- 05 Jun, 2012 19 commits
-
-
Arik Nemtsov authored
Implement the 18xx-specific way for getting the length of a Rx packet. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Implement the HW op for getting alignment state in wl18xx. The FW aligns the Rx Ethernet payload data. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
The 18xx FW sends Rx blocks with aligned length. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
The wl18xx chip passes extra information in the firmware status to the driver. Add a private data section to handle that. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Arik Nemtsov authored
Define HW-rate conversion tables for the 18xx chip. Initialize the appropriate wlcore elements with these tables and values to allow conversion of HW-rates. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Set the frame length during Tx in a way compatible with the 18xx FW. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Add the 18xx variant to the HW Tx descriptor union and set the 18xx specific values during Tx. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Implement the calc_tx_blocks op for the 18xx family. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Initialize the Tx spare block counts for all operating modes in the 18xx card. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Initialize the number of Tx-descriptors for the 18xx family. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Arik Nemtsov authored
Make use of the wlcore provided private storage in the 18xx low-level driver. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
-
Luciano Coelho authored
Add the operations that allow wlcore to trigger commands to the firmware and acknowledge when an event has been fully received. Allocate a private buffer to hold the maximum sized cmd. Send the entire length of the buffer each time a command is sent to signal EOT. Remove the previous EOT mechanism. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
Implement the boot operation. Add a wl18xx-specific configuration structure (namely to configure the mac and phy parameters). The default hw configuration matches the DVP board. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
Add identify_chip operation to detect the chip ID for wl185x and set the correct firmware name. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
Add the register table with the appropriate values for wl18xx. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
Define and add the partition table in the wlcore struct. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
We don't have any chip-specific operations yet, but now wlcore has defined an operations structure and requires the pointer to be set. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
At least in PG1, the wl18xx chips use the same SDIO vendor/device ID, so it's not possible to figure out which driver is to be used. As a workaround, we can check the SDIO revision number, because wl18xx uses 3.00 and wl12xx does not. Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
Luciano Coelho authored
Add the wl18xx module and the probe functions. Use wlcore for the main parts (not functional at this point due to differences in the wl18xx initialization). Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
-
- 03 Jun, 2012 2 commits
-
-
Linus Torvalds authored
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dmLinus Torvalds authored
Pull device-mapper updates from Alasdair G Kergon: "Improve multipath's retrying mechanism in some defined circumstances and provide a simple reserve/release mechanism for userspace tools to access thin provisioning metadata while the pool is in use." * tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: dm thin: provide userspace access to pool metadata dm thin: use slab mempools dm mpath: allow ioctls to trigger pg init dm mpath: delay retry of bypassed pg dm mpath: reduce size of struct multipath
-
- 02 Jun, 2012 18 commits
-
-
Joe Thornber authored
This patch implements two new messages that can be sent to the thin pool target allowing it to take a snapshot of the _metadata_. This, read-only snapshot can be accessed by userland, concurrently with the live target. Only one metadata snapshot can be held at a time. The pool's status line will give the block location for the current msnap. Since version 0.1.5 of the userland thin provisioning tools, the thin_dump program displays the msnap as follows: thin_dump -m <msnap root> <metadata dev> Available here: https://github.com/jthornber/thin-provisioning-tools Now that userland can access the metadata we can do various things that have traditionally been kernel side tasks: i) Incremental backups. By using metadata snapshots we can work out what blocks have changed over time. Combined with data snapshots we can ensure the data doesn't change while we back it up. A short proof of concept script can be found here: https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb ii) Migration of thin devices from one pool to another. iii) Merging snapshots back into an external origin. iv) Asyncronous replication. Signed-off-by: Joe Thornber <ejt@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
-
Mike Snitzer authored
Use dedicated caches prefixed with a "dm_" name rather than relying on kmalloc mempools backed by generic slab caches so the memory usage of thin provisioning (and any leaks) can be accounted for independently. Signed-off-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
-
Mikulas Patocka authored
After the failure of a group of paths, any alternative paths that need initialising do not become available until further I/O is sent to the device. Until this has happened, ioctls return -EAGAIN. With this patch, new paths are made available in response to an ioctl too. The processing of the ioctl gets delayed until this has happened. Instead of returning an error, we submit a work item to kmultipathd (that will potentially activate the new path) and retry in ten milliseconds. Note that the patch doesn't retry an ioctl if the ioctl itself fails due to a path failure. Such retries should be handled intelligently by the code that generated the ioctl in the first place, noting that some SCSI commands should not be retried because they are not idempotent (XOR write commands). For commands that could be retried, there is a danger that if the device rejected the SCSI command, the path could be errorneously marked as failed, and the request would be retried on another path which might fail too. It can be determined if the failure happens on the device or on the SCSI controller, but there is no guarantee that all SCSI drivers set these flags correctly. Signed-off-by: Mikulas Patocka <mpatocka@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
-
Mike Christie authored
If I/O needs retrying and only bypassed priority groups are available, set the pg_init_delay_retry flag to wait before retrying. If, for example, the reason for the bypass is that the controller is getting reset or there is a firmware upgrade happening, retrying right away would cause a flood of log messages and retries for what could be a few seconds or even several minutes. Signed-off-by: Mike Christie <michaelc@cs.wisc.edu> Acked-by: Mike Snitzer <snitzer@redhat.com> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
-
Mike Snitzer authored
Move multipath structure's 'lock' and 'queue_size' members to eliminate two 4-byte holes. Also use a bit within a single unsigned int for each existing flag (saves 8-bytes). This allows future flags to be added without each consuming an unsigned int. Signed-off-by: Mike Snitzer <snitzer@redhat.com> Acked-by: Hannes Reinecke <hare@suse.de> Signed-off-by: Alasdair G Kergon <agk@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds authored
Pull networking updates from David Miller: 1) Make syn floods consume significantly less resources by a) Not pre-COW'ing routing metrics for SYN/ACKs b) Mirroring the device queue mapping of the SYN for the SYN/ACK reply. Both from Eric Dumazet. 2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA. 3) Validate the length requested when building a paged SKB for a socket, so we don't overrun the page vector accidently. From Jason Wang. 4) When netlabel is disabled, we abort all IP option processing when we see a CIPSO option. This isn't the right thing to do, we should simply skip over it and continue processing the remaining options (if any). Fix from Paul Moore. 5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel Apfelbaum. 6) 8139cp enables the receiver before the ring address is properly programmed, which potentially lets the device crap over random memory. Fix from Jason Wang. 7) e1000/e1000e fixes for i217 RST handling, and an improper buffer address reference in jumbo RX frame processing from Bruce Allan and Sebastian Andrzej Siewior, respectively. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: fec_mpc52xx: fix timestamp filtering mcs7830: Implement link state detection e1000e: fix Rapid Start Technology support for i217 e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats() r8169: call netif_napi_del at errpaths and at driver unload tcp: reflect SYN queue_mapping into SYNACK packets tcp: do not create inetpeer on SYNACK message 8139cp/8139too: terminate the eeprom access with the right opmode 8139cp: set ring address before enabling receiver cipso: handle CIPSO options correctly when NetLabel is disabled net: sock: validate data_len before allocating skb in sock_alloc_send_pskb() bql: Avoid possible inconsistent calculation. bql: Avoid unneeded limit decrement. bql: Fix POSDIFF() to integer overflow aware. net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap net/mlx4_core: Fixes for VF / Guest startup flow net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event net/mlx4_core: Fix number of EQs used in ICM initialisation net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull straggler x86 fixes from Peter Anvin: "Three groups of patches: - EFI boot stub documentation and the ability to print error messages; - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which should never have been ported, and the port is broken and potentially dangerous.) - ftrace stack corruption fixes. I'm not super-happy about the technical implementation, but it is probably the least invasive in the short term. In the future I would like a single method for nesting the debug stack, however." * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32 x86, efi: Add EFI boot stub documentation x86, efi; Add EFI boot stub console support x86, efi: Only close open files in error path ftrace/x86: Do not change stacks in DEBUG when calling lockdep x86: Allow nesting of the debug stack IDT setting x86: Reset the debug_stack update counter ftrace: Use breakpoint method to update ftrace caller ftrace: Synchronize variable setting with breakpoints
-
Linus Torvalds authored
This reverts the tty layer change to use per-tty locking, because it's not correct yet, and fixing it will require some more deep surgery. The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but there are several smaller commits that built upon it, they also get reverted here. The list of reverted commits is: fde86d31 - tty: add lockdep annotations 8f6576ad - tty: fix ldisc lock inversion trace d3ca8b64 - pty: Fix lock inversion b1d679af - tty: drop the pty lock during hangup abcefe5f - tty/amiserial: Add missing argument for tty_unlock() fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call d29f3ef3 - tty_lock: Localise the lock The revert had a trivial conflict in the 68360serial.c staging driver that got removed in the meantime. Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Stephan Gatzka authored
skb_defer_rx_timestamp was called with a freshly allocated skb but must be called with rskb instead. Signed-off-by: Stephan Gatzka <stephan@gatzka.org> Cc: stable <stable@vger.kernel.org> Acked-by: Richard Cochran <richardcochran@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
-
Ondrej Zary authored
Add .status callback that detects link state changes. Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver). Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: David S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/{vfs,signal}Linus Torvalds authored
Pull vfs fix and a fix from the signal changes for frv from Al Viro. The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc actually depended on the default "unsigned long", while 32-bit powerpc had an explicit override to "unsigned short". Al didn't notice, and made both of them be the unsigned short. The frv signal fix is fallout from simplifying the do_notify_resume() code, and leaving an extra parenthesis. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: powerpc: Fix size of st_nlink on 64bit * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: frv: Remove bogus closing parenthesis
-
Anton Blanchard authored
commit e57f93cc (powerpc: get rid of nlink_t uses, switch to explicitly-sized type) changed the size of st_nlink on ppc64 from a long to a short, resulting in boot failures. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Geert Uytterhoeven authored
Introduced by commit 6fd84c08 ("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set") Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
-
Bruce Allan authored
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY register greater than the maximum allowed by the latter macro, and fix a typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan. Also for clarity, rename a few defines as bit definitions instead of masks. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Sebastian Andrzej Siewior authored
This is another fixup where the data is not transfered into buffer addressed by skb->data but into a page. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Linus Torvalds authored
Merge fixups for the mac NLS tables from Andrew. * emailed from Andrew Morton, and one cleanup by me: nls: fix (and rename) mac NLS table files and config options fs/nls/Makefile: remove bogus CONFIG_ assignments
-
Linus Torvalds authored
The config options in the Kconfig file (with _CODEPAGE_ in the name) didn't match the config option name in the Makefile (no _CODEPAGE_). And both of them were of the hard-to-read MACXYZZY variety, which made them hard to parse for normal humans: MACROMAN easily reads as "macro man", not as "Mac Roman". So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's already in the directory name). Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
Andrew Morton authored
These were debug things which snuck through. Reported-by: Yinghai Lu <yinghai@kernel.org> Cc: Vladimir Serbinenko <phcoder@gmail.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
- 01 Jun, 2012 1 commit
-
-
git://github.com/schandinat/linux-2.6Linus Torvalds authored
Pull fbdev updates from Florian Tobias Schandinat: - driver for AUO-K1900 and AUO-K1901 epaper controller - large updates for OMAP (e.g. decouple HDMI audio and video) - some updates for Exynos and SH Mobile - various other small fixes and cleanups * tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits) video: bfin_adv7393fb: Fix cleanup code video: exynos_dp: reduce delay time when configuring video setting video: exynos_dp: move sw reset prioir to enabling sw defined function video: exynos_dp: use devm_ functions fb: handle NULL pointers in framebuffer release OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request OMAPDSS: Apply VENC timings even if panel is disabled OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC OMAPDSS: DISPC: Support rotation through TILER OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n OMAPFB: remove compiler warnings when CONFIG_BUG=n OMAPDSS: remove compiler warnings when CONFIG_BUG=n OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods OMAPDSS: DISPC: Update Accumulator configuration for chroma plane drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers video: exynos mipi dsi: support reverse panel type video: exynos mipi dsi: Properly interpret the interrupt source flags video: exynos mipi dsi: Avoid races in probe() ...
-