- 26 Aug, 2016 10 commits
-
-
Stefan Müller-Klieser authored
The wega board has a TLV320AIC3007 connected via McASP0. In the default configuration, no external crystal is mounted. We run a system clock of 25 MHz, so we use the audio codec PLL for audio clock generation. Signed-off-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de> Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Vignesh R authored
AM572x IDK has a Spansion s25fl256s1 QSPI flash on the EVM connected to TI QSPI IP over CS0. Hence, add QSPI and flash slave DT nodes. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Vignesh R authored
According to AM572x DM SPRS953A, QSPI maximum bus speed can be 76.8MHz. Therefore, increase the spi-max-frequency value of QSPI node to 76.8MHz for DRA74 and DRA72 evm. This improves flash raw read speed by ~2MB/s. Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Keerthy authored
With the device tree parsing using the regulator framework there is a no longer a need for separate compatibles for individual regulator nodes. Hence removing them all. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Keerthy authored
With the device tree parsing using the regulator framework there is a no longer a need for separate compatibles for individual regulator nodes. Hence removing them all. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Keerthy authored
With the device tree parsing using the regulator framework there is a no longer a need for separate compatibles for individual regulator nodes. Hence removing them all. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Keerthy authored
With the device tree parsing using the regulator framework there is a no longer a need for separate compatibles for individual regulator nodes. Hence removing them all. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tero Kristo authored
Without this, the memory will remain active during poweroff consuming extra power. Please note revision 2.1 PMIC seems to fail when DCDC3 disable is attempted, so this is not done on that PMIC revision. The PMIC revision checks in the regulator patches make sure of this. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Tero Kristo authored
Without this, the memory will remain active during poweroff consuming extra power. Signed-off-by: Tero Kristo <t-kristo@ti.com> Signed-off-by: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Keerthy authored
dcdc3, dcdc5, dcdc6 supply ddr and rtc respectively. These are required to be on during suspend. Hence set the state accordingly. Signed-off-by: Keerthy <j-keerthy@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 15 Aug, 2016 15 commits
-
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /leds/led@1 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /leds/led@1 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /gpio_keys/button0@10 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /gpio_keys/button0@10 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /fixedregulator@0 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /fixedregulator@0 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /fixedregulator@0 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /matrix_keypad@0 has a unit name, but no reg property" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
Commit b8d368ca ("ARM: dts: omap3: overo: remove unneded unit names in display nodes") removed the unit names for all Overo display nodes that didn't have a reg property. But the display in arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi does have a reg property so the correct fix was to make the unit name match the value of the reg property, instead of removing it. This patch fixes the following DTC warning for boards using this dtsi: "ocp/spi@48098000/display has a reg or ranges property, but no unit name" Fixes: b8d368ca ("ARM: dts: omap3: overo: remove unneded unit names in display nodes") Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Javier Martinez Canillas authored
This patch fixes the following DTC warnings for many boards: "Node /ocp has a reg or ranges property, but no unit name" Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
This fix was applied to a bunch of omap3 devices including LogicPD Torpedo, but this got missed since it was new around the same times the patches were applied. This makes the GPMC parameters match the Torpedo since they have the same processor PoP memory. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Adam Ford authored
This was applied to a variety of omap3 boards, so it should probably be applied here. I did not test NAND performance, but I tested this with UBI to confirm read/write didn't break. Signed-off-by: Adam Ford <aford173@gmail.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Johan Hovold authored
The gpmc ranges property for NAND at CS0 was being overridden by later includes that defined gpmc ethernet nodes, effectively breaking NAND on these systems: omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has malformed 'reg' property Instead of redefining the NAND range in every such dtsi, define all currently used ranges in omap3-overo-base.dtsi. Fixes: 98ce6007 ("ARM: dts: overo: Support PoP NAND") Cc: stable <stable@vger.kernel.org> # 4.3 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Johan Hovold authored
The gpmc ranges property for NAND at CS0 has been broken since it was first added. This currently prevents the nand gpmc child node from being probed: omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has malformed 'reg' property and consequently the NAND device from being registered. Fixes: 98ce6007 ("ARM: dts: overo: Support PoP NAND") Cc: stable <stable@vger.kernel.org> # 4.3 Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
Teresa Remmet authored
The check for the "elm_id" binding had been removed. This causes nand boot to fail on boards still using the old binding. Update the bindings on those boards. Signed-off-by: Teresa Remmet <t.remmet@phytec.de> Acked-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
-
- 08 Aug, 2016 1 commit
-
-
Linus Torvalds authored
-
- 07 Aug, 2016 10 commits
-
-
git://git.kernel.dk/linux-blockLinus Torvalds authored
Pull more block fixes from Jens Axboe: "As mentioned in the pull the other day, a few more fixes for this round, all related to the bio op changes in this series. Two fixes, and then a cleanup, renaming bio->bi_rw to bio->bi_opf. I wanted to do that change right after or right before -rc1, so that risk of conflict was reduced. I just rebased the series on top of current master, and no new ->bi_rw usage has snuck in" * 'for-linus' of git://git.kernel.dk/linux-block: block: rename bio bi_rw to bi_opf target: iblock_execute_sync_cache() should use bio_set_op_attrs() mm: make __swap_writepage() use bio_set_op_attrs() block/mm: make bdev_ops->rw_page() take a bool for read/write
-
git://people.freedesktop.org/~airlied/linuxLinus Torvalds authored
Pull drm zpos property support from Dave Airlie: "This tree was waiting on some media stuff I hadn't had time to get a stable branchpoint off, so I just waited until it was all in your tree first. It's been around a bit on the list and shouldn't affect anything outside adding the generic API and moving some ARM drivers to using it" * tag 'drm-for-v4.8-zpos' of git://people.freedesktop.org/~airlied/linux: drm: rcar: use generic code for managing zpos plane property drm/exynos: use generic code for managing zpos plane property drm: sti: use generic zpos for plane drm: add generic zpos property
-
Jens Axboe authored
Since commit 63a4cc24, bio->bi_rw contains flags in the lower portion and the op code in the higher portions. This means that old code that relies on manually setting bi_rw is most likely going to be broken. Instead of letting that brokeness linger, rename the member, to force old and out-of-tree code to break at compile time instead of at runtime. No intended functional changes in this commit. Signed-off-by: Jens Axboe <axboe@fb.com>
-
Jens Axboe authored
The original commit missed this function, it needs to mark it a write flush. Cc: Mike Christie <mchristi@redhat.com> Fixes: e742fc32 ("target: use bio op accessors") Signed-off-by: Jens Axboe <axboe@fb.com>
-
Jens Axboe authored
Cleaner than manipulating bio->bi_rw flags directly. Signed-off-by: Jens Axboe <axboe@fb.com>
-
Jens Axboe authored
Commit abf54548 changed it from an 'rw' flags type to the newer ops based interface, but now we're effectively leaking some bdev internals to the rest of the kernel. Since we only care about whether it's a read or a write at that level, just pass in a bool 'is_write' parameter instead. Then we can also move op_is_write() and friends back under CONFIG_BLOCK protection. Reviewed-by: Mike Christie <mchristi@redhat.com> Signed-off-by: Jens Axboe <axboe@fb.com>
-
git://git.lwn.net/linuxLinus Torvalds authored
Pull documentation fixes from Jonathan Corbet: "Three fixes for the docs build, including removing an annoying warning on 'make help' if sphinx isn't present" * tag 'doc-4.8-fixes' of git://git.lwn.net/linux: DocBook: use DOCBOOKS="" to ignore DocBooks instead of IGNORE_DOCBOOKS=1 Documenation: update cgroup's document path Documentation/sphinx: do not warn about missing tools in 'make help'
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_miscLinus Torvalds authored
Pull binfmt_misc update from James Bottomley: "This update is to allow architecture emulation containers to function such that the emulation binary can be housed outside the container itself. The container and fs parts both have acks from relevant experts. To use the new feature you have to add an F option to your binfmt_misc configuration" From the docs: "The usual behaviour of binfmt_misc is to spawn the binary lazily when the misc format file is invoked. However, this doesn't work very well in the face of mount namespaces and changeroots, so the F mode opens the binary as soon as the emulation is installed and uses the opened image to spawn the emulator, meaning it is always available once installed, regardless of how the environment changes" * tag 'binfmt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/binfmt_misc: binfmt_misc: add F option description to documentation binfmt_misc: add persistent opened binary handler for containers fs: add filp_clone_open API
-
Eryu Guan authored
In most cases, EPERM is returned on immutable inode, and there're only a few places returning EACCES. I noticed this when running LTP on overlayfs, setxattr03 failed due to unexpected EACCES on immutable inode. So converting all EACCES to EPERM on immutable inode. Acked-by: Dave Chinner <dchinner@redhat.com> Signed-off-by: Eryu Guan <guaneryu@gmail.com> Signed-off-by: Al Viro <viro@zeniv.linux.org.uk> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull more vfs updates from Al Viro: "Assorted cleanups and fixes. In the "trivial API change" department - ->d_compare() losing 'parent' argument" * 'for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: cachefiles: Fix race between inactivating and culling a cache object 9p: use clone_fid() 9p: fix braino introduced in "9p: new helper - v9fs_parent_fid()" vfs: make dentry_needs_remove_privs() internal vfs: remove file_needs_remove_privs() vfs: fix deadlock in file_remove_privs() on overlayfs get rid of 'parent' argument of ->d_compare() cifs, msdos, vfat, hfs+: don't bother with parent in ->d_compare() affs ->d_compare(): don't bother with ->d_inode fold _d_rehash() and __d_rehash() together fold dentry_rcuwalk_invalidate() into its only remaining caller
-
- 06 Aug, 2016 4 commits
-
-
Linus Torvalds authored
Merge tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs Pull more xfs updates from Dave Chinner: "This is the second part of the XFS updates for this merge cycle, and contains the new reverse block mapping feature for XFS. Reverse mapping allows us to track the owner of a specific block on disk precisely. It is implemented as a set of btrees (one per allocation group) that track the owners of allocated extents. Effectively it is a "used space tree" that is updated when we allocate or free extents. i.e. it is coherent with the free space btrees we already maintain and never overlaps with them. This reverse mapping infrastructure is the building block of several upcoming features - reflink, copy-on-write data, dedupe, online metadata and data scrubbing, highly accurate bad sector/data loss reporting to users, and significantly improved reconstruction of damaged and corrupted filesystems. There's a lot of new stuff coming along in the next couple of cycles,a nd it all builds in the rmap infrastructure. As such, it's a huge chunk of new code with new on-disk format features and internal infrastructure. It warns at mount time as an experimental feature and that it may eat data (as we do with all new on-disk features until they stabilise). We have not released userspace suport for it yet - userspace support currently requires download from Darrick's xfsprogs repo and build from source, so the access to this feature is really developer/tester only at this point. Initial userspace support will be released at the same time kernel with this code in it is released. The new rmap enabled code regresses 3 xfstests - all are ENOSPC related corner cases, one of which Darrick posted a fix for a few hours ago. The other two are fixed by infrastructure that is part of the upcoming reflink patchset. This new ENOSPC infrastructure requires a on-disk format tweak required to keep mount times in check - we need to keep an on-disk count of allocated rmapbt blocks so we don't have to scan the entire btrees at mount time to count them. This is currently being tested and will be part of the fixes sent in the next week or two so users will not be exposed to this change" * tag 'xfs-rmap-for-linus-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs: (52 commits) xfs: move (and rename) the deferred bmap-free tracepoints xfs: collapse single use static functions xfs: remove unnecessary parentheses from log redo item recovery functions xfs: remove the extents array from the rmap update done log item xfs: in btree_lshift, only allocate temporary cursor when needed xfs: remove unnecesary lshift/rshift key initialization xfs: remove the get*keys and update_keys btree ops pointers xfs: enable the rmap btree functionality xfs: don't update rmapbt when fixing agfl xfs: disable XFS_IOC_SWAPEXT when rmap btree is enabled xfs: add rmap btree block detection to log recovery xfs: add rmap btree geometry feature flag xfs: propagate bmap updates to rmapbt xfs: enable the xfs_defer mechanism to process rmaps to update xfs: log rmap intent items xfs: create rmap update intent log items xfs: add rmap btree insert and delete helpers xfs: convert unwritten status of reverse mappings xfs: remove an extent from the rmap btree xfs: add an extent to the rmap btree ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfsLinus Torvalds authored
Pull qstr constification updates from Al Viro: "Fairly self-contained bunch - surprising lot of places passes struct qstr * as an argument when const struct qstr * would suffice; it complicates analysis for no good reason. I'd prefer to feed that separately from the assorted fixes (those are in #for-linus and with somewhat trickier topology)" * 'work.const-qstr' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: qstr: constify instances in adfs qstr: constify instances in lustre qstr: constify instances in f2fs qstr: constify instances in ext2 qstr: constify instances in vfat qstr: constify instances in procfs qstr: constify instances in fuse qstr constify instances in fs/dcache.c qstr: constify instances in nfs qstr: constify instances in ocfs2 qstr: constify instances in autofs4 qstr: constify instances in hfs qstr: constify instances in hfsplus qstr: constify instances in logfs qstr: constify dentry_init_security
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-mediaLinus Torvalds authored
Pull mailcap fixlets from Mauro Carvalho Chehab: "A small fixup for my and Shuah's entries in .mailcap. Basically, those entries were with a syntax that makes get_maintainer.pl to do the wrong thing" * tag 'media/v4.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: .mailmap: Correct entries for Mauro Carvalho Chehab and Shuah Khan
-
git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhostLinus Torvalds authored
Pull virtio/vhost updates from Michael Tsirkin: - new vsock device support in host and guest - platform IOMMU support in host and guest, including compatibility quirks for legacy systems. - misc fixes and cleanups. * tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: VSOCK: Use kvfree() vhost: split out vringh Kconfig vhost: detect 32 bit integer wrap around vhost: new device IOTLB API vhost: drop vringh dependency vhost: convert pre sorted vhost memory array to interval tree vhost: introduce vhost memory accessors VSOCK: Add Makefile and Kconfig VSOCK: Introduce vhost_vsock.ko VSOCK: Introduce virtio_transport.ko VSOCK: Introduce virtio_vsock_common.ko VSOCK: defer sock removal to transports VSOCK: transport-specific vsock_transport functions vhost: drop vringh dependency vop: pull in vhost Kconfig virtio: new feature to detect IOMMU device quirk balloon: check the number of available pages in leak balloon vhost: lockless enqueuing vhost: simplify work flushing
-