- 08 Jan, 2022 5 commits
-
-
Paolo Abeni authored
MPTCP join self-tests are a bit fragile as they reply on delays instead of events to catch-up with the expected sockets states. Replace the delay with state checking where possible and reduce the number of sleeps in the most complex scenarios. This will both reduce the tests run-time and will improve stability. Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Vladimir Oltean authored
Add support for flushing the MAC table on a given port in the ocelot switch library, and use this functionality in the felix DSA driver. This operation is needed when a port leaves a bridge to become standalone, and when the learning is disabled, and when the STP state changes to a state where no FDB entry should be present. Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by:
Florian Fainelli <f.fainelli@gmail.com> Link: https://lore.kernel.org/r/20220107144229.244584-1-vladimir.oltean@nxp.comSigned-off-by:
-
Vladimir Oltean authored
Assuming the test setup described here: https://patchwork.kernel.org/project/netdevbpf/cover/20210205130240.4072854-1-vladimir.oltean@nxp.com/ (swp1 and swp2 are in bond0, and bond0 is in a bridge with swp0) it can be seen that when swp1 goes down (on either board A or B), then traffic that should go through that port isn't forwarded anywhere. A dump of the PGID table shows the following: PGID_DST[0] = ports 0 PGID_DST[1] = ports 1 PGID_DST[2] = ports 2 PGID_DST[3] = ports 3 PGID_DST[4] = ports 4 PGID_DST[5] = ports 5 PGID_DST[6] = no ports PGID_AGGR[0] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[1] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[2] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[3] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[4] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[5] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[6] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[7] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[8] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[9] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[10] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[11] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[12] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[13] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[14] = ports 0, 1, 2, 3, 4, 5 PGID_AGGR[15] = ports 0, 1, 2, 3, 4, 5 PGID_SRC[0] = ports 1, 2 PGID_SRC[1] = ports 0 PGID_SRC[2] = ports 0 PGID_SRC[3] = no ports PGID_SRC[4] = no ports PGID_SRC[5] = no ports PGID_SRC[6] = ports 0, 1, 2, 3, 4, 5 Whereas a "good" PGID configuration for that setup should have looked like this: PGID_DST[0] = ports 0 PGID_DST[1] = ports 1, 2 PGID_DST[2] = ports 1, 2 PGID_DST[3] = ports 3 PGID_DST[4] = ports 4 PGID_DST[5] = ports 5 PGID_DST[6] = no ports PGID_AGGR[0] = ports 0, 2, 3, 4, 5 PGID_AGGR[1] = ports 0, 2, 3, 4, 5 PGID_AGGR[2] = ports 0, 2, 3, 4, 5 PGID_AGGR[3] = ports 0, 2, 3, 4, 5 PGID_AGGR[4] = ports 0, 2, 3, 4, 5 PGID_AGGR[5] = ports 0, 2, 3, 4, 5 PGID_AGGR[6] = ports 0, 2, 3, 4, 5 PGID_AGGR[7] = ports 0, 2, 3, 4, 5 PGID_AGGR[8] = ports 0, 2, 3, 4, 5 PGID_AGGR[9] = ports 0, 2, 3, 4, 5 PGID_AGGR[10] = ports 0, 2, 3, 4, 5 PGID_AGGR[11] = ports 0, 2, 3, 4, 5 PGID_AGGR[12] = ports 0, 2, 3, 4, 5 PGID_AGGR[13] = ports 0, 2, 3, 4, 5 PGID_AGGR[14] = ports 0, 2, 3, 4, 5 PGID_AGGR[15] = ports 0, 2, 3, 4, 5 PGID_SRC[0] = ports 1, 2 PGID_SRC[1] = ports 0 PGID_SRC[2] = ports 0 PGID_SRC[3] = no ports PGID_SRC[4] = no ports PGID_SRC[5] = no ports PGID_SRC[6] = ports 0, 1, 2, 3, 4, 5 In other words, in the "bad" configuration, the attempt is to remove the inactive swp1 from the destination ports via PGID_DST. But when a MAC table entry is learned, it is learned towards PGID_DST 1, because that is the logical port id of the LAG itself (it is equal to the lowest numbered member port). So when swp1 becomes inactive, if we set PGID_DST[1] to contain just swp1 and not swp2, the packet will not have any chance to reach the destination via swp2. The "correct" way to remove swp1 as a destination is via PGID_AGGR (remove swp1 from the aggregation port groups for all aggregation codes). This means that PGID_DST[1] and PGID_DST[2] must still contain both swp1 and swp2. This makes the MAC table still treat packets destined towards the single-port LAG as "multicast", and the inactive ports are removed via the aggregation code tables. The change presented here is a design one: the ocelot_get_bond_mask() function used to take an "only_active_ports" argument. We don't need that. The only call site that specifies only_active_ports=true, ocelot_set_aggr_pgids(), must retrieve the entire bonding mask, because it must program that into PGID_DST. Additionally, it must also clear the inactive ports from the bond mask here, which it can't do if bond_mask just contains the active ports: ac = ocelot_read_rix(ocelot, ANA_PGID_PGID, i); ac &= ~bond_mask; <---- here /* Don't do division by zero if there was no active * port. Just make all aggregation codes zero. */ if (num_active_ports) ac |= BIT(aggr_idx[i % num_active_ports]); ocelot_write_rix(ocelot, ac, ANA_PGID_PGID, i); So it becomes the responsibility of ocelot_set_aggr_pgids() to take ocelot_port->lag_tx_active into consideration when populating the aggr_idx array. Fixes: 23ca3b72 ("net: mscc: ocelot: rebalance LAGs on link up/down events") Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== 40GbE Intel Wired LAN Driver Updates 2022-01-07 This series contains updates to i40e and iavf drivers. Karen limits per VF MAC filters so that one VF does not consume all filters for i40e. Jedrzej reduces busy wait time for admin queue calls for i40e. Mateusz updates firmware versions to reflect new supported NVM images and renames an error to remove non-inclusive language for i40e. Yang Li fixes a set but not used warning for i40e. Jason Wang removes an unneeded variable for iavf. * '40GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: iavf: remove an unneeded variable i40e: remove variables set but not used i40e: Remove non-inclusive language i40e: Update FW API version i40e: Minimize amount of busy-waiting during AQ send i40e: Add ensurance of MacVlan resources for every trusted VF ==================== Link: https://lore.kernel.org/r/20220107175704.438387-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Gal Pressman authored
The cited Fixes commit introduced a memory leak when running kTLS traffic (with/without hardware offloads). I'm running nginx on the server side and wrk on the client side and get the following: unreferenced object 0xffff8881935e9b80 (size 224): comm "softirq", pid 0, jiffies 4294903611 (age 43.204s) hex dump (first 32 bytes): 80 9b d0 36 81 88 ff ff 00 00 00 00 00 00 00 00 ...6............ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<00000000efe2a999>] build_skb+0x1f/0x170 [<00000000ef521785>] mlx5e_skb_from_cqe_mpwrq_linear+0x2bc/0x610 [mlx5_core] [<00000000945d0ffe>] mlx5e_handle_rx_cqe_mpwrq+0x264/0x9e0 [mlx5_core] [<00000000cb675b06>] mlx5e_poll_rx_cq+0x3ad/0x17a0 [mlx5_core] [<0000000018aac6a9>] mlx5e_napi_poll+0x28c/0x1b60 [mlx5_core] [<000000001f3369d1>] __napi_poll+0x9f/0x560 [<00000000cfa11f72>] net_rx_action+0x357/0xa60 [<000000008653b8d7>] __do_softirq+0x282/0x94e [<00000000644923c6>] __irq_exit_rcu+0x11f/0x170 [<00000000d4085f8f>] irq_exit_rcu+0xa/0x20 [<00000000d412fef4>] common_interrupt+0x7d/0xa0 [<00000000bfb0cebc>] asm_common_interrupt+0x1e/0x40 [<00000000d80d0890>] default_idle+0x53/0x70 [<00000000f2b9780e>] default_idle_call+0x8c/0xd0 [<00000000c7659e15>] do_idle+0x394/0x450 I'm not familiar with these areas of the code, but I've added this sk_defer_free_flush() to tls_sw_recvmsg() based on a hunch and it resolved the issue. Fixes: f35f8219 ("tcp: defer skb freeing after socket lock is released") Signed-off-by:Gal Pressman <gal@nvidia.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Link: https://lore.kernel.org/r/20220102081253.9123-1-gal@nvidia.comSigned-off-by:
-
- 07 Jan, 2022 35 commits
-
-
Jason Wang authored
The variable `ret_code' used for returning is never changed in function `iavf_shutdown_adminq'. So that it can be removed and just return its initial value 0 at the end of `iavf_shutdown_adminq' function. Signed-off-by:
Jason Wang <wangborong@cdjrlc.com> Signed-off-by:
Tony Nguyen <anthony.l.nguyen@intel.com>
-
Yang Li authored
The code that uses variables pe_cntx_size and pe_filt_size has been removed, so they should be removed as well. Eliminate the following clang warnings: drivers/net/ethernet/intel/i40e/i40e_common.c:4139:20: warning: variable 'pe_filt_size' set but not used. drivers/net/ethernet/intel/i40e/i40e_common.c:4139:6: warning: variable 'pe_cntx_size' set but not used. Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Yang Li <yang.lee@linux.alibaba.com> Tested-by:
Gurucharan G <gurucharanx.g@intel.com> Signed-off-by:
-
Mateusz Palczewski authored
Remove non-inclusive language from the driver. Signed-off-by:
Aleksandr Loktionov <aleksandr.loktionov@intel.com> Signed-off-by:
Mateusz Palczewski <mateusz.palczewski@intel.com> Signed-off-by:
-
Mateusz Palczewski authored
Update FW API versions to the newest supported NVM images. Signed-off-by:
Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com> Signed-off-by:
-
Jedrzej Jagielski authored
The i40e_asq_send_command will now use a non blocking usleep_range if possible (non-atomic context), instead of busy-waiting udelay. The usleep_range function uses hrtimers to provide better performance and removes the negative impact of busy-waiting in time-critical environments. 1. Rename i40e_asq_send_command to i40e_asq_send_command_atomic and add 5th parameter to inform if called from an atomic context. Call inside usleep_range (if non-atomic) or udelay (if atomic). 2. Change i40e_asq_send_command to invoke i40e_asq_send_command_atomic(..., false). 3. Change two functions: - i40e_aq_set_vsi_uc_promisc_on_vlan - i40e_aq_set_vsi_mc_promisc_on_vlan to explicitly use i40e_asq_send_command_atomic(..., true) instead of i40e_asq_send_command, as they use spinlocks and do some work in an atomic context. All other calls to i40e_asq_send_command remain unchanged. Signed-off-by:Dawid Lukwinski <dawid.lukwinski@intel.com> Signed-off-by:
Jedrzej Jagielski <jedrzej.jagielski@intel.com> Tested-by:
Tony Brelinski <tony.brelinski@intel.com> Signed-off-by:
-
Karen Sornek authored
Trusted VF can use up every resource available, leaving nothing to other trusted VFs. Introduce define, which calculates MacVlan resources available based on maximum available MacVlan resources, bare minimum for each VF and number of currently allocated VFs. Signed-off-by:
Przemyslaw Patynowski <przemyslawx.patynowski@intel.com> Signed-off-by:
Karen Sornek <karen.sornek@intel.com> Tested-by:
-
Kevin Bracey authored
Documentation incorrectly stated that CS1 is equivalent to LE for diffserv8. But when LE was added to the table, CS1 was pushed into tin 1, leaving only LE in tin 0. Also "TOS1" no longer exists, as that is the same codepoint as LE. Make other tweaks properly distinguishing codepoints from classes and putting current Diffserve codepoints ahead of legacy ones. Signed-off-by:
Kevin Bracey <kevin@bracey.fi> Acked-by:
Toke Høiland-Jørgensen <toke@toke.dk> Link: https://lore.kernel.org/r/20220106215637.3132391-1-kevin@bracey.fiSigned-off-by:
-
David S. Miller authored
Mat Martineau says: ==================== mptcp: New features and cleanup These patches have been tested in the MPTCP tree for a longer than usual time (thanks to holiday schedules), and are ready for the net-next branch. Changes include feature updates, small fixes, refactoring, and some selftest changes. Patch 1 fixes an OUTQ ioctl issue with TCP fallback sockets. Patches 2, 3, and 6 add support of the MPTCP fastclose option (quick shutdown of the full MPTCP connection, similar to TCP RST in regular TCP), and a related self test. Patch 4 cleans up some accept and poll code that is no longer needed after the fastclose changes. Patch 5 add userspace disconnect using AF_UNSPEC, which is used when testing fastclose and makes the MPTCP socket's handling of AF_UNSPEC in connect() more TCP-like. Patches 7-11 refactor subflow creation to make better use of multiple local endpoints and to better handle individual connection failures when creating multiple subflows. Includes self test updates. Patch 12 cleans up the way subflows are added to the MPTCP connection list, eliminating the need for calls throughout the MPTCP code that had to check the intermediate "join list" for entries to shift over to the main "connection list". Patch 13 refactors the MPTCP release_cb flags to use separate storage for values only accessed with the socket lock held (no atomic ops needed), and for values that need atomic operations. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Paolo Abeni authored
Currently the msk->flags bitmask carries both state for the mptcp_release_cb() - mostly touched under the mptcp data lock - and others state info touched even outside such lock scope. As a consequence, msk->flags is always manipulated with atomic operations. This change splits such bitmask in two separate fields, so that we use plain bit operations when touching the cb-related info. The MPTCP_PUSH_PENDING bit needs additional care, as it is the only CB related field currently accessed either under the mptcp data lock or the mptcp socket lock. Let's add another mask just for such bit's sake. Signed-off-by:
-
Paolo Abeni authored
We can simplify the join list handling leveraging the mptcp_release_cb(): if we can acquire the msk socket lock at mptcp_finish_join time, move the new subflow directly into the conn_list, otherwise place it on join_list and let the release_cb process such list. Since pending MPJ connection are now always processed in a timely way, we can avoid flushing the join list every time we have to process all the current subflows. Additionally we can now use the mptcp data lock to protect the join_list, removing the additional spin lock. Finally, the MPJ handshake is now always finalized under the msk socket lock, we can drop the additional synchronization between mptcp_finish_join() and mptcp_close(). Signed-off-by:
-
Paolo Abeni authored
Verify that, when multiple endpoints are available, subflows creation proceed even when the first additional subflow creation fails - due to packet drop on the relevant link Co-developed-by:
Geliang Tang <geliang.tang@suse.com> Signed-off-by:
-
Paolo Abeni authored
If the MPTCP configuration allows for multiple subflows creation, and the first additional subflows never reach the fully established status - e.g. due to packets drop or reset - the in kernel path manager do not move to the next subflow. This patch introduces a new PM helper to cope with MPJ subflow creation failure and delay and hook it where appropriate. Such helper triggers additional subflow creation, as needed and updates the PM subflow counter, if the current one is closing. Additionally start all the needed additional subflows as soon as the MPTCP socket is fully established, so we don't have to cope with slow MPJ handshake blocking the next subflow creation. Signed-off-by:
-
Paolo Abeni authored
Include into the path manager status a bitmap tracking the list of local endpoints still available - not yet used - for the relevant mptcp socket. Keep such map updated at endpoint creation/deletion time, so that we can easily skip already used endpoint at local address selection time. The endpoint used by the initial subflow is lazyly accounted at subflow creation time: the usage bitmap is be up2date before endpoint selection and we avoid such unneeded task in some relevant scenarios - e.g. busy servers accepting incoming subflows but not creating any additional ones nor annuncing additional addresses. Overall this allows for fair local endpoints usage in case of subflow failure. As a side effect, this patch also enforces that each endpoint is used at most once for each mptcp connection. Signed-off-by:
-
Paolo Abeni authored
Check for all MPJ variant at once, this reduces the number of conditionals traversed on average and will simplify the next patch. No functional change intended. Signed-off-by:
-
Paolo Abeni authored
Since full-mesh endpoint support, the reception of a single ADD_ADDR option can cause multiple subflows creation. When such option is accepted we increment 'add_addr_accepted' by one. When we received a paired RM_ADDR option, we deleted all the relevant subflows, decrementing 'add_addr_accepted' by one for each of them. We have a similar issue for 'local_addr_used' Fix them moving the pm endpoint accounting outside the subflow traversal. Fixes: 1a0d6136 ("mptcp: local addresses fullmesh") Signed-off-by:
-
Paolo Abeni authored
Performs several disconnect/reconnect on the same socket, ensuring the overall transfer is succesful. The new test leverages ioctl(SIOCOUTQ) to ensure all the pending data is acked before disconnecting. Additionally order alphabetically the test program arguments list for better maintainability. Signed-off-by:
-
Paolo Abeni authored
Handle explicitly AF_UNSPEC in mptcp_stream_connnect() to allow user-space to disconnect established MPTCP connections Signed-off-by:
-
Paolo Abeni authored
After the previous patch, msk->subflow will never be deleted during the whole msk lifetime. We don't need anymore to acquire references to it in mptcp_stream_accept() and we can use the listener subflow accept queue to simplify mptcp_poll() for listener socket. Overall this removes a lock pair and 4 more atomic operations per accept(). Signed-off-by:
-
Paolo Abeni authored
The current mptcp_disconnect() implementation lacks several steps, we additionally need to reset the msk socket state and flush the subflow list. Factor out the needed helper to avoid code duplication. Additionally ensure that the initial subflow is disposed only after mptcp_close(), just reset it at disconnect time. Signed-off-by:
-
Paolo Abeni authored
Allow the MPTCP xmit path to add MP_FASTCLOSE suboption on RST egress packets. Additionally reorder related options writing to reduce the number of conditionals required in the fast path. Co-developed-by:
Matthieu Baerts <matthieu.baerts@tessares.net> Signed-off-by:
-
Paolo Abeni authored
After shutdown, for fallback MPTCP sockets, we always have write_seq == snd_una+1 The above will foul OUTQ ioctl(). Keep snd_una in sync with write_seq even after shutdown. Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linuxDavid S. Miller authored
Saeed Mahameed says: ==================== mlx5-updates-2022-01-06 1) Expose FEC per lane block counters via ethtool 2) Trivial fixes/updates/cleanup to mlx5e netdev driver 3) Fix htmldoc build warning 4) Spread mlx5 SFs (sub-functions) to all available CPU cores: Commits 1..5 Shay Drory Says: ================ Before this patchset, mlx5 subfunction shared the same IRQs (MSI-X) with their peers subfunctions, causing them to use same CPU cores. In large scale, this is very undesirable, SFs use small number of cpu cores and all of them will be packed on the same CPU cores, not utilizing all CPU cores in the system. In this patchset we want to achieve two things. a) Spread IRQs used by SFs to all cpu cores b) Pack less SFs in the same IRQ, will result in multiple IRQs per core. In this patchset, we spread SFs over all online cpus available to mlx5 irqs in Round-Robin manner. e.g.: Whenever a SF is created, pick the next CPU core with least number of SF IRQs bound to it, SFs will share IRQs on the same core until a certain limit, when such limit is reached, we request a new IRQ and add it to that CPU core IRQ pool, when out of IRQs, pick any IRQ with least number of SF users. This enhancement is done in order to achieve a better distribution of the SFs over all the available CPUs, which reduces application latency, as shown bellow. Machine details: Intel(R) Xeon(R) CPU E5-2697 v3 @ 2.60GHz with 56 cores. PCI Express 3 with BW of 126 Gb/s. ConnectX-5 Ex; EDR IB (100Gb/s) and 100GbE; dual-port QSFP28; PCIe4.0 x16. Base line test description: Single SF on the system. One instance of netperf is running on-top the SF. Numbers: latency = 15.136 usec, CPU Util = 35% Test description: There are 250 SFs on the system. There are 3 instances of netperf running, on-top three different SFs, in parallel. Perf numbers: # netperf SFs latency(usec) latency CPU utilization affinity affinity (lower is better) increase % 1 cpu=0 cpu={0} ~23 (app 1-3) 35% 75% 2 cpu=0,2,4 cpu={0} app 1: 21.625 30% 68% (CPU 0) app 2-3: 16.5 9% 15% (CPU 2,4) 3 cpu=0 cpu={0,2,4} app 1: ~16 7% 84% (CPU 0) app 2-3: ~17.9 14% 22% (CPU 2,4) 4 cpu=0,2,4 cpu={0,2,4} 15.2 (app 1-3) 0% 33% (CPU 0,2,4) - The first two entries (#1 and #2) show current state. e.g.: SFs are using the same CPU. The last two entries (#3 and #4) shows the latency reduction improvement of this patch. e.g.: SFs are on different CPUs. - Whenever we use several CPUs, in case there is a different CPU utilization, write the utilization of each CPU separately. - Whenever the latency result of the netperf instances were different, write the latency of each netperf instances separately. Commands: - for netperf CPU=0: $ for i in {1..3}; do taskset -c 0 netperf -H 1${i}.1.1.1 -t TCP_RR -- \ -o RT_LATENCY -r8 & done - for netperf CPU=0,2,4 $ for i in {1..3}; do taskset -c $(( ($i - 1) * 2 )) netperf -H \ 1${i}.1.1.1 -t TCP_RR -- -o RT_LATENCY -r8 & done ================ ==================== Signed-off-by: -
git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queueJakub Kicinski authored
Tony Nguyen says: ==================== 100GbE Intel Wired LAN Driver Updates 2022-01-06 Victor adds restoring of advanced rules after reset. Wojciech improves usage of switchdev control VSI by utilizing the device's advanced rules for forwarding. Christophe Jaillet removes some unneeded calls to zero bitmaps, changes some bitmap operations that don't need to be atomic, and converts a kfree() to a more appropriate bitmap_free(). * '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue: ice: Use bitmap_free() to free bitmap ice: Optimize a few bitmap operations ice: Slightly simply ice_find_free_recp_res_idx ice: improve switchdev's slow-path ice: replay advanced rules after reset ==================== Link: https://lore.kernel.org/r/20220106183013.3777622-1-anthony.l.nguyen@intel.comSigned-off-by:
-
Jakub Kicinski authored
Ido Schimmel says: ==================== mlxsw: Add Spectrum-4 support This patchset adds Spectrum-4 support in mlxsw. It builds on top of a previous patchset merged in commit 10184da9 ("Merge branch 'mlxsw-Spectrum-4-prep'") and makes two additional changes before adding Spectrum-4 support. Patchset overview: Patches #1-#2 add a few Spectrum-4 specific variants of existing ACL keys. The new variants are needed because the size of certain key elements (e.g., local port) was increased in Spectrum-4. Patches #3-#6 are preparations. Patch #7 implements the Spectrum-4 variant of the Bloom filter hash function. The Bloom filter is used to optimize ACL lookups by potentially skipping certain lookups if they are guaranteed not to match. See additional info in merge commit ae6750e0 ("Merge branch 'mlxsw-spectrum_acl-Add-Bloom-filter-support'"). Patch #8 finally adds Spectrum-4 support. ==================== Link: https://lore.kernel.org/r/20220106160652.821176-1-idosch@nvidia.comSigned-off-by:
-
Amit Cohen authored
Extend existing driver for Spectrum, Spectrum-2 and Spectrum-3 ASICs to support Spectrum-4 ASIC as well. Currently there is no released firmware version for Spectrum-4, so the driver is not enforcing a minimum version. Signed-off-by:
Amit Cohen <amcohen@nvidia.com> Signed-off-by:
Ido Schimmel <idosch@nvidia.com> Signed-off-by:
-
Amit Cohen authored
Spectrum-4 will calculate hash function for bloom filter differently from the existing ASICs. First, two hash functions will be used to calculate 16 bits result. The final result will be combination of the two results - 6 bits which are result of CRC-6 will be used as MSB and 10 bits which are result of CRC-10 will be used as LSB. Second, while in Spectrum{2,3}, there is a padding in each chunk, so the chunks use a sequence of whole bytes, in Spectrum-4 there is no padding, so each chunk use 20 bytes minus 2 bits, so it is necessary to align the chunks to be without holes. Add dedicated 'mlxsw_sp_acl_bf_ops' for Spectrum-4 and add the required tables for CRC calculations. All the details are documented as part of the code for future use. Signed-off-by:Petr Machata <petrm@nvidia.com> Signed-off-by:
-
Amit Cohen authored
Spectrum-4 will calculate hash function for bloom filter differently from the existing ASICs. There are two changes: 1. Instead of using one hash function to calculate 16 bits output (CRC-16), two functions will be used. 2. The chunks will be built differently, without padding. As preparation for support of Spectrum-4 bloom filter, add 'ops' structure to allow handling different calculation for different ASICs. Signed-off-by:
-
Amit Cohen authored
Spectrum-4 will calculate hash function for bloom filter differently from the existing ASICs. There are two changes: 1. Instead of using one hash function to calculate 16 bits output (CRC-16), two functions will be used. 2. The chunks will be built differently, without padding. As preparation for support of Spectrum-4 bloom filter, rename CRC table to include "sp2" prefix and "crc16", as next patch will add two additional tables. In addition, rename all the dedicated functions and defines for Spectrum-{2,3} to include "sp2" prefix. Signed-off-by: -
Amit Cohen authored
Spectrum-4 will calculate hash function for bloom filter differently from the existing ASICs. One of the changes is related to the way that the chunks will be build - without padding. As preparation for support of Spectrum-4 bloom filter, make mlxsw_sp_acl_bf_key_encode() more flexible, so it will be able to use it for Spectrum-4 as well. Signed-off-by:
-
Amit Cohen authored
Currently, mlxsw_sp_acl_bf_rule_count_index_get() is implemented before mlxsw_sp_acl_bf_index_get() but is used after it. Adding a new function for Spectrum-4 would make them further apart still. Fix by moving them around. Signed-off-by:
-
Amit Cohen authored
Spectrum-4 ASIC will support more virtual routers and local ports compared to the existing ASICs. Therefore, the virtual router and local port ACL key elements need to be increased. Introduce new key elements for Spectrum-4 to be aligned with the elements used already for other Spectrum ASICs. The key blocks layout is the same for Spectrum-4, so use the existing code for encode_block() and clear_block(), just create separate blocks. Note that size of `VIRT_ROUTER_MSB` is 4 bits in Spectrum-4, therefore declare it using `MLXSW_AFK_ELEMENT_INST_U32()`, in order to be able to set `.avoid_size_check` to true. Otherwise, `mlxsw_afk_blocks_check()` will fail and warn. Signed-off-by:
-
Amit Cohen authored
In Spectrum-4, the size of the virtual router ACL key element increased from 11 bits to 12 bits. In order to reuse the existing virtual router ACL key element enumerators for Spectrum-4, rename 'VIRT_ROUTER_8_10' and 'VIRT_ROUTER_0_7' to 'VIRT_ROUTER_MSB' and 'VIRT_ROUTER_LSB', respectively. No functional changes intended. Signed-off-by:
-
Jakub Kicinski authored
Ioana Ciornei says: ==================== dpaa2-eth: small cleanup These 3 patches are just part of a small cleanup on the dpaa2-eth and the dpaa2-switch drivers. In case we are hitting a case in which the fwnode of the root dprc device we initiate a deferred probe. On the dpaa2-switch side, if we are on the remove path, make sure that we check for a non-NULL pointer before accessing the port private structure. ==================== Link: https://lore.kernel.org/r/20220106135905.81923-1-ioana.ciornei@nxp.comSigned-off-by:
-
Ioana Ciornei authored
Before accessing the port private structure make sure that there is still a non-NULL pointer there. A NULL pointer access can happen when we are on the remove path, some switch ports are unregistered and some are in the process of unregistering. Signed-off-by:
Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by:
-
Ioana Ciornei authored
We could get into a situation when the fwnode of the parent device is not yet set because its probe didn't yet finish. When this happens, any caller of the dpaa2_mac_open() will not have the fwnode available, thus cause problems at the PHY connect time. Avoid this by just returning -EPROBE_DEFER from the dpaa2_mac_open when this happens. Signed-off-by:
-
