The ARP trap group will be used for IPv6 ND traps in the next patch, so
rename it to "NEIGH_DISCOVERY" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Now that traffic class (TC) and priority are set to the same value,
there is no need to store both. Remove the first.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The traffic class (TC) attribute of packet traps determines through which
TC a packet trap will be scheduled through the CPU port.

The priority attribute determines which trap will be triggered in case
several packet traps match a packet.

We try to configure these attributes to the same value for all packet
traps as there is little reason not to.

Some packet traps did not use the same value, so rectify that now.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

As explained in commit 9ffcc372 ("mlxsw: spectrum: Allow packets to
be trapped from any PG"), incoming packets can be admitted to the shared
buffer and forwarded / trapped, if:

(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
 Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
 Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)

Trapped packets are scheduled to transmission through the CPU port.
Currently, the minimum and maximum quotas of traffic class (TC) 0 of the
CPU port are 0, which means it is not usable.

Assign non-zero quotas to TC 0 of the CPU port, so that it could be
utilized by subsequent patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Reduce the default acceptable rate of DHCP packets to 128 packets per
second and reduce their priority. This is reasonable given the Spectrum
ASICs are limited to 128 ports at the moment.

These are only the default values. Users will be able to modify them via
devlink-trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently, IPv4 DHCP packets are trapped during L2 forwarding, which
means that packets might be trapped unnecessarily. Instead, only trap
the DHCP packets that reach the router. Either because they were flooded
to the router port or forwarded to it by the FDB. This is consistent
with the corresponding IPv6 trap.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Both packet types are needed for the same reason (multicast snooping),
so associate them with the same trap group.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The IGMP trap group will be used for MLD traps in the next patch, so
rename it to "MC_SNOOPING" which is more appropriate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull EFI fixes from Thomas Gleixner:
 "A set of EFI fixes:

   - Don't return a garbage screen info when EFI framebuffer is not
     available

   - Make the early EFI console work properly with wider fonts instead
     of drawing garbage

   - Prevent a memory buffer leak in allocate_e820()

   - Print the firmware error record properly so it can be decoded by
     users

   - Fix a symbol clash in the host tool build which only happens with
     newer compilers.

   - Add a missing check for the event log version of TPM which caused
     boot failures on several Dell systems due to an attempt to decode
     SHA-1 format with the crypto agile algorithm"

* tag 'efi-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  tpm: check event log version before reading final events
  efi: Pull up arch-specific prototype efi_systab_show_arch()
  x86/boot: Mark global variables as static
  efi: cper: Add support for printing Firmware Error Record Reference
  efi/libstub/x86: Avoid EFI map buffer alloc in allocate_e820()
  efi/earlycon: Fix early printk for wider fonts
  efi/libstub: Avoid returning uninitialized data from setup_graphics()

Pull x86 fixes from Thomas Gleixner:
 "Two fixes for x86:

   - Unbreak stack dumps for inactive tasks by interpreting the special
     first frame left by __switch_to_asm() correctly.

     The recent change not to skip the first frame so ORC and frame
     unwinder behave in the same way caused all entries to be
     unreliable, i.e. prepended with '?'.

   - Use cpumask_available() instead of an implicit NULL check of a
     cpumask_var_t in mmio trace to prevent a Clang build warning"

* tag 'x86-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks
  x86/mmiotrace: Use cpumask_available() for cpumask_var_t variables

Pull scheduler fixes from Thomas Gleixner:
 "A set of fixes for the scheduler:

   - Fix handling of throttled parents in enqueue_task_fair() completely.

     The recent fix overlooked a corner case where the first iteration
     terminates due to an entity already being on the runqueue which
     makes the list management incomplete and later triggers the
     assertion which checks for completeness.

   - Fix a similar problem in unthrottle_cfs_rq().

   - Show the correct uclamp values in procfs which prints the effective
     value twice instead of requested and effective"

* tag 'sched-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  sched/fair: Fix unthrottle_cfs_rq() for leaf_cfs_rq list
  sched/debug: Fix requested task uclamp values shown in procfs
  sched/fair: Fix enqueue_task_fair() warning some more

Pull networking fixes from David Miller:

 1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna
    Bhowmik.

 2) Nexthop attributes aren't being checked properly because of
    mis-initialized iterator, from David Ahern.

 3) Revert iop_idents_reserve() change as it caused performance
    regressions and was just working around what is really a UBSAN bug
    in the compiler. From Yuqi Jin.

 4) Read MAC address properly from ROM in bmac driver (double iteration
    proceeds past end of address array), from Jeremy Kerr.

 5) Add Microsoft Surface device IDs to r8152, from Marc Payne.

 6) Prevent reference to freed SKB in __netif_receive_skb_core(), from
    Boris Sukholitko.

 7) Fix ACK discard behavior in rxrpc, from David Howells.

 8) Preserve flow hash across packet scrubbing in wireguard, from Jason
    A. Donenfeld.

 9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric
    Dumazet.

10) Fix encryption error checking in kTLS code, from Vadim Fedorenko.

11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki.

12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet.

13) Fix use after free in mlxsw driver, from Jiri Pirko.

14) Order kTLS key destruction properly in mlx5 driver, from Tariq
    Toukan.

15) Check devm_platform_ioremap_resource() return value properly in
    several drivers, from Tiezhu Yang.

* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
  net: smsc911x: Fix runtime PM imbalance on error
  net/mlx4_core: fix a memory leak bug.
  net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
  net: phy: mscc: fix initialization of the MACsec protocol mode
  net: stmmac: don't attach interface until resume finishes
  net: Fix return value about devm_platform_ioremap_resource()
  net/mlx5: Fix error flow in case of function_setup failure
  net/mlx5e: CT: Correctly get flow rule
  net/mlx5e: Update netdev txq on completions during closure
  net/mlx5: Annotate mutex destroy for root ns
  net/mlx5: Don't maintain a case of del_sw_func being null
  net/mlx5: Fix cleaning unmanaged flow tables
  net/mlx5: Fix memory leak in mlx5_events_init
  net/mlx5e: Fix inner tirs handling
  net/mlx5e: kTLS, Destroy key object after destroying the TIS
  net/mlx5e: Fix allowed tc redirect merged eswitch offload cases
  net/mlx5: Avoid processing commands before cmdif is ready
  net/mlx5: Fix a race when moving command interface to events mode
  net/mlx5: Add command entry handling completion
  rxrpc: Fix a memory leak in rxkad_verify_response()
  ...

get_coalesce returns 0 or ERRNO, but the return value isn't checked.
The returned coalesce data may be invalid if an ERRNO is set,
therefore better check and propagate the return value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bartosz Golaszewski says:

====================
net: provide a devres variant of register_netdev()

Using devres helpers allows to shrink the probing code, avoid memory leaks in
error paths make sure the order in which resources are freed is the exact
opposite of their allocation. This series proposes to add a devres variant
of register_netdev() that will only work with net_device structures whose
memory is also managed.

First we add the missing documentation entry for the only other networking
devres helper: devm_alloc_etherdev().

Next we move devm_alloc_etherdev() into a separate source file.

We then use a proxy structure in devm_alloc_etherdev() to improve readability.

Last: we implement devm_register_netdev() and use it in mtk-eth-mac driver.

v1 -> v2:
- rebase on top of net-next after driver rename, no functional changes
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Use the new devres variant of register_netdev() in the mtk-star-emac
driver and shrink the code by a couple lines.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Provide devm_register_netdev() - a device resource managed variant
of register_netdev(). This new helper will only work for net_device
structs that are also already managed by devres.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Not using a proxy structure to store struct net_device doesn't save
anything in terms of compiled code size or memory usage but significantly
decreases the readability of the code with all the pointer casting.

Define struct net_device_devres and use it in devm_alloc_etherdev_mqs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There's currently only a single devres helper in net/ - devm variant
of alloc_etherdev. Let's move it to net/devres.c with the intention of
assing a second one: devm_register_netdev(). This new routine will need
to know the address of the release function of devm_alloc_etherdev() so
that it can verify (using devres_find()) that the struct net_device
that's being passed to it is also resource managed.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add a new section for networking devres helpers to devres.rst and list
the two existing devm functions.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: remove mask argument from few ERI/OCP functions

Few ERI/OCP functions have a mask argument that isn't needed.
Remove it to simplify the functions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove the mask argument as it's not used by r8168ep_ocp_read().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

All callers read the full 32bit value, therefore the mask argument can
be removed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

rtl_eri_read() returns the full 32bit value, therefore there's no
benefit in writing back parts of it only. handle it like the vendor
driver and write the full 32 bit always. Omitting the mask argument
avoids some overhead and makes the code better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Remove runtime PM usage counter decrement when the
increment function has not been called to keep the
counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
100GbE Intel Wired LAN Driver Updates 2020-05-22

This series contains updates to virtchnl and the ice driver.

Geert Uytterhoeven fixes a data structure alignment issue in the
virtchnl structures.

Henry adds Flow Director support which allows for the redirection on
ntuple rules over six patches.  Initially Henry adds the initial
infrastructure for Flow Director, and then later adds IPv4 and IPv6
support, as well as being able to display the ntuple rules.

Bret add Accelerated Receive Flow Steering (aRFS) support which is used
to steer receive flows to a specific queue.  Fixes a transmit timeout
when the VF link transitions from up/down/up because the transmit and
receive queue interrupts are not enabled as part of VF's link up.  Fixed
an issue when the default VF LAN address is changed and after reset the
PF will attempt to add the new MAC, which fails because it already
exists. This causes the VF to be disabled completely until it is removed
and enabled via sysfs.

Anirudh (Ani) makes a fix where the ice driver needs to call set_mac_cfg
to enable jumbo frames, so ensure it gets called during initialization
and after reset.  Fix bad register reads during a register dump in
ethtool by removing the bad registers.

Paul fixes an issue where the receive Malicious Driver Detection (MDD)
auto reset message was not being logged because it occurred after the VF
reset.

Victor adds a check for compatibility between the Dynamic Device
Personalization (DDP) package and the NIC firmware to ensure that
everything aligns.

Jesse fixes a administrative queue string call with the appropriate
error reporting variable.  Also fixed the loop variables that are
comparing or assigning signed against unsigned values.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
1GbE Intel Wired LAN Driver Updates 2020-05-22

This series contains updates to e1000e, igc and igb.

Many of the patches in this series are fixes, but many of the igc fixes
are based on the recent filter rule handling Andre has been working,
which will not backport to earlier/stable kernels.  The remaining fixes
for e1000e and igb have CC'd stable where applicable.

Andre continue with his refactoring of the filter rule code to help with
reducing the complexity, in multiple patches.  Fix the inconsistent size
of a struct field.  Fixed an issue where filter rules stay active in the
hardware, even after it was deleted, so make sure to disable the filter
rule before deleting.  Fixed an issue with NFC rules which were dropping
valid multicast MAC address.  Fixed how the NFC rules are restored after
the NIC is reset or brought up, so that they are restored in the same order
they were initially setup in.  Fix a potential memory leak when the
driver is unloaded and the NFC rules are not flushed from memory
properly.  Fixed how NFC rule validation handles when a request to
overwrite an existing rule.  Changed the locking around the NFC rule API
calls from spin_locks to mutex locks to avoid unnecessary busy waiting
on lock contention.

Sasha clean up more unused code in the igc driver.

Kai-Heng Feng from Canonical provides three fixes, first has igb report
the speed and duplex as unknown when in runtime suspend.  Fixed e1000e
to pass up the error when disabling ULP mode.  Fixed e1000e performance
by disabling TSO by default for certain MACs.

Vitaly disables S0ix entry and exit flows for ME systems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5 fixes 2020-05-22

This series introduces some fixes to mlx5 driver.

Please pull and let me know if there is any problem.

For -stable v4.13
   ('net/mlx5: Add command entry handling completion')

For -stable v5.2
   ('net/mlx5: Fix error flow in case of function_setup failure')
   ('net/mlx5: Fix memory leak in mlx5_events_init')

For -stable v5.3
   ('net/mlx5e: Update netdev txq on completions during closure')
   ('net/mlx5e: kTLS, Destroy key object after destroying the TIS')
   ('net/mlx5e: Fix inner tirs handling')

For -stable v5.6
   ('net/mlx5: Fix cleaning unmanaged flow tables')
   ('net/mlx5: Fix a race when moving command interface to events mode')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
mlx5-updates-2020-05-22

This series includes two updates and one cleanup patch

1) Tang Bim, clean-up with IS_ERR() usage

2) Vlad introduces a new mlx5 kconfig flag for TC support

   This is required due to the high volume of current and upcoming
   development in the eswitch and representors areas where some of the
   feature are TC based such as the downstream patches of MPLSoUDP and
   the following representor bonding support for VF live migration and
   uplink representor dynamic loading.
   For this Vlad kept TC specific code in tc.c and rep/tc.c and
   organized non TC code in representors specific files.

3) Eli Cohen adds support for MPLS over UPD encap and decap TC offloads.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix psample build error when CONFIG_INET is not set/enabled by
bracketing the tunnel code in #ifdef CONFIG_NET / #endif.

../net/psample/psample.c: In function ‘__psample_ip_tun_to_nlattr’:
../net/psample/psample.c:216:25: error: implicit declaration of function ‘ip_tunnel_info_opts’; did you mean ‘ip_tunnel_info_opts_set’? [-Werror=implicit-function-declaration]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Yotam Gigi <yotam.gi@gmail.com>
Cc: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In function mlx4_opreq_action(), pointer "mailbox" is not released,
when mlx4_cmd_box() return and error, causing a memory leak bug.
Fix this issue by going to "out" label, mlx4_free_cmd_mailbox() can
free this pointer.

Fixes: fe6f700d ("net/mlx4_core: Respond to operation request by firmware")
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>

vlan_for_each() are required to be called with rtnl_lock taken, otherwise
ASSERT_RTNL() warning will be triggered - which happens now during System
resume from suspend:
  cpsw_suspend()
  |- cpsw_ndo_stop()
    |- __hw_addr_ref_unsync_dev()
      |- cpsw_purge_all_mc()
         |- vlan_for_each()
            |- ASSERT_RTNL();

Hence, fix it by surrounding cpsw_ndo_stop() by rtnl_lock/unlock() calls.

Fixes: 15180eca ("net: ethernet: ti: cpsw: fix vlan mcast")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

At the very end of the MACsec block initialization in the MSCC PHY
driver, the MACsec "protocol mode" is set. This setting should be set
based on the PHY id within the package, as the bank used to access the
register used depends on this. This was not done correctly, and only the
first bank was used leading to the two upper PHYs being unstable when
using the VSC8584. This patch fixes it.

Fixes: 1bbe0ecc ("net: phy: mscc: macsec initialization")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 14b41a29 ("net: stmmac: Delete txtimer in suspend") was the
first attempt to fix a race between mod_timer() and setup_timer()
during stmmac_resume(). However the issue still exists as the commit
only addressed half of the issue.

Same race can still happen as stmmac_resume() re-attaches interface
way too early - even before hardware is fully initialized.  Worse,
doing so allows network traffic to restart and stmmac_tx_timer_arm()
being called in the middle of stmmac_resume(), which re-init tx timers
in stmmac_init_coalesce().  timer_list will be corrupted and system
crashes as a result of race between mod_timer() and setup_timer().

  systemd--1995    2.... 552950018us : stmmac_suspend: 4994
  ksoftirq-9       0..s2 553123133us : stmmac_tx_timer_arm: 2276
  systemd--1995    0.... 553127896us : stmmac_resume: 5101
  systemd--320     7...2 553132752us : stmmac_tx_timer_arm: 2276
  (sd-exec-1999    5...2 553135204us : stmmac_tx_timer_arm: 2276
  ---------------------------------
  pc : run_timer_softirq+0x468/0x5e0
  lr : run_timer_softirq+0x570/0x5e0
  Call trace:
   run_timer_softirq+0x468/0x5e0
   __do_softirq+0x124/0x398
   irq_exit+0xd8/0xe0
   __handle_domain_irq+0x6c/0xc0
   gic_handle_irq+0x60/0xb0
   el1_irq+0xb8/0x180
   arch_cpu_idle+0x38/0x230
   default_idle_call+0x24/0x3c
   do_idle+0x1e0/0x2b8
   cpu_startup_entry+0x28/0x48
   secondary_start_kernel+0x1b4/0x208

Fix this by deferring netif_device_attach() to the end of
stmmac_resume().
Signed-off-by: Leon Yu <leoyu@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ever since its first commit 0ca7111a ("phy: add AT803x driver") the
PHY ID mask was set to 0xffffffef. It is unclear to me why this mask was
chosen in the first place. Both the AR8031/AR8033 and the AR8035
datasheets mention it is always the given value:
 - for AR8031/AR8033 its 0x004d/0xd074
 - for AR8035 its 0x004d/0xd072

Unfortunately, I don't have a datasheet for the AR8030. Therefore, we
leave its PHY ID mask untouched. For the PHYs mentioned before use the
handy PHY_ID_MATCH_EXACT() macro.

I've tried to contact the author of the initial commit, but received no
answer so far.

Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

The srmmu_nocache_init() uses __nocache_fix() macro to add an offset to
page table entry to access srmmu_nocache_pool.

But since sparc32 has only three actual page table levels, pgd, p4d and
pud are essentially the same thing and pgd_offset() and p4d_offset() are
no-ops, the __nocache_fix() should be done only at PUD level.

Remove __nocache_fix() for p4d_offset() and pud_offset() and keep it
only for PUD and lower levels.

Fixes: c2bc26f7 ("sparc32: use PUD rather than PGD to get PMD in srmmu_nocache_init()")
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Anatoly Pugachev <matorola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge misc fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  MAINTAINERS: add files related to kdump
  z3fold: fix use-after-free when freeing handles
  sparc32: use PUD rather than PGD to get PMD in srmmu_nocache_init()
  MAINTAINERS: update email address for Naoya Horiguchi
  sh: include linux/time_types.h for sockios
  kasan: disable branch tracing for core runtime
  selftests/vm/write_to_hugetlbfs.c: fix unused variable warning
  selftests/vm/.gitignore: add mremap_dontunmap
  rapidio: fix an error in get_user_pages_fast() error handling
  x86: bitops: fix build regression
  device-dax: don't leak kernel memory to user space after unloading kmem

Pull driver core fixes from Greg KH:
 "So, turns out the kobject fix didn't quite work, so here are four
  patches that in the end, result in just two driver core fixes for
  reported issues that no one has had problems with.

  The kobject patch that was originally in here has now been reverted,
  as Guenter reported boot problems with it on some of his systems"

* tag 'driver-core-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  Revert "kobject: Make sure the parent does not get released before its children"
  kobject: Make sure the parent does not get released before its children
  driver core: Fix handling of SYNC_STATE_ONLY + STATELESS device links
  driver core: Fix SYNC_STATE_ONLY device link implementation

Pull char/misc fixes from Greg KH:
 "Here are some small char/misc driver fixes for 5.7-rc7 that resolve
  some reported issues. Included in here are tiny fixes for the mei,
  coresight, rtsx, ipack, and mhi drivers.

  All of these have been in linux-next with no reported issues"

* tag 'char-misc-5.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
  misc: rtsx: Add short delay after exit from ASPM
  bus: mhi: core: Fix some error return code
  ipack: tpci200: fix error return code in tpci200_register()
  coresight: cti: remove incorrect NULL return check
  mei: release me_cl object reference