commit 9b55613f upstream.

When a kernel is built covering ARMv6 to ARMv7, we omit to clear the
IT state when entering a signal handler.  This can cause the first
few instructions to be conditionally executed depending on the parent
context.

In any case, the original test for >= ARMv7 is broken - ARMv6 can have
Thumb-2 support as well, and an ARMv6T2 specific build would omit this
code too.

Relax the test back to ARMv6 or greater.  This results in us always
clearing the IT state bits in the PSR, even on CPUs where these bits
are reserved.  However, they're reserved for the IT state, so this
should cause no harm.

Fixes: d71e1352 ("Clear the IT state when invoking a Thumb-2 signal handler")
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 6ecf830e upstream.

The ARM architecture reference specifies that the IT state bits in the
PSR must be all zeros in ARM mode or behavior is unspecified.  On the
Qualcomm Snapdragon S4/Krait architecture CPUs the processor continues
to consider the IT state bits while in ARM mode.  This makes it so
that some instructions are skipped by the CPU.
Signed-off-by: T.J. Purtell <tj@mobisocial.us>
[rmk+kernel@arm.linux.org.uk: fixed whitespace formatting in patch]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit caa47047 upstream.

The original patch introducing this header wrote the number of CPUs available
and online in one order and then swapped those values when reading, fix it.

Before:

  # perf record usleep 1
  # perf report --header-only | grep 'nrcpus \(online\|avail\)'
  # nrcpus online : 4
  # nrcpus avail : 4
  # echo 0 > /sys/devices/system/cpu/cpu2/online
  # perf record usleep 1
  # perf report --header-only | grep 'nrcpus \(online\|avail\)'
  # nrcpus online : 4
  # nrcpus avail : 3
  # echo 0 > /sys/devices/system/cpu/cpu1/online
  # perf record usleep 1
  # perf report --header-only | grep 'nrcpus \(online\|avail\)'
  # nrcpus online : 4
  # nrcpus avail : 2

After the fix, bringing back the CPUs online:

  # perf report --header-only | grep 'nrcpus \(online\|avail\)'
  # nrcpus online : 2
  # nrcpus avail : 4
  # echo 1 > /sys/devices/system/cpu/cpu2/online
  # perf record usleep 1
  # perf report --header-only | grep 'nrcpus \(online\|avail\)'
  # nrcpus online : 3
  # nrcpus avail : 4
  # echo 1 > /sys/devices/system/cpu/cpu1/online
  # perf record usleep 1
  # perf report --header-only | grep 'nrcpus \(online\|avail\)'
  # nrcpus online : 4
  # nrcpus avail : 4
Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Fixes: fbe96f29 ("perf tools: Make perf.data more self-descriptive (v8)")
Link: http://lkml.kernel.org/r/20150911153323.GP23511@kernel.orgSigned-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
[lizf: Backported to 3.4: fix it by saving values in an array and then print
 it in reverse order]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit e297c939 upstream.

This fixes a race which can result in the same virtual IRQ number
being assigned to two different MSI interrupts.  The most visible
consequence of that is usually a warning and stack trace from the
sysfs code about an attempt to create a duplicate entry in sysfs.

The race happens when one CPU (say CPU 0) is disposing of an MSI
while another CPU (say CPU 1) is setting up an MSI.  CPU 0 calls
(for example) pnv_teardown_msi_irqs(), which calls
msi_bitmap_free_hwirqs() to indicate that the MSI (i.e. its
hardware IRQ number) is no longer in use.  Then, before CPU 0 gets
to calling irq_dispose_mapping() to free up the virtal IRQ number,
CPU 1 comes in and calls msi_bitmap_alloc_hwirqs() to allocate an
MSI, and gets the same hardware IRQ number that CPU 0 just freed.
CPU 1 then calls irq_create_mapping() to get a virtual IRQ number,
which sees that there is currently a mapping for that hardware IRQ
number and returns the corresponding virtual IRQ number (which is
the same virtual IRQ number that CPU 0 was using).  CPU 0 then
calls irq_dispose_mapping() and frees that virtual IRQ number.
Now, if another CPU comes along and calls irq_create_mapping(), it
is likely to get the virtual IRQ number that was just freed,
resulting in the same virtual IRQ number apparently being used for
two different hardware interrupts.

To fix this race, we just move the call to msi_bitmap_free_hwirqs()
to after the call to irq_dispose_mapping().  Since virq_to_hw()
doesn't work for the virtual IRQ number after irq_dispose_mapping()
has been called, we need to call it before irq_dispose_mapping() and
remember the result for the msi_bitmap_free_hwirqs() call.

The pattern of calling msi_bitmap_free_hwirqs() before
irq_dispose_mapping() appears in 5 places under arch/powerpc, and
appears to have originated in commit 05af7bd2 ("[POWERPC] MPIC
U3/U4 MSI backend") from 2007.

Fixes: 05af7bd2 ("[POWERPC] MPIC U3/U4 MSI backend")
Reported-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
[bwh: Backported to 3.2:
 - powernv uses a private functions instead of msi_bitmap_free_hwirqs()
 - Adjust filename, context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a077224f upstream.

While working on the 32-bit ARM port of UEFI, I noticed a strange
corruption in the kernel log. The following snprintf() statement
(in drivers/firmware/efi/efi.c:efi_md_typeattr_format())

	snprintf(pos, size, "|%3s|%2s|%2s|%2s|%3s|%2s|%2s|%2s|%2s]",

was producing the following output in the log:

	|    |   |   |   |    |WB|WT|WC|UC]
	|    |   |   |   |    |WB|WT|WC|UC]
	|    |   |   |   |    |WB|WT|WC|UC]
	|RUN|   |   |   |    |WB|WT|WC|UC]*
	|RUN|   |   |   |    |WB|WT|WC|UC]*
	|    |   |   |   |    |WB|WT|WC|UC]
	|RUN|   |   |   |    |WB|WT|WC|UC]*
	|    |   |   |   |    |WB|WT|WC|UC]
	|RUN|   |   |   |    |   |   |   |UC]
	|RUN|   |   |   |    |   |   |   |UC]

As it turns out, this is caused by incorrect code being emitted for
the string() function in lib/vsprintf.c. The following code

	if (!(spec.flags & LEFT)) {
		while (len < spec.field_width--) {
			if (buf < end)
				*buf = ' ';
			++buf;
		}
	}
	for (i = 0; i < len; ++i) {
		if (buf < end)
			*buf = *s;
		++buf; ++s;
	}
	while (len < spec.field_width--) {
		if (buf < end)
			*buf = ' ';
		++buf;
	}

when called with len == 0, triggers an issue in the GCC SRA optimization
pass (Scalar Replacement of Aggregates), which handles promotion of signed
struct members incorrectly. This is a known but as yet unresolved issue.
(https://gcc.gnu.org/bugzilla/show_bug.cgi?id=65932). In this particular
case, it is causing the second while loop to be executed erroneously a
single time, causing the additional space characters to be printed.

So disable the optimization by passing -fno-ipa-sra.
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 294ab783 upstream.

It looks like the Kconfig check that was meant to fix this (commit
fe9233fb [SCSI] scsi_dh: fix kconfig related
build errors) was actually reversed, but no-one noticed until the new set of
patches which separated DM and SCSI_DH).

Fixes: fe9233fbSigned-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit b4cc0efe upstream.

Fix B-tree corruption when a new record is inserted at position 0 in the
node in hfs_brec_insert().

This is an identical change to the corresponding hfs b-tree code to Sergei
Antonov's "hfsplus: fix B-tree corruption after insertion at position 0",
to keep similar code paths in the hfs and hfsplus drivers in sync, where
appropriate.
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Sergei Antonov <saproj@gmail.com>
Cc: Joe Perches <joe@perches.com>
Reviewed-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Anton Altaparmakov <anton@tuxera.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7cb74be6 upstream.

Pages looked up by __hfs_bnode_create() (called by hfs_bnode_create() and
hfs_bnode_find() for finding or creating pages corresponding to an inode)
are immediately kmap()'ed and used (both read and write) and kunmap()'ed,
and should not be page_cache_release()'ed until hfs_bnode_free().

This patch fixes a problem I first saw in July 2012: merely running "du"
on a large hfsplus-mounted directory a few times on a reasonably loaded
system would get the hfsplus driver all confused and complaining about
B-tree inconsistencies, and generates a "BUG: Bad page state".  Most
recently, I can generate this problem on up-to-date Fedora 22 with shipped
kernel 4.0.5, by running "du /" (="/" + "/home" + "/mnt" + other smaller
mounts) and "du /mnt" simultaneously on two windows, where /mnt is a
lightly-used QEMU VM image of the full Mac OS X 10.9:

$ df -i / /home /mnt
Filesystem                  Inodes   IUsed      IFree IUse% Mounted on
/dev/mapper/fedora-root    3276800  551665    2725135   17% /
/dev/mapper/fedora-home   52879360  716221   52163139    2% /home
/dev/nbd0p2             4294967295 1387818 4293579477    1% /mnt

After applying the patch, I was able to run "du /" (60+ times) and "du
/mnt" (150+ times) continuously and simultaneously for 6+ hours.

There are many reports of the hfsplus driver getting confused under load
and generating "BUG: Bad page state" or other similar issues over the
years.  [1]

The unpatched code [2] has always been wrong since it entered the kernel
tree.  The only reason why it gets away with it is that the
kmap/memcpy/kunmap follow very quickly after the page_cache_release() so
the kernel has not had a chance to reuse the memory for something else,
most of the time.

The current RW driver appears to have followed the design and development
of the earlier read-only hfsplus driver [3], where-by version 0.1 (Dec
2001) had a B-tree node-centric approach to
read_cache_page()/page_cache_release() per bnode_get()/bnode_put(),
migrating towards version 0.2 (June 2002) of caching and releasing pages
per inode extents.  When the current RW code first entered the kernel [2]
in 2005, there was an REF_PAGES conditional (and "//" commented out code)
to switch between B-node centric paging to inode-centric paging.  There
was a mistake with the direction of one of the REF_PAGES conditionals in
__hfs_bnode_create().  In a subsequent "remove debug code" commit [4], the
read_cache_page()/page_cache_release() per bnode_get()/bnode_put() were
removed, but a page_cache_release() was mistakenly left in (propagating
the "REF_PAGES <-> !REF_PAGE" mistake), and the commented-out
page_cache_release() in bnode_release() (which should be spanned by
!REF_PAGES) was never enabled.

References:
[1]:
Michael Fox, Apr 2013
http://www.spinics.net/lists/linux-fsdevel/msg63807.html
("hfsplus volume suddenly inaccessable after 'hfs: recoff %d too large'")

Sasha Levin, Feb 2015
http://lkml.org/lkml/2015/2/20/85 ("use after free")

https://bugs.launchpad.net/ubuntu/+source/linux/+bug/740814
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1027887
https://bugzilla.kernel.org/show_bug.cgi?id=42342
https://bugzilla.kernel.org/show_bug.cgi?id=63841
https://bugzilla.kernel.org/show_bug.cgi?id=78761

[2]:
http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/\
fs/hfs/bnode.c?id=d1081202
commit d1081202
Author: Andrew Morton <akpm@osdl.org>
Date:   Wed Feb 25 16:17:36 2004 -0800

    [PATCH] HFS rewrite

http://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/\
fs/hfsplus/bnode.c?id=91556682

commit 91556682
Author: Andrew Morton <akpm@osdl.org>
Date:   Wed Feb 25 16:17:48 2004 -0800

    [PATCH] HFS+ support

[3]:
http://sourceforge.net/projects/linux-hfsplus/

http://sourceforge.net/projects/linux-hfsplus/files/Linux%202.4.x%20patch/hfsplus%200.1/
http://sourceforge.net/projects/linux-hfsplus/files/Linux%202.4.x%20patch/hfsplus%200.2/

http://linux-hfsplus.cvs.sourceforge.net/viewvc/linux-hfsplus/linux/\
fs/hfsplus/bnode.c?r1=1.4&r2=1.5

Date:   Thu Jun 6 09:45:14 2002 +0000
Use buffer cache instead of page cache in bnode.c. Cache inode extents.

[4]:
http://git.kernel.org/cgit/linux/kernel/git/\
stable/linux-stable.git/commit/?id=a5e3985f

commit a5e3985f
Author: Roman Zippel <zippel@linux-m68k.org>
Date:   Tue Sep 6 15:18:47 2005 -0700

[PATCH] hfs: remove debug code
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Anton Altaparmakov <anton@tuxera.com>
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Sougata Santra <sougata@tuxera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a068acf2 upstream.

Many file systems that implement the show_options hook fail to correctly
escape their output which could lead to unescaped characters (e.g.  new
lines) leaking into /proc/mounts and /proc/[pid]/mountinfo files.  This
could lead to confusion, spoofed entries (resulting in things like
systemd issuing false d-bus "mount" notifications), and who knows what
else.  This looks like it would only be the root user stepping on
themselves, but it's possible weird things could happen in containers or
in other situations with delegated mount privileges.

Here's an example using overlay with setuid fusermount trusting the
contents of /proc/mounts (via the /etc/mtab symlink).  Imagine the use
of "sudo" is something more sneaky:

  $ BASE="ovl"
  $ MNT="$BASE/mnt"
  $ LOW="$BASE/lower"
  $ UP="$BASE/upper"
  $ WORK="$BASE/work/ 0 0
  none /proc fuse.pwn user_id=1000"
  $ mkdir -p "$LOW" "$UP" "$WORK"
  $ sudo mount -t overlay -o "lowerdir=$LOW,upperdir=$UP,workdir=$WORK" none /mnt
  $ cat /proc/mounts
  none /root/ovl/mnt overlay rw,relatime,lowerdir=ovl/lower,upperdir=ovl/upper,workdir=ovl/work/ 0 0
  none /proc fuse.pwn user_id=1000 0 0
  $ fusermount -u /proc
  $ cat /proc/mounts
  cat: /proc/mounts: No such file or directory

This fixes the problem by adding new seq_show_option and
seq_show_option_n helpers, and updating the vulnerable show_option
handlers to use them as needed.  Some, like SELinux, need to be open
coded due to unusual existing escape mechanisms.

[akpm@linux-foundation.org: add lost chunk, per Kees]
[keescook@chromium.org: seq_show_option should be using const parameters]
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Acked-by: Jan Kara <jack@suse.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Cc: J. R. Okajima <hooanon05g@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
[lizf: Backported to 3.4:
 - adjust context
 - one more place in ceph needs to be changed
 - drop changes to overlayfs
 - drop showing vers in cifs]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 71c6da84 upstream.

Currently context size (cra_ctxsize) doesn't specified for
ghash_async_alg. Which means it's zero. Thus crypto_create_tfm()
doesn't allocate needed space for ghash_async_ctx, so any
read/write to ctx (e.g. in ghash_async_init_tfm()) is not valid.
Signed-off-by: Andrey Ryabinin <aryabinin@odin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit f49a26e7 upstream.

Update ctime and mtime when a directory is modified. (though OS/2 doesn't
update them anyway)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit b632ffa7 upstream.

We have many WR opcodes that are only supported in kernel space
and/or require optional information to be copied into the WR
structure.  Reject all those not explicitly handled so that we
can't pass invalid information to drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 09bfda10 upstream.

With the radeon driver loaded the HP Compaq dc5750
Small Form Factor machine fails to resume from suspend.
Adding a quirk similar to other devices avoids
the problem and the system resumes properly.
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 35d4a0b6 upstream.

Fixes: 2a72f212 ("IB/uverbs: Remove dev_table")

Before this commit there was a device look-up table that was protected
by a spin_lock used by ib_uverbs_open and by ib_uverbs_remove_one. When
it was dropped and container_of was used instead, it enabled the race
with remove_one as dev might be freed just after:
dev = container_of(inode->i_cdev, struct ib_uverbs_device, cdev) but
before the kref_get.

In addition, this buggy patch added some dead code as
container_of(x,y,z) can never be NULL and so dev can never be NULL.
As a result the comment above ib_uverbs_open saying "the open method
will either immediately run -ENXIO" is wrong as it can never happen.

The solution follows Jason Gunthorpe suggestion from below URL:
https://www.mail-archive.com/linux-rdma@vger.kernel.org/msg25692.html

cdev will hold a kref on the parent (the containing structure,
ib_uverbs_device) and only when that kref is released it is
guaranteed that open will never be called again.

In addition, fixes the active count scheme to use an atomic
not a kref to prevent WARN_ON as pointed by above comment
from Jason.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Reviewed-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 5e99b139 upstream.

The mlx4 IB driver implementation for ib_query_ah used a wrong offset
(28 instead of 29) when link type is Ethernet. Fixed to use the correct one.

Fixes: fa417f7b ('IB/mlx4: Add support for IBoE')
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 0c78789e upstream.

In case the reconnection attempt fails.
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[lizf: Backported to 3.4: add definition of variable xprt]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7f5dcaf1 upstream.

The unregister path of platform_device is broken. On registration, it
will register all resources with either a parent already set, or
type==IORESOURCE_{IO,MEM}. However, on unregister it will release
everything with type==IORESOURCE_{IO,MEM}, but ignore the others. There
are also cases where resources don't get registered in the first place,
like with devices created by of_platform_populate()*.

Fix the unregister path to be symmetrical with the register path by
checking the parent pointer instead of the type field to decide which
resources to unregister. This is safe because the upshot of the
registration path algorithm is that registered resources have a parent
pointer, and non-registered resources do not.

* It can be argued that of_platform_populate() should be registering
  it's resources, and they argument has some merit. However, there are
  quite a few platforms that end up broken if we try to do that due to
  overlapping resources in the device tree. Until that is fixed, we need
  to solve the immediate problem.

Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Tested-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 3a496b00 upstream.

If the internal call to of_address_to_resource() fails, we end up
looping forever in of_find_matching_node_by_address().  This can be
caused by a defective device tree, or calling with an incorrect
matches argument.

Fix by calling of_find_matching_node() unconditionally at the end of
the loop.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 924f92bf upstream.

Most of the time this isn't an issue since hotplugging an adaptor will
trigger a crtc mode change which in turn, causes the driver to probe
every DisplayPort for a dpcd. However, in cases where hotplugging
doesn't cause a mode change (specifically when one unplugs a monitor
from a DisplayPort connector, then plugs that same monitor back in
seconds later on the same port without any other monitors connected), we
never probe for the dpcd before starting the initial link training. What
happens from there looks like this:

	- GPU has only one monitor connected. It's connected via
	  DisplayPort, and does not go through an adaptor of any sort.

	- User unplugs DisplayPort connector from GPU.

	- Change in HPD is detected by the driver, we probe every
	  DisplayPort for a possible connection.

	- Probe the port the user originally had the monitor connected
	  on for it's dpcd. This fails, and we clear the first (and only
	  the first) byte of the dpcd to indicate we no longer have a
	  dpcd for this port.

	- User plugs the previously disconnected monitor back into the
	  same DisplayPort.

	- radeon_connector_hotplug() is called before everyone else,
	  and tries to handle the link training. Since only the first
	  byte of the dpcd is zeroed, the driver is able to complete
	  link training but does so against the wrong dpcd, causing it
	  to initialize the link with the wrong settings.

	- Display stays blank (usually), dpcd is probed after the
	  initial link training, and the driver prints no obvious
	  messages to the log.

In theory, since only one byte of the dpcd is chopped off (specifically,
the byte that contains the revision information for DisplayPort), it's
not entirely impossible that this bug may not show on certain monitors.
For instance, the only reason this bug was visible on my ASUS PB238
monitor was due to the fact that this monitor using the enhanced framing
symbol sequence, the flag for which is ignored if the radeon driver
thinks that the DisplayPort version is below 1.1.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 5556e7e6 upstream.

Consider eCryptfs dcache entries to be stale when the corresponding
lower inode's i_nlink count is zero. This solves a problem caused by the
lower inode being directly modified, without going through the eCryptfs
mount, leaving stale eCryptfs dentries cached and the eCryptfs inode's
i_nlink count not being cleared.
Signed-off-by: Tyler Hicks <tyhicks@canonical.com>
Reported-by: Richard Weinberger <richard@nod.at>
[bwh: Backported to 3.2:
 - Test d_revalidate pointer directly rather than a DCACHE_OP flag
 - Open-code d_inode()
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 1fb8dc36 upstream.

CustomWare uses the FTDI VID with custom PIDs for their ShipModul MiniPlex
products.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 0521cfd0 upstream.

The ehci platform device's drvdata is the pointer of struct usb_hcd
already, so we doesn't need to call bus_to_hcd conversion again.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit efcbc04e upstream.

It is unusual to combine the open flags O_RDONLY and O_EXCL, but
it appears that libre-office does just that.

[pid  3250] stat("/home/USER/.config", {st_mode=S_IFDIR|0700, st_size=8192, ...}) = 0
[pid  3250] open("/home/USER/.config/libreoffice/4-suse/user/extensions/buildid", O_RDONLY|O_EXCL <unfinished ...>

NFSv4 takes O_EXCL as a sign that a setattr command should be sent,
probably to reset the timestamps.

When it was an O_RDONLY open, the SETATTR command does not
identify any actual attributes to change.
If no delegation was provided to the open, the SETATTR uses the
all-zeros stateid and the request is accepted (at least by the
Linux NFS server - no harm, no foul).

If a read-delegation was provided, this is used in the SETATTR
request, and a Netapp filer will justifiably claim
NFS4ERR_BAD_STATEID, which the Linux client takes as a sign
to retry - indefinitely.

So only treat O_EXCL specially if O_CREAT was also given.
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit fe2b5921 upstream.

wf_unregister_client() increments the client count when a client
unregisters. That is obviously incorrect. Decrement that client count
instead.

Fixes: 75722d39 ("[PATCH] ppc64: Thermal control for SMU based machines")
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 64526370 upstream.

Currently, devres_get() passes devres_free() the pointer to devres,
but devres_free() should be given with the pointer to resource data.

Fixes: 9ac7849e ("devres: device resource management")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit bab383de upstream.

parport_find_base() will implicitly do parport_get_port() which
increases the refcount. Then parport_register_device() will again
increment the refcount. But while unloading the module we are only
doing parport_unregister_device() decrementing the refcount only once.
We add an parport_put_port() to neutralize the effect of
parport_get_port().
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 199dc6ed upstream.

When a (e.g.) RAID5 array is reshaped to RAID0, the updating
of queue parameters (e.g. max number of sectors per bio) is
done in the wrong place.
It should be part of ->run, but it is actually part of ->takeover.
This means it happens before level_store() calls:

	blk_set_stacking_limits(&mddev->queue->limits);

and so it ineffective.  This can lead to errors from underlying
devices.

So move all the relevant settings out of create_stripe_zones()
and into raid0_run().

As this can lead to a bug-on it is suitable for any -stable
kernel which supports reshape to RAID0.  So 2.6.35 or later.
As the bug has been present for five years there is no urgency,
so no need to rush into -stable.

Fixes: 9af204cf ("md: Add support for Raid5->Raid0 and Raid10->Raid0 takeover")
Reported-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.com>
[lizf: Backported to 3.4:
 - adjust context
 - remove changes to discard and write-same features]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 9d11b51c upstream.

The Linux NFS server returns garbage in the data payload of inline
NFS/RDMA READ replies. These are READs of under 1000 bytes or so
where the client has not provided either a reply chunk or a write
list.

The NFS server delivers the data payload for an NFS READ reply to
the transport in an xdr_buf page list. If the NFS client did not
provide a reply chunk or a write list, send_reply() is supposed to
set up a separate sge for the page containing the READ data, and
another sge for XDR padding if needed, then post all of the sges via
a single SEND Work Request.

The problem is send_reply() does not advance through the xdr_buf
when setting up scatter/gather entries for SEND WR. It always calls
dma_map_xdr with xdr_off set to zero. When there's more than one
sge, dma_map_xdr() sets up the SEND sge's so they all point to the
xdr_buf's head.

The current Linux NFS/RDMA client always provides a reply chunk or
a write list when performing an NFS READ over RDMA. Therefore, it
does not exercise this particular case. The Linux server has never
had to use more than one extra sge for building RPC/RDMA replies
with a Linux client.

However, an NFS/RDMA client _is_ allowed to send small NFS READs
without setting up a write list or reply chunk. The NFS READ reply
fits entirely within the inline reply buffer in this case. This is
perhaps a more efficient way of performing NFS READs that the Linux
NFS/RDMA client may some day adopt.

Fixes: b432e6b3 ('svcrdma: Change DMA mapping logic to . . .')
BugLink: https://bugzilla.linux-nfs.org/show_bug.cgi?id=285Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 1c2cb594 upstream.

The EPOW interrupt handler uses rtas_get_sensor(), which in turn
uses rtas_busy_delay() to wait for RTAS becoming ready in case it
is necessary. But rtas_busy_delay() is annotated with might_sleep()
and thus may not be used by interrupts handlers like the EPOW handler!
This leads to the following BUG when CONFIG_DEBUG_ATOMIC_SLEEP is
enabled:

 BUG: sleeping function called from invalid context at arch/powerpc/kernel/rtas.c:496
 in_atomic(): 1, irqs_disabled(): 1, pid: 0, name: swapper/1
 CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.2.0-rc2-thuth #6
 Call Trace:
 [c00000007ffe7b90] [c000000000807670] dump_stack+0xa0/0xdc (unreliable)
 [c00000007ffe7bc0] [c0000000000e1f14] ___might_sleep+0x134/0x180
 [c00000007ffe7c20] [c00000000002aec0] rtas_busy_delay+0x30/0xd0
 [c00000007ffe7c50] [c00000000002bde4] rtas_get_sensor+0x74/0xe0
 [c00000007ffe7ce0] [c000000000083264] ras_epow_interrupt+0x44/0x450
 [c00000007ffe7d90] [c000000000120260] handle_irq_event_percpu+0xa0/0x300
 [c00000007ffe7e70] [c000000000120524] handle_irq_event+0x64/0xc0
 [c00000007ffe7eb0] [c000000000124dbc] handle_fasteoi_irq+0xec/0x260
 [c00000007ffe7ef0] [c00000000011f4f0] generic_handle_irq+0x50/0x80
 [c00000007ffe7f20] [c000000000010f3c] __do_irq+0x8c/0x200
 [c00000007ffe7f90] [c0000000000236cc] call_do_irq+0x14/0x24
 [c00000007e6f39e0] [c000000000011144] do_IRQ+0x94/0x110
 [c00000007e6f3a30] [c000000000002594] hardware_interrupt_common+0x114/0x180

Fix this issue by introducing a new rtas_get_sensor_fast() function
that does not use rtas_busy_delay() - and thus can only be used for
sensors that do not cause a BUSY condition - known as "fast" sensors.

The EPOW sensor is defined to be "fast" in sPAPR - mpe.

Fixes: 587f83e8 ("powerpc/pseries: Use rtas_get_sensor in RAS code")
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7aa6ca4d upstream.

Set the PCI_DEV_FLAGS_VPD_REF_F0 flag on all Intel Ethernet device
functions other than function 0, so that on multi-function devices, we will
always read VPD from function 0 instead of from the other functions.

[bhelgaas: changelog]
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
[bwh: Backported to 3.2:
 - Put the class check in the new function as there is no
   DECLARE_PCI_FIXUP_CLASS_EARLY(
 - Adjust context]
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 932c435c upstream.

Add a dev_flags bit, PCI_DEV_FLAGS_VPD_REF_F0, to access VPD through
function 0 to provide VPD access on other functions.  This is for hardware
devices that provide copies of the same VPD capability registers in
multiple functions.  Because the kernel expects that each function has its
own registers, both the locking and the state tracking are affected by VPD
accesses to different functions.

On such devices for example, if a VPD write is performed on function 0,
*any* later attempt to read VPD from any other function of that device will
hang.  This has to do with how the kernel tracks the expected value of the
F bit per function.

Concurrent accesses to different functions of the same device can not only
hang but also corrupt both read and write VPD data.

When hangs occur, typically the error message:

  vpd r/w failed.  This is likely a firmware bug on this device.

will be seen.

Never set this bit on function 0 or there will be an infinite recursion.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 3633ebeb upstream.

We already set a station to be associated when peering completes, both
in user space and in the kernel.  Thus we should always have an
associated sta before sending data frames to that station.

Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized.  This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.
Reported-by: Alexis Green <agreen@cococorp.com>
Tested-by: Jesse Jones <jjones@cococorp.com>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit d1541dc9 upstream.

In fixup_ti816x_class(), we assigned "class = PCI_CLASS_MULTIMEDIA_VIDEO".
But PCI_CLASS_MULTIMEDIA_VIDEO is only the two-byte base class/sub-class
and needs to be shifted to make space for the low-order interface byte.

Shift PCI_CLASS_MULTIMEDIA_VIDEO to set the correct class code.

Fixes: 63c44080 ("PCI: Add quirk for setting valid class for TI816X Endpoint")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Hemant Pedanekar <hemantp@ti.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit a66b0c41 upstream.

The input_dev is already gone when the rc device is being unregistered
so checking for its presence only means that no remove uevent will be
generated.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 7cae2bed upstream.

As reported at https://bugs.launchpad.net/qemu/+bug/1494350,
it is possible to have vcpu->arch.st.last_steal initialized
from a thread other than vcpu thread, say the iothread, via
KVM_SET_MSRS.

Which can cause an overflow later (when subtracting from vcpu threads
sched_info.run_delay).

To avoid that, move steal time accumulation to vcpu entry time,
before copying steal time data to guest.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Reviewed-by: David Matlack <dmatlack@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 2871c69e upstream.

Commit 4c7e3093 ("dm btree remove: fix bug in redistribute3") wasn't
a complete fix for redistribute3().

The redistribute3 function takes 3 btree nodes and shares out the entries
evenly between them.  If the three nodes in total contained
(MAX_ENTRIES * 3) - 1 entries between them then this was erroneously getting
rebalanced as (MAX_ENTRIES - 1) on the left and right, and (MAX_ENTRIES + 1) in
the center.

Fix this issue by being more careful about calculating the target number
of entries for the left and right nodes.

Unit tested in userspace using this program:
https://github.com/jthornber/redistribute3-test/blob/master/redistribute3_t.cSigned-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit c4509601 upstream.

The assignement of EP transfer resources was not handled properly in the
dwc3 driver. Commit aebda618 ("usb: dwc3: Reset the transfer
resource index on SET_INTERFACE") previously fixed one aspect of this
where resources may be exhausted with multiple calls to SET_INTERFACE.
However, it introduced an issue where composite devices with multiple
interfaces can be assigned the same transfer resources for different
endpoints. This patch solves both issues.

The assignment of transfer resources cannot perfectly follow the data
book due to the fact that the controller driver does not have all
knowledge of the configuration in advance. It is given this information
piecemeal by the composite gadget framework after every
SET_CONFIGURATION and SET_INTERFACE. Trying to follow the databook
programming model in this scenario can cause errors. For two reasons:

1) The databook says to do DEPSTARTCFG for every SET_CONFIGURATION and
SET_INTERFACE (8.1.5). This is incorrect in the scenario of multiple
interfaces.

2) The databook does not mention doing more DEPXFERCFG for new endpoint
on alt setting (8.1.6).

The following simplified method is used instead:

All hardware endpoints can be assigned a transfer resource and this
setting will stay persistent until either a core reset or hibernation.
So whenever we do a DEPSTARTCFG(0) we can go ahead and do DEPXFERCFG for
every hardware endpoint as well. We are guaranteed that there are as
many transfer resources as endpoints.

This patch triggers off of the calling dwc3_gadget_start_config() for
EP0-out, which always happens first, and which should only happen in one
of the above conditions.

Fixes: aebda618 ("usb: dwc3: Reset the transfer resource index on SET_INTERFACE")
Reported-by: Ravi Babu <ravibabu@ti.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
[lizf: Backported to 3.4: adjust context]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit 42e3121d upstream.

AudioQuest DragonFly DAC reports a volume control range of 0..50
(0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which
is obviously incorrect and would cause software using the dB information
in e.g. volume sliders to have a massive volume difference in 100..102%
range.

Commit 2d1cb7f6 ("ALSA: usb-audio: add dB range mapping for some
devices") added a dB range mapping for it with range 0..50 dB.

However, the actual volume mapping seems to be neither linear volume nor
linear dB scale, but instead quite close to the cubic mapping e.g.
alsamixer uses, with a range of approx. -53...0 dB.

Replace the previous quirk with a custom dB mapping based on some basic
output measurements, using a 10-item range TLV (which will still fit in
alsa-lib MAX_TLV_RANGE_SIZE).

Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the
range is 0..50, so if this gets fixed/changed in later HW revisions it
will no longer be applied.

v2: incorporated Takashi Iwai's suggestion for the quirk application
method
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
[lizf: Backoported to 3.4: use dev_info() instead of usb_audio_info()]
Signed-off-by: Zefan Li <lizefan@huawei.com>

commit bf1d1c9b upstream.

Add a DECLARE_TLV_DB_RANGE() macro so that dB range information
can be specified without having to count the items manually for
TLV_DB_RANGE_HEAD().
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Zefan Li <lizefan@huawei.com>