-off-by:
-
Florian Westphal authored
commit 8bdf1647 upstream. Next patch will make it possible for *info to be stored in a separate allocation instead of the expr private area. This removes the 'expr priv area is info blob' assumption from the match init/destroy/eval functions. Signed-off-by:
-
Florian Westphal authored
commit b8e9dc1c upstream. Taehee Yoo reported following bug: iptables-compat -I OUTPUT -m cpu --cpu 0 iptables-compat -F lsmod |grep xt_cpu xt_cpu 16384 1 Quote: "When above command is given, a netlink message has two expressions that are the cpu compat and the nft_counter. The nft_expr_type_get() in the nf_tables_expr_parse() successes first expression then, calls select_ops callback. (allocates memory and holds module) But, second nft_expr_type_get() in the nf_tables_expr_parse() returns -EAGAIN because of request_module(). In that point, by the 'goto err1', the 'module_put(info[i].ops->type->owner)' is called. There is no release routine." The core problem is that unlike all other expression, nft_compat select_ops has side effects. 1. it allocates dynamic memory which holds an nft ops struct. In all other expressions, ops has static storage duration. 2. It grabs references to the xt module that it is supposed to invoke. Depending on where things go wrong, error unwinding doesn't always do the right thing. In the above scenario, a new nft_compat_expr is created and xt_cpu module gets loaded with a refcount of 1. Due to to -EAGAIN, the netlink messages get re-parsed. When that happens, nft_compat finds that xt_cpu is already present and increments module refcount again. This fixes the problem by making select_ops to have no visible side effects and removes all extra module_get/put. When select_ops creates a new nft_compat expression, the new expression has a refcount of 0, and the xt module gets its refcount incremented. When error happens, the next call finds existing entry, but will no longer increase the reference count -- the presence of existing nft_xt means we already hold a module reference. Because nft_xt_put is only called from nft_compat destroy hook, it will never see the initial zero reference count. ->destroy can only be called after ->init(), and that will increase the refcount. Lastly, we now free nft_xt struct with kfree_rcu. Else, we get use-after free in nf_tables_rule_destroy: while (expr != nft_expr_last(rule) && expr->ops) { nf_tables_expr_destroy(ctx, expr); expr = nft_expr_next(expr); // here nft_expr_next() dereferences expr->ops. This is safe for all users, as ops have static storage duration. In nft_compat case however, its ->destroy callback can free the memory that hold the ops structure. Tested-by:
-
Kenneth Graunke authored
commit 7a3727f3 upstream. The SF and clipper units mishandle the provoking vertex in some cases, which can cause misrendering with shaders that use flat shaded inputs. There are chicken bits in 3D_CHICKEN3 (for SF) and FF_SLICE_CHICKEN (for the clipper) that work around the issue. These registers are unfortunately not part of the logical context (even the power context), and so we must reload them every time we start executing in a context. Bugzilla: https://bugs.freedesktop.org/103047Signed-off-by:
Kenneth Graunke <kenneth@whitecape.org> Signed-off-by:
Chris Wilson <chris@chris-wilson.co.uk> Link: https://patchwork.freedesktop.org/patch/msgid/20180615190605.16238-1-chris@chris-wilson.co.ukReviewed-by:
Joonas Lahtinen <joonas.lahtinen@linux.intel.com> Cc: stable@vger.kernel.org (cherry picked from commit b77422f8) Signed-off-by:
Jani Nikula <jani.nikula@intel.com> Signed-off-by:
-
Michel Dänzer authored
commit 5e9244ff upstream. Preparation for the following fix, no functional change intended. Cc: stable@vger.kernel.org Signed-off-by:
Michel Dänzer <michel.daenzer@amd.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Michel Dänzer authored
commit 6fa39bc1 upstream. It can be quite big, and there's no need for it to be physically contiguous. This is less likely to fail under memory pressure (has actually happened while running piglit). Cc: stable@vger.kernel.org Signed-off-by:
-
Stefan Agner authored
commit 9fcf2b3c upstream. The statement always evaluates to true since the struct fields are arrays. This has shown up as a warning when compiling with clang: warning: address of array 'desc->layout.xstride' will always evaluate to 'true' [-Wpointer-bool-conversion] Check for values in the first plane instead. Fixes: 1a396789 ("drm: add Atmel HLCDC Display Controller support") Cc: <stable@vger.kernel.org> Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
Boris Brezillon <boris.brezillon@bootlin.com> Link: https://patchwork.freedesktop.org/patch/msgid/20180617084826.31885-1-stefan@agner.chSigned-off-by:
-
Jeremy Cline authored
commit 889ad63d upstream. "qxl_bo_unref" may sleep, but calling "qxl_release_map" causes "preempt_disable()" to be called and "preempt_enable()" isn't called until "qxl_release_unmap" is used. Move the call to "qxl_bo_unref" out from in between the two to avoid sleeping from an atomic context. This issue can be demonstrated on a kernel with CONFIG_LOCKDEP=y by creating a VM using QXL, using a desktop environment using Xorg, then moving the cursor on or off a window. Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1571128 Fixes: 9428088c ("drm/qxl: reapply cursor after resetting primary") Cc: stable@vger.kernel.org Signed-off-by:
Jeremy Cline <jcline@redhat.com> Link: http://patchwork.freedesktop.org/patch/msgid/20180601200532.13619-1-jcline@redhat.comSigned-off-by:
Gerd Hoffmann <kraxel@redhat.com> Signed-off-by:
-
Huang Rui authored
commit a0b2ac29 upstream. It missed vcn.fw_version setting when init vcn microcode, and it will be used to report vcn ucode version via amdgpu_firmware_info sysfs interface. Signed-off-by:
Huang Rui <ray.huang@amd.com> Reviewed-by:
-
Rex Zhu authored
commit 08ebb6e9 upstream. 1. fix set vce clocks failed on Cz/St which lead 1s delay when boot up. 2. remove the workaround in vce_v3_0.c Reviewed-by:
Shirish S <shirish.s@amd.com> Signed-off-by:
Rex Zhu <Rex.Zhu@amd.com> Signed-off-by:
-
Rex Zhu authored
commit 819a23f8 upstream. fix the issue set uvd clock failed on CZ/ST which lead 1s delay when boot up. Reviewed-by:
-
Alexander Potapenko authored
commit 21eff69a upstream. KMSAN reported an infoleak when reading from /dev/vcs*: BUG: KMSAN: kernel-infoleak in vcs_read+0x18ba/0x1cc0 Call Trace: ... kmsan_copy_to_user+0x7a/0x160 mm/kmsan/kmsan.c:1253 copy_to_user ./include/linux/uaccess.h:184 vcs_read+0x18ba/0x1cc0 drivers/tty/vt/vc_screen.c:352 __vfs_read+0x1b2/0x9d0 fs/read_write.c:416 vfs_read+0x36c/0x6b0 fs/read_write.c:452 ... Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:279 kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:189 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:315 __kmalloc+0x13a/0x350 mm/slub.c:3818 kmalloc ./include/linux/slab.h:517 vc_allocate+0x438/0x800 drivers/tty/vt/vt.c:787 con_install+0x8c/0x640 drivers/tty/vt/vt.c:2880 tty_driver_install_tty drivers/tty/tty_io.c:1224 tty_init_dev+0x1b5/0x1020 drivers/tty/tty_io.c:1324 tty_open_by_driver drivers/tty/tty_io.c:1959 tty_open+0x17b4/0x2ed0 drivers/tty/tty_io.c:2007 chrdev_open+0xc25/0xd90 fs/char_dev.c:417 do_dentry_open+0xccc/0x1440 fs/open.c:794 vfs_open+0x1b6/0x2f0 fs/open.c:908 ... Bytes 0-79 of 240 are uninitialized Consistently allocating |vc_screenbuf| with kzalloc() fixes the problem Reported-by: syzbot+17a8efdf800000@syzkaller.appspotmail.com Signed-off-by:
Alexander Potapenko <glider@google.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
commit bc6cf366 upstream. Make sure to free all resources associated with the ida on module exit. Fixes: cd6484e1 ("serdev: Introduce new bus for serial attached devices") Cc: stable <stable@vger.kernel.org> # 4.11 Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Andy Shevchenko authored
commit 20dcff43 upstream. After the commit 7d8905d0 ("serial: 8250_pci: Enable device after we check black list") pure serial multi-port cards, such as CH355, got blacklisted and thus not being enumerated anymore. Previously, it seems, blacklisting them was on purpose to shut up pciserial_init_one() about record duplication. So, remove the entries from blacklist in order to get cards enumerated. Fixes: 7d8905d0 ("serial: 8250_pci: Enable device after we check black list") Reported-by:
Matt Turner <mattst88@gmail.com> Cc: Sergej Pupykin <ml@sergej.pp.ru> Cc: Alexandr Petrenko <petrenkoas83@gmail.com> Signed-off-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Reviewed-and-Tested-by:
-
Laura Abbott authored
commit 0a2bc003 upstream. The expected return value from ion_map_kernel is an ERR_PTR. The error path for a vmalloc failure currently just returns NULL, triggering a warning in ion_buffer_kmap_get. Encode the vmalloc failure as an ERR_PTR. Reported-by: syzbot+55b1d9f811650de944c6@syzkaller.appspotmail.com Signed-off-by:
Laura Abbott <labbott@redhat.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Tetsuo Handa authored
commit ebec3f8f upstream. syzbot is reporting stalls at __process_echoes() [1]. This is because since ldata->echo_commit < ldata->echo_tail becomes true for some reason, the discard loop is serving as almost infinite loop. This patch tries to avoid falling into ldata->echo_commit < ldata->echo_tail situation by making access to echo_* variables more carefully. Since reset_buffer_flags() is called without output_lock held, it should not touch echo_* variables. And omit a call to reset_buffer_flags() from n_tty_open() by using vzalloc(). Since add_echo_byte() is called without output_lock held, it needs memory barrier between storing into echo_buf[] and incrementing echo_head counter. echo_buf() needs corresponding memory barrier before reading echo_buf[]. Lack of handling the possibility of not-yet-stored multi-byte operation might be the reason of falling into ldata->echo_commit < ldata->echo_tail situation, for if I do WARN_ON(ldata->echo_commit == tail + 1) prior to echo_buf(ldata, tail + 1), the WARN_ON() fires. Also, explicitly masking with buffer for the former "while" loop, and use ldata->echo_commit > tail for the latter "while" loop. [1] https://syzkaller.appspot.com/bug?id=17f23b094cd80df750e5b0f8982c521ee6bcbf40Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Reported-by:
syzbot <syzbot+108696293d7a21ab688f@syzkaller.appspotmail.com> Cc: Peter Hurley <peter@hurleysoftware.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Tetsuo Handa authored
commit 3d63b7e4 upstream. syzbot is reporting stalls at n_tty_receive_char_special() [1]. This is because comparison is not working as expected since ldata->read_head can change at any moment. Mitigate this by explicitly masking with buffer size when checking condition for "while" loops. [1] https://syzkaller.appspot.com/bug?id=3d7481a346958d9469bebbeb0537d5f056bdd6e8Signed-off-by:
syzbot <syzbot+18df353d7540aa6b5467@syzkaller.appspotmail.com> Fixes: bc5a5e3f ("n_tty: Don't wrap input buffer indices at buffer size") Cc: stable <stable@vger.kernel.org> Cc: Peter Hurley <peter@hurleysoftware.com> Signed-off-by:
-
Zhengjun Xing authored
commit d850c165 upstream. commit 44a182b9 ("xhci: Fix use-after-free in xhci_free_virt_device") set dev->udev pointer to NULL in xhci_free_dev(), it will cause kernel panic in trace_xhci_free_virt_device. This patch reimplement the trace function trace_xhci_free_virt_device, remove dev->udev dereference and added more useful parameters to show in the trace function,it also makes sure dev->udev is not NULL before calling trace_xhci_free_virt_device. This issue happened when xhci-hcd trace is enabled and USB devices hot plug test. Original use-after-free patch went to stable so this needs so be applied there as well. [ 1092.022457] usb 2-4: USB disconnect, device number 6 [ 1092.092772] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000 [ 1092.101694] PGD 0 P4D 0 [ 1092.104601] Oops: 0000 [#1] SMP [ 1092.207734] Workqueue: usb_hub_wq hub_event [ 1092.212507] RIP: 0010:trace_event_raw_event_xhci_log_virt_dev+0x6c/0xf0 [ 1092.220050] RSP: 0018:ffff8c252e883d28 EFLAGS: 00010086 [ 1092.226024] RAX: ffff8c24af86fa84 RBX: 0000000000000003 RCX: ffff8c25255c2a01 [ 1092.234130] RDX: 0000000000000000 RSI: 00000000aef55009 RDI: ffff8c252e883d28 [ 1092.242242] RBP: ffff8c252550e2c0 R08: ffff8c24af86fa84 R09: 0000000000000a70 [ 1092.250364] R10: 0000000000000a70 R11: 0000000000000000 R12: ffff8c251f21a000 [ 1092.258468] R13: 000000000000000c R14: ffff8c251f21a000 R15: ffff8c251f432f60 [ 1092.266572] FS: 0000000000000000(0000) GS:ffff8c252e880000(0000) knlGS:0000000000000000 [ 1092.275757] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 1092.282281] CR2: 0000000000000000 CR3: 0000000154209001 CR4: 00000000003606e0 [ 1092.290384] Call Trace: [ 1092.293156] <IRQ> [ 1092.295439] xhci_free_virt_device.part.34+0x182/0x1a0 [ 1092.301288] handle_cmd_completion+0x7ac/0xfa0 [ 1092.306336] ? trace_event_raw_event_xhci_log_trb+0x6e/0xa0 [ 1092.312661] xhci_irq+0x3e8/0x1f60 [ 1092.316524] __handle_irq_event_percpu+0x75/0x180 [ 1092.321876] handle_irq_event_percpu+0x20/0x50 [ 1092.326922] handle_irq_event+0x36/0x60 [ 1092.331273] handle_edge_irq+0x6d/0x180 [ 1092.335644] handle_irq+0x16/0x20 [ 1092.339417] do_IRQ+0x41/0xc0 [ 1092.342782] common_interrupt+0xf/0xf [ 1092.346955] </IRQ> Fixes: 44a182b9 ("xhci: Fix use-after-free in xhci_free_virt_device") Cc: <stable@vger.kernel.org> Signed-off-by:
Zhengjun Xing <zhengjun.xing@linux.intel.com> Signed-off-by:
Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by:
-
Heikki Krogerus authored
commit 68816e16 upstream. According to UCSI Specification, Connector Change Event only means a change in the Connector Status and Operation Mode fields of the STATUS data structure. So any other change should create another event. Unfortunately on some platforms the firmware acting as PPM (platform policy manager - usually embedded controller firmware) still does not report any other status changes if there is a connector change event. So if the connector power or data role was changed when a device was plugged to the connector, the driver does not get any indication about that. The port will show wrong roles if that happens. To fix the issue, always checking the data and power role together with a connector change event. Fixes: c1b0bc2d ("usb: typec: Add support for UCSI interface") Signed-off-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Heikki Krogerus authored
commit 1f9f9d16 upstream. This fixes an issue where the driver fails with an error: ioremap error for 0x3f799000-0x3f79a000, requested 0x2, got 0x0 On some platforms the UCSI ACPI mailbox SystemMemory Operation Region may be setup before the driver has been loaded. That will lead into the driver failing to map the mailbox region, as it has been already marked as write-back memory. acpi_os_ioremap() for x86 uses ioremap_cache() unconditionally. When the issue happens, the embedded controller has a pending query event for the UCSI notification right after boot-up which causes the operation region to be setup before UCSI driver has been loaded. The fix is to notify acpi core that the driver is about to access memory region which potentially overlaps with an operation region right before mapping it. acpi_release_memory() will check if the memory has already been setup (mapped) by acpi core, and deactivate it (unmap) if it has. The driver is then able to map the memory with ioremap_nocache() and set the memtype to uncached for the region. Reported-by:
Paul Menzel <pmenzel@molgen.mpg.de> Fixes: 8243edf4 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Signed-off-by:
-
Heikki Krogerus authored
commit d2d2e3c4 upstream. Sometimes memory resource may be overlapping with SystemMemory Operation Region by design, for example if the memory region is used as a mailbox for communication with a firmware in the system. One occasion of such mailboxes is USB Type-C Connector System Software Interface (UCSI). With regions like that, it is important that the driver is able to map the memory with the requirements it has. For example, the driver should be allowed to map the memory as non-cached memory. However, if the operation region has been accessed before the driver has mapped the memory, the memory has been marked as write-back by the time the driver is loaded. That means the driver will fail to map the memory if it expects non-cached memory. To work around the problem, introducing helper that the drivers can use to temporarily deactivate (unmap) SystemMemory Operation Regions that overlap with their IO memory. Fixes: 8243edf4 ("usb: typec: ucsi: Add ACPI driver") Cc: stable@vger.kernel.org Reviewed-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
William Wu authored
commit 87606759 upstream. The dwc2_get_ls_map() use ttport to reference into the bitmap if we're on a multi_tt hub. But the bitmaps index from 0 to (hub->maxchild - 1), while the ttport index from 1 to hub->maxchild. This will cause invalid memory access when the number of ttport is hub->maxchild. Without this patch, I can easily meet a Kernel panic issue if connect a low-speed USB mouse with the max port of FE2.1 multi-tt hub (1a40:0201) on rk3288 platform. Fixes: 9f9f09b0 ("usb: dwc2: host: Totally redo the microframe scheduler") Cc: <stable@vger.kernel.org> Reviewed-by:
Douglas Anderson <dianders@chromium.org> Acked-by: Minas Harutyunyan hminas@synopsys.com> Signed-off-by:
William Wu <william.wu@rock-chips.com> Signed-off-by:
Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by:
-
Karoly Pados authored
commit 2f839823 upstream. Silicon Labs defines alternative VID/PID pairs for some chips that when used will automatically install drivers for Windows users without manual intervention. Unfortunately, these IDs are not recognized by the Linux module, so using these IDs improves user experience on one platform but degrades it on Linux. This patch addresses this problem. Signed-off-by:
Karoly Pados <pados@pados.hu> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Johan Hovold authored
commit 24160628 upstream. Add device ids for CESINEL products. Reported-by:
Carlos Barcala Lara <cabl@cesinel.com> Cc: stable <stable@vger.kernel.org> Signed-off-by:
-
Houston Yaroschoff authored
commit 4a762569 upstream. Uniden UBC125 radio scanner has USB interface which fails to work with cdc_acm driver: usb 1-1.5: new full-speed USB device number 4 using xhci_hcd cdc_acm 1-1.5:1.0: Zero length descriptor references cdc_acm: probe of 1-1.5:1.0 failed with error -22 Adding the NO_UNION_NORMAL quirk for the device fixes the issue: usb 1-4: new full-speed USB device number 15 using xhci_hcd usb 1-4: New USB device found, idVendor=1965, idProduct=0018 usb 1-4: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-4: Product: UBC125XLT usb 1-4: Manufacturer: Uniden Corp. usb 1-4: SerialNumber: 0001 cdc_acm 1-4:1.0: ttyACM0: USB ACM device `lsusb -v` of the device: Bus 001 Device 015: ID 1965:0018 Uniden Corporation Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 2.00 bDeviceClass 2 Communications bDeviceSubClass 0 bDeviceProtocol 0 bMaxPacketSize0 64 idVendor 0x1965 Uniden Corporation idProduct 0x0018 bcdDevice 0.01 iManufacturer 1 Uniden Corp. iProduct 2 UBC125XLT iSerial 3 0001 bNumConfigurations 1 Configuration Descriptor: bLength 9 bDescriptorType 2 wTotalLength 48 bNumInterfaces 2 bConfigurationValue 1 iConfiguration 0 bmAttributes 0x80 (Bus Powered) MaxPower 500mA Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 0 bAlternateSetting 0 bNumEndpoints 1 bInterfaceClass 2 Communications bInterfaceSubClass 2 Abstract (modem) bInterfaceProtocol 0 None iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x87 EP 7 IN bmAttributes 3 Transfer Type Interrupt Synch Type None Usage Type Data wMaxPacketSize 0x0008 1x 8 bytes bInterval 10 Interface Descriptor: bLength 9 bDescriptorType 4 bInterfaceNumber 1 bAlternateSetting 0 bNumEndpoints 2 bInterfaceClass 10 CDC Data bInterfaceSubClass 0 Unused bInterfaceProtocol 0 iInterface 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x81 EP 1 IN bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Endpoint Descriptor: bLength 7 bDescriptorType 5 bEndpointAddress 0x02 EP 2 OUT bmAttributes 2 Transfer Type Bulk Synch Type None Usage Type Data wMaxPacketSize 0x0040 1x 64 bytes bInterval 0 Device Status: 0x0000 (Bus Powered) Signed-off-by:
Houston Yaroschoff <hstn@4ever3.net> Cc: stable <stable@vger.kernel.org> Acked-by:
Oliver Neukum <oneukum@suse.com> Signed-off-by:
-
- 03 Jul, 2018 1 commit
-
-
Greg Kroah-Hartman authored
-
