We just added phy_do_ioctl, but it turned out that we need another
version of this function that doesn't check whether net_device is
running. So rename phy_do_ioctl to phy_do_ioctl_running.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

snprintf returns the number of bytes that would be written, which may be
greater than the the actual length to be written. Here use extra code to
handle this.

scnprintf returns the number of bytes that was actually written, just use
scnprintf to simplify the code.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The return value of snprintf may be greater than the size of
HNS3_DBG_READ_LEN, use scnprintf instead in hns3_dbg_cmd_read.
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Leon Romanovsky says:

====================
Use ODP MRs for kernel ULPs

The following series extends MR creation routines to allow creation of
user MRs through kernel ULPs as a proxy. The immediate use case is to
allow RDS to work over FS-DAX, which requires ODP (on-demand-paging)
MRs to be created and such MRs were not possible to create prior this
series.

The first part of this patchset extends RDMA to have special verb
ib_reg_user_mr(). The common use case that uses this function is a
userspace application that allocates memory for HCA access but the
responsibility to register the memory at the HCA is on an kernel ULP.
This ULP acts as an agent for the userspace application.

The second part provides advise MR functionality for ULPs. This is
integral part of ODP flows and used to trigger pagefaults in advance
to prepare memory before running working set.

The third part is actual user of those in-kernel APIs.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Adjust SPAN egress mirroring buffer size handling for Spectrum-2

Jiri says:

For Spectrum-2 the computation of SPAN egress mirroring buffer uses a
different formula. On top of MTU it needs also current port speed. Fix
the computation and also trigger the buffer size set according to PUDE
event, which happens when port speed changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When PUDE event is handled and the link is up, update the port SPAN
buffer size according to the current speed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For SPAN egress mirroring buffer size, it is needed to use a different
formula for Spectrum and Spectrum-2. Move the buffer size computation to
ops and implement new formula for Spectrum-2.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Avoid duplication of code that is doing buffsize update and put it into
a separate helper function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently PTP code queries directly PTYS register for port speed from
work scheduled upon PUDE event. Since the speed needs to be used for
SPAN buffer size computation as well, push the code into a separate
helper.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
net: phy: add generic ndo_do_ioctl handler phy_do_ioctl

A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib. As first user convert r8169.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Replace rtl8169_ioctl with new generic function phy_do_ioctl.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

A number of network drivers has the same glue code to use phy_mii_ioctl
as ndo_do_ioctl handler. So let's add such a generic ndo_do_ioctl
handler to phylib.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The SERDES statistics are valid for all members of the 6390 family,
not just the 6390 itself. Add the needed callbacks to all members of
the family.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

USXGMII supports passing link information in-band between PHY and MAC PCS,
add it to the list of protocols that support in-band AN mode.

Being a MAC-PHY protocol that can auto-negotiate link speeds up to 10
Gbps, we populate the initial supported mask with the entire spectrum of
link modes up to 10G that PHYLINK supports, and we let the driver reduce
that mask in its .phylink_validate method.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The APIs can be used by Ethernet drivers without actually loading a PHY
driver. This may become more widespread in the future with 802.3z
compatible MAC PCS devices being locally driven by the MAC driver when
configuring for a PHY mode with in-band negotiation.

Check that drv is not NULL before reading from it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For some reason, PHYLINK does not put the copper modes for 802.3bz
(NBASE-T) and 802.3an-2006 (10GBASE-T) in the PHY's supported mask, when
the PHY-MAC connection is a 10G-capable one (10GBase-KR, 10GBase-R,
USXGMII). One possible way through which the cable side can work at the
lower speed is by having the PHY emit PAUSE frames towards the MAC. So
fix that omission.

Also include the 2500Base-X fiber mode in this list while we're at it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

snps databook noted that physical coding sublayer (PCS) interface
that can be used when the MAC is configured for the TBI, RTBI, or
SGMII PHY interface. we have RGMII and SGMII in a SoC and it also
has the PCS block. it needs stmmac_init_phy and stmmac_mdio_register
function for initializing phy when it used RGMII interface.
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull RISC-V fixes from Paul Walmsley:
 "Three fixes for RISC-V:

   - Don't free and reuse memory containing the code that CPUs parked at
     boot reside in.

   - Fix rv64 build problems for ubsan and some modules by adding
     logical and arithmetic shift helpers for 128-bit values. These are
     from libgcc and are similar to what's present for ARM64.

   - Fix vDSO builds to clean up their own temporary files"

* tag 'riscv/for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Less inefficient gcc tishift helpers (and export their symbols)
  riscv: delete temporary files
  riscv: make sure the cores stay looping in .Lsecondary_park

Pull networking fixes from David Miller:

 1) Fix non-blocking connect() in x25, from Martin Schiller.

 2) Fix spurious decryption errors in kTLS, from Jakub Kicinski.

 3) Netfilter use-after-free in mtype_destroy(), from Cong Wang.

 4) Limit size of TSO packets properly in lan78xx driver, from Eric
    Dumazet.

 5) r8152 probe needs an endpoint sanity check, from Johan Hovold.

 6) Prevent looping in tcp_bpf_unhash() during sockmap/tls free, from
    John Fastabend.

 7) hns3 needs short frames padded on transmit, from Yunsheng Lin.

 8) Fix netfilter ICMP header corruption, from Eyal Birger.

 9) Fix soft lockup when low on memory in hns3, from Yonglong Liu.

10) Fix NTUPLE firmware command failures in bnxt_en, from Michael Chan.

11) Fix memory leak in act_ctinfo, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (91 commits)
  cxgb4: reject overlapped queues in TC-MQPRIO offload
  cxgb4: fix Tx multi channel port rate limit
  net: sched: act_ctinfo: fix memory leak
  bnxt_en: Do not treat DSN (Digital Serial Number) read failure as fatal.
  bnxt_en: Fix ipv6 RFS filter matching logic.
  bnxt_en: Fix NTUPLE firmware command failures.
  net: systemport: Fixed queue mapping in internal ring map
  net: dsa: bcm_sf2: Configure IMP port for 2Gb/sec
  net: dsa: sja1105: Don't error out on disabled ports with no phy-mode
  net: phy: dp83867: Set FORCE_LINK_GOOD to default after reset
  net: hns: fix soft lockup when there is not enough memory
  net: avoid updating qdisc_xmit_lock_key in netdev_update_lockdep_key()
  net/sched: act_ife: initalize ife->metalist earlier
  netfilter: nat: fix ICMP header corruption on ICMP errors
  net: wan: lapbether.c: Use built-in RCU list checking
  netfilter: nf_tables: fix flowtable list del corruption
  netfilter: nf_tables: fix memory leak in nf_tables_parse_netdev_hooks()
  netfilter: nf_tables: remove WARN and add NLA_STRING upper limits
  netfilter: nft_tunnel: ERSPAN_VERSION must not be null
  netfilter: nft_tunnel: fix null-attribute check
  ...

Pull i2c fixes from Wolfram Sang:
 "Two runtime PM fixes and one leak fix"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: iop3xx: Fix memory leak in probe error path
  i2c: tegra: Properly disable runtime PM on driver's probe error
  i2c: tegra: Fix suspending in active runtime PM state

Ido Schimmel says:

====================
mlxsw: Add tunnel devlink-trap support

This patch set from Amit adds support in mlxsw for tunnel traps and a
few additional layer 3 traps that can report drops and exceptions via
devlink-trap.

These traps allow the user to more quickly diagnose problems relating to
tunnel decapsulation errors, such as packet being too short to
decapsulate or a packet containing wrong GRE key in its GRE header.

Patch set overview:

Patches #1-#4 add three additional layer 3 traps. Two of which are
mlxsw-specific as they relate to hardware-specific errors. The patches
include documentation of each trap and selftests.

Patches #5-#8 are preparations. They ensure that the correct ECN bits
are set in the outer header during IPinIP encapsulation and that packets
with an invalid ECN combination in underlay and overlay are trapped to
the kernel and not decapsulated in hardware.

Patches #9-#15 add support for two tunnel related traps. Each trap is
documented and selftested using both VXLAN and IPinIP tunnels, if
applicable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that the trap is triggered under the right conditions and that
devlink counters increase when action is trap.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a trap for NVE packets that the device decided to drop because their
overlay source MAC is multicast.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add packet trap that can report NVE packets that the device decided to
drop because their overlay source MAC is multicast.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that the trap is triggered under the right conditions and that
devlink counters increase.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Test that the trap is triggered under the right conditions and that
devlink counters increase.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the trap IDs and trap group used to report tunnel drops. Register
tunnel packet traps and associated tunnel trap group with devlink
during driver initialization.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add packet traps that can report packets that were dropped during tunnel
decapsulation.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Move L3_DROPS case to appear after L2_DROPS case.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Initialize ECN mapping registers during router init according to
INET_ECN_encapsulate() and INET_ECN_decapsulate().

For IP-in-IP encapsulation, this is required to ensure that ECN bits in
the underlay are set in accordance with the kernel. For decapsulation,
this is required to ensure that packets with invalid ECN combination in
underlay and overlay are trapped to the kernel and not forwarded.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This register configures the actions that are done during IPinIP
decapsulation based on the ECN bits.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This register performs mapping from overlay ECN to underlay ECN during
IPinIP encapsulation.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a trap for packets that the device decided to drop because they are
not supposed to be routed. For example, IGMP queries can be flooded by
the device in layer 2 and reach the router. Such packets should not be
routed and instead dropped.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add packet trap that can report packets that reached the router, but are
non-routable. For example, IGMP queries can be flooded by the device in
layer 2 and reach the router. Such packets should not be routed and
instead dropped.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add test cases to check that packets routed through disabled RIFs and
packets routed from disabled RIFs are dropped and devlink counters
increase when the action is trap.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

IRIF_DISABLED and ERIF_DISABLED are driver specific traps. Packets are
dropped for these reasons when they need to be routed through/from
existing router interfaces (RIF) which are disabled.

Add devlink driver-specific traps and mlxsw trap IDs used to report
these traps.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 E-Switch chains and prios

This series has two parts,

1) A merge commit with mlx5-next branch that include updates for mlx5
HW layouts needed for this and upcoming submissions.

2) From Paul, Increase the number of chains and prios

Currently the Mellanox driver supports offloading tc rules that
are defined on the first 4 chains and the first 16 priorities.
The restriction stems from the firmware flow level enforcement
requiring a flow table of a certain level to point to a flow
table of a higher level. This limitation may be ignored by setting
the ignore_flow_level bit when creating flow table entries.
Use unmanaged tables and ignore flow level to create more tables than
declared by fs_core steering. Manually manage the connections between the
tables themselves.

HW table is instantiated for every tc <chain,prio> tuple. The miss rule
of every table either jumps to the next <chain,prio> table, or continues
to slow_fdb. This logic is realized by following this sequence:

1. Create an auto-grouped flow table for the specified priority with
    reserved entries

Reserved entries are allocated at the end of the flow table.
Flow groups are evaluated in sequence and therefore it is guaranteed
that the flow group defined on the last FTEs will be the last to evaluate.

Define a "match all" flow group on the reserved entries, providing
the platform to add table miss actions.

2. Set the miss rule action to jump to the next <chain,prio> table
    or the slow_fdb.

3. Link the previous priority table to point to the new table by
    updating its miss rule.

Please pull and let me know if there's any problem.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

A queue can't belong to multiple traffic classes. So, reject
any such configuration that results in overlapped queues for a
traffic class.

Fixes: b1396c2b ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

T6 can support 2 egress traffic management channels per port to
double the total number of traffic classes that can be configured.
In this configuration, if the class belongs to the other channel,
then all the queues must be bound again explicitly to the new class,
for the rate limit parameters on the other channel to take effect.

So, always explicitly bind all queues to the port rate limit traffic
class, regardless of the traffic management channel that it belongs
to. Also, only bind queues to port rate limit traffic class, if all
the queues don't already belong to an existing different traffic
class.

Fixes: 4ec4762d ("cxgb4: add TC-MATCHALL classifier egress offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>