Fixes the following randconfig build error:

 ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
 simple-mfd-i2c.c:(.text+0x48): undefined reference to `__devm_regmap_init_i2c'
 ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_init':
 simple-mfd-i2c.c:(.init.text+0x14): undefined reference to `i2c_register_driver'
 ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_driver_exit':
 simple-mfd-i2c.c:(.exit.text+0xd): undefined reference to `i2c_del_driver'
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Build this driver on another platforms if COMPILE_TEST=y. Another
drivers may depend on this, for example leds-asic3.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted same
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com> # for BD70528
Acked-by: Tim Harvey <tharvey@gateworks.com> # for gateworks-gsc.yaml
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Recent Kontron COMe modules identify the PLD device using the hardware
id KEM0001 in the ACPI table.
This patch adds support for probing the device using the HID and also
retrieving the resources.

As this is not available for all products, the DMI based detection still
needs to be around for older systems. It is executed if no matching ACPI
HID is found during registering the platform driver or no specific
device id is forced.
If a device is detected using ACPI and no resource information is
available, the default io resource is used.

Forcing a device id with the force_device_id parameter and therefore
manually generating a platform device takes precedence over ACPI during
probing.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This patch implements the basic functions of the BMC chip for some Intel
FPGA PCIe Acceleration Cards (PAC). The BMC is implemented using the
Intel MAX 10 CPLD.

This BMC chip is connected to the FPGA by a SPI bus. To provide direct
register access from the FPGA, the "SPI slave to Avalon Master Bridge"
(spi-avmm) IP is integrated in the chip. It converts encoded streams of
bytes from the host to the internal register read/write on the Avalon
bus. So This driver uses the regmap-spi-avmm for register accessing.
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Wu Hao <hao.wu@intel.com>
Signed-off-by: Matthew Gerlach <matthew.gerlach@linux.intel.com>
Signed-off-by: Russ Weight <russell.h.weight@intel.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the LP87524B/J/P-Q1 Four 4-MHz Buck Converter. This is a
variant of the LP87565 having 4 single-phase outputs and up to 10 A of
total output current.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the LP87524-Q1 to the bindings along with an example. This is a variant
of the LP87565-Q1 and LP87561-Q1 chips which already have bindings.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Also apply a few smaller improvements:

 - document that the only possible I2C slave address is 0x60 as per the
   datasheet and fix the second example accordingly
 - The definition of "xxx-in-supply" was generic, thus define in detail the
   possible cases for each chip variant
 - remove "MFD driver" from the title as it is implementation specific
 - replace "PMIC" with "buck converter" in title as it is more informative
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This file does not make use of it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This code should clean up if sm501_init_dev() fails.

Fixes: b6d6454f ("[PATCH] mfd: SM501 core driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The name allocated for the regmap_config structure is freed
pretty early, right after the registration of the MMIO region.

Unfortunately, that doesn't follow the life cycle that debugfs
expects, as it can access the name field long after the free
has occurred.

Move the free on the error path, and keep it forever otherwise.

Fixes: e15d7f2b ("mfd: syscon: Use a unique name with regmap_config")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Document Samsung Exynos3 and Exynos5433 compatibles for system
registers.
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The Samsung Exynos System Registers (Sysreg) bindings are quite simple -
just additional compatible to the syscon.  They do not have any value so
merge them into generic MFD syscon bindings.
Suggested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There are stray Unicode quotation marks (U+201C	DOUBLE TURNED COMMA
QUOTATION MARK) in the file. Remove them, as they don't serve a purpose.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When changing to use suspend-to-idle to save power, the PMIC irq can not
wakeup the system due to lack of wakeup capability, which will cause
the sub-irqs (such as power key) of the PMIC can not wake up the system.
Thus we can add the wakeup capability for PMIC irq to solve this issue,
as well as removing the IRQF_NO_SUSPEND flag to allow PMIC irq to be
a wakeup source.
Reported-by: Chunyan Zhang <zhang.lyra@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang7@gmail.com>
Tested-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add PCI IDs for Lakefield to the list of supported UARTs.

Cc: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: "Ravi V. Shankar" <ravi.v.shankar@intel.com>
Signed-off-by: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This converts the DaVinci DM355EVM LEDs to use GPIO descriptor look-ups.

Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Common pattern of handling deferred probe can be simplified with
dev_err_probe().  Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

This driver provides access to the EC RAM of said embedded controller
attached to the I2C bus as well as optionally supporting its slightly weird
power-off/restart protocol.

A particular implementation of the EC firmware can be identified by a
model byte. If this driver identifies the Dell Ariel platform, it
registers the appropriate cells.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add binding document for the ENE KB3930 Embedded Controller.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

When testing with !OF, the build system reports:

>> drivers/mfd/khadas-mcu.c:125:34: warning: unused variable 'khadas_mcu_of_match' [-Wunused-const-variable]
   static const struct of_device_id khadas_mcu_of_match[] = {
                                    ^
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

The RN5T618 and RC5T619 both have a charger and a fuel gauge, so add
a subdevice for it. According to drivers in the wild, things
should be at least similar, but since it is not tested, add it
only to the RC5T619.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

individul -> individual
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the hardware monitoring controller of the sl28cpld board
management controller. This driver is part of a multi-function device.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.

A controller has 8 lines. There are three different flavors:
full-featured GPIO with interrupt support, input-only and output-only.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the PWM controller of the sl28cpld board management
controller. This is part of a multi-function device driver.

The controller has one PWM channel and can just generate four distinct
frequencies.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the watchdog of the sl28cpld board management
controller. This is part of a multi-function device driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add support for the interrupt controller inside the sl28 CPLD management
controller.

The interrupt controller can handle at most 8 interrupts and is really
simplistic and consists only of an interrupt mask and an interrupt
pending register.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add the core support for the board management controller found on the
SMARC-sAL28 board.

Also add a virtual symbol which pulls in the simple-mfd-i2c driver and
provide a common symbol on which the subdevice drivers can depend on.

At the moment, this controller is used on the Kontron SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Add a device tree bindings for the board management controller found on
the Kontron SMARC-sAL28 board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

There are I2C devices which contain several different functions but
doesn't require any special access functions. For these kind of drivers
an I2C regmap should be enough.

Create an I2C driver which creates an I2C regmap and enumerates its
children. If a device wants to use this as its MFD core driver, it has
to add an individual compatible string. It may provide its own regmap
configuration.

Subdevices can use dev_get_regmap() on the parent to get their regmap
instance.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull io_uring fixes from Jens Axboe:
 "A few differerent things in here.

  Seems like syzbot got some more io_uring bits wired up, and we got a
  handful of reports and the associated fixes are in here.

  General fixes too, and a lot of them marked for stable.

  Lastly, a bit of fallout from the async buffered reads, where we now
  more easily trigger short reads. Some applications don't really like
  that, so the io_read() code now handles short reads internally, and
  got a cleanup along the way so that it's now easier to read (and
  documented). We're now passing tests that failed before"

* tag 'io_uring-5.9-2020-08-15' of git://git.kernel.dk/linux-block:
  io_uring: short circuit -EAGAIN for blocking read attempt
  io_uring: sanitize double poll handling
  io_uring: internally retry short reads
  io_uring: retain iov_iter state over io_read/io_write calls
  task_work: only grab task signal lock when needed
  io_uring: enable lookup of links holding inflight files
  io_uring: fail poll arm on queue proc failure
  io_uring: hold 'ctx' reference around task_work queue + execute
  fs: RWF_NOWAIT should imply IOCB_NOIO
  io_uring: defer file table grabbing request cleanup for locked requests
  io_uring: add missing REQ_F_COMP_LOCKED for nested requests
  io_uring: fix recursive completion locking on oveflow flush
  io_uring: use TWA_SIGNAL for task_work uncondtionally
  io_uring: account locked memory before potential error case
  io_uring: set ctx sq/cq entry count earlier
  io_uring: Fix NULL pointer dereference in loop_rw_iter()
  io_uring: add comments on how the async buffered read retry works
  io_uring: io_async_buf_func() need not test page bit

Commit 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one()
and pmd_free_one()") converted parisc to use generic version of
pmd_alloc_one() but it missed the fact that parisc uses order-1 pages for
PMD.

Restore the original version of pmd_alloc_one() for parisc, just use
GFP_PGTABLE_KERNEL that implies __GFP_ZERO instead of GFP_KERNEL and
memset.

Fixes: 1355c31e ("asm-generic: pgalloc: provide generic pmd_alloc_one() and pmd_free_one()")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Link: https://lkml.kernel.org/r/9f2b5ebd-e4a4-0fa1-6cd3-4b9f6892d1ad@linux.eeSigned-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull block fixes from Jens Axboe:
 "A few fixes on the block side of things:

   - Discard granularity fix (Coly)

   - rnbd cleanups (Guoqing)

   - md error handling fix (Dan)

   - md sysfs fix (Junxiao)

   - Fix flush request accounting, which caused an IO slowdown for some
     configurations (Ming)

   - Properly propagate loop flag for partition scanning (Lennart)"

* tag 'block-5.9-2020-08-14' of git://git.kernel.dk/linux-block:
  block: fix double account of flush request's driver tag
  loop: unset GENHD_FL_NO_PART_SCAN on LOOP_CONFIGURE
  rnbd: no need to set bi_end_io in rnbd_bio_map_kern
  rnbd: remove rnbd_dev_submit_io
  md-cluster: Fix potential error pointer dereference in resize_bitmaps()
  block: check queue's limits.discard_granularity in __blkdev_issue_discard()
  md: get sysfs entry after redundancy attr group create

Pull RISC-V fix from Palmer Dabbelt:
 "I collected a single fix during the merge window: we managed to break
  the early trap setup on !MMU, this fixes it"

* tag 'riscv-for-linus-5.9-mw1' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
  riscv: Setup exception vector for nommu platform

Pull arch/sh updates from Rich Felker:
 "Cleanup, SECCOMP_FILTER support, message printing fixes, and other
  changes to arch/sh"

* tag 'sh-for-5.9' of git://git.libc.org/linux-sh: (34 commits)
  sh: landisk: Add missing initialization of sh_io_port_base
  sh: bring syscall_set_return_value in line with other architectures
  sh: Add SECCOMP_FILTER
  sh: Rearrange blocks in entry-common.S
  sh: switch to copy_thread_tls()
  sh: use the generic dma coherent remap allocator
  sh: don't allow non-coherent DMA for NOMMU
  dma-mapping: consolidate the NO_DMA definition in kernel/dma/Kconfig
  sh: unexport register_trapped_io and match_trapped_io_handler
  sh: don't include <asm/io_trapped.h> in <asm/io.h>
  sh: move the ioremap implementation out of line
  sh: move ioremap_fixed details out of <asm/io.h>
  sh: remove __KERNEL__ ifdefs from non-UAPI headers
  sh: sort the selects for SUPERH alphabetically
  sh: remove -Werror from Makefiles
  sh: Replace HTTP links with HTTPS ones
  arch/sh/configs: remove obsolete CONFIG_SOC_CAMERA*
  sh: stacktrace: Remove stacktrace_ops.stack()
  sh: machvec: Modernize printing of kernel messages
  sh: pci: Modernize printing of kernel messages
  ...

One case was missed in the short IO retry handling, and that's hitting
-EAGAIN on a blocking attempt read (eg from io-wq context). This is a
problem on sockets that are marked as non-blocking when created, they
don't carry any REQ_F_NOWAIT information to help us terminate them
instead of perpetually retrying.

Fixes: 227c0c96 ("io_uring: internally retry short reads")
Signed-off-by: Jens Axboe <axboe@kernel.dk>