- 19 Apr, 2022 26 commits
-
-
Bryan O'Donoghue authored
Adds a CAMSS definition block. Co-developed-by:
Julian Grahsl <jgrahsl@snap.com> Signed-off-by:
Bryan O'Donoghue <bryan.odonoghue@linaro.org> Signed-off-by:
Bjorn Andersson <bjorn.andersson@linaro.org> Link: https://lore.kernel.org/r/20220415164655.1679628-3-bryan.odonoghue@linaro.org
-
Bryan O'Donoghue authored
Add the camcc DT node for the Camera Clock Controller on sm8250. Signed-off-by:
-
Vinod Koul authored
Enable the i2c5, spi4, spi18 and spi19 nodes which were tested on qrd board along with related qup nodes and gpi_dma0 Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Vinod Koul authored
qupv3_id_1 was missing iommus property which cause any dma transaction to fail and board crash. So add the missing iommus. Fixes: 5188049c ("arm64: dts: qcom: Add base SM8450 DTSI") Signed-off-by:
-
Vinod Koul authored
qup2 has 7 SEs, so add the SEs (i2c and spi) along with pinconf for these SEs Signed-off-by:
-
Vinod Koul authored
qup1 has 7 SEs, I2C13 and I2C14 were already added so added the remaining SEs (i2c and spi) along with pinconf for these SEs Also add interconnect properties for I2C13 and I2C14 Signed-off-by:
-
Vinod Koul authored
qup0 has 7 SEs, with SE7 as uart and already added, so add the remaining 6 SEs (i2c and spi) along with pinconf for these SEs Signed-off-by:
-
Vinod Koul authored
qupv3_id_0 was missing iommus property which cause any dma transaction to fail and board crash. So add the missing iommus. While at it also add interconnect nodes for qup Fixes: 5188049c ("arm64: dts: qcom: Add base SM8450 DTSI") Signed-off-by:
-
Vinod Koul authored
GPI DMA can be used for DMA operations for QUP devices, so add the three gpi_dma insances found in this SoC Signed-off-by:
-
Bjorn Andersson authored
Some versions of the firmware for the SM8350 Hardware Development Kit (HDK) has FIFO mode disabled for i2c13 and must thus use GPI DMA. Enable &gpi_dma1 to allow this. Signed-off-by:
-
Bjorn Andersson authored
The GENI I2C and SPI controllers may use the GPI DMA engine, define the rx and tx channels for these controllers to enable this. Signed-off-by:
-
Bjorn Andersson authored
The Qualcomm SM8350 has three GPI DMA engines, add definitions for these. Signed-off-by:
-
Sandeep Maheswaram authored
Adding wakeup-source property for USB controller in SC7280. This property is added to inform that the USB controller is wake up capable and to conditionally power down the phy during system suspend. Signed-off-by:
Sandeep Maheswaram <quic_c_sanm@quicinc.com> Reviewed-by:
Matthias Kaehlcke <mka@chromium.org> Signed-off-by:
-
Krzysztof Kozlowski authored
Using node paths to extend or override a device tree node is error prone. If there was a typo error, a new node will be created instead of extending the existing node. This will lead to run-time errors that could be hard to detect. A mistyped label on the other hand, will cause a dtc compile error (during build time). This also reduces the indentation making the code easier to read. Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Signed-off-by:
-
Krzysztof Kozlowski authored
Using node paths to extend or override a device tree node is error prone. If there was a typo error, a new node will be created instead of extending the existing node. This will lead to run-time errors that could be hard to detect. A mistyped label on the other hand, will cause a dtc compile error (during build time). This also reduces the indentation making the code easier to read. Signed-off-by:
-
Joel Selvaraj authored
Xiaomi Poco F1 uses the QCOM WLED driver for backlight control. Enable and link it to the panel to use it. Signed-off-by:
Joel Selvaraj <jo@jsfamily.in> Reviewed-by:
Marijn Suijten <marijn.suijten@somainline.org> Signed-off-by:
-
Joel Selvaraj authored
Like the c630, the Poco F1 is also capable of using both antenna channels for 2.4 and 5ghz wifi, however unlike the c630 only the first channel is used for bluetooth. Similar to Oneplus 6. Signed-off-by:
Caleb Connolly <caleb@connolly.tech> Signed-off-by:
-
Joel Selvaraj authored
vddio is misspelled with a "0" instead of "o". Fix it. Signed-off-by:
-
Joel Selvaraj authored
Enable Qualcomm IP Accelerator (IPA) driver for mobile data functionality which works by using ModemManager. Signed-off-by:
-
Joel Selvaraj authored
The "qcom/sdm845/" path conflicts with db845c's firmware that are present in the linux-firmware package. Xiaomi uses their own signed firmware for Poco F1 and can't use the db845c's firmware. So let's use "qcom/sdm845/beryllium/" to distinguish Poco F1's firmware files. For easier handling and packaging, the mdt+bXX files are squashed using Bjorn Andersson's pil-squasher tool from this link: https://github.com/andersson/pil-squasherSigned-off-by:
-
Krzysztof Kozlowski authored
Align BCM voter node with DT schema by using hyphen instead of underscore. Signed-off-by:
-
Vladimir Zapolskiy authored
Add thermal zones handled by tsens sensors. The definitions and the trip points were taken from the downstream dts. For the CPU core thermal sensors, the trip points were changed to follow the example of other Qualcomm platforms. Signed-off-by:
Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org> Signed-off-by:
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> Signed-off-by:
-
Vladimir Zapolskiy authored
The change adds description of two thermal sensor controllers found on SM8450. Signed-off-by:
-
Michael Srba authored
With the gcc driver now being more complete and describing clocks which might not always be write-accessible to the OS, conservatively specify all such clocks as protected in the SoC dts. The board dts - or even user-supplied dts - can override this property to reflect the actual configuration. Signed-off-by:
Michael Srba <michael.srba@seznam.cz> Reviewed-by:
Jeffrey Hugo <jeffrey.l.hugo@gmail.com> Signed-off-by:
-
Bjorn Andersson authored
-
Michael Srba authored
Add definitions of four clocks which need to be manipulated in order to initialize the AHB bus which exposes the SCC block in the global address space. Signed-off-by:
Rob Herring <robh@kernel.org> Reviewed-by:
Stephen Boyd <sboyd@kernel.org> Signed-off-by:
-
- 13 Apr, 2022 14 commits
-
-
Krzysztof Kozlowski authored
The bindings require a fallback compatible to RPM clock controller. Signed-off-by:
-
Krzysztof Kozlowski authored
The Qualcomm SMD does not use qcom,local-pid property. Signed-off-by:
-
Krzysztof Kozlowski authored
Align RPM requests node with DT schema by using hyphen instead of underscore. Signed-off-by:
-
Luca Weiss authored
Configure regulators used by the wifi hardware and enable it. Signed-off-by:
Luca Weiss <luca.weiss@fairphone.com> Signed-off-by:
-
Luca Weiss authored
Add a node describing the wifi hardware found on sm6350. Signed-off-by:
-
Konrad Dybcio authored
Set the aliases for both SDHCI controllers. Signed-off-by:
Konrad Dybcio <konrad.dybcio@somainline.org> Reviewed-by:
Petr Vorel <petr.vorel@gmail.com> Signed-off-by:
-
Konrad Dybcio authored
Add and configure the watchdog node. Signed-off-by:
-
Konrad Dybcio authored
MSM8994 actually features 24 DMA channels for each BLSP, fix it! Signed-off-by:
-
Konrad Dybcio authored
Add OCMEM node to allow for GPU SRAM access. Signed-off-by:
-
Konrad Dybcio authored
Remove regulator-always-on property where not necessary and mark regulators that are not supposed to be voted active on boot with regulator-boot-on. While at it, reorder the load properties to make it look more decent. Reorder PMICs to fix a probe defer caused by messy dependencies and Linux's inability to handle them (at least for now). Signed-off-by:
-
Konrad Dybcio authored
I2C4 turns out not to be used on Kitakami after all and it only blocks a GPIO used by camera hardware. Signed-off-by:
-
Konrad Dybcio authored
Make sure the necessary clocks are kept on after clk_cleanup (until MDSS is properly handled by its own driver) and touch up the fb address to prevent some weird shifting. It's still not perfect, but at least the kernel log doesn't start a third deep into your screen.. Signed-off-by:
-
Konrad Dybcio authored
The default memory map places cont_splash_mem at 3401000, which was overlooked.. Fix it! Signed-off-by:
-
Konrad Dybcio authored
Now that proper msm8992 support is in the driver, switch to the new compatible. Signed-off-by:
-
