We only request the control interface error IRQ if we set ctrlif_error,
as such we should only free it in that situation. Otherwise we will
attempt to free an IRQ we never requested and get a warning from the IRQ
core.

This patch moves the ctrlif_error variable into the arizona structure
and checks it in all cases we free the control interface error IRQ.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Some parts have a third ISRC, this patch adds handling for the under and
overclocked interrupts from this ISRC.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Newer versions of the IP have a lot of new interrupts and move several
existing interrupts. This patch adds the register definitions and regmap
hookup for these interrupts.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Newer versions of the IP introduce short circuit protection which will
also shutdown the speaker. Rename the interrupt and associated register
bits associated with thermal events to better fit the function and avoid
conflict with future interrupt additions.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

wm5110 has interrupts to signal that an output has fully enabled. This
patch adds in these interrupts although use is not made of them yet.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The DCS_DAC_DONE and DCS_HP_DONE interrupts do not exist on the wm5110
version of the IP. This patch removes them from the regmap IRQ
structure.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

‘rx_buf’ is not used in this function.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Removed code unused in this function.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add register definitions for DA9063 AD (0x3) silicon variant ID
the ability to choose the silicon variant at run-time using regmap
configuration. This patch also adds RTC support for the AD silicon
changes.

It adds both BB and AD support as regmap ranges and then makes the
distinction between the two tables at run-time. This allows both AD
and BB silicon variants to be supported at the same time.
Suggested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Opensource [Steve Twiss] <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The extcon driver should be able to get its regulator against rather
than against the main arizona device, we must add a supply mapping
allowing the regulator to be located. This patch does so.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The previous update adding MICVDD to the regulator mappings:

mfd: arizona: Add MICVDD to mapped regulators

Only added the mapping for wm5102 and wm5110 but wm8997 also has a
MICVDD supply that needs to be mapped back to the main Arizona device.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Extinguishes:

../drivers/mfd/max77686.c: In function ‘max77686_i2c_probe’:
../drivers/mfd/max77686.c:254:20:
	warning: cast from pointer to integer of different size
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Maxim MAX77802 is a power management chip that contains 10 high
efficiency Buck regulators, 32 Low-dropout (LDO) regulators used
to power up application processors and peripherals, a 2-channel
32kHz clock outputs, a Real-Time-Clock (RTC) and a I2C interface
to program the individual regulators, clocks outputs and the RTC.

This patch adds support for MAX77802 to the MAX77686 driver and is
based on a driver added to the Chrome OS kernel 3.8 by Simon Glass.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch introduces the use of devm_kzalloc instead of the
corresponding unmanaged version and does away with the kfrees in the
probe and remove functions. Also, a label is done away with.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: line over 80 characters
+       { 0x00000068, 0x01FF },    /* R104   - Always On Triggers Sequence Select 3 */

WARNING: line over 80 characters
+       { 0x00000069, 0x01FF },    /* R105   - Always On Triggers Sequence Select 4 */

WARNING: line over 80 characters
+       { 0x0000006A, 0x01FF },    /* R106   - Always On Triggers Sequence Select 5 */

WARNING: line over 80 characters
+       { 0x0000006B, 0x01FF },    /* R107   - Always On Triggers Sequence Select 6 */
Signed-off-by: Lee Jones <lee.jones@linaro.org>

WARNING: line over 80 characters
+module_param_string(force_device_id, force_device_id, sizeof(force_device_id), 0);

WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.txt
+               msleep(1);

WARNING: __initdata should be placed after kempld_dmi_table[]
+static struct dmi_system_id __initdata kempld_dmi_table[] = {

WARNING: line over 80 characters
+               for (id = kempld_dmi_table; id->matches[0].slot != DMI_NONE; id++)

total: 0 errors, 4 warnings, 771 lines checked

This is part of an effort to clean-up the MFD subsystem.
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

ERROR: space required before the open parenthesis '('
+                       if(!micro->msg)

WARNING: unnecessary whitespace before a quoted newline
+                       dev_dbg(micro->dev, "key message ignored, no handle \n");

WARNING: unnecessary whitespace before a quoted newline
+                       dev_dbg(micro->dev, "touchscreen message ignored, no handle \n");

WARNING: space prohibited before semicolon
+               rx->id = (ch & 0xf0) >> 4 ;

total: 1 errors, 3 warnings, 482 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: line over 80 characters
+                        struct si476x_rsq_status_args *rsqargs,

WARNING: line over 80 characters
+                        struct si476x_rsq_status_report *report)

WARNING: Unnecessary space before function pointer arguments
+       int (*power_up) (struct si476x_core *,

WARNING: Unnecessary space before function pointer arguments
+       int (*power_down) (struct si476x_core *,

total: 0 errors, 4 warnings, 1555 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: braces {} are not necessary for single statement blocks
+       if (!iomem) {
+               return -EINVAL;
+       }

WARNING: sizeof *tc6387xb should be sizeof(*tc6387xb)
+       tc6387xb = kzalloc(sizeof *tc6387xb, GFP_KERNEL);

WARNING: Prefer [subsystem eg: netdev]_info([subsystem]dev, ... then dev_info(dev, ... then pr_info(...  to printk(KERN_INFO ...
+       printk(KERN_INFO "Toshiba tc6387xb initialised\n");

total: 0 errors, 3 warnings, 242 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: please, no space before tabs
+^IRSV_INTR_OFFSET,  ^I/* Bit 12^IReserved^I^I*/$

WARNING: Missing a blank line after declarations
+       u8 unmask_value;
+       ret = twl_i2c_read_u8(TWL_MODULE_PIH, &unmask_value,

WARNING: Missing a blank line after declarations
+       u8 mask_value;
+       ret = twl_i2c_read_u8(TWL_MODULE_PIH, &mask_value,

total: 0 errors, 3 warnings, 484 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: please, no spaces at the start of a line
+       { "wm8350", 0 },$

WARNING: please, no spaces at the start of a line
+       { "wm8351", 0 },$

WARNING: please, no spaces at the start of a line
+       { "wm8352", 0 },$

WARNING: please, no spaces at the start of a line
+       { }$

total: 0 errors, 4 warnings, 93 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: Missing a blank line after declarations
+       struct max8925_chip *chip = irq_data_get_irq_chip_data(data);
+       max8925_irqs[data->irq - chip->irq_base].enable

WARNING: Missing a blank line after declarations
+       struct max8925_chip *chip = irq_data_get_irq_chip_data(data);
+       max8925_irqs[data->irq - chip->irq_base].enable = 0;

total: 0 errors, 2 warnings, 927 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: Prefer pr_warn(... to pr_warning(...
+               pr_warning("twl4030: I2C error %d reading PIH ISR\n", ret);

WARNING: sizeof buf should be sizeof(buf)
+       memset(buf, 0xff, sizeof buf);

WARNING: sizeof *agent should be sizeof(*agent)
+       agent = kzalloc(sizeof *agent, GFP_KERNEL);
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: Missing a blank line after declarations
+       struct lp8788_irq_data *irqd = irq_data_get_irq_chip_data(data);
+       irqd->enabled[data->hwirq] = 1;

WARNING: Missing a blank line after declarations
+       struct lp8788_irq_data *irqd = irq_data_get_irq_chip_data(data);
+       irqd->enabled[data->hwirq] = 0;

total: 0 errors, 2 warnings, 198 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: sizeof t should be sizeof(t)
+       memset(&t, 0, sizeof t);

WARNING: void function return statements are not generally useful
+       return;
+}

total: 0 errors, 2 warnings, 542 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

ERROR: space required after that ',' (ctx:VxO)
+                                 0, &twl6040_irq_chip,&twl6040->irq_data);
                                                      ^

ERROR: space required before that '&' (ctx:OxV)
+                                 0, &twl6040_irq_chip,&twl6040->irq_data);
                                                       ^

total: 2 errors, 0 warnings, 816 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: Missing a blank line after declarations
+               const struct of_device_id *match;
+               match = of_match_node(sec_dt_match, i2c->dev.of_node);

total: 0 errors, 1 warnings, 494 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

ERROR: space required after that ',' (ctx:VxV)
+#define MSP_GPIO(bit,reg)      ((DM355EVM_MSP_ ## reg) << 3 | (bit))
                     ^

total: 1 errors, 0 warnings, 437 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: line over 80 characters
+       wm8350->irq_base = irq_alloc_descs(irq_base, 0, ARRAY_SIZE(wm8350_irqs), 0);

total: 0 errors, 1 warnings, 552 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: Missing a blank line after declarations
+       unsigned long flags;
+       spin_lock_irqsave(&mcp->lock, flags);

total: 0 errors, 1 warnings, 238 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

WARNING: Missing a blank line after declarations
+       int ret;
+       ret = i2c_add_driver(&max8925_driver);

total: 0 errors, 1 warnings, 275 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This is part of an effort to clean-up the MFD subsystem.

+WARNING: line over 80 characters
+                                      &max77686_rtc_regmap_config);

total: 0 errors, 1 warnings, 299 lines checked
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There is no need to print out-of-memory errors since this is already
done by the memory management subsystem which even calls dump_stack().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Error checking across the driver is mostly consistent besides
a few exceptions, so change these exceptions for consistency.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When platform data is not found an -EIO (I/O error) code is returned.
This doesn't seem to be the correct error so better return -EINVAL
(Invalid argument) which is what most drivers do in this case.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The function max77802_i2c_parse_dt_pdata() should only be called
if there isn't already platform data for the device.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When the CONFIG_OF option was not enabled, a dummy function
max77686_i2c_parse_dt_pdata() was defined since this is called
unconditionally on probe(). Just always define the real function
and conditionally call it if CONFIG_OF is enabled instead.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The driver doesn't have PM operations defined so add a suspend
and resume function handlers to allow the PMIC IRQ to wakeup
the system when it is put into a sleep state.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

By using the generic IRQ support in the Register map API, it
is possible to get rid max77686-irq.c and simplify the code.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Allwinner A23 SoC has a PRCM unit like the previous A31 SoC.
The differences are the AR100 clock can no longer be modified,
the APB0 clock has different divisors, and some clock gates are
gone.

This patch adds a compatible with a modified subdevice list for
the A23.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>