These comparisons should be >= instead of > to prevent accessing one
element beyond the end of the hw->soc->pins[] array.

Fixes: 3de7deef ("pinctrl: mediatek: Check gpio pin number and use binary search in mtk_hw_pin_field_lookup()")
Fixes: 184d8e13 ("pinctrl: mediatek: Add support for pin configuration dump via debugfs.")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200218055247.74s2xa7veqx2do34@kili.mountainReviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

In the second loop of ingenic_pinconf_set(), it annotates the switch
default case as unreachable().  The annotation is technically correct,
because that same case would have resulted in an early function return
in the previous loop.

However, the compiled code is suboptimal.  GCC seems to work extra hard
to ensure that the unreachable code path triggers undefined behavior.
The function would fall through to start executing whatever function
happens to be next in the compilation unit.

This is problematic because:

  a) it adds unnecessary 'ensure undefined behavior' logic, and
     corresponding i-cache footprint; and

  b) it's less robust -- if a bug were to be introduced, falling through
     to the next function would be catastrophic.

Yet another issue is that, while objtool normally understands
unreachable() annotations, there's one special case where it doesn't:
when the annotation occurs immediately after a 'ret' instruction.  That
happens to be the case here because unreachable() is immediately before
the return.

Remove the unreachable() annotation and replace it with a comment.  This
simplifies the code generation and changes the unreachable error path to
just silently return instead of corrupting execution.

This fixes the following objtool warning:

  drivers/pinctrl/pinctrl-ingenic.o: warning: objtool: ingenic_pinconf_set() falls through to next function ingenic_pinconf_group_set()
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Link: https://lore.kernel.org/r/bc20fdbcb826512cf76b7dfd0972740875931b19.1582212881.git.jpoimboe@redhat.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add missing gpio definition for mdio and rgmii2.
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Link: https://lore.kernel.org/r/20200219175940.744-1-ansuelsmth@gmail.comAcked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The items of mux_reg/conf_reg/input_reg/mux_val/input_val/pad_setting
should be uint32-matrix instead of uint32-array, fix it and improve the
schema and example.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1582012300-30260-4-git-send-email-Anson.Huang@nxp.comReviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the i.MX8MN pinctrl binding to DT schema format using json-schema
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1582012300-30260-3-git-send-email-Anson.Huang@nxp.comReviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the i.MX8MM pinctrl binding to DT schema format using json-schema
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1582012300-30260-2-git-send-email-Anson.Huang@nxp.comReviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Convert the i.MX8MQ pinctrl binding to DT schema format using json-schema
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1582012300-30260-1-git-send-email-Anson.Huang@nxp.comReviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Link: https://lore.kernel.org/r/20200217185437.GA20901@embeddedorAcked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add lcd pinctrl driver for X1830.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/1581851828-3493-3-git-send-email-zhouyanjie@wanyeetech.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.

Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.

Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomainSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The pin controller hardware does not distinguish IRQs intended for
wakeup from other IRQs, so we must mask non-wakeup IRQs in software to
prevent inadvertent wakeups. This is accomplished at the irqchip level
via the IRQCHIP_MASK_ON_SUSPEND flag.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200117213340.47714-2-samuel@sholland.orgAcked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The pinctrl irqchip may be connected to an irqchip that implements the
.irq_set_wake callback, such as the R_INTC on A31 and newer sunxi SoCs.
In order for GPIOs to be able to trigger wakeup, the IRQ from the
pinctrl to the upper irqchip must also be enabled for wakeup. Since the
kernel's IRQ core already manages the "wake_depth" of each IRQ, no
additional accounting is needed in the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20200117213340.47714-1-samuel@sholland.orgAcked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c: In function mtk_hw_pin_field_lookup:
drivers/pinctrl/mediatek/pinctrl-mtk-common-v2.c:70:39: warning:
 variable e set but not used [-Wunused-but-set-variable]

Since commit 3de7deef ("pinctrl: mediatek: Check gpio pin
number and use binary search in mtk_hw_pin_field_lookup()"),
it is not used any more, so remove it, also remove redundant
assignment to variable c, it will be assigned a new value later
before used.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20200218023625.14324-1-yuehaibing@huawei.comSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

The DA9062 is a mfd pmic device which supports 5 GPIOs. The GPIOs can
be used as input, output or have a special use-case.

The patch adds the support for the normal input/output use-case.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20200108104746.1765-4-m.felsch@pengutronix.deReviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Run parse-maintainers.pl and choose PIN CONTROLLER records.
Fix them accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200128154949.66521-1-andriy.shevchenko@linux.intel.comReviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The BCM2711 supports 58 GPIOs. So extend pinctrl and GPIOs accordingly.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1581166975-22949-4-git-send-email-stefan.wahren@i2se.comReviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This prepares the platform data to be easier to extend for more GPIOs.
Except of this there is no functional change.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1581166975-22949-3-git-send-email-stefan.wahren@i2se.comReviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

There is no usage for this define, so drop it.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1580148908-4863-2-git-send-email-stefan.wahren@i2se.comReviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Group names by function do not match their respective structures and
documentation defined names.

This fixes following errors when groups names defined on documentation are used:
[    4.262778] pinctrl-s700 e01b0000.pinctrl: invalid group "sd0_d1_mfp" for function "sd0"
[    4.271394] pinctrl-s700 e01b0000.pinctrl: invalid group "sd0_d2_d3_mfp" for function "sd0"
[    4.280248] pinctrl-s700 e01b0000.pinctrl: invalid group "sd1_d0_d3_mfp" for function "sd0"
[    4.289122] pinctrl-s700 e01b0000.pinctrl: invalid group "sd0_cmd_mfp" for function "sd0"

Fixes: 81c9d563 (pinctrl: actions: Add Actions Semi S700 pinctrl driver)
Signed-off-by: Matheus Castello <matheus@castello.eng.br>
Link: https://lore.kernel.org/r/20200124133758.10089-1-matheus@castello.eng.brReviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add support for pin configuration dump via catting
/sys/kernel/debug/pinctrl/$platform_dependent_path/pinconf-pins.
pinctrl framework had already support such dump. This patch implement the
operation function pointer to fullfill this dump.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-6-git-send-email-light.hsieh@mediatek.comAcked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Refine mtk_pinconf_set()/mtk_pinconf_get() for backward compatibility to
previous MediaTek's bias-pull usage.
In PINCTRL_MTK that use pinctrl-mtk-common.c, bias-pull setting for pins
with 2 pull resistors can be specified as value for bias-pull-up and
bias-pull-down. For example:
    bias-pull-up = <MTK_PUPD_SET_R1R0_00>;
    bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
    bias-pull-up = <MTK_PUPD_SET_R1R0_10>;
    bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
    bias-pull-down = <MTK_PUPD_SET_R1R0_00>;
    bias-pull-down = <MTK_PUPD_SET_R1R0_01>;
    bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
    bias-pull-down = <MTK_PUPD_SET_R1R0_11>;

On the other hand, PINCTRL_MTK_PARIS use customized properties
"mediatek,pull-up-adv" and "mediatek,pull-down-adv" to specify bias-pull
setting for pins with 2 pull resistors.
This introduce in-compatibility in device tree and increase porting
effort to MediaTek's customer that had already used PINCTRL_MTK version.
Besides, if customers are not aware of this change and still write devicetree
for PINCTRL_MTK version, they may encounter runtime failure with pinctrl and
spent time to debug.

This patch adds backward compatible to previous MediaTek's bias-pull usage
so that Mediatek's customer need not use a new devicetree property name.
The rationale is that: changing driver implementation had better leave
interface unchanged.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-5-git-send-email-light.hsieh@mediatek.comAcked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Correct cases for PIN_CONFIG_SLEW_RATE, PIN_CONFIG_INPUT_SCHMITT_ENABLE,
and PIN_CONFIG_OUTPUT_ENABLE -
Use variable ret to receive value in mtk_hw_get_value() (instead of
variable val) since pinconf_to_config_packed() at end of this function
use variable ret to pack config value.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-4-git-send-email-light.hsieh@mediatek.comAcked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1.Refine mtk_pinconf_get():
  Use only one occurrence of return at end of this function.

2.Refine mtk_pinconf_set():
2.1 Use only one occurrence of return at end of this function.
2.2 Modify case of PIN_CONFIG_INPUT_ENABLE -
2.2.1
    Regard all non-zero setting value as enable, instead of always enable.
2.2.2
    Remove check of ies_present flag and always invoke mtk_hw_set_value()
    since mtk_hw_pin_field_lookup() invoked inside mtk_hw_set_value() has
    the same effect of checking if ies control is supported.
    [The rationale is that: available of a control is always checked
     in mtk_hw_pin_field_lookup() and no need to add ies_present flag
     specially for ies control.]
2.3 Simply code logic for case of PIN_CONFIG_INPUT_SCHMITT.
2.4 Add case for PIN_CONFIG_INPUT_SCHMITT_ENABLE and process it with the
    same code for case of PIN_CONFIG_INPUT_SCHMITT.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-3-git-send-email-light.hsieh@mediatek.comAcked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

MediaTek's smartphone project actual usage does need to know current value
(in mA) in procedure of finding the best driving setting.
The steps in the procedure is like as follow:

1. set driving setting field in setting register as 0, measure waveform,
   perform test, and etc.
2. set driving setting field in setting register as 1, measure waveform,
   perform test, and etc.
...
n. set driving setting field in setting register as n-1, measure
   waveform, perform test, and etc.
Check the results of steps 1~n and adopt the setting that get best result.

This procedure does need to know the mapping between current to register
value.
Therefore, setting driving without mapping current is more practical for
MediaTek's smartphone usage.
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-2-git-send-email-light.hsieh@mediatek.comAcked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

1. Check if gpio pin number is in valid range to prevent from get invalid
   pointer 'desc' in the following code:
	desc = (const struct mtk_pin_desc *)&hw->soc->pins[gpio];

2. Improve  mtk_hw_pin_field_lookup()
2.1 Modify mtk_hw_pin_field_lookup() to use binary search for accelerating
     search.
2.2 Correct message after the following check fail:
    if (hw->soc->reg_cal && hw->soc->reg_cal[field].range) {
		rc = &hw->soc->reg_cal[field];
    The original message is:
    	"Not support field %d for pin %d (%s)\n"
    However, the check is on soc chip level, not on pin level yet.
    So the message is corrected as:
    	"Not support field %d for this soc\n"
Signed-off-by: Light Hsieh <light.hsieh@mediatek.com>
Link: https://lore.kernel.org/r/1579675994-7001-1-git-send-email-light.hsieh@mediatek.comAcked-by: Sean Wang <sean.wang@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Add initial pinctrl driver to support pin configuration with
pinctrl framework for ipq6018.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Link: https://lore.kernel.org/r/1579439601-14810-3-git-send-email-sricharan@codeaurora.orgSigned-off-by: Linus Walleij <linus.walleij@linaro.org>

Add device tree binding Documentation details for ipq6018
pinctrl driver.
Co-developed-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Signed-off-by: Rajkumar Ayyasamy <arajkuma@codeaurora.org>
Co-developed-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Signed-off-by: Selvam Sathappan Periakaruppan <speriaka@codeaurora.org>
Co-developed-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Link: https://lore.kernel.org/r/1579439601-14810-2-git-send-email-sricharan@codeaurora.orgReviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

Pull more Kbuild updates from Masahiro Yamada:

 - fix randconfig to generate a sane .config

 - rename hostprogs-y / always to hostprogs / always-y, which are more
   natual syntax.

 - optimize scripts/kallsyms

 - fix yes2modconfig and mod2yesconfig

 - make multiple directory targets ('make foo/ bar/') work

* tag 'kbuild-v5.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: make multiple directory targets work
  kconfig: Invalidate all symbols after changing to y or m.
  kallsyms: fix type of kallsyms_token_table[]
  scripts/kallsyms: change table to store (strcut sym_entry *)
  scripts/kallsyms: rename local variables in read_symbol()
  kbuild: rename hostprogs-y/always to hostprogs/always-y
  kbuild: fix the document to use extra-y for vmlinux.lds
  kconfig: fix broken dependency in randconfig-generated .config

Pull new zonefs file system from Damien Le Moal:
 "Zonefs is a very simple file system exposing each zone of a zoned
  block device as a file.

  Unlike a regular file system with native zoned block device support
  (e.g. f2fs or the on-going btrfs effort), zonefs does not hide the
  sequential write constraint of zoned block devices to the user. As a
  result, zonefs is not a POSIX compliant file system. Its goal is to
  simplify the implementation of zoned block devices support in
  applications by replacing raw block device file accesses with a richer
  file based API, avoiding relying on direct block device file ioctls
  which may be more obscure to developers.

  One example of this approach is the implementation of LSM
  (log-structured merge) tree structures (such as used in RocksDB and
  LevelDB) on zoned block devices by allowing SSTables to be stored in a
  zone file similarly to a regular file system rather than as a range of
  sectors of a zoned device. The introduction of the higher level
  construct "one file is one zone" can help reducing the amount of
  changes needed in the application while at the same time allowing the
  use of zoned block devices with various programming languages other
  than C.

  Zonefs IO management implementation uses the new iomap generic code.
  Zonefs has been successfully tested using a functional test suite
  (available with zonefs userland format tool on github) and a prototype
  implementation of LevelDB on top of zonefs"

* tag 'zonefs-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/zonefs:
  zonefs: Add documentation
  fs: New zonefs file system

In order to allow the GICv4 code to link properly on 32bit ARM,
make sure we don't use 64bit divisions when it isn't strictly
necessary.

Fixes: 4e6437f1 ("irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Zenghui Yu <yuzenghui@huawei.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull cifs fixes from Steve French:
 "13 cifs/smb3 patches, most from testing at the SMB3 plugfest this week:

   - Important fix for multichannel and for modefromsid mounts.

   - Two reconnect fixes

   - Addition of SMB3 change notify support

   - Backup tools fix

   - A few additional minor debug improvements (tracepoints and
     additional logging found useful during testing this week)"

* tag '5.6-rc-smb3-plugfest-patches' of git://git.samba.org/sfrench/cifs-2.6:
  smb3: Add defines for new information level, FileIdInformation
  smb3: print warning once if posix context returned on open
  smb3: add one more dynamic tracepoint missing from strict fsync path
  cifs: fix mode bits from dir listing when mounted with modefromsid
  cifs: fix channel signing
  cifs: add SMB3 change notification support
  cifs: make multichannel warning more visible
  cifs: fix soft mounts hanging in the reconnect code
  cifs: Add tracepoints for errors on flush or fsync
  cifs: log warning message (once) if out of disk space
  cifs: fail i/o on soft mounts if sessionsetup errors out
  smb3: fix problem with null cifs super block with previous patch
  SMB3: Backup intent flag missing from some more ops

Pull vboxfs from Al Viro:
 "This is the VirtualBox guest shared folder support by Hans de Goede,
  with fixups for fs_parse folded in to avoid bisection hazards from
  those API changes..."

* 'work.vboxsf' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  fs: Add VirtualBox guest shared folder (vboxsf) support

Pull x86 fixes from Thomas Gleixner:
 "A set of fixes for X86:

   - Ensure that the PIT is set up when the local APIC is disable or
     configured in legacy mode. This is caused by an ordering issue
     introduced in the recent changes which skip PIT initialization when
     the TSC and APIC frequencies are already known.

   - Handle malformed SRAT tables during early ACPI parsing which caused
     an infinite loop anda boot hang.

   - Fix a long standing race in the affinity setting code which affects
     PCI devices with non-maskable MSI interrupts. The problem is caused
     by the non-atomic writes of the MSI address (destination APIC id)
     and data (vector) fields which the device uses to construct the MSI
     message. The non-atomic writes are mandated by PCI.

     If both fields change and the device raises an interrupt after
     writing address and before writing data, then the MSI block
     constructs a inconsistent message which causes interrupts to be
     lost and subsequent malfunction of the device.

     The fix is to redirect the interrupt to the new vector on the
     current CPU first and then switch it over to the new target CPU.
     This allows to observe an eventually raised interrupt in the
     transitional stage (old CPU, new vector) to be observed in the APIC
     IRR and retriggered on the new target CPU and the new vector.

     The potential spurious interrupts caused by this are harmless and
     can in the worst case expose a buggy driver (all handlers have to
     be able to deal with spurious interrupts as they can and do happen
     for various reasons).

   - Add the missing suspend/resume mechanism for the HYPERV hypercall
     page which prevents resume hibernation on HYPERV guests. This
     change got lost before the merge window.

   - Mask the IOAPIC before disabling the local APIC to prevent
     potentially stale IOAPIC remote IRR bits which cause stale
     interrupt lines after resume"

* tag 'x86-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/apic: Mask IOAPIC entries when disabling the local APIC
  x86/hyperv: Suspend/resume the hypercall page for hibernation
  x86/apic/msi: Plug non-maskable MSI affinity race
  x86/boot: Handle malformed SRAT tables during early ACPI parsing
  x86/timer: Don't skip PIT setup when APIC is disabled or in legacy mode

Pull SMP fixes from Thomas Gleixner:
 "Two fixes for the SMP related functionality:

   - Make the UP version of smp_call_function_single() match SMP
     semantics when called for a not available CPU. Instead of emitting
     a warning and assuming that the function call target is CPU0,
     return a proper error code like the SMP version does.

   - Remove a superfluous check in smp_call_function_many_cond()"

* tag 'smp-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  smp/up: Make smp_call_function_single() match SMP semantics
  smp: Remove superfluous cond_func check in smp_call_function_many_cond()

Pull perf fixes from Thomas Gleixner:
 "A set of fixes and improvements for the perf subsystem:

  Kernel fixes:

   - Install cgroup events to the correct CPU context to prevent a
     potential list double add

   - Prevent an integer underflow in the perf mlock accounting

   - Add a missing prototype for arch_perf_update_userpage()

  Tooling:

   - Add a missing unlock in the error path of maps__insert() in perf
     maps.

   - Fix the build with the latest libbfd

   - Fix the perf parser so it does not delete parse event terms, which
     caused a regression for using perf with the ARM CoreSight as the
     sink configuration was missing due to the deletion.

   - Fix the double free in the perf CPU map merging test case

   - Add the missing ustring support for the perf probe command"

* tag 'perf-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf maps: Add missing unlock to maps__insert() error case
  perf probe: Add ustring support for perf probe command
  perf: Make perf able to build with latest libbfd
  perf test: Fix test case Merge cpu map
  perf parse: Copy string to perf_evsel_config_term
  perf parse: Refactor 'struct perf_evsel_config_term'
  kernel/events: Add a missing prototype for arch_perf_update_userpage()
  perf/cgroups: Install cgroup events to correct cpuctx
  perf/core: Fix mlock accounting in perf_mmap()

Pull timer fixes from Thomas Gleixner:
 "Two small fixes for the time(r) subsystem:

   - Handle a subtle race between the clocksource watchdog and a
     concurrent clocksource watchdog stop/start sequence correctly to
     prevent a timer double add bug.

   - Fix the file path for the core time namespace file"

* tag 'timers-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  clocksource: Prevent double add_timer_on() for watchdog_timer
  MAINTAINERS: Correct path to time namespace source file

Pull interrupt fixes from Thomas Gleixner:
 "A set of fixes for the interrupt subsystem:

   - Provision only ACPI enabled redistributors on GICv3

   - Use the proper command colums when building the INVALL command for
     the GICv3-ITS

   - Ensure the allocation of the L2 vPE table for GICv4.1

   - Correct the GICv4.1 VPROBASER programming so it uses the proper
     size

   - A set of small GICv4.1 tidy up patches

   - Configuration cleanup for C-SKY interrupt chip

   - Clarify the function documentation for irq_set_wake() to document
     that the wakeup functionality is orthogonal to the irq
     disable/enable mechanism"

* tag 'irq-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  irqchip/gic-v3-its: Rename VPENDBASER/VPROPBASER accessors
  irqchip/gic-v3-its: Remove superfluous WARN_ON
  irqchip/gic-v4.1: Drop 'tmp' in inherit_vpe_l1_table_from_rd()
  irqchip/gic-v4.1: Ensure L2 vPE table is allocated at RD level
  irqchip/gic-v4.1: Set vpe_l1_base for all redistributors
  irqchip/gic-v4.1: Fix programming of GICR_VPROPBASER_4_1_SIZE
  genirq: Clarify that irq wake state is orthogonal to enable/disable
  irqchip/gic-v3-its: Reference to its_invall_cmd descriptor when building INVALL
  irqchip: Some Kconfig cleanup for C-SKY
  irqchip/gic-v3: Only provision redistributors that are enabled in ACPI

Pull EFI fix from Thomas Gleixner:
 "A single fix for a EFI boot regression on X86 which was caused by the
  recent rework of the EFI memory map parsing. On systems with invalid
  memmap entries the cleanup function uses an value which cannot be
  relied on in this stage. Use the actual EFI memmap entry instead"

* tag 'efi-urgent-2020-02-09' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  efi/x86: Fix boot regression on systems with invalid memmap entries

Pull misc SCSI fixes from James Bottomley:
 "Five small patches, all in drivers or doc, which missed the initial
  pull request.

  The qla2xxx and megaraid_sas are actual fixes and the rest are
  spelling and doc changes"

* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  scsi: ufs: fix spelling mistake "initilized" -> "initialized"
  scsi: pm80xx: fix spelling mistake "to" -> "too"
  scsi: MAINTAINERS: ufs: remove pedrom.sousa@synopsys.com
  scsi: megaraid_sas: fixup MSIx interrupt setup during resume
  scsi: qla2xxx: Fix unbound NVME response length